[U-Boot] [PATCH 1/1] net: Add Xilinx LL Temac driver version2

[Michal Simek <monstr@monstr.eu>]

Hi Ben,

> Hi Michal,
> 
> You submitted this so long ago that this driver should be in the tree
> right now.  Unfortunately, I didn't give a thorough enough review the
> first time and I think it would be wrong to pull it in right now without
> addressing some more things.  If you take care of this, I promise to put
> it in the front of the queue for the next release:
> 
> monstr at monstr.eu wrote:
>> From: Michal Simek <monstr@monstr.eu>
>>
>> ---
>>   
> This '---' line ensures that nothing below it (including your SOB) goes
> in the commit.  Please remove it, add a meaningful commit message and
> move the next few lines below the next '---' line.  Also, the "version
> 2" in the title should be in square brackets so it get stripped from the
> commit title.
>> v2: Coding style cleanup, use debug() instead of printf
>> in debug messages
>>
>> v1: Initial version
>>
>> Signed-off-by: Michal Simek <monstr@monstr.eu>
>> ---
>>  drivers/net/Makefile          |    1 +
>>  drivers/net/xilinx_ll_temac.c |  540
>> +++++++++++++++++++++++++++++++++++++++++
>>  2 files changed, 541 insertions(+), 0 deletions(-)
>>  create mode 100644 drivers/net/xilinx_ll_temac.c
>>
>> diff --git a/drivers/net/Makefile b/drivers/net/Makefile
>> index 631336a..1e80698 100644
>> --- a/drivers/net/Makefile
>> +++ b/drivers/net/Makefile
>> @@ -68,6 +68,7 @@ COBJS-$(CONFIG_ULI526X) += uli526x.o
>>  COBJS-$(CONFIG_VSC7385_ENET) += vsc7385.o
>>  COBJS-$(CONFIG_XILINX_EMAC) += xilinx_emac.o
>>  COBJS-$(CONFIG_XILINX_EMACLITE) += xilinx_emaclite.o
>> +COBJS-$(CONFIG_XILINX_LL_TEMAC) += xilinx_ll_temac.o
>>  COBJS-$(CONFIG_SH_ETHER) += sh_eth.o
>>  
>>   
> This doesn't apply any more.  Not your fault :)
> 
> 
> I get the following whitespace errors:
> 
> Applying net: Add Xilinx LL Temac driver
> .dotest/patch:415: trailing whitespace.
>   .dotest/patch:419: trailing whitespace.
>   .dotest/patch:424: trailing whitespace.

yes, There were three tabs.

> 
> All of the above mentioned issues are ones that I could easily deal
> with, but one thing that really does need to change is that you need to
> use the CONFIG_NET_MULTI API.  In other words, your driver should have a
> single initialize() function (prototyped in include/netdev.h), and an
> eth_device struct that gets registered.  All your access functions
> (eth_init, eth_send, eth_recv etc.) will be static and pointed to by the
> eth_device struct.  Most drivers are already this way.

I look at it and I did some change and the main problem is in Microblaze GCC.
We use GCC 3.4.1 and CONFIG_NET_MULTI use weak function and board_eth_init is
never called. We are working on GCC 4.1.2 but I don't know when I get it.

I have two more Xilinx eth drivers in U-BOOT and I think that will be the best
to do all changes together. What do you think?

Thanks,
Michal

> 
> Other than that, it's fine.  Sorry again for taking so very long.
> 
> regards,
> Ben


-- 
Michal Simek, Ing. (M.Eng)
w: www.monstr.eu p: +42-0-721842854