[U-Boot] [PATCH v3 2/7] arm: usb: dra7xx: xHCI registers based on USB port index

[Igor Grinberg <grinberg@compulab.co.il>]

Hi guys,

On 02/19/17 17:15, Tom Rini wrote:
> On Sun, Feb 19, 2017 at 04:13:02PM +0100, Marek Vasut wrote:
>> On 02/19/2017 03:55 PM, Uri Mashiach wrote:
>>>
>>>
>>> On 02/19/2017 04:27 PM, Marek Vasut wrote:
>>>> On 02/19/2017 02:27 PM, Uri Mashiach wrote:
>>>>> Modify the determination of the base address of xHCI registers of DRA7XX
>>>>> targets.
>>>>> Before the commit: by the target.
>>>>> After the commit: by the USB port index.
>>>>>
>>>>> Cc: Lokesh Vutla <lokeshvutla@ti.com>
>>>>> Cc: Marek Vasut <marex@denx.de>
>>>>> Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
>>>>> ---
>>>>> V1 -> V2: Replace the commit "fix XHCI registers base address".
>>>>> V2 -> V3: Replace the commit "reintroduce the CONFIG_AM57XX symbol"
>>>>>
>>>>>  configs/dra7xx_evm_defconfig    |  1 +
>>>>>  configs/dra7xx_hs_evm_defconfig |  1 +
>>>>>  drivers/usb/host/Kconfig        | 16 ++++++++++++++++
>>>>>  include/linux/usb/xhci-omap.h   |  6 ++++--
>>>>>  4 files changed, 22 insertions(+), 2 deletions(-)
>>>>>
>>>>> diff --git a/configs/dra7xx_evm_defconfig b/configs/dra7xx_evm_defconfig
>>>>> index 26b26cc..1f47f92 100644
>>>
>>> [...]
>>>
>>>>> diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
>>>>> index 5129a57..440fbcf 100644
>>>>> --- a/drivers/usb/host/Kconfig
>>>>> +++ b/drivers/usb/host/Kconfig
>>>>> @@ -43,6 +43,22 @@ config USB_XHCI_ZYNQMP
>>>>>      help
>>>>>        Enables support for the on-chip xHCI controller on Xilinx
>>>>> ZynqMP SoCs.
>>>>>
>>>>> +choice
>>>>> +    prompt "DRA7XX xHCI USB index select"
>>>>> +    depends on DRA7XX
>>>>> +
>>>>> +config USB_XHCI_DRA7XX_INDEX0
>>>>> +    bool "USB0"
>>>>> +    help
>>>>> +      DRA7XX xHCI USB0.
>>>>> +
>>>>> +config USB_XHCI_DRA7XX_INDEX1
>>>>> +    bool "USB1"
>>>>> +    help
>>>>> +      DRA7XX xHCI USB1.
>>>>
>>>> What is this all about ? Shouldn't this come from DT ? And what if I
>>>> want to use both XHCI ? This looks totally bogus ...

Right, both XHCIs cannot be used with current driver and we do not have
the time to fix it by our own... may be TI has?
Remember, you've accepted the driver and following patches, right?

Regarding DT, do we have a DT as a requirement to run USB in U-Boot?
I don't remember this happening and I think it shouldn't be a requirement.

>>>>
>>>
>>> The support for both XHCI is currently missing.
>>> This could be a temporary solution until the DT solution.
>>> The current situation is worse - selecting USB0 or USB1 based on the
>>> target.
>>
>> So we're replacing it with equally bad solution ?

I don't think equally applies here...
This IS an improvement. Of course it is not like you would want it to be,
but still it is from a platform POV.

>> Hmmm , no.
>> The MW will open mid-march, there's about a month to fix this,
>> so please do.
> 
> Do note that the relevant driver here is not yet using DM_USB.

Yes, the driver should be fixed some day. We would really like to take
this task, but unfortunately, we cannot, at least not right now.
But we do need that USB working on our board and not only on TI EVMs...

Tom,
Should we fall back to v1 and have a worse solution for the base addresses?

-- 
Regards,
Igor.

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 837 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170219/be8c5535/attachment.sig>