[U-Boot-Users] U-Boot 1.1.3 does not boot with MPC8349E

[Florian Behrens <flobe01@arcor.de>]

Yep, that's right.

Florian.

Chu hanjin-r52514 <Hanjin.Chu@freescale.com> schrieb am 19.10.2005 09:30:07:

> I am not clear of your DIP setting. Seems you bootup your u-boot 
> from reading HRCW from flash seeing below your log. Anyway, it has bootup.
> 
> Best Regards
> 
> ============================ 
> Neil Chu 
> 
> Developer Technology Organization
> Freescale Semiconductor Inc. 
> Email: hanjin.chu at freescale.com
> ============================ 
> 
> 
> 
> -----Original Message-----
> From: u-boot-users-admin at lists.sourceforge.net [mailto:u-boot-users-
> admin at lists.sourceforge.net]On Behalf Of Florian Behrens
> Sent: Wednesday, October 19, 2005 3:23 PM
> To: McClintock Matthew-R56630
> Cc: u-boot-users at lists.sourceforge.net
> Subject: Re: Re: [U-Boot-Users] U-Boot 1.1.3 does not boot with MPC8349E
> 
> 
> I didn't change the flash address but rather the text segment start 
> address from 0xFE700000 to 0xFE000000 in board/mpc8349ads/config.mk 
> (see also my message from 2005-10-11 08:25).
> 
> I used the commands as described in the README:
> 
> tftp 10000 u-boot.bin
> protect off fe000000 fe09ffff
> erase fe000000 fe09ffff
> cp.b 10000 fe000000 a0000
> 
> Servus,
> Florian.
> 
> Matthew McClintock <msm@freescale.com> schrieb am 19.10.2005 09:00:50:
> 
> > Did you find a solution to your problem? Neil Chu just sent a patch in
> > today that corrects values in the MPC8349 readme. Can you give a listing
> > of the commands you used to program the new u-boot onto your board?
> > 
> > -Matthew
> > 
> > 
> > On Mon, 2005-10-10 at 18:15 +0200, flobe01 at arcor.de wrote:
> > > Has anybody tried to bring up U-Boot 1.1.3 together with a (Power 
> > Quicc II Pro) MPC8349E MDS Processor Board (silicon rev 1.0)? The 
> > board comes with a (probably patched) 1.1.2 version installed. I 
> > want to update it to 1.1.3 in order to be able to use a current 
> > Linux kernel (2.6.13 - U-Boot 1.1.2 seems to be incompatible due to 
> > differences in the bd_info structures, right?).
> > > 
> > > After building U-Boot and writing to the flash according to the 
> > README, the board does show no more signs of life (apart from the 
> > reset sequence leds) after hard reset.
> > > 
> > > I used crosstool 0.38 for building the tool chain with a standard 
> > ppc target (-mcpu=powerpc) and gcc 3.4.1.
> > > 
> > > Are there any board settings necessary other than those defaults 
> > in the Getting Started guide?
> > > 
> > > Thanks and regards,
> > > Florian.

Machen Sie aus 14 Cent spielend bis zu 100 Euro!
Die neue Gaming-Area von Arcor - ?ber 50 Onlinespiele im Angebot.
http://www.arcor.de/rd/emf-gaming-1