From: Kever Yang <kever.yang@rock-chips.com>
To: Jagan Teki <jagan@amarulasolutions.com>,
Philipp Tomsich <philipp.tomsich@vrull.eu>,
Simon Glass <sjg@chromium.org>
Cc: u-boot@lists.denx.de, linux-amarula@amarulasolutions.com,
FUKAUMI Naoki <naoki@radxa.com>,
Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Subject: Re: [PATCH v4 04/12] arm64: dts: rockchip: rk3566: Add Radxa Compute Module 3 IO
Date: Tue, 21 Feb 2023 17:29:09 +0800 [thread overview]
Message-ID: <330a3e72-6dca-b7c2-e123-d9ae7c024f90@rock-chips.com> (raw)
In-Reply-To: <20230217115845.75303-5-jagan@amarulasolutions.com>
On 2023/2/17 19:58, Jagan Teki wrote:
> Radxa Compute Module 3(CM3) IO board an application board from Radxa
> and is compatible with Raspberry Pi CM4 IO form factor.
>
> Specification:
> - 1x HDMI,
> - 2x MIPI DSI
> - 2x MIPI CSI2
> - 1x eDP
> - 1x PCIe card
> - 2x SATA
> - 2x USB 2.0 Host
> - 1x USB 3.0
> - 1x USB 2.0 OTG
> - Phone jack
> - microSD slot
> - 40-pin GPIO expansion header
> - 12V DC
>
> Radxa CM3 needs to mount on top of this IO board in order to create
> complete Radxa CM3 IO board platform.
>
> linux-next commit for the same,
>
> commit <8f19828844f2> ("arm64: dts: rockchip: Fix compatible for Radxa
> CM3")
>
> Add support for Radxa CM3 IO Board.
>
> Co-developed-by: FUKAUMI Naoki <naoki@radxa.com>
> Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
> Co-developed-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
> Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Thanks,
- Kever
> ---
> arch/arm/dts/Makefile | 1 +
> arch/arm/dts/rk3566-radxa-cm3-io.dts | 272 +++++++++++++++++++++++++++
> 2 files changed, 273 insertions(+)
> create mode 100644 arch/arm/dts/rk3566-radxa-cm3-io.dts
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 9d647b9639..037ffc09b1 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -165,6 +165,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3399) += \
> rk3399pro-rock-pi-n10.dtb
>
> dtb-$(CONFIG_ROCKCHIP_RK3568) += \
> + rk3566-radxa-cm3-io.dtb \
> rk3568-evb.dtb
>
> dtb-$(CONFIG_ROCKCHIP_RV1108) += \
> diff --git a/arch/arm/dts/rk3566-radxa-cm3-io.dts b/arch/arm/dts/rk3566-radxa-cm3-io.dts
> new file mode 100644
> index 0000000000..d89d5263cb
> --- /dev/null
> +++ b/arch/arm/dts/rk3566-radxa-cm3-io.dts
> @@ -0,0 +1,272 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2022 Radxa Limited
> + * Copyright (c) 2022 Amarula Solutions(India)
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/soc/rockchip,vop2.h>
> +#include "rk3566.dtsi"
> +#include "rk3566-radxa-cm3.dtsi"
> +
> +/ {
> + model = "Radxa Compute Module 3(CM3) IO Board";
> + compatible = "radxa,cm3-io", "radxa,cm3", "rockchip,rk3566";
> +
> + aliases {
> + mmc1 = &sdmmc0;
> + };
> +
> + chosen: chosen {
> + stdout-path = "serial2:1500000n8";
> + };
> +
> + gmac1_clkin: external-gmac1-clock {
> + compatible = "fixed-clock";
> + clock-frequency = <125000000>;
> + clock-output-names = "gmac1_clkin";
> + #clock-cells = <0>;
> + };
> +
> + hdmi-con {
> + compatible = "hdmi-connector";
> + type = "a";
> +
> + port {
> + hdmi_con_in: endpoint {
> + remote-endpoint = <&hdmi_out_con>;
> + };
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led-1 {
> + gpios = <&gpio4 RK_PA4 GPIO_ACTIVE_LOW>;
> + color = <LED_COLOR_ID_GREEN>;
> + function = LED_FUNCTION_ACTIVITY;
> + linux,default-trigger = "heartbeat";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pi_nled_activity>;
> + };
> + };
> +
> + vcc5v0_usb30: vcc5v0-usb30-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc5v0_usb30";
> + enable-active-high;
> + gpio = <&gpio3 RK_PC2 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vcc5v0_usb30_en_h>;
> + regulator-always-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + vcca1v8_image: vcca1v8-image-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcca1v8_image";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc_1v8_p>;
> + };
> +
> + vdda0v9_image: vdda0v9-image-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcca0v9_image";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> + vin-supply = <&vdda_0v9>;
> + };
> +};
> +
> +&combphy1 {
> + status = "okay";
> +};
> +
> +&gmac1 {
> + assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
> + assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&gmac1_clkin>;
> + assigned-clock-rates = <0>, <125000000>;
> + clock_in_out = "input";
> + phy-handle = <&rgmii_phy1>;
> + phy-mode = "rgmii";
> + pinctrl-names = "default";
> + pinctrl-0 = <&gmac1m0_miim
> + &gmac1m0_tx_bus2
> + &gmac1m0_rx_bus2
> + &gmac1m0_rgmii_clk
> + &gmac1m0_rgmii_bus
> + &gmac1m0_clkinout>;
> + snps,reset-gpio = <&gpio4 RK_PC2 GPIO_ACTIVE_LOW>;
> + snps,reset-active-low;
> + /* Reset time is 20ms, 100ms for rtl8211f */
> + snps,reset-delays-us = <0 20000 100000>;
> + tx_delay = <0x46>;
> + rx_delay = <0x2e>;
> + status = "okay";
> +};
> +
> +&hdmi {
> + avdd-0v9-supply = <&vdda0v9_image>;
> + avdd-1v8-supply = <&vcca1v8_image>;
> + status = "okay";
> +};
> +
> +&hdmi_in {
> + hdmi_in_vp0: endpoint {
> + remote-endpoint = <&vp0_out_hdmi>;
> + };
> +};
> +
> +&hdmi_out {
> + hdmi_out_con: endpoint {
> + remote-endpoint = <&hdmi_con_in>;
> + };
> +};
> +
> +&hdmi_sound {
> + status = "okay";
> +};
> +
> +&mdio1 {
> + rgmii_phy1: ethernet-phy@0 {
> + compatible="ethernet-phy-ieee802.3-c22";
> + reg= <0x0>;
> + };
> +};
> +
> +&pinctrl {
> + gmac1 {
> + gmac1m0_miim: gmac1m0-miim {
> + rockchip,pins =
> + /* gmac1_mdcm0 */
> + <3 RK_PC4 3 &pcfg_pull_none_drv_level_15>,
> + /* gmac1_mdiom0 */
> + <3 RK_PC5 3 &pcfg_pull_none_drv_level_15>;
> + };
> +
> + gmac1m0_rx_bus2: gmac1m0-rx-bus2 {
> + rockchip,pins =
> + /* gmac1_rxd0m0 */
> + <3 RK_PB1 3 &pcfg_pull_none_drv_level_15>,
> + /* gmac1_rxd1m0 */
> + <3 RK_PB2 3 &pcfg_pull_none_drv_level_15>,
> + /* gmac1_rxdvcrsm0 */
> + <3 RK_PB3 3 &pcfg_pull_none_drv_level_15>;
> + };
> +
> + gmac1m0_tx_bus2: gmac1m0-tx-bus2 {
> + rockchip,pins =
> + /* gmac1_txd0m0 */
> + <3 RK_PB5 3 &pcfg_pull_none_drv_level_15>,
> + /* gmac1_txd1m0 */
> + <3 RK_PB6 3 &pcfg_pull_none_drv_level_15>,
> + /* gmac1_txenm0 */
> + <3 RK_PB7 3 &pcfg_pull_none_drv_level_15>;
> + };
> +
> + gmac1m0_rgmii_clk: gmac1m0-rgmii-clk {
> + rockchip,pins =
> + /* gmac1_rxclkm0 */
> + <3 RK_PA7 3 &pcfg_pull_none_drv_level_15>,
> + /* gmac1_txclkm0 */
> + <3 RK_PA6 3 &pcfg_pull_none_drv_level_15>;
> + };
> +
> + gmac1m0_rgmii_bus: gmac1m0-rgmii-bus {
> + rockchip,pins =
> + /* gmac1_rxd2m0 */
> + <3 RK_PA4 3 &pcfg_pull_none_drv_level_15>,
> + /* gmac1_rxd3m0 */
> + <3 RK_PA5 3 &pcfg_pull_none_drv_level_15>,
> + /* gmac1_txd2m0 */
> + <3 RK_PA2 3 &pcfg_pull_none_drv_level_15>,
> + /* gmac1_txd3m0 */
> + <3 RK_PA3 3 &pcfg_pull_none_drv_level_15>;
> + };
> +
> + gmac1m0_clkinout: gmac1m0-clkinout {
> + rockchip,pins =
> + /* gmac1_mclkinoutm0 */
> + <3 RK_PC0 3 &pcfg_pull_none_drv_level_15>;
> + };
> + };
> +
> + leds {
> + pi_nled_activity: pi-nled-activity {
> + rockchip,pins = <4 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + sdcard {
> + sdmmc_pwren: sdmmc-pwren {
> + rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + usb {
> + vcc5v0_usb30_en_h: vcc5v0-host-en-h {
> + rockchip,pins = <3 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&sdmmc0 {
> + bus-width = <4>;
> + cap-mmc-highspeed;
> + cap-sd-highspeed;
> + disable-wp;
> + vqmmc-supply = <&vccio_sd>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det &sdmmc0_pwren>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&usb2phy0_host {
> + phy-supply = <&vcc5v0_usb30>;
> + status = "okay";
> +};
> +
> +&usb2phy1_host {
> + status = "okay";
> +};
> +
> +&usb2phy1_otg {
> + status = "okay";
> +};
> +
> +&usb_host0_ehci {
> + status = "okay";
> +};
> +
> +&usb_host1_xhci {
> + status = "okay";
> +};
> +
> +&vop {
> + assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
> + assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
> + status = "okay";
> +};
> +
> +&vop_mmu {
> + status = "okay";
> +};
> +
> +&vp0 {
> + vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
> + reg = <ROCKCHIP_VOP2_EP_HDMI0>;
> + remote-endpoint = <&hdmi_in_vp0>;
> + };
> +};
next prev parent reply other threads:[~2023-02-21 9:29 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-02-17 11:58 [PATCH v4 00/12] rockchip: Add Radxa CM3 support Jagan Teki
2023-02-17 11:58 ` [PATCH v4 01/12] rockchip: rk3568: Move DM_RESET in arch kconfig Jagan Teki
2023-02-21 9:28 ` Kever Yang
2023-02-17 11:58 ` [PATCH v4 02/12] dt-bindings: rockchip: Sync rockchip, vop2.h from Linux Jagan Teki
2023-02-17 11:58 ` [PATCH v4 03/12] arm64: dts: rockchip: rk3566: Add Radxa Compute Module 3 Jagan Teki
2023-02-17 11:58 ` [PATCH v4 04/12] arm64: dts: rockchip: rk3566: Add Radxa Compute Module 3 IO Jagan Teki
2023-02-21 9:29 ` Kever Yang [this message]
2023-02-17 11:58 ` [PATCH v4 05/12] board: rockchip: Add Radxa Compute Module 3 IO Board Jagan Teki
2023-02-17 11:58 ` [PATCH v4 06/12] phy: rockchip: inno-usb2: Add support #address_cells = 2 Jagan Teki
2023-02-21 9:29 ` Kever Yang
2023-02-17 11:58 ` [PATCH v4 07/12] phy: rockchip-inno-usb2: Add USB2 PHY for rk3568 Jagan Teki
2023-02-21 9:30 ` Kever Yang
2023-02-17 11:58 ` [PATCH v4 08/12] drivers: phy: add naneng combphy " Jagan Teki
2023-02-21 9:31 ` Kever Yang
2023-02-17 11:58 ` [PATCH v4 09/12] arm64: dts: rk356x-u-boot: Drop combphy1 assigned-clocks/rates Jagan Teki
2023-02-21 9:32 ` Kever Yang
2023-02-17 11:58 ` [PATCH v4 10/12] rockchip: rk3568: add rk3568 pinctrl driver Jagan Teki
2023-02-21 9:32 ` Kever Yang
2023-02-17 11:58 ` [PATCH v4 11/12] rockchip: rk3568: Select DM_REGULATOR_FIXED Jagan Teki
2023-02-21 9:33 ` Kever Yang
2023-02-17 11:58 ` [PATCH v4 12/12] rk3566: radxa-cm3: Enable USB2.0, USB3.0 support Jagan Teki
2023-02-21 9:33 ` Kever Yang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=330a3e72-6dca-b7c2-e123-d9ae7c024f90@rock-chips.com \
--to=kever.yang@rock-chips.com \
--cc=abbaraju.manojsai@amarulasolutions.com \
--cc=jagan@amarulasolutions.com \
--cc=linux-amarula@amarulasolutions.com \
--cc=naoki@radxa.com \
--cc=philipp.tomsich@vrull.eu \
--cc=sjg@chromium.org \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox