[U-Boot-Users] [PATCH u-boot-at91] Add support for AT91SAM9263EK

[Jared Holzman <j.holzman@genesysdesign.com.au>]

This patch adds support for the AT91SAM9263EK board. It builds on top of 
the support added for the AT91SAM9260EK by Stelian Pop. It was created 
against the u-boot-at91 custodian tree, so I hope this is correct place 
to submit it.
---

diff --git a/Makefile b/Makefile
index cf16bd6..c6d903e 100644
--- a/Makefile
+++ b/Makefile
@@ -2311,6 +2311,9 @@ at91rm9200dk_config    :    unconfig
 at91sam9260ek_config    :    unconfig
     @$(MKCONFIG) $(@:_config=) arm arm926ejs at91sam9260ek atmel at91sam9
 
+at91sam9263ek_config    :    unconfig
+    @$(MKCONFIG) $(@:_config=) arm arm926ejs at91sam9263ek atmel at91sam9
+
 cmc_pu2_config    :    unconfig
     @$(MKCONFIG) $(@:_config=) arm arm920t cmc_pu2 NULL at91rm9200
 
diff --git a/drivers/net/macb.c b/drivers/net/macb.c
index 703784e..499c7da 100644
--- a/drivers/net/macb.c
+++ b/drivers/net/macb.c
@@ -417,13 +417,13 @@ static int macb_init(struct eth_device *netdev, 
bd_t *bd)
 
     /* choose RMII or MII mode. This depends on the board */
 #ifdef CONFIG_RMII
-#if defined(CONFIG_AT91CAP9) || defined(CONFIG_AT91SAM9260)
+#if defined(CONFIG_AT91CAP9) || defined(CONFIG_AT91SAM9260) || defined 
(CONFIG_AT91SAM9263)
     macb_writel(macb, USRIO, MACB_BIT(RMII) | MACB_BIT(CLKEN));
 #else
     macb_writel(macb, USRIO, 0);
 #endif
 #else
-#if defined(CONFIG_AT91CAP9) || defined(CONFIG_AT91SAM9260)
+#if defined(CONFIG_AT91CAP9) || defined(CONFIG_AT91SAM9260) || defined 
(CONFIG_AT91SAM9263)
     macb_writel(macb, USRIO, MACB_BIT(CLKEN));
 #else
     macb_writel(macb, USRIO, MACB_BIT(MII));
diff --git a/include/asm-arm/arch-at91sam9/hardware.h 
b/include/asm-arm/arch-at91sam9/hardware.h
index 80b334f..4f9f2a8 100644
--- a/include/asm-arm/arch-at91sam9/hardware.h
+++ b/include/asm-arm/arch-at91sam9/hardware.h
@@ -28,6 +28,10 @@
 #include <asm/arch/at91sam9261.h>
 #elif defined(CONFIG_AT91SAM9263)
 #include <asm/arch/at91sam9263.h>
+#define AT91_BASE_EMAC    AT91SAM9263_BASE_EMAC
+#define AT91_BASE_SPI    AT91SAM9263_BASE_SPI0
+#define AT91_ID_UHP    AT91SAM9263_ID_UHP
+#define AT91_PMC_UHP    AT91SAM926x_PMC_UHP
 #elif defined(CONFIG_AT91SAM9RL)
 #include <asm/arch/at91sam9rl.h>
 #elif defined(CONFIG_AT91CAP9)
diff --git a/net/eth.c b/net/eth.c
index 99897ca..f0b9091 100644
--- a/net/eth.c
+++ b/net/eth.c
@@ -284,7 +284,7 @@ int eth_initialize(bd_t *bis)
 #if defined(CONFIG_FSLDMAFEC)
     mcdmafec_initialize(bis);
 #endif
-#if defined(CONFIG_AT91CAP9) || defined(CONFIG_AT91SAM9260)
+#if defined(CONFIG_AT91CAP9) || defined(CONFIG_AT91SAM9260) || 
defined(CONFIG_AT91SAM9263)
     at91sam9_eth_initialize(bis);
 #endif
 
-- 

Regards,

Jared Holzman

------------------------------------------------------------------------

*Electronics Design Engineer*

*Genesys Electronics Design Pty Ltd*

Unit 5, 33 Ryde Rd Pymble
NSW, Australia 2073

Direct: +612 9496 8924
Phone: +612 9496 8900
Fax: +612 9496 8999

j.holzman at genesysdesign.com.au <mailto:j.holzman@genesysdesign.com.au>
www.genesysdesign.com.au <http://www.genesysdesign.com.au>

------------------------------------------------------------------------