From: Heiko Schocher <hs@denx.de>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH v2 05/16] soft_i2c: prevent compilerwarnings if driver not uses CPU Pins.
Date: Wed, 15 Oct 2008 09:35:26 +0200 [thread overview]
Message-ID: <48F59D3E.1070803@denx.de> (raw)
This patch fixes the following warnings, when using
the soft_i2c driver using no CPU pins on MPC82xx or MPC8xx
systems:
soft_i2c.c: In function 'send_reset':
soft_i2c.c:93: warning: unused variable 'immr'
soft_i2c.c: In function 'send_start':
soft_i2c.c:124: warning: unused variable 'immr'
soft_i2c.c: In function 'send_stop':
soft_i2c.c:146: warning: unused variable 'immr'
soft_i2c.c: In function 'send_ack':
soft_i2c.c:171: warning: unused variable 'immr'
soft_i2c.c: In function 'write_byte':
soft_i2c.c:196: warning: unused variable 'immr'
soft_i2c.c: In function 'read_byte':
soft_i2c.c:244: warning: unused variable 'immr'
Signed-off-by: Heiko Schocher <hs@denx.de>
---
drivers/i2c/soft_i2c.c | 43 ++++++-------------------------------------
include/i2c.h | 9 +++++++++
2 files changed, 15 insertions(+), 37 deletions(-)
diff --git a/drivers/i2c/soft_i2c.c b/drivers/i2c/soft_i2c.c
index 57736da..19c364b 100644
--- a/drivers/i2c/soft_i2c.c
+++ b/drivers/i2c/soft_i2c.c
@@ -82,7 +82,6 @@ static void send_ack (int);
static int write_byte (uchar byte);
static uchar read_byte (int);
-
/*-----------------------------------------------------------------------
* Send a reset sequence consisting of 9 clocks with the data signal high
* to clock any confused device back into an idle state. Also send a
@@ -90,12 +89,7 @@ static uchar read_byte (int);
*/
static void send_reset(void)
{
-#ifdef CONFIG_MPC8260
- volatile ioport_t *iop = ioport_addr((immap_t *)CFG_IMMR, I2C_PORT);
-#endif
-#ifdef CONFIG_8xx
- volatile immap_t *immr = (immap_t *)CFG_IMMR;
-#endif
+ I2C_SOFT_DECLARATIONS /* intentional without ';' */
int j;
I2C_SCL(1);
@@ -121,12 +115,7 @@ static void send_reset(void)
*/
static void send_start(void)
{
-#ifdef CONFIG_MPC8260
- volatile ioport_t *iop = ioport_addr((immap_t *)CFG_IMMR, I2C_PORT);
-#endif
-#ifdef CONFIG_8xx
- volatile immap_t *immr = (immap_t *)CFG_IMMR;
-#endif
+ I2C_SOFT_DECLARATIONS /* intentional without ';' */
I2C_DELAY;
I2C_SDA(1);
@@ -143,12 +132,7 @@ static void send_start(void)
*/
static void send_stop(void)
{
-#ifdef CONFIG_MPC8260
- volatile ioport_t *iop = ioport_addr((immap_t *)CFG_IMMR, I2C_PORT);
-#endif
-#ifdef CONFIG_8xx
- volatile immap_t *immr = (immap_t *)CFG_IMMR;
-#endif
+ I2C_SOFT_DECLARATIONS /* intentional without ';' */
I2C_SCL(0);
I2C_DELAY;
@@ -168,12 +152,7 @@ static void send_stop(void)
*/
static void send_ack(int ack)
{
-#ifdef CONFIG_MPC8260
- volatile ioport_t *iop = ioport_addr((immap_t *)CFG_IMMR, I2C_PORT);
-#endif
-#ifdef CONFIG_8xx
- volatile immap_t *immr = (immap_t *)CFG_IMMR;
-#endif
+ I2C_SOFT_DECLARATIONS /* intentional without ';' */
I2C_SCL(0);
I2C_DELAY;
@@ -193,12 +172,7 @@ static void send_ack(int ack)
*/
static int write_byte(uchar data)
{
-#ifdef CONFIG_MPC8260
- volatile ioport_t *iop = ioport_addr((immap_t *)CFG_IMMR, I2C_PORT);
-#endif
-#ifdef CONFIG_8xx
- volatile immap_t *immr = (immap_t *)CFG_IMMR;
-#endif
+ I2C_SOFT_DECLARATIONS /* intentional without ';' */
int j;
int nack;
@@ -273,12 +247,7 @@ int i2c_set_bus_speed(unsigned int speed)
*/
static uchar read_byte(int ack)
{
-#ifdef CONFIG_MPC8260
- volatile ioport_t *iop = ioport_addr((immap_t *)CFG_IMMR, I2C_PORT);
-#endif
-#ifdef CONFIG_8xx
- volatile immap_t *immr = (immap_t *)CFG_IMMR;
-#endif
+ I2C_SOFT_DECLARATIONS /* intentional without ';' */
int data;
int j;
diff --git a/include/i2c.h b/include/i2c.h
index a51c164..a6e797a 100644
--- a/include/i2c.h
+++ b/include/i2c.h
@@ -67,6 +67,15 @@
#define CFG_SPD_BUS_NUM 0
#endif
+#ifndef I2C_SOFT_DECLARATIONS
+# if defined(CONFIG_MPC8260)
+# define I2C_SOFT_DECLARATIONS volatile ioport_t *iop = ioport_addr((immap_t *)CFG_IMMR, I2C_PORT);
+# elif defined(CONFIG_8xx)
+# define I2C_SOFT_DECLARATIONS volatile immap_t *immr = (immap_t *)CFG_IMMR;
+# else
+# define I2C_SOFT_DECLARATIONS
+# endif
+#endif
/*
* Initialization, must be called once on start up, may be called
* repeatedly to change the speed and slave addresses.
--
1.5.6.1
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
next reply other threads:[~2008-10-15 7:35 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-10-15 7:35 Heiko Schocher [this message]
2008-10-15 16:35 ` [U-Boot] [PATCH v2 05/16] soft_i2c: prevent compilerwarnings if driver not uses CPU Pins Ben Warren
2008-10-15 18:42 ` Wolfgang Denk
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=48F59D3E.1070803@denx.de \
--to=hs@denx.de \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox