[U-Boot] [PATCH 19/31] i2c, mpc83xx: add CONFIG_SYS_I2C_INIT_BOARD for fsl_i2c

[Heiko Schocher <hs@denx.de>]

This patch adds the possibility to call a board specific
i2c bus reset routine for the fsl_i2c bus driver, and adds
this option for the keymile kmeter1 board.

Signed-off-by: Heiko Schocher <hs@denx.de>
---
 board/keymile/common/common.c |   14 ++++++++++++++
 drivers/i2c/fsl_i2c.c         |    6 ++++++
 include/configs/kmeter1.h     |    1 +
 3 files changed, 21 insertions(+), 0 deletions(-)

diff --git a/board/keymile/common/common.c b/board/keymile/common/common.c
index 17312b5..a282421 100644
--- a/board/keymile/common/common.c
+++ b/board/keymile/common/common.c
@@ -421,6 +421,7 @@ static int get_scl (void)

 #endif

+#if !defined(CONFIG_KMETER1)
 static void writeStartSeq (void)
 {
 	set_sda (1);
@@ -471,6 +472,7 @@ static int i2c_make_abort (void)
 	get_sda ();
 	return ret;
 }
+#endif

 /**
  * i2c_init_board - reset i2c bus. When the board is powercycled during a
@@ -478,6 +480,17 @@ static int i2c_make_abort (void)
  */
 void i2c_init_board(void)
 {
+#if defined(CONFIG_KMETER1)
+	struct fsl_i2c *dev;
+	dev = (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C_OFFSET);
+	uchar	dummy;
+
+	out_8 (&dev->cr, (I2C_CR_MSTA));
+	out_8 (&dev->cr, (I2C_CR_MEN | I2C_CR_MSTA));
+	dummy = in_8(&dev->dr);
+	out_8 (&dev->cr, (I2C_CR_MEN));
+
+#else
 #if defined(CONFIG_HARD_I2C)
 	volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR ;
 	volatile i2c8260_t *i2c	= (i2c8260_t *)&immap->im_i2c;
@@ -497,6 +510,7 @@ void i2c_init_board(void)
 	/* Set the PortPins back to use for I2C */
 	setports (0);
 #endif
+#endif
 }
 #endif
 #endif
diff --git a/drivers/i2c/fsl_i2c.c b/drivers/i2c/fsl_i2c.c
index 5242884..7ba5ab1 100644
--- a/drivers/i2c/fsl_i2c.c
+++ b/drivers/i2c/fsl_i2c.c
@@ -176,6 +176,12 @@ i2c_init(int speed, int slaveadd)
 	struct fsl_i2c *dev;
 	unsigned int temp;

+#ifdef CONFIG_SYS_I2C_INIT_BOARD
+	/* call board specific i2c bus reset routine before accessing the   */
+	/* environment, which might be in a chip on that bus. For details   */
+	/* about this problem see doc/I2C_Edge_Conditions.                  */
+	i2c_init_board();
+#endif
 	dev = (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C_OFFSET);

 	writeb(0, &dev->cr);			/* stop I2C controller */
diff --git a/include/configs/kmeter1.h b/include/configs/kmeter1.h
index 17ddcec..31e5cd6 100644
--- a/include/configs/kmeter1.h
+++ b/include/configs/kmeter1.h
@@ -316,6 +316,7 @@
 #define CONFIG_SYS_I2C_OFFSET	0x3000

 #define CONFIG_SYS_MAX_I2C_BUS		2
+#define CONFIG_SYS_I2C_INIT_BOARD	1
 #define CONFIG_I2C_MUX		1

 /* EEprom support */
-- 
1.6.0.6

-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany