* [U-Boot] [PATCH] move README.imx31 to doc/ and merge with README.mx31
@ 2008-09-18 14:58 Jean-Christophe PLAGNIOL-VILLARD
2008-09-18 14:58 ` [U-Boot] [PATCH] update uImgae FIT multi documentation Jean-Christophe PLAGNIOL-VILLARD
2008-09-29 13:38 ` [U-Boot] [PATCH] move README.imx31 to doc/ and merge with README.mx31 Shinya Kuribayashi
0 siblings, 2 replies; 3+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2008-09-18 14:58 UTC (permalink / raw)
To: u-boot
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/README.imx31 b/README.imx31
deleted file mode 100644
index f545f01..0000000
--- a/README.imx31
+++ /dev/null
@@ -1,13 +0,0 @@
-i.MX31 specific Configuration Options:
---------------------------------------
-
-- Timer precision:
- CONFIG_MX31_TIMER_HIGH_PRECISION
-
- Enable higher precision timer. The low-precision timer
- (default) provides approximately 4% error, whereas the
- high-precision timer is about 0.4% accurate. The extra
- accuracy is achieved at the cost of higher computational
- overhead, which, in places where time is measured, should
- not be critical, so, it should be safe to enable this
- option.
diff --git a/doc/README.imx31 b/doc/README.imx31
new file mode 100644
index 0000000..91ef766
--- /dev/null
+++ b/doc/README.imx31
@@ -0,0 +1,29 @@
+U-Boot for Freescale i.MX31
+
+This file contains information for the port of U-Boot to the Freescale
+i.MX31 SoC.
+
+1. CONFIGURATION OPTIONS/SETTINGS
+---------------------------------
+
+1.1 Configuration of MC13783 SPI bus
+------------------------------------
+ The power management companion chip MC13783 is connected to the
+ i.MX31 via an SPI bus. Use the following configuration options
+ to setup the bus and chip select used for a particular board.
+
+ CONFIG_MC13783_SPI_BUS -- defines the SPI bus the MC13783 is connected to.
+ Note that 0 is CSPI1, 1 is CSPI2 and 2 is CSPI3.
+ CONFIG_MC13783_SPI_CS -- define the chip select the MC13783 s connected to.
+
+1.2 Timer precision
+-------------------
+ CONFIG_MX31_TIMER_HIGH_PRECISION
+
+ Enable higher precision timer. The low-precision timer
+ (default) provides approximately 4% error, whereas the
+ high-precision timer is about 0.4% accurate. The extra
+ accuracy is achieved at the cost of higher computational
+ overhead, which, in places where time is measured, should
+ not be critical, so, it should be safe to enable this
+ option.
diff --git a/doc/README.mx31 b/doc/README.mx31
deleted file mode 100644
index 291c2f3..0000000
--- a/doc/README.mx31
+++ /dev/null
@@ -1,17 +0,0 @@
-U-Boot for Freescale i.MX31
-
-This file contains information for the port of U-Boot to the Freescale
-i.MX31 SoC.
-
-1. CONFIGURATION OPTIONS/SETTINGS
----------------------------------
-
-1.1 Configuration of MC13783 SPI bus
-------------------------------------
-The power management companion chip MC13783 is connected to the
-i.MX31 via an SPI bus. Use the following configuration options
-to setup the bus and chip select used for a particular board.
-
-CONFIG_MC13783_SPI_BUS -- defines the SPI bus the MC13783 is connected to.
- Note that 0 is CSPI1, 1 is CSPI2 and 2 is CSPI3.
-CONFIG_MC13783_SPI_CS -- define the chip select the MC13783 s connected to.
--
1.5.6.5
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [U-Boot] [PATCH] update uImgae FIT multi documentation
2008-09-18 14:58 [U-Boot] [PATCH] move README.imx31 to doc/ and merge with README.mx31 Jean-Christophe PLAGNIOL-VILLARD
@ 2008-09-18 14:58 ` Jean-Christophe PLAGNIOL-VILLARD
2008-09-29 13:38 ` [U-Boot] [PATCH] move README.imx31 to doc/ and merge with README.mx31 Shinya Kuribayashi
1 sibling, 0 replies; 3+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2008-09-18 14:58 UTC (permalink / raw)
To: u-boot
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/doc/uImage.FIT/multi.its b/doc/uImage.FIT/multi.its
index b992962..1d8c2db 100644
--- a/doc/uImage.FIT/multi.its
+++ b/doc/uImage.FIT/multi.its
@@ -56,6 +56,7 @@
data = /incbin/("./eldk-4.2-ramdisk");
type = "ramdisk";
arch = "ppc";
+ os = "linux";
compression = "gzip";
hash at 1 {
algo = "sha1";
@@ -67,6 +68,7 @@
data = /incbin/("./eldk-3.1-ramdisk");
type = "ramdisk";
arch = "ppc";
+ os = "linux";
compression = "gzip";
hash at 1 {
algo = "crc32";
--
1.5.6.5
^ permalink raw reply related [flat|nested] 3+ messages in thread* [U-Boot] [PATCH] move README.imx31 to doc/ and merge with README.mx31
2008-09-18 14:58 [U-Boot] [PATCH] move README.imx31 to doc/ and merge with README.mx31 Jean-Christophe PLAGNIOL-VILLARD
2008-09-18 14:58 ` [U-Boot] [PATCH] update uImgae FIT multi documentation Jean-Christophe PLAGNIOL-VILLARD
@ 2008-09-29 13:38 ` Shinya Kuribayashi
1 sibling, 0 replies; 3+ messages in thread
From: Shinya Kuribayashi @ 2008-09-29 13:38 UTC (permalink / raw)
To: u-boot
Ping. Please consider making this into the upcoming release.
Jean-Christophe PLAGNIOL-VILLARD wrote:
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
>
> diff --git a/README.imx31 b/README.imx31
> deleted file mode 100644
> index f545f01..0000000
> --- a/README.imx31
> +++ /dev/null
> @@ -1,13 +0,0 @@
> -i.MX31 specific Configuration Options:
> ---------------------------------------
> -
> -- Timer precision:
> - CONFIG_MX31_TIMER_HIGH_PRECISION
> -
> - Enable higher precision timer. The low-precision timer
> - (default) provides approximately 4% error, whereas the
> - high-precision timer is about 0.4% accurate. The extra
> - accuracy is achieved at the cost of higher computational
> - overhead, which, in places where time is measured, should
> - not be critical, so, it should be safe to enable this
> - option.
> diff --git a/doc/README.imx31 b/doc/README.imx31
> new file mode 100644
> index 0000000..91ef766
> --- /dev/null
> +++ b/doc/README.imx31
> @@ -0,0 +1,29 @@
> +U-Boot for Freescale i.MX31
> +
> +This file contains information for the port of U-Boot to the Freescale
> +i.MX31 SoC.
> +
> +1. CONFIGURATION OPTIONS/SETTINGS
> +---------------------------------
> +
> +1.1 Configuration of MC13783 SPI bus
> +------------------------------------
> + The power management companion chip MC13783 is connected to the
> + i.MX31 via an SPI bus. Use the following configuration options
> + to setup the bus and chip select used for a particular board.
> +
> + CONFIG_MC13783_SPI_BUS -- defines the SPI bus the MC13783 is connected to.
> + Note that 0 is CSPI1, 1 is CSPI2 and 2 is CSPI3.
> + CONFIG_MC13783_SPI_CS -- define the chip select the MC13783 s connected to.
> +
> +1.2 Timer precision
> +-------------------
> + CONFIG_MX31_TIMER_HIGH_PRECISION
> +
> + Enable higher precision timer. The low-precision timer
> + (default) provides approximately 4% error, whereas the
> + high-precision timer is about 0.4% accurate. The extra
> + accuracy is achieved at the cost of higher computational
> + overhead, which, in places where time is measured, should
> + not be critical, so, it should be safe to enable this
> + option.
> diff --git a/doc/README.mx31 b/doc/README.mx31
> deleted file mode 100644
> index 291c2f3..0000000
> --- a/doc/README.mx31
> +++ /dev/null
> @@ -1,17 +0,0 @@
> -U-Boot for Freescale i.MX31
> -
> -This file contains information for the port of U-Boot to the Freescale
> -i.MX31 SoC.
> -
> -1. CONFIGURATION OPTIONS/SETTINGS
> ----------------------------------
> -
> -1.1 Configuration of MC13783 SPI bus
> -------------------------------------
> -The power management companion chip MC13783 is connected to the
> -i.MX31 via an SPI bus. Use the following configuration options
> -to setup the bus and chip select used for a particular board.
> -
> -CONFIG_MC13783_SPI_BUS -- defines the SPI bus the MC13783 is connected to.
> - Note that 0 is CSPI1, 1 is CSPI2 and 2 is CSPI3.
> -CONFIG_MC13783_SPI_CS -- define the chip select the MC13783 s connected to.
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2008-09-29 13:38 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-09-18 14:58 [U-Boot] [PATCH] move README.imx31 to doc/ and merge with README.mx31 Jean-Christophe PLAGNIOL-VILLARD
2008-09-18 14:58 ` [U-Boot] [PATCH] update uImgae FIT multi documentation Jean-Christophe PLAGNIOL-VILLARD
2008-09-29 13:38 ` [U-Boot] [PATCH] move README.imx31 to doc/ and merge with README.mx31 Shinya Kuribayashi
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox