[U-Boot] [PATCH] drivers/qe/uec_phy.c: Added PHY-less (fixed PHY) driver.

[Richard Retanubun <RichardRetanubun@RuggedCom.com>]

Copied over the fixed PHY driver as used in pp4xx/4xx_enet.c.
This adds support for PHY-less MAC connections to the UEC.

Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
---
Documentation change only:
Same patch as before, now with a board configuration file example that
actually applies to UEC based boards :)

 drivers/qe/uec_phy.c |   78 ++++++++++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 78 insertions(+), 0 deletions(-)

diff --git a/drivers/qe/uec_phy.c b/drivers/qe/uec_phy.c
index 2243d3b..b64748b 100644
--- a/drivers/qe/uec_phy.c
+++ b/drivers/qe/uec_phy.c
@@ -44,6 +44,53 @@
 #define ugphy_vdbg(ugeth, fmt, args...) do { } while (0)
 #endif /* UEC_VERBOSE_DEBUG */
 
+/*--------------------------------------------------------------------+
+ * Fixed PHY (PHY-less) support for Ethernet Ports.
+ *
+ * Adapted from cpu/ppc4xx/4xx_enet.c
+ *--------------------------------------------------------------------*/
+
+/*
+ * Some boards do not have a PHY for each ethernet port. These ports
+ * are known as Fixed PHY (or PHY-less) ports. For such ports,
+ * define CONFIG_SYS_FIXED_PHY_PORTS to define what the speed and
+ * duplex should be for these ports in the board configuration file.
+ *
+ * Example board configuration file:
+ *
+ *	#define CONFIG_FIXED_PHY   0xFFFFFFFF
+ *
+ *	#define CONFIG_SYS_UEC1_PHY_ADDR 0 <- PHY-less port
+ *	#define CONFIG_SYS_UEC2_PHY_ADDR 1
+ *	#define CONFIG_SYS_UEC3_PHY_ADDR 2 <- PHY-less port
+ *	#define CONFIG_SYS_UEC4_PHY_ADDR 3
+ *
+ *	#define CONFIG_SYS_FIXED_PHY_PORT(devnum,speed,duplex) \
+ *		{devnum, speed, duplex},
+ *
+ *	#define CONFIG_SYS_FIXED_PHY_PORTS \
+ *		CONFIG_SYS_FIXED_PHY_PORT(0, SPEED_1000, DUPLEX_FULL) \
+ *		CONFIG_SYS_FIXED_PHY_PORT(2, SPEED_100, DUPLEX_HALF)
+ */
+
+#ifndef CONFIG_FIXED_PHY
+#define CONFIG_FIXED_PHY	0xFFFFFFFF /* Fixed PHY (PHY-less) */
+#endif
+
+#ifndef CONFIG_SYS_FIXED_PHY_PORTS
+#define CONFIG_SYS_FIXED_PHY_PORTS	/* default is an empty array */
+#endif
+
+struct fixed_phy_port {
+	unsigned int devnum;	/* ethernet port */
+	unsigned int speed;	/* specified speed 10,100 or 1000 */
+	unsigned int duplex;	/* specified duplex FULL or HALF */
+};
+
+static const struct fixed_phy_port fixed_phy_port[] = {
+	CONFIG_SYS_FIXED_PHY_PORTS /* defined in board configuration file */
+};
+
 static void config_genmii_advert (struct uec_mii_info *mii_info);
 static void genmii_setup_forced (struct uec_mii_info *mii_info);
 static void genmii_restart_aneg (struct uec_mii_info *mii_info);
@@ -533,6 +580,28 @@ static void dm9161_close (struct uec_mii_info *mii_info)
 {
 }
 
+static int fixed_phy_aneg (struct uec_mii_info *mii_info)
+{
+	mii_info->autoneg = 0; /* Turn off auto negotiation for fixed phy */
+	return 0;
+}
+
+static int fixed_phy_read_status (struct uec_mii_info *mii_info)
+{
+	int i = 0;
+
+	for (i = 0; i < ARRAY_SIZE(fixed_phy_port); i++) {
+		if (mii_info->mii_id == fixed_phy_port[i].devnum) {
+			mii_info->speed = fixed_phy_port[i].speed;
+			mii_info->duplex = fixed_phy_port[i].duplex;
+			mii_info->link = 1; /* Link is always UP */
+			mii_info->pause = 0;
+			break;
+		}
+	}
+	return 0;
+}
+
 static struct phy_info phy_info_dm9161 = {
 	.phy_id = 0x0181b880,
 	.phy_id_mask = 0x0ffffff0,
@@ -577,6 +646,14 @@ static struct phy_info phy_info_bcm5481 = {
 	.init = bcm_init,
 };
 
+static struct phy_info phy_info_fixedphy = {
+	.phy_id = CONFIG_FIXED_PHY,
+	.phy_id_mask = CONFIG_FIXED_PHY,
+	.name = "Fixed PHY",
+	.config_aneg = fixed_phy_aneg,
+	.read_status = fixed_phy_read_status,
+};
+
 static struct phy_info phy_info_genmii = {
 	.phy_id = 0x00000000,
 	.phy_id_mask = 0x00000000,
@@ -591,6 +668,7 @@ static struct phy_info *phy_info[] = {
 	&phy_info_dm9161a,
 	&phy_info_marvell,
 	&phy_info_bcm5481,
+	&phy_info_fixedphy,
 	&phy_info_genmii,
 	NULL
 };
-- 
1.5.5.GIT