* [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support
2009-07-16 15:28 ` [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support Prafulla Wadaskar
@ 2009-07-16 14:45 ` Dieter Kiermaier
2009-07-16 15:45 ` Prafulla Wadaskar
2009-07-16 15:28 ` [U-Boot] [PATCH 6/6] Marvell RD6281A Board support Prafulla Wadaskar
` (2 subsequent siblings)
3 siblings, 1 reply; 33+ messages in thread
From: Dieter Kiermaier @ 2009-07-16 14:45 UTC (permalink / raw)
To: u-boot
Hi Prafulla, hi Marvell engineers,
> By default Auto Negotiation is enabled for interface speed
> but on some platforms like RD6281A it does not work.
> If you want to forced program it to desired speed,
> this patch helps-
do you have some information why auto negotiation doesn't work on RD6281A?
I'm working on custom hardware and don't want to do the same mistake :)
Many thanks,
Dieter
>
> Through this patch Auto negotiation can be disabled and
> desired interface speed can be configured
>
> This patch is tested on RD6281A Kirkwood board
>
> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
> ---
> drivers/net/kirkwood_egiga.c | 24 ++++++++++++++++++++++++
> 1 files changed, 24 insertions(+), 0 deletions(-)
>
> diff --git a/drivers/net/kirkwood_egiga.c b/drivers/net/kirkwood_egiga.c
> index 3c5db19..1dfd567 100644
> --- a/drivers/net/kirkwood_egiga.c
> +++ b/drivers/net/kirkwood_egiga.c
> @@ -415,7 +415,31 @@ static int kwgbe_init(struct eth_device *dev)
> /* Assign port configuration and command. */
> KWGBEREG_WR(regs->pxc, PRT_CFG_VAL);
> KWGBEREG_WR(regs->pxcx, PORT_CFG_EXTEND_VALUE);
> + /*
> + * Forced 10/100/1000BASE-T interface speed configuration
> + * By default Auto Negotiation of interface speed is enabled
> + * This can be forced disabled and desired speed can be configured
> + */
> +#ifdef CONFIG_DIS_AUTO_NEG_SPEED_GMII
> +#if (!defined (CONFIG_PHY_SPEED) || (CONFIG_PHY_SPEED == _1000BASET))
> + KWGBEREG_WR(regs->psc0, PORT_SERIAL_CONTROL_VALUE
> + | KWGBE_DIS_AUTO_NEG_SPEED_GMII
> + | KWGBE_SET_GMII_SPEED_TO_1000);
> +#elif (CONFIG_PHY_SPEED == _100BASET)
> + KWGBEREG_WR(regs->psc0, PORT_SERIAL_CONTROL_VALUE
> + | KWGBE_DIS_AUTO_NEG_SPEED_GMII
> + | KWGBE_SET_GMII_SPEED_TO_10_100
> + | KWGBE_SET_MII_SPEED_TO_100);
> +#elif (CONFIG_PHY_SPEED == _10BASET)
> + KWGBEREG_WR(regs->psc0, PORT_SERIAL_CONTROL_VALUE
> + | KWGBE_DIS_AUTO_NEG_SPEED_GMII
> + | KWGBE_SET_GMII_SPEED_TO_10_100
> + | KWGBE_SET_MII_SPEED_TO_10);
> +#endif /* CONFIG_PHY_SPEED == _10BASET */
> +#else
> KWGBEREG_WR(regs->psc0, PORT_SERIAL_CONTROL_VALUE);
> +#endif /* CONFIG_DIS_AUTO_NEG_SPEED_GMII */
> +
> /* Disable port initially */
> KWGBEREG_BITS_SET(regs->psc0, KWGBE_SERIAL_PORT_EN);
>
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 1/6] include/config_cmd_default.h cleanup
@ 2009-07-16 15:27 Prafulla Wadaskar
2009-07-16 15:28 ` [U-Boot] [PATCH v7 2/6] Marvell Sheevaplug Board support Prafulla Wadaskar
2009-07-17 21:26 ` [U-Boot] [PATCH 1/6] include/config_cmd_default.h cleanup Wolfgang Denk
0 siblings, 2 replies; 33+ messages in thread
From: Prafulla Wadaskar @ 2009-07-16 15:27 UTC (permalink / raw)
To: u-boot
arranged configurations in alphabetical order
CONFIG_CMD_FLASH moved under ifndef CONFIG_SYS_NO_FLASH
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
---
include/config_cmd_default.h | 6 +++---
1 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/include/config_cmd_default.h b/include/config_cmd_default.h
index 0376e44..a5d87a6 100644
--- a/include/config_cmd_default.h
+++ b/include/config_cmd_default.h
@@ -20,14 +20,13 @@
#define CONFIG_CMD_BOOTD /* bootd */
#define CONFIG_CMD_CONSOLE /* coninfo */
#define CONFIG_CMD_ECHO /* echo arguments */
-#define CONFIG_CMD_SAVEENV /* saveenv */
-#define CONFIG_CMD_FLASH /* flinfo, erase, protect */
#define CONFIG_CMD_FPGA /* FPGA configuration Support */
#define CONFIG_CMD_IMI /* iminfo */
+#define CONFIG_CMD_ITEST /* Integer (and string) test */
#ifndef CONFIG_SYS_NO_FLASH
+#define CONFIG_CMD_FLASH /* flinfo, erase, protect */
#define CONFIG_CMD_IMLS /* List all found images */
#endif
-#define CONFIG_CMD_ITEST /* Integer (and string) test */
#define CONFIG_CMD_LOADB /* loadb */
#define CONFIG_CMD_LOADS /* loads */
#define CONFIG_CMD_MEMORY /* md mm nm mw cp cmp crc base loop mtest */
@@ -35,6 +34,7 @@
#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
#define CONFIG_CMD_NFS /* NFS support */
#define CONFIG_CMD_RUN /* run command in env variable */
+#define CONFIG_CMD_SAVEENV /* saveenv */
#define CONFIG_CMD_SETGETDCR /* DCR support on 4xx */
#define CONFIG_CMD_SOURCE /* "source" command support */
#define CONFIG_CMD_XIMG /* Load part of Multi Image */
--
1.5.3.3
^ permalink raw reply related [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v7 2/6] Marvell Sheevaplug Board support
2009-07-16 15:27 [U-Boot] [PATCH 1/6] include/config_cmd_default.h cleanup Prafulla Wadaskar
@ 2009-07-16 15:28 ` Prafulla Wadaskar
2009-07-16 15:28 ` [U-Boot] [PATCH v13 3/6] Marvell MV88F6281GTW_GE " Prafulla Wadaskar
` (2 more replies)
2009-07-17 21:26 ` [U-Boot] [PATCH 1/6] include/config_cmd_default.h cleanup Wolfgang Denk
1 sibling, 3 replies; 33+ messages in thread
From: Prafulla Wadaskar @ 2009-07-16 15:28 UTC (permalink / raw)
To: u-boot
Reference:
http://plugcomputer.org/
http://openplug.org/plugwiki/index.php/Das_U-boot_plug_support
This patch is tested for-
1. Boot from DRAM/NAND flash
2. File transfer using tftp
3. NAND flash read/write/erase
4. Linux kernel and RFS Boot from NAND
5. Enabled USB PHY init for kernel need
6. Boot from USB supported
Note: to boot Kirkwood kernel with USB support,
you should add "usb start" in the boot sequence
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
---
Change log:
v2: updated as per feedback for v1
v3: updated as per feedback for v2
v4: removed PHY driver dependency, coded in sheevaplug.c
v5: USB support added
v6: config_cmd_default.h used in board config
v7: sheevaplug.h alligned as per cleanup in config_cmd_default.h
MAINTAINERS | 4 +
MAKEALL | 1 +
Makefile | 4 +-
board/Marvell/sheevaplug/Makefile | 51 +++++++++
board/Marvell/sheevaplug/config.mk | 25 ++++
board/Marvell/sheevaplug/sheevaplug.c | 155 ++++++++++++++++++++++++++
board/Marvell/sheevaplug/sheevaplug.h | 41 +++++++
include/configs/sheevaplug.h | 195 +++++++++++++++++++++++++++++++++
8 files changed, 475 insertions(+), 1 deletions(-)
create mode 100644 board/Marvell/sheevaplug/Makefile
create mode 100644 board/Marvell/sheevaplug/config.mk
create mode 100644 board/Marvell/sheevaplug/sheevaplug.c
create mode 100644 board/Marvell/sheevaplug/sheevaplug.h
create mode 100644 include/configs/sheevaplug.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 705bac5..2f3b63c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -673,6 +673,10 @@ Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
SFFSDR ARM926EJS
+Prafulla Wadaskar <prafulla@marvell.com>
+
+ sheevaplug ARM926EJS (Kirkwood SoC)
+
Richard Woodruff <r-woodruff2@ti.com>
omap2420h4 ARM1136EJS
diff --git a/MAKEALL b/MAKEALL
index 41f1445..e987d4a 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -522,6 +522,7 @@ LIST_ARM9=" \
omap730p2 \
sbc2410x \
scb9328 \
+ sheevaplug \
smdk2400 \
smdk2410 \
trab \
diff --git a/Makefile b/Makefile
index d427760..a66c4c7 100644
--- a/Makefile
+++ b/Makefile
@@ -2924,6 +2924,9 @@ sbc2410x_config: unconfig
scb9328_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm920t scb9328 NULL imx
+sheevaplug_config: unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
+
smdk2400_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm920t smdk2400 samsung s3c24x0
@@ -3168,7 +3171,6 @@ omap2420h4_config : unconfig
qong_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm1136 qong davedenx mx31
-
#########################################################################
## ARM1176 Systems
#########################################################################
diff --git a/board/Marvell/sheevaplug/Makefile b/board/Marvell/sheevaplug/Makefile
new file mode 100644
index 0000000..e378b5b
--- /dev/null
+++ b/board/Marvell/sheevaplug/Makefile
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := sheevaplug.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/Marvell/sheevaplug/config.mk b/board/Marvell/sheevaplug/config.mk
new file mode 100644
index 0000000..a4ea769
--- /dev/null
+++ b/board/Marvell/sheevaplug/config.mk
@@ -0,0 +1,25 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+TEXT_BASE = 0x00600000
diff --git a/board/Marvell/sheevaplug/sheevaplug.c b/board/Marvell/sheevaplug/sheevaplug.c
new file mode 100644
index 0000000..547126a
--- /dev/null
+++ b/board/Marvell/sheevaplug/sheevaplug.c
@@ -0,0 +1,155 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "sheevaplug.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ kw_config_gpio(SHEEVAPLUG_OE_VAL_LOW,
+ SHEEVAPLUG_OE_VAL_HIGH,
+ SHEEVAPLUG_OE_LOW, SHEEVAPLUG_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ u32 kwmpp_config[] = {
+ MPP0_NF_IO2,
+ MPP1_NF_IO3,
+ MPP2_NF_IO4,
+ MPP3_NF_IO5,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP7_GPO,
+ MPP8_UART0_RTS,
+ MPP9_UART0_CTS,
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP12_SD_CLK,
+ MPP13_SD_CMD,
+ MPP14_SD_D0,
+ MPP15_SD_D1,
+ MPP16_SD_D2,
+ MPP17_SD_D3,
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_GPIO,
+ MPP21_GPIO,
+ MPP22_GPIO,
+ MPP23_GPIO,
+ MPP24_GPIO,
+ MPP25_GPIO,
+ MPP26_GPIO,
+ MPP27_GPIO,
+ MPP28_GPIO,
+ MPP29_TSMP9,
+ MPP30_GPIO,
+ MPP31_GPIO,
+ MPP32_GPIO,
+ MPP33_GPIO,
+ MPP34_GPIO,
+ MPP35_GPIO,
+ MPP36_GPIO,
+ MPP37_GPIO,
+ MPP38_GPIO,
+ MPP39_GPIO,
+ MPP40_GPIO,
+ MPP41_GPIO,
+ MPP42_GPIO,
+ MPP43_GPIO,
+ MPP44_GPIO,
+ MPP45_GPIO,
+ MPP46_GPIO,
+ MPP47_GPIO,
+ MPP48_GPIO,
+ MPP49_GPIO,
+ 0
+ };
+ kirkwood_mpp_conf(kwmpp_config);
+
+ /*
+ * arch number of board
+ */
+ gd->bd->bi_arch_number = MACH_TYPE_SHEEVAPLUG;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ int i;
+
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ gd->bd->bi_dram[i].start = kw_sdram_bar(i);
+ gd->bd->bi_dram[i].size = kw_sdram_bs(i);
+ }
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and enable MV88E1116 PHY */
+void reset_phy(void)
+{
+ u16 reg;
+ u16 devadr;
+ char *name = "egiga0";
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ /* command to read PHY dev address */
+ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+ printf("Err..%s could not read PHY dev address\n",
+ __FUNCTION__);
+ return;
+ }
+
+ /*
+ * Enable RGMII delay on Tx and Rx for CPU port
+ * Ref: sec 4.7.2 of chip datasheet
+ */
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
+ miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
+ reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+ miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
+
+ /* reset the phy */
+ miiphy_reset(name, devadr);
+
+ printf("88E1116 Initialized on %s\n", name);
+}
+#endif /* CONFIG_RESET_PHY_R */
diff --git a/board/Marvell/sheevaplug/sheevaplug.h b/board/Marvell/sheevaplug/sheevaplug.h
new file mode 100644
index 0000000..3ed5b7f
--- /dev/null
+++ b/board/Marvell/sheevaplug/sheevaplug.h
@@ -0,0 +1,41 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __SHEEVAPLUG_H
+#define __SHEEVAPLUG_H
+
+#define SHEEVAPLUG_OE_LOW (~(0))
+#define SHEEVAPLUG_OE_HIGH (~(0))
+#define SHEEVAPLUG_OE_VAL_LOW (1 << 29) /* USB_PWEN low */
+#define SHEEVAPLUG_OE_VAL_HIGH (1 << 17) /* LED pin high */
+
+/* PHY related */
+#define MV88E1116_LED_FCTRL_REG 10
+#define MV88E1116_CPRSP_CR3_REG 21
+#define MV88E1116_MAC_CTRL_REG 21
+#define MV88E1116_PGADR_REG 22
+#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
+
+#endif /* __SHEEVAPLUG_H */
diff --git a/include/configs/sheevaplug.h b/include/configs/sheevaplug.h
new file mode 100644
index 0000000..fc401a8
--- /dev/null
+++ b/include/configs/sheevaplug.h
@@ -0,0 +1,195 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_SHEEVAPLUG_H
+#define _CONFIG_SHEEVAPLUG_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING "\nMarvell-Sheevaplug"
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_MARVELL 1
+#define CONFIG_ARM926EJS 1 /* Basic Architecture */
+#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
+#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+#define CONFIG_MACH_SHEEVAPLUG /* Machine type */
+
+#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
+
+/*
+ * CLKs configurations
+ */
+#define CONFIG_SYS_HZ 1000
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
+ 115200,230400, 460800, 921600 }
+/* auto boot */
+#define CONFIG_BOOTDELAY 3 /* default enable autoboot */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
+
+#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+
+/*
+ * NAND configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_KIRKWOOD
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */
+#define NAND_ALLOW_ERASE_ALL 1
+#endif
+
+/*
+ * Environment variables configurations
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
+#else
+#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
+#endif
+/*
+ * max 4k env size is enough, but in case of nand
+ * it has to be rounded to sector size
+ */
+#define CONFIG_ENV_SIZE 0x20000 /* 128k */
+#define CONFIG_ENV_ADDR 0x40000
+#define CONFIG_ENV_OFFSET 0x40000 /* env starts here */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
+ "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
+ "${x_bootcmd_usb}; bootm 0x6400000;"
+
+#define CONFIG_MTDPARTS "orion_nand:512k(uboot)," \
+ "3m at 1m(kernel),1m at 4m(psm),13m at 5m(rootfs) rw\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
+ "=ttyS0,115200 mtdparts="CONFIG_MTDPARTS \
+ "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \
+ "x_bootcmd_usb=usb start\0" \
+ "x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2\0"
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 128) /* 128kB for malloc() */
+/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE 128
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */
+#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
+#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
+#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
+#define CONFIG_NR_DRAM_BANKS 4
+#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */
+#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
+#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* specify more that one ports available */
+#define CONFIG_MII /* expose smi ove miiphy interface */
+#define CONFIG_KIRKWOOD_EGIGA /* Enable kirkwood Gbe Controller Driver */
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
+#define CONFIG_KIRKWOOD_EGIGA_PORTS {1,0} /* enable port 0 only */
+#define CONFIG_PHY_BASE_ADR 0
+#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
+#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * USB/EHCI
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#endif /* CONFIG_CMD_USB */
+
+#endif /* _CONFIG_SHEEVAPLUG_H */
--
1.5.3.3
^ permalink raw reply related [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v13 3/6] Marvell MV88F6281GTW_GE Board support
2009-07-16 15:28 ` [U-Boot] [PATCH v7 2/6] Marvell Sheevaplug Board support Prafulla Wadaskar
@ 2009-07-16 15:28 ` Prafulla Wadaskar
2009-07-16 15:28 ` [U-Boot] [PATCH 4/6] net: phy: bugfixes: mv88E61xx multichip addressing support Prafulla Wadaskar
2009-07-18 18:40 ` [U-Boot] [PATCH v13 3/6] Marvell MV88F6281GTW_GE Board support Jean-Christophe PLAGNIOL-VILLARD
2009-07-16 15:32 ` [U-Boot] [PATCH 6/6][repost] Marvell RD6281A " Prafulla Wadaskar
2009-07-18 17:41 ` [U-Boot] [PATCH v7 2/6] Marvell Sheevaplug " Jean-Christophe PLAGNIOL-VILLARD
2 siblings, 2 replies; 33+ messages in thread
From: Prafulla Wadaskar @ 2009-07-16 15:28 UTC (permalink / raw)
To: u-boot
This is Marvell's 88F6281_A0 based custom board developed
for wireless access point product
This patch is tested for-
1. Boot from DRAM/SPI flash/NFS
2. File transfer using tftp and loadb
3. SPI flash read/write/erase
4. Booting Linux kernel and RFS from SPI flash
5. Boot from USB supported
Reviewed-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
---
Change log
v2: updated as per first review comments debug_prints updated to debug
v3: updaed as per review comments for v2 added mv88f6281gtw_ge.h file removed BITxx macros
v4: updated as per review comments for v3 arch_misc_init support is added and used from kirkwood
v5: updated as per review comments for v4 CONFIG_MACH_MV88F6281GTW_GE added more comments added and serial configuration removed from mv88f6281gtw_ge.c
V6: clean switch configuration using netdev.h
v7: Marvell copyright removed from u-boot.lds Maintainer added for this board
v8: u-boot.lds removed
finetuned for cosmetic and switch related changes
v9: new mpp configuration used
CONFIG_ARCH_LOWLEVEL_INIT defination removed
v10: CONFIG_ENV_SIZE set to 4kb
CONFIG_SYS_MALLOC_LEN set to 128kb
v11: updated as per feedback for v10
copyright statement corrected
mtdparts definition corrected
all code lines checked for max len 80 chars
v12: config_cmd_default.h used in board config
entry in MAINTAINERS list added
v13: mv88f6281gtw_ge.h allgined as per cleanup in config_cmd_default.h
MAINTAINERS | 1 +
MAKEALL | 1 +
Makefile | 3 +
board/Marvell/mv88f6281gtw_ge/Makefile | 51 ++++++
board/Marvell/mv88f6281gtw_ge/config.mk | 25 +++
board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c | 141 ++++++++++++++++
board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.h | 36 ++++
include/configs/mv88f6281gtw_ge.h | 200 +++++++++++++++++++++++
8 files changed, 458 insertions(+), 0 deletions(-)
create mode 100644 board/Marvell/mv88f6281gtw_ge/Makefile
create mode 100644 board/Marvell/mv88f6281gtw_ge/config.mk
create mode 100644 board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c
create mode 100644 board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.h
create mode 100644 include/configs/mv88f6281gtw_ge.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 2f3b63c..76268b4 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -675,6 +675,7 @@ Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Prafulla Wadaskar <prafulla@marvell.com>
+ mv88f6281gtw_ge ARM926EJS (Kirkwood SoC)
sheevaplug ARM926EJS (Kirkwood SoC)
Richard Woodruff <r-woodruff2@ti.com>
diff --git a/MAKEALL b/MAKEALL
index e987d4a..4e1f431 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -510,6 +510,7 @@ LIST_ARM9=" \
cp946es \
cp966 \
lpd7a400 \
+ mv88f6281gtw_ge \
mx1ads \
mx1fs2 \
netstar \
diff --git a/Makefile b/Makefile
index a66c4c7..b4d8c80 100644
--- a/Makefile
+++ b/Makefile
@@ -2853,6 +2853,9 @@ lpd7a400_config \
lpd7a404_config: unconfig
@$(MKCONFIG) $(@:_config=) arm lh7a40x lpd7a40x
+mv88f6281gtw_ge_config: unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
+
mx1ads_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm920t mx1ads NULL imx
diff --git a/board/Marvell/mv88f6281gtw_ge/Makefile b/board/Marvell/mv88f6281gtw_ge/Makefile
new file mode 100644
index 0000000..92d0b47
--- /dev/null
+++ b/board/Marvell/mv88f6281gtw_ge/Makefile
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := mv88f6281gtw_ge.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/Marvell/mv88f6281gtw_ge/config.mk b/board/Marvell/mv88f6281gtw_ge/config.mk
new file mode 100644
index 0000000..a4ea769
--- /dev/null
+++ b/board/Marvell/mv88f6281gtw_ge/config.mk
@@ -0,0 +1,25 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+TEXT_BASE = 0x00600000
diff --git a/board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c b/board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c
new file mode 100644
index 0000000..c959bf8
--- /dev/null
+++ b/board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c
@@ -0,0 +1,141 @@
+/*
+ * Maintainer : Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <netdev.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "mv88f6281gtw_ge.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ kw_config_gpio(MV88F6281GTW_GE_OE_VAL_LOW,
+ MV88F6281GTW_GE_OE_VAL_HIGH,
+ MV88F6281GTW_GE_OE_LOW, MV88F6281GTW_GE_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ u32 kwmpp_config[] = {
+ MPP0_SPI_SCn,
+ MPP1_SPI_MOSI,
+ MPP2_SPI_SCK,
+ MPP3_SPI_MISO,
+ MPP4_GPIO,
+ MPP5_GPO,
+ MPP6_SYSRST_OUTn,
+ MPP7_SPI_SCn,
+ MPP8_TW_SDA,
+ MPP9_TW_SCK,
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP12_GPO,
+ MPP13_GPIO,
+ MPP14_GPIO,
+ MPP15_GPIO,
+ MPP16_GPIO,
+ MPP17_GPIO,
+ MPP18_GPO,
+ MPP19_GPO,
+ MPP20_GPIO,
+ MPP21_GPIO,
+ MPP22_GPIO,
+ MPP23_GPIO,
+ MPP24_GPIO,
+ MPP25_GPIO,
+ MPP26_GPIO,
+ MPP27_GPIO,
+ MPP28_GPIO,
+ MPP29_GPIO,
+ MPP30_GPIO,
+ MPP31_GPIO,
+ MPP32_GPIO,
+ MPP33_GPIO,
+ MPP34_GPIO,
+ MPP35_GPIO,
+ MPP36_GPIO,
+ MPP37_GPIO,
+ MPP38_GPIO,
+ MPP39_GPIO,
+ MPP40_GPIO,
+ MPP41_GPIO,
+ MPP42_GPIO,
+ MPP43_GPIO,
+ MPP44_GPIO,
+ MPP45_GPIO,
+ MPP46_GPIO,
+ MPP47_GPIO,
+ MPP48_GPIO,
+ MPP49_GPIO,
+ 0
+ };
+ kirkwood_mpp_conf(kwmpp_config);
+
+ /*
+ * arch number of board
+ */
+ gd->bd->bi_arch_number = MACH_TYPE_MV88F6281GTW_GE;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ int i;
+
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ gd->bd->bi_dram[i].start = kw_sdram_bar(i);
+ gd->bd->bi_dram[i].size = kw_sdram_bs(i);
+ }
+ return 0;
+}
+
+#ifdef CONFIG_MV88E61XX_SWITCH
+void reset_phy(void)
+{
+ /* configure and initialize switch */
+ struct mv88e61xx_config swcfg = {
+ .name = "egiga0",
+ .vlancfg = MV88E61XX_VLANCFG_ROUTER,
+ .rgmii_delay = MV88E61XX_RGMII_DELAY_EN,
+ .led_init = MV88E61XX_LED_INIT_EN,
+ .mdip = MV88E61XX_MDIP_REVERSE,
+ .portstate = MV88E61XX_PORTSTT_FORWARDING,
+ .cpuport = (1 << 5),
+ .ports_enabled = 0x3f
+ };
+
+ mv88e61xx_switch_initialize(&swcfg);
+}
+#endif /* CONFIG_MV88E61XX_SWITCH */
diff --git a/board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.h b/board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.h
new file mode 100644
index 0000000..65b925d
--- /dev/null
+++ b/board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.h
@@ -0,0 +1,36 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __MV88F6281GTW_GE_H
+#define __MV88F6281GTW_GE_H
+
+#define MV88F6281GTW_GE_OE_LOW (~((1 << 7) | (1 << 12) \
+ |(1 << 20) | (1 << 21))) /*enable GLED,RLED */
+#define MV88F6281GTW_GE_OE_HIGH (~((1 << 4)|(1 << 6)|(1 << 7)|(1 << 12) \
+ |(1 << 13)|(1 << 16)|(1 << 17)))
+#define MV88F6281GTW_GE_OE_VAL_LOW (1 << 20) /*make GLED on */
+#define MV88F6281GTW_GE_OE_VAL_HIGH ((1 << 6)|(1 << 13)|(1 << 16)|(1 << 17))
+
+
+#endif /* __MV88F6281GTW_GE_H */
diff --git a/include/configs/mv88f6281gtw_ge.h b/include/configs/mv88f6281gtw_ge.h
new file mode 100644
index 0000000..96b4d1c
--- /dev/null
+++ b/include/configs/mv88f6281gtw_ge.h
@@ -0,0 +1,200 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_MV88F6281GTW_GE_H
+#define _CONFIG_MV88F6281GTW_GE_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING "\nMarvell-MV88F6281GTW_GE"
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_MARVELL 1
+#define CONFIG_ARM926EJS 1 /* Basic Architecture */
+#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
+#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+#define CONFIG_MACH_MV88F6281GTW_GE /* Machine type */
+
+#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
+
+/*
+ * CLKs configurations
+ */
+#define CONFIG_SYS_HZ 1000
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
+ 115200,230400, 460800, 921600 }
+/* auto boot */
+#define CONFIG_BOOTDELAY 3 /* default enable autoboot */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
+
+#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_USB
+
+/*
+ * Flash configuration
+ */
+#ifdef CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH 1
+#define CONFIG_HARD_SPI 1
+#define CONFIG_KIRKWOOD_SPI 1
+#define CONFIG_SPI_FLASH_MACRONIX 1
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 50000000 /*50Mhz */
+#endif
+
+/*
+ * Environment variables configurations
+ */
+#ifdef CONFIG_SPI_FLASH
+#define CONFIG_ENV_IS_IN_SPI_FLASH 1
+#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K */
+#else
+#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
+#endif
+#define CONFIG_ENV_SIZE 0x1000 /* 4k */
+#define CONFIG_ENV_ADDR 0x30000
+#define CONFIG_ENV_OFFSET 0x30000 /* env starts here */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
+ "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
+ "${x_bootcmd_usb}; bootm 0x6400000;"
+
+#define CONFIG_MTDPARTS "spi0.0:512k(uboot)," \
+ "512k at 512k(psm),2m at 1m(kernel),13m at 3m(rootfs)\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
+ "=ttyS0,115200 mtdparts="CONFIG_MTDPARTS \
+ "x_bootcmd_kernel=cp.b 0xE8100000 0x6400000 0x200000\0" \
+ "x_bootcmd_usb=usb start\0" \
+ "x_bootargs_root=root=/dev/mtdblock3 ro rootfstype=squashfs\0"
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 128) /* 128kB for malloc() */
+/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE 128
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */
+#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
+#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
+#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
+#define CONFIG_NR_DRAM_BANKS 4
+#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */
+#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
+#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* specify more that one ports available */
+#define CONFIG_MII /* expose smi ove miiphy interface */
+#define CONFIG_KIRKWOOD_EGIGA /* Enable kirkwood Gbe Controller Driver */
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
+#define CONFIG_KIRKWOOD_EGIGA_PORTS {1,0} /* enable port 0 only */
+#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * Marvell 88Exxxx Switch configurations
+ */
+#define CONFIG_RESET_PHY_R /* use reset_phy() to init phy/swtich */
+#define CONFIG_MV88E61XX_SWITCH /* Enable mv88e61xx switch driver */
+
+/*
+ * USB/EHCI
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#endif /* CONFIG_CMD_USB */
+
+#endif /* _CONFIG_MV88F6281GTW_GE_H */
--
1.5.3.3
^ permalink raw reply related [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 4/6] net: phy: bugfixes: mv88E61xx multichip addressing support
2009-07-16 15:28 ` [U-Boot] [PATCH v13 3/6] Marvell MV88F6281GTW_GE " Prafulla Wadaskar
@ 2009-07-16 15:28 ` Prafulla Wadaskar
2009-07-16 15:28 ` [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support Prafulla Wadaskar
` (2 more replies)
2009-07-18 18:40 ` [U-Boot] [PATCH v13 3/6] Marvell MV88F6281GTW_GE Board support Jean-Christophe PLAGNIOL-VILLARD
1 sibling, 3 replies; 33+ messages in thread
From: Prafulla Wadaskar @ 2009-07-16 15:28 UTC (permalink / raw)
To: u-boot
With these fixes, this driver works properly for multi chip
addressging mode
Bugfixes:
1. Build error fixed for function mv88e61xx_busychk_multic-fixed
2. PHY dev address error detection- fixed
3. wrong busy bit was refered in function mv88e61xx_busychk -fixed
4. invalid data read ptr was refered for RD_PHY in case of
multichip addressing mode -fixed
The Multichip Address mode is tested with RD6281A board having
MV88E6165 switch on it
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
---
drivers/net/phy/mv88e61xx.c | 18 +++++++++---------
drivers/net/phy/mv88e61xx.h | 2 +-
2 files changed, 10 insertions(+), 10 deletions(-)
diff --git a/drivers/net/phy/mv88e61xx.c b/drivers/net/phy/mv88e61xx.c
index ec47286..29630f5 100644
--- a/drivers/net/phy/mv88e61xx.c
+++ b/drivers/net/phy/mv88e61xx.c
@@ -36,7 +36,7 @@
* By default single chip mode is configured
* multichip mode operation can be configured in board header
*/
-static int mv88e61xx_busychk_multic(u32 devaddr)
+static int mv88e61xx_busychk_multic(char *name, u32 devaddr)
{
u32 reg = 0;
u32 timeout = MV88E61XX_PHY_TIMEOUT;
@@ -58,11 +58,11 @@ static void mv88e61xx_wr_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 data)
u32 mii_dev_addr;
/* command to read PHY dev address */
- if (!miiphy_read(name, 0xEE, 0xEE, &mii_dev_addr)) {
+ if (miiphy_read(name, 0xEE, 0xEE, &mii_dev_addr)) {
printf("Error..could not read PHY dev address\n");
return;
}
- mv88e61xx_busychk_multic(mii_dev_addr);
+ mv88e61xx_busychk_multic(name, mii_dev_addr);
/* Write data to Switch indirect data register */
miiphy_write(name, mii_dev_addr, 0x1, data);
/* Write command to Switch indirect command register (write) */
@@ -77,18 +77,18 @@ static void mv88e61xx_rd_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 * data)
u32 mii_dev_addr;
/* command to read PHY dev address */
- if (!miiphy_read(name, 0xEE, 0xEE, &mii_dev_addr)) {
+ if (miiphy_read(name, 0xEE, 0xEE, &mii_dev_addr)) {
printf("Error..could not read PHY dev address\n");
return;
}
- mv88e61xx_busychk_multic(mii_dev_addr);
+ mv88e61xx_busychk_multic(name, mii_dev_addr);
/* Write command to Switch indirect command register (read) */
miiphy_write(name, mii_dev_addr, 0x0,
- reg_ofs | (phy_adr << 5) | (1 << 10) | (1 << 12) | (1 <<
+ reg_ofs | (phy_adr << 5) | (1 << 11) | (1 << 12) | (1 <<
15));
- mv88e61xx_busychk_multic(mii_dev_addr);
+ mv88e61xx_busychk_multic(name, mii_dev_addr);
/* Read data from Switch indirect data register */
- miiphy_read(name, mii_dev_addr, 0x1, (u16 *) & data);
+ miiphy_read(name, mii_dev_addr, 0x1, data);
}
#endif /* CONFIG_MV88E61XX_MULTICHIP_ADRMODE */
@@ -212,7 +212,7 @@ static int mv88e61xx_busychk(char *name)
printf("SMI busy timeout\n");
return -1;
}
- } while (reg & 1 << 28); /* busy mask */
+ } while (reg & 1 << 15); /* busy mask */
return 0;
}
diff --git a/drivers/net/phy/mv88e61xx.h b/drivers/net/phy/mv88e61xx.h
index 4279464..57762b6 100644
--- a/drivers/net/phy/mv88e61xx.h
+++ b/drivers/net/phy/mv88e61xx.h
@@ -49,7 +49,7 @@
#define MV88E61XX_ADDR_OFST 5
#ifdef CONFIG_MV88E61XX_MULTICHIP_ADRMODE
-static int mv88e61xx_busychk_multic(u32 devaddr);
+static int mv88e61xx_busychk_multic(char *name, u32 devaddr);
static void mv88e61xx_wr_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 data);
static void mv88e61xx_rd_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 * data);
#define WR_PHY mv88e61xx_wr_phy
--
1.5.3.3
^ permalink raw reply related [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support
2009-07-16 15:28 ` [U-Boot] [PATCH 4/6] net: phy: bugfixes: mv88E61xx multichip addressing support Prafulla Wadaskar
@ 2009-07-16 15:28 ` Prafulla Wadaskar
2009-07-16 14:45 ` Dieter Kiermaier
` (3 more replies)
2009-07-21 6:52 ` [U-Boot] [PATCH 4/6] net: phy: bugfixes: mv88E61xx multichip addressing support Ben Warren
2009-08-10 8:09 ` Wolfgang Denk
2 siblings, 4 replies; 33+ messages in thread
From: Prafulla Wadaskar @ 2009-07-16 15:28 UTC (permalink / raw)
To: u-boot
By default Auto Negotiation is enabled for interface speed
but on some platforms like RD6281A it does not work.
If you want to forced program it to desired speed,
this patch helps-
Through this patch Auto negotiation can be disabled and
desired interface speed can be configured
This patch is tested on RD6281A Kirkwood board
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
---
drivers/net/kirkwood_egiga.c | 24 ++++++++++++++++++++++++
1 files changed, 24 insertions(+), 0 deletions(-)
diff --git a/drivers/net/kirkwood_egiga.c b/drivers/net/kirkwood_egiga.c
index 3c5db19..1dfd567 100644
--- a/drivers/net/kirkwood_egiga.c
+++ b/drivers/net/kirkwood_egiga.c
@@ -415,7 +415,31 @@ static int kwgbe_init(struct eth_device *dev)
/* Assign port configuration and command. */
KWGBEREG_WR(regs->pxc, PRT_CFG_VAL);
KWGBEREG_WR(regs->pxcx, PORT_CFG_EXTEND_VALUE);
+ /*
+ * Forced 10/100/1000BASE-T interface speed configuration
+ * By default Auto Negotiation of interface speed is enabled
+ * This can be forced disabled and desired speed can be configured
+ */
+#ifdef CONFIG_DIS_AUTO_NEG_SPEED_GMII
+#if (!defined (CONFIG_PHY_SPEED) || (CONFIG_PHY_SPEED == _1000BASET))
+ KWGBEREG_WR(regs->psc0, PORT_SERIAL_CONTROL_VALUE
+ | KWGBE_DIS_AUTO_NEG_SPEED_GMII
+ | KWGBE_SET_GMII_SPEED_TO_1000);
+#elif (CONFIG_PHY_SPEED == _100BASET)
+ KWGBEREG_WR(regs->psc0, PORT_SERIAL_CONTROL_VALUE
+ | KWGBE_DIS_AUTO_NEG_SPEED_GMII
+ | KWGBE_SET_GMII_SPEED_TO_10_100
+ | KWGBE_SET_MII_SPEED_TO_100);
+#elif (CONFIG_PHY_SPEED == _10BASET)
+ KWGBEREG_WR(regs->psc0, PORT_SERIAL_CONTROL_VALUE
+ | KWGBE_DIS_AUTO_NEG_SPEED_GMII
+ | KWGBE_SET_GMII_SPEED_TO_10_100
+ | KWGBE_SET_MII_SPEED_TO_10);
+#endif /* CONFIG_PHY_SPEED == _10BASET */
+#else
KWGBEREG_WR(regs->psc0, PORT_SERIAL_CONTROL_VALUE);
+#endif /* CONFIG_DIS_AUTO_NEG_SPEED_GMII */
+
/* Disable port initially */
KWGBEREG_BITS_SET(regs->psc0, KWGBE_SERIAL_PORT_EN);
--
1.5.3.3
^ permalink raw reply related [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 6/6] Marvell RD6281A Board support
2009-07-16 15:28 ` [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support Prafulla Wadaskar
2009-07-16 14:45 ` Dieter Kiermaier
@ 2009-07-16 15:28 ` Prafulla Wadaskar
2009-07-18 18:48 ` Jean-Christophe PLAGNIOL-VILLARD
2009-07-18 18:43 ` [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support Jean-Christophe PLAGNIOL-VILLARD
2009-07-21 6:51 ` Ben Warren
3 siblings, 1 reply; 33+ messages in thread
From: Prafulla Wadaskar @ 2009-07-16 15:28 UTC (permalink / raw)
To: u-boot
This is Marvell's 88F6281_A0 based reference design board
This patch is tested for-
1. Boot from DRAM/NAND flash/NFS
2. File transfer using tftp and loadb
3. NAND flash read/write/erase
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
---
MAINTAINERS | 1 +
MAKEALL | 1 +
Makefile | 3 +
board/Marvell/rd6281a/Makefile | 51 ++++++++++
board/Marvell/rd6281a/config.mk | 25 +++++
board/Marvell/rd6281a/rd6281a.c | 179 +++++++++++++++++++++++++++++++++
board/Marvell/rd6281a/rd6281a.h | 41 ++++++++
include/configs/rd6281a.h | 209 +++++++++++++++++++++++++++++++++++++++
8 files changed, 510 insertions(+), 0 deletions(-)
create mode 100644 board/Marvell/rd6281a/Makefile
create mode 100644 board/Marvell/rd6281a/config.mk
create mode 100644 board/Marvell/rd6281a/rd6281a.c
create mode 100644 board/Marvell/rd6281a/rd6281a.h
create mode 100644 include/configs/rd6281a.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 76268b4..ff587e1 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -676,6 +676,7 @@ Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Prafulla Wadaskar <prafulla@marvell.com>
mv88f6281gtw_ge ARM926EJS (Kirkwood SoC)
+ rd6281a ARM926EJS (Kirkwood SoC)
sheevaplug ARM926EJS (Kirkwood SoC)
Richard Woodruff <r-woodruff2@ti.com>
diff --git a/MAKEALL b/MAKEALL
index 4e1f431..3d7e4da 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -521,6 +521,7 @@ LIST_ARM9=" \
omap1610inn \
omap5912osk \
omap730p2 \
+ rd6281a \
sbc2410x \
scb9328 \
sheevaplug \
diff --git a/Makefile b/Makefile
index b4d8c80..3a011c8 100644
--- a/Makefile
+++ b/Makefile
@@ -2921,6 +2921,9 @@ omap730p2_cs3boot_config : unconfig
fi;
@$(MKCONFIG) -a $(call xtract_omap730p2,$@) arm arm926ejs omap730p2 NULL omap
+rd6281a_config: unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
+
sbc2410x_config: unconfig
@$(MKCONFIG) $(@:_config=) arm arm920t sbc2410x NULL s3c24x0
diff --git a/board/Marvell/rd6281a/Makefile b/board/Marvell/rd6281a/Makefile
new file mode 100644
index 0000000..907dd7d
--- /dev/null
+++ b/board/Marvell/rd6281a/Makefile
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := rd6281a.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/Marvell/rd6281a/config.mk b/board/Marvell/rd6281a/config.mk
new file mode 100644
index 0000000..a4ea769
--- /dev/null
+++ b/board/Marvell/rd6281a/config.mk
@@ -0,0 +1,25 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+TEXT_BASE = 0x00600000
diff --git a/board/Marvell/rd6281a/rd6281a.c b/board/Marvell/rd6281a/rd6281a.c
new file mode 100644
index 0000000..8713a3c
--- /dev/null
+++ b/board/Marvell/rd6281a/rd6281a.c
@@ -0,0 +1,179 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "rd6281a.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ kw_config_gpio(RD6281A_OE_VAL_LOW,
+ RD6281A_OE_VAL_HIGH,
+ RD6281A_OE_LOW, RD6281A_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ u32 kwmpp_config[] = {
+ MPP0_NF_IO2,
+ MPP1_NF_IO3,
+ MPP2_NF_IO4,
+ MPP3_NF_IO5,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP7_GPO,
+ MPP8_TW_SDA,
+ MPP9_TW_SCK,
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP12_SD_CLK,
+ MPP13_SD_CMD,
+ MPP14_SD_D0,
+ MPP15_SD_D1,
+ MPP16_SD_D2,
+ MPP17_SD_D3,
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_GE1_0,
+ MPP21_GE1_1,
+ MPP22_GE1_2,
+ MPP23_GE1_3,
+ MPP24_GE1_4,
+ MPP25_GE1_5,
+ MPP26_GE1_6,
+ MPP27_GE1_7,
+ MPP28_GPIO,
+ MPP29_GPIO,
+ MPP30_GE1_10,
+ MPP31_GE1_11,
+ MPP32_GE1_12,
+ MPP33_GE1_13,
+ MPP34_GE1_14,
+ MPP35_GPIO,
+ MPP36_AUDIO_SPDIFI,
+ MPP37_AUDIO_SPDIFO,
+ MPP38_GPIO,
+ MPP39_TDM_SPI_CS0,
+ MPP40_TDM_SPI_SCK,
+ MPP41_TDM_SPI_MISO,
+ MPP42_TDM_SPI_MOSI,
+ MPP43_TDM_CODEC_INTn,
+ MPP44_GPIO,
+ MPP45_TDM_PCLK,
+ MPP46_TDM_FS,
+ MPP47_TDM_DRX,
+ MPP48_TDM_DTX,
+ MPP49_GPIO,
+ 0
+ };
+ kirkwood_mpp_conf(kwmpp_config);
+
+ /*
+ * arch number of board
+ */
+ gd->bd->bi_arch_number = MACH_TYPE_RD88F6281;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ int i;
+
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ gd->bd->bi_dram[i].start = kw_sdram_bar(i);
+ gd->bd->bi_dram[i].size = kw_sdram_bs(i);
+ }
+ return 0;
+}
+
+void mv_phy_88e1116_init(char *name)
+{
+ u16 reg;
+ u16 devadr;
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ /* command to read PHY dev address */
+ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+ printf("Err..%s could not read PHY dev address\n",
+ __FUNCTION__);
+ return;
+ }
+
+ /*
+ * Enable RGMII delay on Tx and Rx for CPU port
+ * Ref: sec 4.7.2 of chip datasheet
+ */
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
+ miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
+ reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+ miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
+
+ /* reset the phy */
+ if (miiphy_read (name, devadr, PHY_BMCR, ®) != 0) {
+ printf("Err..(%s) PHY status read failed\n", __FUNCTION__);
+ return;
+ }
+ if (miiphy_write (name, devadr, PHY_BMCR, reg | 0x8000) != 0) {
+ printf("Err..(%s) PHY reset failed\n", __FUNCTION__);
+ return;
+ }
+
+ printf("88E1116 Initialized on %s\n", name);
+}
+
+/* Configure and enable Switch and PHY */
+void reset_phy(void)
+{
+ /* configure and initialize switch */
+ struct mv88e61xx_config swcfg = {
+ .name = "egiga0",
+ .vlancfg = MV88E61XX_VLANCFG_ROUTER,
+ .rgmii_delay = MV88E61XX_RGMII_DELAY_EN,
+ .led_init = MV88E61XX_LED_INIT_EN,
+ .portstate = MV88E61XX_PORTSTT_FORWARDING,
+ .cpuport = (1 << 5),
+ .ports_enabled = 0x3f,
+ };
+
+ mv88e61xx_switch_initialize(&swcfg);
+
+ /* configure and initialize PHY */
+ mv_phy_88e1116_init("egiga1");
+}
diff --git a/board/Marvell/rd6281a/rd6281a.h b/board/Marvell/rd6281a/rd6281a.h
new file mode 100644
index 0000000..c978bef
--- /dev/null
+++ b/board/Marvell/rd6281a/rd6281a.h
@@ -0,0 +1,41 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __RD6281A_H
+#define __RD6281A_H
+
+#define RD6281A_OE_LOW (~(1 << 7))
+#define RD6281A_OE_HIGH (~(1 << 2 | 1 << 12))
+#define RD6281A_OE_VAL_LOW (0)
+#define RD6281A_OE_VAL_HIGH (1 << 12)
+
+/* PHY related */
+#define MV88E1116_LED_FCTRL_REG 10
+#define MV88E1116_CPRSP_CR3_REG 21
+#define MV88E1116_MAC_CTRL_REG 21
+#define MV88E1116_PGADR_REG 22
+#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
+
+#endif /* __RD6281A_H */
diff --git a/include/configs/rd6281a.h b/include/configs/rd6281a.h
new file mode 100644
index 0000000..065e4aa
--- /dev/null
+++ b/include/configs/rd6281a.h
@@ -0,0 +1,209 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_RD6281A_H
+#define _CONFIG_RD6281A_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING "\nMarvell-Sheevaplug"
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_MARVELL 1
+#define CONFIG_ARM926EJS 1 /* Basic Architecture */
+#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
+#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+#define CONFIG_MACH_RD6281A /* Machine type */
+
+#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
+
+/*
+ * CLKs configurations
+ */
+#define CONFIG_SYS_HZ 1000
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
+ 115200,230400, 460800, 921600 }
+/* auto boot */
+#define CONFIG_BOOTDELAY 3 /* default enable autoboot */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
+
+#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
+/*
+ * Commands configuration
+ */
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_USB
+
+/*
+ * Flash configuration
+ */
+#ifndef CONFIG_CMD_FLASH
+#define CONFIG_SYS_NO_FLASH 1 /* Declare no flash (NOR/SPI) */
+#endif
+
+/*
+ * NAND configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_KIRKWOOD
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */
+#define NAND_ALLOW_ERASE_ALL 1
+#endif
+
+/*
+ * Environment variables configurations
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
+#else
+#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
+#endif
+/*
+ * max 4k env size is enough, but in case of nand
+ * it has to be rounded to sector size
+ */
+#define CONFIG_ENV_SIZE 0x20000 /* 128k */
+#define CONFIG_ENV_ADDR 0x40000
+#define CONFIG_ENV_OFFSET 0x40000 /* env starts here */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
+ "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
+ "${x_bootcmd_usb}; bootm 0x6400000;"
+
+#define CONFIG_MTDPARTS "orion_nand:512k(uboot)," \
+ "3m at 1m(kernel),1m at 4m(psm),13m at 5m(rootfs) rw\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
+ "=ttyS0,115200 mtdparts="CONFIG_MTDPARTS \
+ "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \
+ "x_bootcmd_usb=usb start\0" \
+ "x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2\0"
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 128) /* 128kB for malloc() */
+/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE 128
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */
+#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
+#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
+#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
+#define CONFIG_NR_DRAM_BANKS 4
+#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */
+#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
+#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* specify more that one ports available */
+#define CONFIG_MII /* expose smi ove miiphy interface */
+#define CONFIG_KIRKWOOD_EGIGA /* Enable kirkwood Gbe Controller Driver */
+#define CONFIG_KIRKWOOD_EGIGA_PORTS {1,1} /* enable both ports */
+#define CONFIG_MV88E61XX_MULTICHIP_ADRMODE
+#define CONFIG_DIS_AUTO_NEG_SPEED_GMII /*Disable Auto speed negociation */
+#define CONFIG_PHY_SPEED _1000BASET /*Force PHYspeed to 1GBPs */
+#define CONFIG_PHY_BASE_ADR 0x0A
+#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
+#define CONFIG_RESET_PHY_R /* use reset_phy() to init switch and PHY */
+#define CONFIG_MV88E61XX_SWITCH /* Enable MV88E61XX switch driver */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * USB/EHCI
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#endif /* CONFIG_CMD_USB */
+
+#endif /* _CONFIG_RD6281A_H */
--
1.5.3.3
^ permalink raw reply related [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 6/6][repost] Marvell RD6281A Board support
@ 2009-07-16 15:32 ` Prafulla Wadaskar
2009-07-22 22:15 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 1 reply; 33+ messages in thread
From: Prafulla Wadaskar @ 2009-07-16 15:32 UTC (permalink / raw)
To: u-boot
This is Marvell's 88F6281_A0 based reference design board
This patch is tested for-
1. Boot from DRAM/NAND flash/NFS
2. File transfer using tftp and loadb
3. NAND flash read/write/erase
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
---
Change log:
Sorry.. One commit was missing...
MAINTAINERS | 1 +
MAKEALL | 1 +
Makefile | 3 +
board/Marvell/rd6281a/Makefile | 51 ++++++++++
board/Marvell/rd6281a/config.mk | 25 +++++
board/Marvell/rd6281a/rd6281a.c | 179 +++++++++++++++++++++++++++++++++++
board/Marvell/rd6281a/rd6281a.h | 41 ++++++++
include/configs/rd6281a.h | 198 +++++++++++++++++++++++++++++++++++++++
8 files changed, 499 insertions(+), 0 deletions(-)
create mode 100644 board/Marvell/rd6281a/Makefile
create mode 100644 board/Marvell/rd6281a/config.mk
create mode 100644 board/Marvell/rd6281a/rd6281a.c
create mode 100644 board/Marvell/rd6281a/rd6281a.h
create mode 100644 include/configs/rd6281a.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 76268b4..ff587e1 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -676,6 +676,7 @@ Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Prafulla Wadaskar <prafulla@marvell.com>
mv88f6281gtw_ge ARM926EJS (Kirkwood SoC)
+ rd6281a ARM926EJS (Kirkwood SoC)
sheevaplug ARM926EJS (Kirkwood SoC)
Richard Woodruff <r-woodruff2@ti.com>
diff --git a/MAKEALL b/MAKEALL
index 4e1f431..3d7e4da 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -521,6 +521,7 @@ LIST_ARM9=" \
omap1610inn \
omap5912osk \
omap730p2 \
+ rd6281a \
sbc2410x \
scb9328 \
sheevaplug \
diff --git a/Makefile b/Makefile
index b4d8c80..3a011c8 100644
--- a/Makefile
+++ b/Makefile
@@ -2921,6 +2921,9 @@ omap730p2_cs3boot_config : unconfig
fi;
@$(MKCONFIG) -a $(call xtract_omap730p2,$@) arm arm926ejs omap730p2 NULL omap
+rd6281a_config: unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
+
sbc2410x_config: unconfig
@$(MKCONFIG) $(@:_config=) arm arm920t sbc2410x NULL s3c24x0
diff --git a/board/Marvell/rd6281a/Makefile b/board/Marvell/rd6281a/Makefile
new file mode 100644
index 0000000..907dd7d
--- /dev/null
+++ b/board/Marvell/rd6281a/Makefile
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := rd6281a.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/Marvell/rd6281a/config.mk b/board/Marvell/rd6281a/config.mk
new file mode 100644
index 0000000..a4ea769
--- /dev/null
+++ b/board/Marvell/rd6281a/config.mk
@@ -0,0 +1,25 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+TEXT_BASE = 0x00600000
diff --git a/board/Marvell/rd6281a/rd6281a.c b/board/Marvell/rd6281a/rd6281a.c
new file mode 100644
index 0000000..8713a3c
--- /dev/null
+++ b/board/Marvell/rd6281a/rd6281a.c
@@ -0,0 +1,179 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "rd6281a.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ kw_config_gpio(RD6281A_OE_VAL_LOW,
+ RD6281A_OE_VAL_HIGH,
+ RD6281A_OE_LOW, RD6281A_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ u32 kwmpp_config[] = {
+ MPP0_NF_IO2,
+ MPP1_NF_IO3,
+ MPP2_NF_IO4,
+ MPP3_NF_IO5,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP7_GPO,
+ MPP8_TW_SDA,
+ MPP9_TW_SCK,
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP12_SD_CLK,
+ MPP13_SD_CMD,
+ MPP14_SD_D0,
+ MPP15_SD_D1,
+ MPP16_SD_D2,
+ MPP17_SD_D3,
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_GE1_0,
+ MPP21_GE1_1,
+ MPP22_GE1_2,
+ MPP23_GE1_3,
+ MPP24_GE1_4,
+ MPP25_GE1_5,
+ MPP26_GE1_6,
+ MPP27_GE1_7,
+ MPP28_GPIO,
+ MPP29_GPIO,
+ MPP30_GE1_10,
+ MPP31_GE1_11,
+ MPP32_GE1_12,
+ MPP33_GE1_13,
+ MPP34_GE1_14,
+ MPP35_GPIO,
+ MPP36_AUDIO_SPDIFI,
+ MPP37_AUDIO_SPDIFO,
+ MPP38_GPIO,
+ MPP39_TDM_SPI_CS0,
+ MPP40_TDM_SPI_SCK,
+ MPP41_TDM_SPI_MISO,
+ MPP42_TDM_SPI_MOSI,
+ MPP43_TDM_CODEC_INTn,
+ MPP44_GPIO,
+ MPP45_TDM_PCLK,
+ MPP46_TDM_FS,
+ MPP47_TDM_DRX,
+ MPP48_TDM_DTX,
+ MPP49_GPIO,
+ 0
+ };
+ kirkwood_mpp_conf(kwmpp_config);
+
+ /*
+ * arch number of board
+ */
+ gd->bd->bi_arch_number = MACH_TYPE_RD88F6281;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ int i;
+
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ gd->bd->bi_dram[i].start = kw_sdram_bar(i);
+ gd->bd->bi_dram[i].size = kw_sdram_bs(i);
+ }
+ return 0;
+}
+
+void mv_phy_88e1116_init(char *name)
+{
+ u16 reg;
+ u16 devadr;
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ /* command to read PHY dev address */
+ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+ printf("Err..%s could not read PHY dev address\n",
+ __FUNCTION__);
+ return;
+ }
+
+ /*
+ * Enable RGMII delay on Tx and Rx for CPU port
+ * Ref: sec 4.7.2 of chip datasheet
+ */
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
+ miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
+ reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+ miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
+
+ /* reset the phy */
+ if (miiphy_read (name, devadr, PHY_BMCR, ®) != 0) {
+ printf("Err..(%s) PHY status read failed\n", __FUNCTION__);
+ return;
+ }
+ if (miiphy_write (name, devadr, PHY_BMCR, reg | 0x8000) != 0) {
+ printf("Err..(%s) PHY reset failed\n", __FUNCTION__);
+ return;
+ }
+
+ printf("88E1116 Initialized on %s\n", name);
+}
+
+/* Configure and enable Switch and PHY */
+void reset_phy(void)
+{
+ /* configure and initialize switch */
+ struct mv88e61xx_config swcfg = {
+ .name = "egiga0",
+ .vlancfg = MV88E61XX_VLANCFG_ROUTER,
+ .rgmii_delay = MV88E61XX_RGMII_DELAY_EN,
+ .led_init = MV88E61XX_LED_INIT_EN,
+ .portstate = MV88E61XX_PORTSTT_FORWARDING,
+ .cpuport = (1 << 5),
+ .ports_enabled = 0x3f,
+ };
+
+ mv88e61xx_switch_initialize(&swcfg);
+
+ /* configure and initialize PHY */
+ mv_phy_88e1116_init("egiga1");
+}
diff --git a/board/Marvell/rd6281a/rd6281a.h b/board/Marvell/rd6281a/rd6281a.h
new file mode 100644
index 0000000..c978bef
--- /dev/null
+++ b/board/Marvell/rd6281a/rd6281a.h
@@ -0,0 +1,41 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __RD6281A_H
+#define __RD6281A_H
+
+#define RD6281A_OE_LOW (~(1 << 7))
+#define RD6281A_OE_HIGH (~(1 << 2 | 1 << 12))
+#define RD6281A_OE_VAL_LOW (0)
+#define RD6281A_OE_VAL_HIGH (1 << 12)
+
+/* PHY related */
+#define MV88E1116_LED_FCTRL_REG 10
+#define MV88E1116_CPRSP_CR3_REG 21
+#define MV88E1116_MAC_CTRL_REG 21
+#define MV88E1116_PGADR_REG 22
+#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
+
+#endif /* __RD6281A_H */
diff --git a/include/configs/rd6281a.h b/include/configs/rd6281a.h
new file mode 100644
index 0000000..ef16579
--- /dev/null
+++ b/include/configs/rd6281a.h
@@ -0,0 +1,198 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_RD6281A_H
+#define _CONFIG_RD6281A_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING "\nMarvell-RD6281A"
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_MARVELL 1
+#define CONFIG_ARM926EJS 1 /* Basic Architecture */
+#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
+#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+#define CONFIG_MACH_RD6281A /* Machine type */
+
+#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
+
+/*
+ * CLKs configurations
+ */
+#define CONFIG_SYS_HZ 1000
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
+ 115200,230400, 460800, 921600 }
+/* auto boot */
+#define CONFIG_BOOTDELAY 3 /* default enable autoboot */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
+
+#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+
+/*
+ * NAND configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_KIRKWOOD
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */
+#define NAND_ALLOW_ERASE_ALL 1
+#endif
+
+/*
+ * Environment variables configurations
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
+#else
+#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
+#endif
+/*
+ * max 4k env size is enough, but in case of nand
+ * it has to be rounded to sector size
+ */
+#define CONFIG_ENV_SIZE 0x20000 /* 128k */
+#define CONFIG_ENV_ADDR 0x40000
+#define CONFIG_ENV_OFFSET 0x40000 /* env starts here */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
+ "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
+ "${x_bootcmd_usb}; bootm 0x6400000;"
+
+#define CONFIG_MTDPARTS "orion_nand:512k(uboot)," \
+ "3m at 1m(kernel),1m at 4m(psm),13m at 5m(rootfs) rw\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
+ "=ttyS0,115200 mtdparts="CONFIG_MTDPARTS \
+ "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \
+ "x_bootcmd_usb=usb start\0" \
+ "x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2\0"
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 128) /* 128kB for malloc() */
+/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE 128
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */
+#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
+#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
+#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
+#define CONFIG_NR_DRAM_BANKS 4
+#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */
+#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
+#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* specify more that one ports available */
+#define CONFIG_MII /* expose smi ove miiphy interface */
+#define CONFIG_KIRKWOOD_EGIGA /* Enable kirkwood Gbe Controller Driver */
+#define CONFIG_KIRKWOOD_EGIGA_PORTS {1,1} /* enable both ports */
+#define CONFIG_MV88E61XX_MULTICHIP_ADRMODE
+#define CONFIG_DIS_AUTO_NEG_SPEED_GMII /*Disable Auto speed negociation */
+#define CONFIG_PHY_SPEED _1000BASET /*Force PHYspeed to 1GBPs */
+#define CONFIG_PHY_BASE_ADR 0x0A
+#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
+#define CONFIG_RESET_PHY_R /* use reset_phy() to init switch and PHY */
+#define CONFIG_MV88E61XX_SWITCH /* Enable MV88E61XX switch driver */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * USB/EHCI
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#endif /* CONFIG_CMD_USB */
+
+#endif /* _CONFIG_RD6281A_H */
--
1.5.3.3
^ permalink raw reply related [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support
2009-07-16 14:45 ` Dieter Kiermaier
@ 2009-07-16 15:45 ` Prafulla Wadaskar
0 siblings, 0 replies; 33+ messages in thread
From: Prafulla Wadaskar @ 2009-07-16 15:45 UTC (permalink / raw)
To: u-boot
> -----Original Message-----
> From: Dieter Kiermaier [mailto:dk-arm-linux at gmx.de]
> Sent: Thursday, July 16, 2009 8:15 PM
> To: u-boot at lists.denx.de
> Cc: Prafulla Wadaskar; Manas Saksena; Ronen Shitrit; Nicolas
> Pitre; Ashish Karkare; Prabhanjan Sarnaik; Lennert Buijtenhek
> Subject: Re: [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced
> interface speed config support
>
> Hi Prafulla, hi Marvell engineers,
>
>
> > By default Auto Negotiation is enabled for interface speed
> but on some
> > platforms like RD6281A it does not work.
> > If you want to forced program it to desired speed, this patch helps-
>
> do you have some information why auto negotiation doesn't
> work on RD6281A?
Hi Dieter
I do not have good answer for this with me :-(
On RD6281A I thought Auto negotiation should work, but it did not.
During my debugging, I performed several trial and error methods and forcing PHY interface speed to 1000BPs worked for me.
So I exposed this configuration through this patch.
I will certainly look for better answer for you
Regards..
Prafulla . .
> I'm working on custom hardware and don't want to do the same
> mistake :)
>
> Many thanks,
> Dieter
>
>
>
> >
> > Through this patch Auto negotiation can be disabled and desired
> > interface speed can be configured
> >
> > This patch is tested on RD6281A Kirkwood board
> >
> > Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
> > ---
> > drivers/net/kirkwood_egiga.c | 24 ++++++++++++++++++++++++
> > 1 files changed, 24 insertions(+), 0 deletions(-)
> >
> > diff --git a/drivers/net/kirkwood_egiga.c
> > b/drivers/net/kirkwood_egiga.c index 3c5db19..1dfd567 100644
> > --- a/drivers/net/kirkwood_egiga.c
> > +++ b/drivers/net/kirkwood_egiga.c
> > @@ -415,7 +415,31 @@ static int kwgbe_init(struct eth_device *dev)
> > /* Assign port configuration and command. */
> > KWGBEREG_WR(regs->pxc, PRT_CFG_VAL);
> > KWGBEREG_WR(regs->pxcx, PORT_CFG_EXTEND_VALUE);
> > + /*
> > + * Forced 10/100/1000BASE-T interface speed configuration
> > + * By default Auto Negotiation of interface speed is enabled
> > + * This can be forced disabled and desired speed can be
> configured
> > + */
> > +#ifdef CONFIG_DIS_AUTO_NEG_SPEED_GMII #if (!defined
> > +(CONFIG_PHY_SPEED) || (CONFIG_PHY_SPEED == _1000BASET))
> > + KWGBEREG_WR(regs->psc0, PORT_SERIAL_CONTROL_VALUE
> > + | KWGBE_DIS_AUTO_NEG_SPEED_GMII
> > + | KWGBE_SET_GMII_SPEED_TO_1000);
> > +#elif (CONFIG_PHY_SPEED == _100BASET)
> > + KWGBEREG_WR(regs->psc0, PORT_SERIAL_CONTROL_VALUE
> > + | KWGBE_DIS_AUTO_NEG_SPEED_GMII
> > + | KWGBE_SET_GMII_SPEED_TO_10_100
> > + | KWGBE_SET_MII_SPEED_TO_100);
> > +#elif (CONFIG_PHY_SPEED == _10BASET)
> > + KWGBEREG_WR(regs->psc0, PORT_SERIAL_CONTROL_VALUE
> > + | KWGBE_DIS_AUTO_NEG_SPEED_GMII
> > + | KWGBE_SET_GMII_SPEED_TO_10_100
> > + | KWGBE_SET_MII_SPEED_TO_10);
> > +#endif /* CONFIG_PHY_SPEED == _10BASET */ #else
> > KWGBEREG_WR(regs->psc0, PORT_SERIAL_CONTROL_VALUE);
> > +#endif /* CONFIG_DIS_AUTO_NEG_SPEED_GMII */
> > +
> > /* Disable port initially */
> > KWGBEREG_BITS_SET(regs->psc0, KWGBE_SERIAL_PORT_EN);
> >
>
>
>
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 1/6] include/config_cmd_default.h cleanup
2009-07-16 15:27 [U-Boot] [PATCH 1/6] include/config_cmd_default.h cleanup Prafulla Wadaskar
2009-07-16 15:28 ` [U-Boot] [PATCH v7 2/6] Marvell Sheevaplug Board support Prafulla Wadaskar
@ 2009-07-17 21:26 ` Wolfgang Denk
1 sibling, 0 replies; 33+ messages in thread
From: Wolfgang Denk @ 2009-07-17 21:26 UTC (permalink / raw)
To: u-boot
Dear Prafulla Wadaskar,
In message <1247758084-12296-1-git-send-email-prafulla@marvell.com> you wrote:
> arranged configurations in alphabetical order
> CONFIG_CMD_FLASH moved under ifndef CONFIG_SYS_NO_FLASH
>
> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
> ---
> include/config_cmd_default.h | 6 +++---
> 1 files changed, 3 insertions(+), 3 deletions(-)
Applied, thanks.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
I am a computer. I am dumber than any human and smarter than any ad-
ministrator.
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v7 2/6] Marvell Sheevaplug Board support
2009-07-16 15:28 ` [U-Boot] [PATCH v7 2/6] Marvell Sheevaplug Board support Prafulla Wadaskar
2009-07-16 15:28 ` [U-Boot] [PATCH v13 3/6] Marvell MV88F6281GTW_GE " Prafulla Wadaskar
2009-07-16 15:32 ` [U-Boot] [PATCH 6/6][repost] Marvell RD6281A " Prafulla Wadaskar
@ 2009-07-18 17:41 ` Jean-Christophe PLAGNIOL-VILLARD
2009-07-19 4:56 ` Prafulla Wadaskar
2 siblings, 1 reply; 33+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2009-07-18 17:41 UTC (permalink / raw)
To: u-boot
On 20:58 Thu 16 Jul , Prafulla Wadaskar wrote:
> Reference:
> http://plugcomputer.org/
> http://openplug.org/plugwiki/index.php/Das_U-boot_plug_support
>
> This patch is tested for-
> 1. Boot from DRAM/NAND flash
> 2. File transfer using tftp
> 3. NAND flash read/write/erase
> 4. Linux kernel and RFS Boot from NAND
> 5. Enabled USB PHY init for kernel need
> 6. Boot from USB supported
>
> Note: to boot Kirkwood kernel with USB support,
> you should add "usb start" in the boot sequence
>
> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Applied to u-boot-arm
Best Regards,
J.
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v13 3/6] Marvell MV88F6281GTW_GE Board support
2009-07-16 15:28 ` [U-Boot] [PATCH v13 3/6] Marvell MV88F6281GTW_GE " Prafulla Wadaskar
2009-07-16 15:28 ` [U-Boot] [PATCH 4/6] net: phy: bugfixes: mv88E61xx multichip addressing support Prafulla Wadaskar
@ 2009-07-18 18:40 ` Jean-Christophe PLAGNIOL-VILLARD
2009-07-19 4:55 ` Prafulla Wadaskar
1 sibling, 1 reply; 33+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2009-07-18 18:40 UTC (permalink / raw)
To: u-boot
On 20:58 Thu 16 Jul , Prafulla Wadaskar wrote:
> This is Marvell's 88F6281_A0 based custom board developed
> for wireless access point product
>
> This patch is tested for-
> 1. Boot from DRAM/SPI flash/NFS
> 2. File transfer using tftp and loadb
> 3. SPI flash read/write/erase
> 4. Booting Linux kernel and RFS from SPI flash
> 5. Boot from USB supported
>
> Reviewed-by: Ronen Shitrit <rshitrit@marvell.com>
> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
> ---
applied to u-boot-arm
Best Regards,
J.
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support
2009-07-16 15:28 ` [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support Prafulla Wadaskar
2009-07-16 14:45 ` Dieter Kiermaier
2009-07-16 15:28 ` [U-Boot] [PATCH 6/6] Marvell RD6281A Board support Prafulla Wadaskar
@ 2009-07-18 18:43 ` Jean-Christophe PLAGNIOL-VILLARD
2009-07-19 4:54 ` Prafulla Wadaskar
2009-07-21 6:22 ` Ben Warren
2009-07-21 6:51 ` Ben Warren
3 siblings, 2 replies; 33+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2009-07-18 18:43 UTC (permalink / raw)
To: u-boot
On 20:58 Thu 16 Jul , Prafulla Wadaskar wrote:
> By default Auto Negotiation is enabled for interface speed
> but on some platforms like RD6281A it does not work.
> If you want to forced program it to desired speed,
> this patch helps-
>
> Through this patch Auto negotiation can be disabled and
> desired interface speed can be configured
>
> This patch is tested on RD6281A Kirkwood board
>
> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
> ---
> drivers/net/kirkwood_egiga.c | 24 ++++++++++++++++++++++++
> 1 files changed, 24 insertions(+), 0 deletions(-)
>
> diff --git a/drivers/net/kirkwood_egiga.c b/drivers/net/kirkwood_egiga.c
> index 3c5db19..1dfd567 100644
> --- a/drivers/net/kirkwood_egiga.c
> +++ b/drivers/net/kirkwood_egiga.c
> @@ -415,7 +415,31 @@ static int kwgbe_init(struct eth_device *dev)
> /* Assign port configuration and command. */
> KWGBEREG_WR(regs->pxc, PRT_CFG_VAL);
> KWGBEREG_WR(regs->pxcx, PORT_CFG_EXTEND_VALUE);
> + /*
> + * Forced 10/100/1000BASE-T interface speed configuration
> + * By default Auto Negotiation of interface speed is enabled
> + * This can be forced disabled and desired speed can be configured
> + */
> +#ifdef CONFIG_DIS_AUTO_NEG_SPEED_GMII
> +#if (!defined (CONFIG_PHY_SPEED) || (CONFIG_PHY_SPEED == _1000BASET))
Could you find a better config taht _1000BASET & co
Best Regards,
J.
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 6/6] Marvell RD6281A Board support
2009-07-16 15:28 ` [U-Boot] [PATCH 6/6] Marvell RD6281A Board support Prafulla Wadaskar
@ 2009-07-18 18:48 ` Jean-Christophe PLAGNIOL-VILLARD
2009-07-19 4:50 ` Prafulla Wadaskar
0 siblings, 1 reply; 33+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2009-07-18 18:48 UTC (permalink / raw)
To: u-boot
> diff --git a/include/configs/rd6281a.h b/include/configs/rd6281a.h
> new file mode 100644
> index 0000000..065e4aa
> --- /dev/null
> +++ b/include/configs/rd6281a.h
> @@ -0,0 +1,209 @@
> +/*
> + * (C) Copyright 2009
> + * Marvell Semiconductor <www.marvell.com>
> + * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
> + * MA 02110-1301 USA
> + */
> +
> +#ifndef _CONFIG_RD6281A_H
> +#define _CONFIG_RD6281A_H
> +
> +/*
> + * Version number information
> + */
> +#define CONFIG_IDENT_STRING "\nMarvell-Sheevaplug"
???
Sheevaplug?
Best Regards,
J.
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 6/6] Marvell RD6281A Board support
2009-07-18 18:48 ` Jean-Christophe PLAGNIOL-VILLARD
@ 2009-07-19 4:50 ` Prafulla Wadaskar
0 siblings, 0 replies; 33+ messages in thread
From: Prafulla Wadaskar @ 2009-07-19 4:50 UTC (permalink / raw)
To: u-boot
> -----Original Message-----
> From: Jean-Christophe PLAGNIOL-VILLARD [mailto:plagnioj at jcrosoft.com]
> Sent: Sunday, July 19, 2009 12:18 AM
> To: Prafulla Wadaskar
> Cc: u-boot at lists.denx.de; Manas Saksena; Ronen Shitrit;
> Nicolas Pitre; Ashish Karkare; Prabhanjan Sarnaik; Lennert Buijtenhek
> Subject: Re: [U-Boot] [PATCH 6/6] Marvell RD6281A Board support
>
> > diff --git a/include/configs/rd6281a.h
> b/include/configs/rd6281a.h new
> > file mode 100644 index 0000000..065e4aa
> > --- /dev/null
> > +++ b/include/configs/rd6281a.h
> > @@ -0,0 +1,209 @@
> > +/*
> > + * (C) Copyright 2009
> > + * Marvell Semiconductor <www.marvell.com>
> > + * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
> > + *
> > + * See file CREDITS for list of people who contributed to this
> > + * project.
> > + *
> > + * This program is free software; you can redistribute it and/or
> > + * modify it under the terms of the GNU General Public License as
> > + * published by the Free Software Foundation; either version 2 of
> > + * the License, or (at your option) any later version.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + *
> > + * You should have received a copy of the GNU General
> Public License
> > + * along with this program; if not, write to the Free Software
> > + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
> > + * MA 02110-1301 USA
> > + */
> > +
> > +#ifndef _CONFIG_RD6281A_H
> > +#define _CONFIG_RD6281A_H
> > +
> > +/*
> > + * Version number information
> > + */
> > +#define CONFIG_IDENT_STRING "\nMarvell-Sheevaplug"
> ???
> Sheevaplug?
Sorry.. I observed this after git-send :-) , patch already reposted
Reference: http://lists.denx.de/pipermail/u-boot/2009-July/056438.html
Regards..
Prafulla . .
>
> Best Regards,
> J.
>
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support
2009-07-18 18:43 ` [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support Jean-Christophe PLAGNIOL-VILLARD
@ 2009-07-19 4:54 ` Prafulla Wadaskar
2009-07-21 6:22 ` Ben Warren
1 sibling, 0 replies; 33+ messages in thread
From: Prafulla Wadaskar @ 2009-07-19 4:54 UTC (permalink / raw)
To: u-boot
> -----Original Message-----
> From: Jean-Christophe PLAGNIOL-VILLARD [mailto:plagnioj at jcrosoft.com]
> Sent: Sunday, July 19, 2009 12:14 AM
> To: Prafulla Wadaskar
> Cc: u-boot at lists.denx.de; Manas Saksena; Ronen Shitrit;
> Nicolas Pitre; Ashish Karkare; Prabhanjan Sarnaik; Lennert Buijtenhek
> Subject: Re: [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced
> interface speed config support
>
> On 20:58 Thu 16 Jul , Prafulla Wadaskar wrote:
> > By default Auto Negotiation is enabled for interface speed
> but on some
> > platforms like RD6281A it does not work.
> > If you want to forced program it to desired speed, this patch helps-
> >
> > Through this patch Auto negotiation can be disabled and desired
> > interface speed can be configured
> >
> > This patch is tested on RD6281A Kirkwood board
> >
> > Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
> > ---
> > drivers/net/kirkwood_egiga.c | 24 ++++++++++++++++++++++++
> > 1 files changed, 24 insertions(+), 0 deletions(-)
> >
> > diff --git a/drivers/net/kirkwood_egiga.c
> > b/drivers/net/kirkwood_egiga.c index 3c5db19..1dfd567 100644
> > --- a/drivers/net/kirkwood_egiga.c
> > +++ b/drivers/net/kirkwood_egiga.c
> > @@ -415,7 +415,31 @@ static int kwgbe_init(struct eth_device *dev)
> > /* Assign port configuration and command. */
> > KWGBEREG_WR(regs->pxc, PRT_CFG_VAL);
> > KWGBEREG_WR(regs->pxcx, PORT_CFG_EXTEND_VALUE);
> > + /*
> > + * Forced 10/100/1000BASE-T interface speed configuration
> > + * By default Auto Negotiation of interface speed is enabled
> > + * This can be forced disabled and desired speed can be
> configured
> > + */
> > +#ifdef CONFIG_DIS_AUTO_NEG_SPEED_GMII #if (!defined
> > +(CONFIG_PHY_SPEED) || (CONFIG_PHY_SPEED == _1000BASET))
> Could you find a better config taht _1000BASET & co
Hi Jean,
I have reused it from include/miiphy.h which is relevant too.
Regards..
Prafulla . .
>
> Best Regards,
> J.
>
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v13 3/6] Marvell MV88F6281GTW_GE Board support
2009-07-18 18:40 ` [U-Boot] [PATCH v13 3/6] Marvell MV88F6281GTW_GE Board support Jean-Christophe PLAGNIOL-VILLARD
@ 2009-07-19 4:55 ` Prafulla Wadaskar
0 siblings, 0 replies; 33+ messages in thread
From: Prafulla Wadaskar @ 2009-07-19 4:55 UTC (permalink / raw)
To: u-boot
> -----Original Message-----
> From: Jean-Christophe PLAGNIOL-VILLARD [mailto:plagnioj at jcrosoft.com]
> Sent: Sunday, July 19, 2009 12:11 AM
> To: Prafulla Wadaskar
> Cc: u-boot at lists.denx.de; Manas Saksena; Ronen Shitrit;
> Nicolas Pitre; Ashish Karkare; Prabhanjan Sarnaik; Lennert Buijtenhek
> Subject: Re: [U-Boot] [PATCH v13 3/6] Marvell MV88F6281GTW_GE
> Board support
>
> On 20:58 Thu 16 Jul , Prafulla Wadaskar wrote:
> > This is Marvell's 88F6281_A0 based custom board developed
> for wireless
> > access point product
> >
> > This patch is tested for-
> > 1. Boot from DRAM/SPI flash/NFS
> > 2. File transfer using tftp and loadb
> > 3. SPI flash read/write/erase
> > 4. Booting Linux kernel and RFS from SPI flash 5. Boot from USB
> > supported
> >
> > Reviewed-by: Ronen Shitrit <rshitrit@marvell.com>
> > Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
> > ---
> applied to u-boot-arm
Thanks Jean..
Regards..
Prafulla . .
>
> Best Regards,
> J.
>
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH v7 2/6] Marvell Sheevaplug Board support
2009-07-18 17:41 ` [U-Boot] [PATCH v7 2/6] Marvell Sheevaplug " Jean-Christophe PLAGNIOL-VILLARD
@ 2009-07-19 4:56 ` Prafulla Wadaskar
0 siblings, 0 replies; 33+ messages in thread
From: Prafulla Wadaskar @ 2009-07-19 4:56 UTC (permalink / raw)
To: u-boot
> -----Original Message-----
> From: Jean-Christophe PLAGNIOL-VILLARD [mailto:plagnioj at jcrosoft.com]
> Sent: Saturday, July 18, 2009 11:11 PM
> To: Prafulla Wadaskar
> Cc: u-boot at lists.denx.de; Manas Saksena; Ronen Shitrit;
> Nicolas Pitre; Ashish Karkare; Prabhanjan Sarnaik; Lennert Buijtenhek
> Subject: Re: [U-Boot] [PATCH v7 2/6] Marvell Sheevaplug Board support
>
> On 20:58 Thu 16 Jul , Prafulla Wadaskar wrote:
> > Reference:
> > http://plugcomputer.org/
> > http://openplug.org/plugwiki/index.php/Das_U-boot_plug_support
> >
> > This patch is tested for-
> > 1. Boot from DRAM/NAND flash
> > 2. File transfer using tftp
> > 3. NAND flash read/write/erase
> > 4. Linux kernel and RFS Boot from NAND 5. Enabled USB PHY init for
> > kernel need 6. Boot from USB supported
> >
> > Note: to boot Kirkwood kernel with USB support,
> > you should add "usb start" in the boot sequence
> >
> > Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
> Applied to u-boot-arm
Thank you Jean..
Regards..
Prafulla . .
>
> Best Regards,
> J.
>
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support
2009-07-18 18:43 ` [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support Jean-Christophe PLAGNIOL-VILLARD
2009-07-19 4:54 ` Prafulla Wadaskar
@ 2009-07-21 6:22 ` Ben Warren
2009-07-21 7:39 ` Wolfgang Denk
2009-07-21 19:08 ` Prafulla Wadaskar
1 sibling, 2 replies; 33+ messages in thread
From: Ben Warren @ 2009-07-21 6:22 UTC (permalink / raw)
To: u-boot
Jean-Christophe PLAGNIOL-VILLARD wrote:
> On 20:58 Thu 16 Jul , Prafulla Wadaskar wrote:
>
>> By default Auto Negotiation is enabled for interface speed
>> but on some platforms like RD6281A it does not work.
>> If you want to forced program it to desired speed,
>> this patch helps-
>>
>> Through this patch Auto negotiation can be disabled and
>> desired interface speed can be configured
>>
>> This patch is tested on RD6281A Kirkwood board
>>
>> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
>> ---
>> drivers/net/kirkwood_egiga.c | 24 ++++++++++++++++++++++++
>> 1 files changed, 24 insertions(+), 0 deletions(-)
>>
>> diff --git a/drivers/net/kirkwood_egiga.c b/drivers/net/kirkwood_egiga.c
>> index 3c5db19..1dfd567 100644
>> --- a/drivers/net/kirkwood_egiga.c
>> +++ b/drivers/net/kirkwood_egiga.c
>> @@ -415,7 +415,31 @@ static int kwgbe_init(struct eth_device *dev)
>> /* Assign port configuration and command. */
>> KWGBEREG_WR(regs->pxc, PRT_CFG_VAL);
>> KWGBEREG_WR(regs->pxcx, PORT_CFG_EXTEND_VALUE);
>> + /*
>> + * Forced 10/100/1000BASE-T interface speed configuration
>> + * By default Auto Negotiation of interface speed is enabled
>> + * This can be forced disabled and desired speed can be configured
>> + */
>> +#ifdef CONFIG_DIS_AUTO_NEG_SPEED_GMII
>> +#if (!defined (CONFIG_PHY_SPEED) || (CONFIG_PHY_SPEED == _1000BASET))
>>
> Could you find a better config taht _1000BASET & co
>
>
Global configs for this type of thing are a bad idea (what if you want
one interface @ 1000 and one @ 100? I guess this will have to do for
now, but let's ensure that it's temporary.
> Best Regards,
> J.
regards,
Ben
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support
2009-07-16 15:28 ` [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support Prafulla Wadaskar
` (2 preceding siblings ...)
2009-07-18 18:43 ` [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support Jean-Christophe PLAGNIOL-VILLARD
@ 2009-07-21 6:51 ` Ben Warren
2009-07-21 7:41 ` Wolfgang Denk
3 siblings, 1 reply; 33+ messages in thread
From: Ben Warren @ 2009-07-21 6:51 UTC (permalink / raw)
To: u-boot
Prafulla,
Prafulla Wadaskar wrote:
> By default Auto Negotiation is enabled for interface speed
> but on some platforms like RD6281A it does not work.
> If you want to forced program it to desired speed,
> this patch helps-
>
> Through this patch Auto negotiation can be disabled and
> desired interface speed can be configured
>
> This patch is tested on RD6281A Kirkwood board
>
> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
> ---
Applied to net repo.
thanks,
Ben
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 4/6] net: phy: bugfixes: mv88E61xx multichip addressing support
2009-07-16 15:28 ` [U-Boot] [PATCH 4/6] net: phy: bugfixes: mv88E61xx multichip addressing support Prafulla Wadaskar
2009-07-16 15:28 ` [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support Prafulla Wadaskar
@ 2009-07-21 6:52 ` Ben Warren
2009-08-10 8:09 ` Wolfgang Denk
2 siblings, 0 replies; 33+ messages in thread
From: Ben Warren @ 2009-07-21 6:52 UTC (permalink / raw)
To: u-boot
Prafulla,
Prafulla Wadaskar wrote:
> With these fixes, this driver works properly for multi chip
> addressging mode
>
> Bugfixes:
> 1. Build error fixed for function mv88e61xx_busychk_multic-fixed
> 2. PHY dev address error detection- fixed
> 3. wrong busy bit was refered in function mv88e61xx_busychk -fixed
> 4. invalid data read ptr was refered for RD_PHY in case of
> multichip addressing mode -fixed
>
> The Multichip Address mode is tested with RD6281A board having
> MV88E6165 switch on it
>
> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
> ---
Applied to net repo.
thanks,
Ben
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support
2009-07-21 6:22 ` Ben Warren
@ 2009-07-21 7:39 ` Wolfgang Denk
2009-07-21 19:08 ` Prafulla Wadaskar
1 sibling, 0 replies; 33+ messages in thread
From: Wolfgang Denk @ 2009-07-21 7:39 UTC (permalink / raw)
To: u-boot
Dear Ben Warren,
In message <4A655EAA.4000401@gmail.com> you wrote:
>
> >> By default Auto Negotiation is enabled for interface speed
> >> but on some platforms like RD6281A it does not work.
What exactly is the reason that it doesn't work?
Is it some deficiency of the board hardware that always exaists, or a
problem only present in combination with certain switches. or what
exactly?
> >> If you want to forced program it to desired speed,
> >> this patch helps-
> >>
> >> Through this patch Auto negotiation can be disabled and
> >> desired interface speed can be configured
I'm not sure if it's really a good idea to do hard-code this as a
compile-time option.
> >> +#if (!defined (CONFIG_PHY_SPEED) || (CONFIG_PHY_SPEED == _1000BASET))
> >>
> > Could you find a better config taht _1000BASET & co
> >
> >
> Global configs for this type of thing are a bad idea (what if you want
> one interface @ 1000 and one @ 100? I guess this will have to do for
> now, but let's ensure that it's temporary.
I am not convinced that such a patch should go in at all.
Foir the boards that really need such a configuration, it should be
possible to set this for example using a standard "mii" command as
part of a "preboot" environment setting.
This way the user can disable it at runtime (if he doesn;t need it),
and we don't need to change the code.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"Go to Heaven for the climate, Hell for the company." - Mark Twain
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support
2009-07-21 6:51 ` Ben Warren
@ 2009-07-21 7:41 ` Wolfgang Denk
2009-07-21 7:43 ` Ben Warren
0 siblings, 1 reply; 33+ messages in thread
From: Wolfgang Denk @ 2009-07-21 7:41 UTC (permalink / raw)
To: u-boot
Dear Ben Warren,
In message <4A656563.9020207@gmail.com> you wrote:
>
> Prafulla Wadaskar wrote:
> > By default Auto Negotiation is enabled for interface speed
> > but on some platforms like RD6281A it does not work.
> > If you want to forced program it to desired speed,
> > this patch helps-
> >
> > Through this patch Auto negotiation can be disabled and
> > desired interface speed can be configured
> >
> > This patch is tested on RD6281A Kirkwood board
> >
> > Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
> > ---
> Applied to net repo.
Please reconsider - see my previous comment. [Sorry it came so late.]
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
You're too beautiful to ignore. Too much woman.
-- Kirk to Yeoman Rand, "The Enemy Within", stardate unknown
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support
2009-07-21 7:41 ` Wolfgang Denk
@ 2009-07-21 7:43 ` Ben Warren
2009-07-21 19:01 ` Prafulla Wadaskar
0 siblings, 1 reply; 33+ messages in thread
From: Ben Warren @ 2009-07-21 7:43 UTC (permalink / raw)
To: u-boot
Wolfgang Denk wrote:
> Dear Ben Warren,
>
> In message <4A656563.9020207@gmail.com> you wrote:
>
>> Prafulla Wadaskar wrote:
>>
>>> By default Auto Negotiation is enabled for interface speed
>>> but on some platforms like RD6281A it does not work.
>>> If you want to forced program it to desired speed,
>>> this patch helps-
>>>
>>> Through this patch Auto negotiation can be disabled and
>>> desired interface speed can be configured
>>>
>>> This patch is tested on RD6281A Kirkwood board
>>>
>>> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
>>> ---
>>>
>> Applied to net repo.
>>
>
> Please reconsider - see my previous comment. [Sorry it came so late.]
>
> Best regards,
>
> Wolfgang Denk
>
>
No problem. I assumed it was a chip erratum but should have looked
closer. Let's wait for Prafulla's response.
regards,
Ben
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support
2009-07-21 7:43 ` Ben Warren
@ 2009-07-21 19:01 ` Prafulla Wadaskar
2009-07-21 19:20 ` Jean-Christophe PLAGNIOL-VILLARD
2009-07-21 19:32 ` Lennert Buytenhek
0 siblings, 2 replies; 33+ messages in thread
From: Prafulla Wadaskar @ 2009-07-21 19:01 UTC (permalink / raw)
To: u-boot
> -----Original Message-----
> From: Ben Warren [mailto:biggerbadderben at gmail.com]
> Sent: Tuesday, July 21, 2009 1:14 PM
> To: Wolfgang Denk
> Cc: Prafulla Wadaskar; Manas Saksena; Ronen Shitrit; Nicolas
> Pitre; u-boot at lists.denx.de; Ashish Karkare; Prabhanjan
> Sarnaik; Lennert Buijtenhek
> Subject: Re: [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced
> interface speed config support
>
> Wolfgang Denk wrote:
> > Dear Ben Warren,
> >
> > In message <4A656563.9020207@gmail.com> you wrote:
> >
> >> Prafulla Wadaskar wrote:
> >>
> >>> By default Auto Negotiation is enabled for interface speed but on
> >>> some platforms like RD6281A it does not work.
> >>> If you want to forced program it to desired speed, this
> patch helps-
> >>>
> >>> Through this patch Auto negotiation can be disabled and desired
> >>> interface speed can be configured
> >>>
> >>> This patch is tested on RD6281A Kirkwood board
> >>>
> >>> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
> >>> ---
> >>>
> >> Applied to net repo.
> >>
> >
> > Please reconsider - see my previous comment. [Sorry it came
> so late.]
> >
> > Best regards,
> >
> > Wolfgang Denk
> >
> >
> No problem. I assumed it was a chip erratum but should have
> looked closer. Let's wait for Prafulla's response.
Ideally auto negotiation must work, but :-(
I don't think this is not for SoC/PHY erratum since both are working okay with other boards.
Only the difference is on RD6281A the multichip mode is used,
I am discovering why it is not working.
Meanwhile this patch does not harm anything, it enables RD6281A usecase
We can undo it latter if I could positively discover the fix ;-D
Regards..
Prafulla . .
>
> regards,
> Ben
>
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support
2009-07-21 6:22 ` Ben Warren
2009-07-21 7:39 ` Wolfgang Denk
@ 2009-07-21 19:08 ` Prafulla Wadaskar
1 sibling, 0 replies; 33+ messages in thread
From: Prafulla Wadaskar @ 2009-07-21 19:08 UTC (permalink / raw)
To: u-boot
> -----Original Message-----
> From: Ben Warren [mailto:biggerbadderben at gmail.com]
> Sent: Tuesday, July 21, 2009 11:53 AM
> To: Jean-Christophe PLAGNIOL-VILLARD
> Cc: Prafulla Wadaskar; Manas Saksena; Ronen Shitrit; Nicolas
> Pitre; u-boot at lists.denx.de; Ashish Karkare; Prabhanjan
> Sarnaik; Lennert Buijtenhek
> Subject: Re: [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced
> interface speed config support
>
> Jean-Christophe PLAGNIOL-VILLARD wrote:
> > On 20:58 Thu 16 Jul , Prafulla Wadaskar wrote:
> >
> >> By default Auto Negotiation is enabled for interface speed but on
> >> some platforms like RD6281A it does not work.
> >> If you want to forced program it to desired speed, this
> patch helps-
> >>
> >> Through this patch Auto negotiation can be disabled and desired
> >> interface speed can be configured
> >>
> >> This patch is tested on RD6281A Kirkwood board
> >>
> >> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
> >> ---
> >> drivers/net/kirkwood_egiga.c | 24 ++++++++++++++++++++++++
> >> 1 files changed, 24 insertions(+), 0 deletions(-)
> >>
> >> diff --git a/drivers/net/kirkwood_egiga.c
> >> b/drivers/net/kirkwood_egiga.c index 3c5db19..1dfd567 100644
> >> --- a/drivers/net/kirkwood_egiga.c
> >> +++ b/drivers/net/kirkwood_egiga.c
> >> @@ -415,7 +415,31 @@ static int kwgbe_init(struct eth_device *dev)
> >> /* Assign port configuration and command. */
> >> KWGBEREG_WR(regs->pxc, PRT_CFG_VAL);
> >> KWGBEREG_WR(regs->pxcx, PORT_CFG_EXTEND_VALUE);
> >> + /*
> >> + * Forced 10/100/1000BASE-T interface speed configuration
> >> + * By default Auto Negotiation of interface speed is enabled
> >> + * This can be forced disabled and desired speed can be
> configured
> >> + */
> >> +#ifdef CONFIG_DIS_AUTO_NEG_SPEED_GMII #if (!defined
> >> +(CONFIG_PHY_SPEED) || (CONFIG_PHY_SPEED == _1000BASET))
> >>
> > Could you find a better config taht _1000BASET & co
> >
> >
> Global configs for this type of thing are a bad idea (what if
> you want one interface @ 1000 and one @ 100? I guess this
> will have to do for now, but let's ensure that it's temporary.
I agree. I will find better way to configure this stuff.
Regards..
Prafulla ..
>
> > Best Regards,
> > J.
>
> regards,
> Ben
>
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support
2009-07-21 19:01 ` Prafulla Wadaskar
@ 2009-07-21 19:20 ` Jean-Christophe PLAGNIOL-VILLARD
2009-07-21 19:32 ` Lennert Buytenhek
1 sibling, 0 replies; 33+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2009-07-21 19:20 UTC (permalink / raw)
To: u-boot
> > >
> > > Wolfgang Denk
> > >
> > >
> > No problem. I assumed it was a chip erratum but should have
> > looked closer. Let's wait for Prafulla's response.
> Ideally auto negotiation must work, but :-(
> I don't think this is not for SoC/PHY erratum since both are working okay with other boards.
> Only the difference is on RD6281A the multichip mode is used,
> I am discovering why it is not working.
>
> Meanwhile this patch does not harm anything, it enables RD6281A usecase
> We can undo it latter if I could positively discover the fix ;-D
I agree that need to be debug and fix
but until Prafulla will found the bug, it will a least make the network
working
maybe we could forced it at the runtime instead
Best Regards,
J.
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support
2009-07-21 19:01 ` Prafulla Wadaskar
2009-07-21 19:20 ` Jean-Christophe PLAGNIOL-VILLARD
@ 2009-07-21 19:32 ` Lennert Buytenhek
1 sibling, 0 replies; 33+ messages in thread
From: Lennert Buytenhek @ 2009-07-21 19:32 UTC (permalink / raw)
To: u-boot
On Tue, Jul 21, 2009 at 12:01:49PM -0700, Prafulla Wadaskar wrote:
> > >>> By default Auto Negotiation is enabled for interface speed but on
> > >>> some platforms like RD6281A it does not work.
> > >>> If you want to forced program it to desired speed, this
> > patch helps-
> > >>>
> > >>> Through this patch Auto negotiation can be disabled and desired
> > >>> interface speed can be configured
> > >>>
> > >>> This patch is tested on RD6281A Kirkwood board
> > >>>
> > >>> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
> > >>> ---
> > >>>
> > >> Applied to net repo.
> > >>
> > >
> > > Please reconsider - see my previous comment. [Sorry it came
> > so late.]
> > >
> > > Best regards,
> > >
> > > Wolfgang Denk
> > >
> > >
> > No problem. I assumed it was a chip erratum but should have
> > looked closer. Let's wait for Prafulla's response.
>
> Ideally auto negotiation must work, but :-(
> I don't think this is not for SoC/PHY erratum since both are working
> okay with other boards.
> Only the difference is on RD6281A the multichip mode is used,
> I am discovering why it is not working.
Isn't it just because on the RD6281A, the first ethernet MAC of the
CPU is connected to an ethernet switch chip instead of an ethernet PHY,
and therefore there is no negotiation to be done? (The second MAC
is connected to a PHY directly, so that one should just use autoneg.)
Even on the RD6281Z, we should just force the ethernet MAC to a
fixed speed/duplex, since even though PHY polling might work there,
we'll be talking to the PHY corresponding to the first switch port,
which means that you might not be able to tftp from the second switch
port or so if there's nothing plugged into the first one.
FWIW, the linux kernel port also forces 1000/full on the CPU MACs where
a switch chip is connected. On those CPU MACs where there is a switch
chip connected, the (R)(G)MII interface becomes purely a bus to
transport packets into and out of the crossbar, one that is always up.
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 6/6][repost] Marvell RD6281A Board support
2009-07-16 15:32 ` [U-Boot] [PATCH 6/6][repost] Marvell RD6281A " Prafulla Wadaskar
@ 2009-07-22 22:15 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 33+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2009-07-22 22:15 UTC (permalink / raw)
To: u-boot
On 21:02 Thu 16 Jul , Prafulla Wadaskar wrote:
> This is Marvell's 88F6281_A0 based reference design board
>
> This patch is tested for-
> 1. Boot from DRAM/NAND flash/NFS
> 2. File transfer using tftp and loadb
> 3. NAND flash read/write/erase
>
> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
> ---
> Change log:
> Sorry.. One commit was missing...
applied to u-boot-arm
Best Regards,
J.
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 4/6] net: phy: bugfixes: mv88E61xx multichip addressing support
2009-07-16 15:28 ` [U-Boot] [PATCH 4/6] net: phy: bugfixes: mv88E61xx multichip addressing support Prafulla Wadaskar
2009-07-16 15:28 ` [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support Prafulla Wadaskar
2009-07-21 6:52 ` [U-Boot] [PATCH 4/6] net: phy: bugfixes: mv88E61xx multichip addressing support Ben Warren
@ 2009-08-10 8:09 ` Wolfgang Denk
2009-08-10 8:25 ` Wolfgang Denk
2009-08-10 8:31 ` Prafulla Wadaskar
2 siblings, 2 replies; 33+ messages in thread
From: Wolfgang Denk @ 2009-08-10 8:09 UTC (permalink / raw)
To: u-boot
Dear Prafulla Wadaskar,
In message <1247758084-12296-4-git-send-email-prafulla@marvell.com> you wrote:
> With these fixes, this driver works properly for multi chip
> addressging mode
>
> Bugfixes:
> 1. Build error fixed for function mv88e61xx_busychk_multic-fixed
> 2. PHY dev address error detection- fixed
> 3. wrong busy bit was refered in function mv88e61xx_busychk -fixed
> 4. invalid data read ptr was refered for RD_PHY in case of
> multichip addressing mode -fixed
>
> The Multichip Address mode is tested with RD6281A board having
> MV88E6165 switch on it
>
> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
> ---
> drivers/net/phy/mv88e61xx.c | 18 +++++++++---------
> drivers/net/phy/mv88e61xx.h | 2 +-
> 2 files changed, 10 insertions(+), 10 deletions(-)
This patch causes compiler warnings:
mv88e61xx.c: In function 'mv88e61xx_busychk_multic':
mv88e61xx.c:46: warning: passing argument 4 of 'miiphy_read' from incompatible pointer type
mv88e61xx.c: In function 'mv88e61xx_wr_phy':
mv88e61xx.c:61: warning: passing argument 4 of 'miiphy_read' from incompatible pointer type
mv88e61xx.c:57: warning: unused variable 'reg'
mv88e61xx.c: In function 'mv88e61xx_rd_phy':
mv88e61xx.c:80: warning: passing argument 4 of 'miiphy_read' from incompatible pointer type
mv88e61xx.c:76: warning: unused variable 'reg'
(when building for the rd6281a board using ELDK 4.2, i. e. gcc-4.2.2)
Also, the rd6281a board throws this warning:
nand_util.c:45:2: warning: #warning Please define CONFIG_SYS_64BIT_VSPRINTF for correct output!
Could you please provide fixes?
Thanks in advance.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"One thing they don't tell you about doing experimental physics is
that sometimes you must work under adverse conditions... like a state
of sheer terror." - W. K. Hartmann
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 4/6] net: phy: bugfixes: mv88E61xx multichip addressing support
2009-08-10 8:09 ` Wolfgang Denk
@ 2009-08-10 8:25 ` Wolfgang Denk
2009-08-10 8:59 ` Prafulla Wadaskar
2009-08-10 8:31 ` Prafulla Wadaskar
1 sibling, 1 reply; 33+ messages in thread
From: Wolfgang Denk @ 2009-08-10 8:25 UTC (permalink / raw)
To: u-boot
Dear Prafulla Wadaskar,
In message <1247758084-12296-4-git-send-email-prafulla@marvell.com> you wrote:
> With these fixes, this driver works properly for multi chip
> addressging mode
>
> Bugfixes:
> 1. Build error fixed for function mv88e61xx_busychk_multic-fixed
> 2. PHY dev address error detection- fixed
> 3. wrong busy bit was refered in function mv88e61xx_busychk -fixed
> 4. invalid data read ptr was refered for RD_PHY in case of
> multichip addressing mode -fixed
>
> The Multichip Address mode is tested with RD6281A board having
> MV88E6165 switch on it
>
> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
> ---
> drivers/net/phy/mv88e61xx.c | 18 +++++++++---------
> drivers/net/phy/mv88e61xx.h | 2 +-
> 2 files changed, 10 insertions(+), 10 deletions(-)
With ELDK 4.1 (gcc 4.0.0) I also get this compiler warning:
mv88e61xx.c: In function 'mv88e61xx_switch_initialize':
mv88e61xx.c:346: warning: 'idstr' may be used uninitialized in this function
when building for the mv88f6281gtw_ge board.
This looks reasonabme, as
361 if (reg == 0x1610)
362 idstr = "88E6161";
363 if (reg == 0x1650)
364 idstr = "88E6165";
365 if (reg == 0x1210) {
366 idstr = "88E6123";
367 /* ports 2,3,4 not available */
368 swconfig->ports_enabled &= 0x023;
369 }
may ideed leave "idstr" uninitialized; you may want to change this
into a switch() construct and add a default: case.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Always try to do things in chronological order; it's less confusing
that way.
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 4/6] net: phy: bugfixes: mv88E61xx multichip addressing support
2009-08-10 8:09 ` Wolfgang Denk
2009-08-10 8:25 ` Wolfgang Denk
@ 2009-08-10 8:31 ` Prafulla Wadaskar
1 sibling, 0 replies; 33+ messages in thread
From: Prafulla Wadaskar @ 2009-08-10 8:31 UTC (permalink / raw)
To: u-boot
> -----Original Message-----
> From: Wolfgang Denk [mailto:wd at denx.de]
> Sent: Monday, August 10, 2009 1:39 PM
> To: Prafulla Wadaskar
> Cc: u-boot at lists.denx.de; Manas Saksena; Ronen Shitrit;
> Nicolas Pitre; Ashish Karkare; Prabhanjan Sarnaik; Lennert
> Buijtenhek; Ben Warren; Jean-Christophe Plagniol-Villard
> Subject: Re: [U-Boot] [PATCH 4/6] net: phy: bugfixes:
> mv88E61xx multichip addressing support
>
> Dear Prafulla Wadaskar,
>
> In message
> <1247758084-12296-4-git-send-email-prafulla@marvell.com> you wrote:
> > With these fixes, this driver works properly for multi chip
> > addressging mode
<snip..>
> Also, the rd6281a board throws this warning:
>
> nand_util.c:45:2: warning: #warning Please define
> CONFIG_SYS_64BIT_VSPRINTF for correct output!
Patch posted for this
Regards..
Prafulla . .
>
>
> Could you please provide fixes?
>
> Thanks in advance.
>
> Best regards,
>
> Wolfgang Denk
>
> --
> DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email:
> wd at denx.de "One thing they don't tell you about doing
> experimental physics is that sometimes you must work under
> adverse conditions... like a state
> of sheer terror." - W. K. Hartmann
>
^ permalink raw reply [flat|nested] 33+ messages in thread
* [U-Boot] [PATCH 4/6] net: phy: bugfixes: mv88E61xx multichip addressing support
2009-08-10 8:25 ` Wolfgang Denk
@ 2009-08-10 8:59 ` Prafulla Wadaskar
0 siblings, 0 replies; 33+ messages in thread
From: Prafulla Wadaskar @ 2009-08-10 8:59 UTC (permalink / raw)
To: u-boot
> -----Original Message-----
> From: Wolfgang Denk [mailto:wd at denx.de]
> Sent: Monday, August 10, 2009 1:56 PM
> To: Prafulla Wadaskar
> Cc: Manas Saksena; Ronen Shitrit; Nicolas Pitre; Ben Warren;
> u-boot at lists.denx.de; Ashish Karkare; Prabhanjan Sarnaik;
> Lennert Buijtenhek
> Subject: Re: [U-Boot] [PATCH 4/6] net: phy: bugfixes:
> mv88E61xx multichip addressing support
>
> Dear Prafulla Wadaskar,
>
> In message
> <1247758084-12296-4-git-send-email-prafulla@marvell.com> you wrote:
> > With these fixes, this driver works properly for multi chip
> > addressging mode
> >
> > Bugfixes:
> > 1. Build error fixed for function mv88e61xx_busychk_multic-fixed 2.
> > PHY dev address error detection- fixed 3. wrong busy bit
> was refered
> > in function mv88e61xx_busychk -fixed 4. invalid data read ptr was
> > refered for RD_PHY in case of
> > multichip addressing mode -fixed
> >
> > The Multichip Address mode is tested with RD6281A board having
> > MV88E6165 switch on it
> >
> > Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
> > ---
> > drivers/net/phy/mv88e61xx.c | 18 +++++++++---------
> > drivers/net/phy/mv88e61xx.h | 2 +-
> > 2 files changed, 10 insertions(+), 10 deletions(-)
>
> With ELDK 4.1 (gcc 4.0.0) I also get this compiler warning:
>
> mv88e61xx.c: In function 'mv88e61xx_switch_initialize':
> mv88e61xx.c:346: warning: 'idstr' may be used uninitialized
> in this function
>
> when building for the mv88f6281gtw_ge board.
>
> This looks reasonabme, as
>
> 361 if (reg == 0x1610)
> 362 idstr = "88E6161";
> 363 if (reg == 0x1650)
> 364 idstr = "88E6165";
> 365 if (reg == 0x1210) {
> 366 idstr = "88E6123";
> 367 /* ports 2,3,4 not available */
> 368 swconfig->ports_enabled &= 0x023;
> 369 }
>
> may ideed leave "idstr" uninitialized; you may want to change
> this into a switch() construct and add a default: case.
Thanks
Bugfix patch posted for this
Regards..
Prafulla . .
>
> Best regards,
>
> Wolfgang Denk
>
> --
> DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email:
> wd at denx.de Always try to do things in chronological order;
> it's less confusing that way.
>
^ permalink raw reply [flat|nested] 33+ messages in thread
end of thread, other threads:[~2009-08-10 8:59 UTC | newest]
Thread overview: 33+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-07-16 15:27 [U-Boot] [PATCH 1/6] include/config_cmd_default.h cleanup Prafulla Wadaskar
2009-07-16 15:28 ` [U-Boot] [PATCH v7 2/6] Marvell Sheevaplug Board support Prafulla Wadaskar
2009-07-16 15:28 ` [U-Boot] [PATCH v13 3/6] Marvell MV88F6281GTW_GE " Prafulla Wadaskar
2009-07-16 15:28 ` [U-Boot] [PATCH 4/6] net: phy: bugfixes: mv88E61xx multichip addressing support Prafulla Wadaskar
2009-07-16 15:28 ` [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support Prafulla Wadaskar
2009-07-16 14:45 ` Dieter Kiermaier
2009-07-16 15:45 ` Prafulla Wadaskar
2009-07-16 15:28 ` [U-Boot] [PATCH 6/6] Marvell RD6281A Board support Prafulla Wadaskar
2009-07-18 18:48 ` Jean-Christophe PLAGNIOL-VILLARD
2009-07-19 4:50 ` Prafulla Wadaskar
2009-07-18 18:43 ` [U-Boot] [PATCH 5/6] net: Kirkwood_egiga: forced interface speed config support Jean-Christophe PLAGNIOL-VILLARD
2009-07-19 4:54 ` Prafulla Wadaskar
2009-07-21 6:22 ` Ben Warren
2009-07-21 7:39 ` Wolfgang Denk
2009-07-21 19:08 ` Prafulla Wadaskar
2009-07-21 6:51 ` Ben Warren
2009-07-21 7:41 ` Wolfgang Denk
2009-07-21 7:43 ` Ben Warren
2009-07-21 19:01 ` Prafulla Wadaskar
2009-07-21 19:20 ` Jean-Christophe PLAGNIOL-VILLARD
2009-07-21 19:32 ` Lennert Buytenhek
2009-07-21 6:52 ` [U-Boot] [PATCH 4/6] net: phy: bugfixes: mv88E61xx multichip addressing support Ben Warren
2009-08-10 8:09 ` Wolfgang Denk
2009-08-10 8:25 ` Wolfgang Denk
2009-08-10 8:59 ` Prafulla Wadaskar
2009-08-10 8:31 ` Prafulla Wadaskar
2009-07-18 18:40 ` [U-Boot] [PATCH v13 3/6] Marvell MV88F6281GTW_GE Board support Jean-Christophe PLAGNIOL-VILLARD
2009-07-19 4:55 ` Prafulla Wadaskar
2009-07-16 15:32 ` [U-Boot] [PATCH 6/6][repost] Marvell RD6281A " Prafulla Wadaskar
2009-07-22 22:15 ` Jean-Christophe PLAGNIOL-VILLARD
2009-07-18 17:41 ` [U-Boot] [PATCH v7 2/6] Marvell Sheevaplug " Jean-Christophe PLAGNIOL-VILLARD
2009-07-19 4:56 ` Prafulla Wadaskar
2009-07-17 21:26 ` [U-Boot] [PATCH 1/6] include/config_cmd_default.h cleanup Wolfgang Denk
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox