* [U-Boot] U-boot hangs in mtest in MPC8280 Board
@ 2009-07-30 11:33 GurumurthyGowdar
2009-07-30 12:12 ` Heiko Schocher
2009-07-30 12:23 ` Jerry Van Baren
0 siblings, 2 replies; 12+ messages in thread
From: GurumurthyGowdar @ 2009-07-30 11:33 UTC (permalink / raw)
To: u-boot
On Thu, 30 Jul 2009 16:14:30 +0530 wrote
>Hello GurumurthyGowdar,
>
>GurumurthyGowdar wrote:
>> On Thu, 30 Jul 2009 12:54:31 +0530 ?wrote
>>> Hello GurumurthyGowdar,
>>>
>>> GurumurthyGowdar wrote:
>>>> i am using MPC8280 in our board which has 512MB of SDRAM i.e. from micron.
>>> Is this board in mainline, so I can look in the Source Code?
>> yes this board is in mainline.only one board.
>
>And which board is it? means ? it is MPC8280 based board called remote I/O board
>As I saw in your log, it uses the "normal" mtest. Try to use
>
>CONFIG_SYS_ALT_MEMTEST
how to use this...where to add...command for this test??
>
>instead. (Hopefully, this is available in 1.3.1 ...)
>
>>> Which u-boot version?
>> U-boot version is 1.3.1.
>
>Hmm.. this is very old ...
which is the latest version of u-boot ,can i upgrade the current version of u-boot to latest version i.e. from u-boot 1.3.1 to latest u-boot without reinstalling ELDK
>
>>> Which SDRAMs?
>> SDRAM is MT48LC32M16A2 from Micron.
>>>> when i give command mtest ?only for 1MB to check memory test from U-boot, machine check and program exception is coming after 40 - 60mins later it hangs giving program check exception
>>> Hmm... maybe problems with your SDRAMs?
>> if it is SDRAM problem it should not work for 1hour also i think.
>
>Why not?
ok
>
>>> Is this error shown always after 40-60 mins, not sometimes also earlier?
>> maximum i am able to run mtest for 1hr 30 mins. sometimes it hangs with 45mins also.
>
>Not earlier?
sometimes earlier but rare
>
>Hmm...
>
>>> Can you boot a Linux Kernel for example?
>> No. our job is to only give the board with U-boot boot loader, Linux booting is done by our client.
>
>But you can try it ...
>This would help here, to stress more the SDRAMs ... also you
>can do better memtests there/with it.
i got one new error which is below :-
U-Boot 1.3.1 (Jul 27 2009 - 17:27:10)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 3x, VCO Div 4, 60x Bus Freq 16-50 , Core Freq 50-150
- dfbrg 1, corecnf 0x10, busdf 4, cpmdf 1, plldf 0, pllmf 4, pcidf 3
- vco_out 500000000, scc_clk 125000000, brg_clk 31250000
- cpu_clk 300000000, cpm_clk 250000000, bus_clk 100000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 300 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
NIP: 1FFE8A88 XER: 00000000 LR: 1FFE89CC REGS: 1ffa1df0 TRAP: 0700 DAR: 00000000
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 00729878 1FFA1EE0 EFFFFFFF 28EE0928 1FFAB424 00006BC4 1FFA201D 3D313135
GPR08: 1FFF0314 00000000 0028EE09 E6635C01 1FFA1CB0 FFF7FEFF 1FFFE000 DFFD2000
GPR16: 1FFF6E00 00000000 00000000 00000000 00003002 00000001 00000000 1FFD5098
GPR24: 1FFD57D4 01000000 1FFA1F20 00000000 1FFA2008 1FFA1F6C 1FFFEB88 1FFF715C
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 27 2009 - 17:27:10)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 3x, VCO Div 4, 60x Bus Freq 16-50 , Core Freq 50-150
- dfbrg 1, corecnf 0x10, busdf 4, cpmdf 1, plldf 0, pllmf 4, pcidf 3
- vco_out 500000000, scc_clk 125000000, brg_clk 31250000
- cpu_clk 300000000, cpm_clk 250000000, bus_clk 100000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 300 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
it hangs here only....if i do manual hardware reset it hangs in DRAM : 512MB as below
U-Boot 1.3.1 (Jul 27 2009 - 17:27:10)
MPC8260 Reset Status: External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 3x, VCO Div 4, 60x Bus Freq 16-50 , Core Freq 50-150
- dfbrg 1, corecnf 0x10, busdf 4, cpmdf 1, plldf 0, pllmf 4, pcidf 3
- vco_out 500000000, scc_clk 125000000, brg_clk 31250000
- cpu_clk 300000000, cpm_clk 250000000, bus_clk 100000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 300 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
it hangs here only if i press manual hardware reset many times also.
if i power off & switch on then it reboots in normal way again.
>
>>>> i have checked the SDRAM configuration settings everything is fine as per the device datasheet.
>>>>
>>>> please i want to know where is the problem, what is the cause for this exception. why memory test fails after 40-60mins.
>>>>
>>>> error output is as attached:-
>>>>
>>>> MPC8260 Reset Status: Check Stop, External Soft, External Hard
>>>>
>>>> MPC8260 Clock Configuration
>>>> ?- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq ?20-60 ,?Core Freq 100-300
>>>> ?- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
>>>> ?- vco_out ?528000000, scc_clk ?132000000, brg_clk ? 33000000
>>>> ?- cpu_clk ?330000000, cpm_clk ?264000000, bus_clk ? 66000000
>>>>
>>>> CPU: ? MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
>>>> Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
>>>> I2C: ? ready
>>>> DRAM: ?512 MB
>>>> FLASH: 256.5 MB
>
>If this is one chip, are there really 256,5 MB ?
>
>>>> *** Warning - bad CRC, using default environment
>>>>
>>>> NIP: 1FFE8A30 XER: 00000000 LR: 1FFE899CC REGS: 1ffa1df0 TRAP: 0700 DAR: 00000000
>>>> MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
>>>>
>>>> GPR00: 446BA781 1FFA1EE0 EFFFFFFF 3A858DD6 1FFA9F3C 000080C4 1FFA201D 3D313135
>>>> GPR08: 1FFF0314 NIP: 1FFE9648 XER: 20000000 LR: 1FFE93DC REGS: 1ffa1a68 TRAP: 0700 DAR: 00000000
>>>> MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
>>>>
>>>> GPR00: 00000030 1FFA1B58 EFFFFFFF 1FFA1C1C 00000000 00000010 FFFFFFFF 00000030
>>>> GPR08: 00000041 00000000 00000000 00000002 1FFA1B60 FFF7FEFF 1FFFE000 DFFD2000
>>>> GPR16: 1FFF1240 1FFF1214 1FFF127C 1FFA1EA0 00003002 1FFA1DE0 1FFF47F8 1FFA1BD0
>>>> GPR24: 1FFA1C14 00000041 1FFF094C 00000000 1FFF47A8 1FFA1F6C 1FFF$EBBC FFFFFFFF
>>>> Call backtraace:
>>>> Program Check Exception
>>> I cannot see here in this log, where you typed mtest ...
>>
>> please see the attachment in this mail.i have captured the log file from hyper terminal.
>
>Hmm.. I looked in the log. Is this right, that if you get this error
>u-boot never returns to the shell prompt?
>
>Also from your log:
>Pattern 0000158A ?Writing... ? ? ? ? ? ?Reading...
>Mem error @ 0x0071E65C: found 00008F3F, expected 00008F21
> ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?^^ ? ? ? ? ? ? ? ? ^^
>
>Pattern FFFFEA75 ?Writing... ? ? ? ? ? ?Reading...
>Mem error @ 0x00723684: found FFFF5CB6, expected FFFF5CD4
> ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?^^ ? ? ? ? ? ? ? ? ^^
> ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?always the last byte seems broken
>
>Is there getting something hot and the board, and maybe disturb this datalines?
>
>bye
>Heiko
>--
>DENX Software Engineering GmbH, ? ? MD: Wolfgang Denk & Detlev Zundel
>HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] U-boot hangs in mtest in MPC8280 Board
2009-07-30 11:33 [U-Boot] U-boot hangs in mtest in MPC8280 Board GurumurthyGowdar
@ 2009-07-30 12:12 ` Heiko Schocher
2009-07-30 12:23 ` Jerry Van Baren
1 sibling, 0 replies; 12+ messages in thread
From: Heiko Schocher @ 2009-07-30 12:12 UTC (permalink / raw)
To: u-boot
Hello GurumurthyGowdar,
GurumurthyGowdar wrote:
> On Thu, 30 Jul 2009 16:14:30 +0530 wrote
>> Hello GurumurthyGowdar,
>>
>> GurumurthyGowdar wrote:
>>> On Thu, 30 Jul 2009 12:54:31 +0530 wrote
>>>> Hello GurumurthyGowdar,
>>>>
>>>> GurumurthyGowdar wrote:
>>>>> i am using MPC8280 in our board which has 512MB of SDRAM i.e. from micron.
>>>> Is this board in mainline, so I can look in the Source Code?
>>> yes this board is in mainline.only one board.
>> And which board is it? means ? it is MPC8280 based board called remote I/O board
How do you compile it?
make xxx_config
What is xxx for you?
I looked in code but couldn;t find a "SLN Technologies" string ...
>> As I saw in your log, it uses the "normal" mtest. Try to use
>>
>> CONFIG_SYS_ALT_MEMTEST
> how to use this...where to add...command for this test??
You just have to add this define in your board config file.
I looked in 1.3.1, so you should add a
#define CFG_ALT_MEMTEST 1
>> instead. (Hopefully, this is available in 1.3.1 ...)
>>
>>>> Which u-boot version?
>>> U-boot version is 1.3.1.
>> Hmm.. this is very old ...
> which is the latest version of u-boot ,can i upgrade the current version of u-boot to latest version i.e. from u-boot 1.3.1 to latest u-boot without reinstalling ELDK
http://git.denx.de/?p=u-boot.git;a=summary
>>>> Which SDRAMs?
>>> SDRAM is MT48LC32M16A2 from Micron.
>>>>> when i give command mtest only for 1MB to check memory test from U-boot, machine check and program exception is coming after 40 - 60mins later it hangs giving program check exception
>>>> Hmm... maybe problems with your SDRAMs?
>>> if it is SDRAM problem it should not work for 1hour also i think.
>> Why not?
> ok
>>>> Is this error shown always after 40-60 mins, not sometimes also earlier?
>>> maximum i am able to run mtest for 1hr 30 mins. sometimes it hangs with 45mins also.
>> Not earlier?
> sometimes earlier but rare
>> Hmm...
>>
>>>> Can you boot a Linux Kernel for example?
>>> No. our job is to only give the board with U-boot boot loader, Linux booting is done by our client.
>> But you can try it ...
>> This would help here, to stress more the SDRAMs ... also you
>> can do better memtests there/with it.
>
> i got one new error which is below :-
> U-Boot 1.3.1 (Jul 27 2009 - 17:27:10)
>
[...]
> DRAM: 512 MB
>
> it hangs here only if i press manual hardware reset many times also.
>
> if i power off & switch on then it reboots in normal way again.
Hmm... nothing spring to my mind, just the "standard" things:
check your
- HRCW
- clocks
- SDRAM
settings
bye,
Heiko
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] U-boot hangs in mtest in MPC8280 Board
2009-07-30 11:33 [U-Boot] U-boot hangs in mtest in MPC8280 Board GurumurthyGowdar
2009-07-30 12:12 ` Heiko Schocher
@ 2009-07-30 12:23 ` Jerry Van Baren
1 sibling, 0 replies; 12+ messages in thread
From: Jerry Van Baren @ 2009-07-30 12:23 UTC (permalink / raw)
To: u-boot
GurumurthyGowdar wrote:
>
> On Thu, 30 Jul 2009 16:14:30 +0530 wrote
>> Hello GurumurthyGowdar,
[snip]
> i got one new error which is below :-
> U-Boot 1.3.1 (Jul 27 2009 - 17:27:10)
>
> MPC8260 Reset Status: Check Stop, External Soft, External Hard
>
> MPC8260 Clock Configuration
> - Bus-to-Core Mult 3x, VCO Div 4, 60x Bus Freq 16-50 , Core Freq 50-150
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
WHAT IS YOUR BUS FREQUENCY?
WHAT IS YOUR CORE FREQUENCY?
WHY DO THE NUMBERS THE ABOVE NOT MATCH THE ONES BELOW?
> - dfbrg 1, corecnf 0x10, busdf 4, cpmdf 1, plldf 0, pllmf 4, pcidf 3
> - vco_out 500000000, scc_clk 125000000, brg_clk 31250000
> - cpu_clk 300000000, cpm_clk 250000000, bus_clk 100000000
^^^^^^^^^^^^^^^^^^ ^^^^^^^^^^^^^^^^^^
300MHz >> 15-150MHz
100MHz >> 16-50MHz
The MPC8260 has different configuration options to compensate (I
presume) for hardware clocking delays, etc. when it is run fast vs.
slow. If you have your CPU misconfigured for running at a slow speed
but actually clocking fast, I would expect your CPU and bus will be flaky.
IIRC (it's been a while), you need to read the reset section of the
User's Manual and make sure your Hardware Reset Configuration Word and
configuration strapping pins are correct for the clocking you are using.
> CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 300 MHz
> Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
> I2C: ready
> DRAM: 512 MB
> FLASH: 256.5 MB
> *** Warning - bad CRC, using default environment
>
> NIP: 1FFE8A88 XER: 00000000 LR: 1FFE89CC REGS: 1ffa1df0 TRAP: 0700 DAR: 00000000
> MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
>
> GPR00: 00729878 1FFA1EE0 EFFFFFFF 28EE0928 1FFAB424 00006BC4 1FFA201D 3D313135
> GPR08: 1FFF0314 00000000 0028EE09 E6635C01 1FFA1CB0 FFF7FEFF 1FFFE000 DFFD2000
> GPR16: 1FFF6E00 00000000 00000000 00000000 00003002 00000001 00000000 1FFD5098
> GPR24: 1FFD57D4 01000000 1FFA1F20 00000000 1FFA2008 1FFA1F6C 1FFFEB88 1FFF715C
> Call backtrace:
> Program Check Exception
Hmmm, CPU and bus flaky.
[snip]
Best regards,
gvb
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] U-boot hangs in mtest in MPC8280 Board
@ 2009-07-31 7:10 GurumurthyGowdar
2009-07-31 7:45 ` Wolfgang Denk
0 siblings, 1 reply; 12+ messages in thread
From: GurumurthyGowdar @ 2009-07-31 7:10 UTC (permalink / raw)
To: u-boot
On Thu, 30 Jul 2009 20:07:46 +0530 wrote
>GurumurthyGowdar wrote:
>>
>> On Thu, 30 Jul 2009 16:14:30 +0530 ?wrote
>>> Hello GurumurthyGowdar,
>
>[snip]
>
>> i got one new error which is below :-
>> U-Boot 1.3.1 (Jul 27 2009 - 17:27:10)
>>
>> MPC8260 Reset Status: Check Stop, External Soft, External Hard
>>
>> MPC8260 Clock Configuration
>> ?- Bus-to-Core Mult 3x, VCO Div 4, 60x Bus Freq ?16-50 ,?Core Freq ?50-150
> ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
>WHAT IS YOUR BUS FREQUENCY?
>WHAT IS YOUR CORE FREQUENCY?
>WHY DO THE NUMBERS THE ABOVE NOT MATCH THE ONES BELOW?
>
>> ?- dfbrg 1, corecnf 0x10, busdf 4, cpmdf 1, plldf 0, pllmf 4, pcidf 3
>> ?- vco_out ?500000000, scc_clk ?125000000, brg_clk ? 31250000
>> ?- cpu_clk ?300000000, cpm_clk ?250000000, bus_clk ?100000000
> ? ? ?^^^^^^^^^^^^^^^^^^ ? ? ? ? ? ? ? ? ? ? ?^^^^^^^^^^^^^^^^^^
>
>300MHz >> 15-150MHz
>100MHz >> 16-50MHz
i have configured according to MPC8280 Reference Manual. it is correct values , i have checked HRCW and MOC_CK configuration.
but when U-boot boots the values does not matching i am also surprised about this. you are saying according to MPC8260.
have anyon eported U-boot to MPC8280,let me know what configuration you have set?
>
>The MPC8260 has different configuration options to compensate (I
>presume) for hardware clocking delays, etc. when it is run fast vs.
>slow. ?If you have your CPU misconfigured for running at a slow speed
>but actually clocking fast, I would expect your CPU and bus will be flaky.
>
>IIRC (it's been a while), you need to read the reset section of the
>User's Manual and make sure your Hardware Reset Configuration Word and
>configuration strapping pins are correct for the clocking you are using.
>
>> CPU: ? MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 300 MHz
>> Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
>> I2C: ? ready
>> DRAM: ?512 MB
>> FLASH: 256.5 MB
>> *** Warning - bad CRC, using default environment
>>
>> NIP: 1FFE8A88 XER: 00000000 LR: 1FFE89CC REGS: 1ffa1df0 TRAP: 0700 DAR: 00000000
>> MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
>>
>> GPR00: 00729878 1FFA1EE0 EFFFFFFF 28EE0928 1FFAB424 00006BC4 1FFA201D 3D313135
>> GPR08: 1FFF0314 00000000 0028EE09 E6635C01 1FFA1CB0 FFF7FEFF 1FFFE000 DFFD2000
>> GPR16: 1FFF6E00 00000000 00000000 00000000 00003002 00000001 00000000 1FFD5098
>> GPR24: 1FFD57D4 01000000 1FFA1F20 00000000 1FFA2008 1FFA1F6C 1FFFEB88 1FFF715C
>> Call backtrace:
>> Program Check Exception
>
>Hmmm, CPU and bus flaky.
>
>[snip]
>
>Best regards,
>gvb
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] U-boot hangs in mtest in MPC8280 Board
2009-07-31 7:10 GurumurthyGowdar
@ 2009-07-31 7:45 ` Wolfgang Denk
0 siblings, 0 replies; 12+ messages in thread
From: Wolfgang Denk @ 2009-07-31 7:45 UTC (permalink / raw)
To: u-boot
Dear "GurumurthyGowdar",
In message <1248964666.S.4202.18697.f4mail-235-213.rediffmail.com.old.1249024209.63308@webmail.rediffmail.com> you wrote:
> --===============0249435520==
> Content-Type: multipart/alternative;
> boundary="=_735971d1aa93205218ff6547f173efbb"
>
> --=_735971d1aa93205218ff6547f173efbb
> Content-Transfer-Encoding: 7bit
> Content-Type: text/plain; charset="ISO-8859-1"
Please stop this crap. Please post plain text _only_.
> i have configured according to MPC8280 Reference Manual. it is correct values , i have checked HRCW and MOC_CK configuration.
>
> but when U-boot boots the values does not matching i am also surprised about this. you are saying according to MPC8260.
>
> have anyon eported U-boot to MPC8280,let me know what configuration you have set?
We have ported U-Boot to many MPC82xx systems and never observers any
such problems.
But of course it is ompossible to give you any recommendations as we
don't know your hardware design, and we don't know the modifications
to U-Boot you made to port it to your hardware.
Judging from waht we see here this is either a serious hardware issue,
or missing and/or incorrect initialization in U-Boot, and eventually
both in combination.
Re-read the U-Boot Porting Guide in the README and check if maybe time
has come to call out to the no_more_time() resort.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Hi there! This is just a note from me, to you, to tell you, the per-
son reading this note, that I can't think up any more famous quotes,
jokes, nor bizarre stories, so you may as well go home.
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] U-boot hangs in mtest in MPC8280 Board
@ 2009-07-30 12:53 GurumurthyGowdar
0 siblings, 0 replies; 12+ messages in thread
From: GurumurthyGowdar @ 2009-07-30 12:53 UTC (permalink / raw)
To: u-boot
On Thu, 30 Jul 2009 17:50:47 +0530 wrote
>Hello GurumurthyGowdar,
>
>GurumurthyGowdar wrote:
>> On Thu, 30 Jul 2009 16:14:30 +0530 ?wrote
>>> Hello GurumurthyGowdar,
>>>
>>> GurumurthyGowdar wrote:
>>>> On Thu, 30 Jul 2009 12:54:31 +0530 ?wrote
>>>>> Hello GurumurthyGowdar,
>>>>>
>>>>> GurumurthyGowdar wrote:
>>>>>> i am using MPC8280 in our board which has 512MB of SDRAM i.e. from micron.
>>>>> Is this board in mainline, so I can look in the Source Code?
>>>> yes this board is in mainline.only one board.
>>> And which board is it? means ? it is MPC8280 based board called remote I/O board
>
>How do you compile it?
>
>make xxx_config
>
>What is xxx for you?
>I looked in code but couldn;t find a "SLN Technologies" string ...
>
>>> As I saw in your log, it uses the "normal" mtest. Try to use
>>>
>>> CONFIG_SYS_ALT_MEMTEST
>> how to use this...where to add...command for this test??
>
>You just have to add this define in your board config file.
>I looked in 1.3.1, so you should add a
>
>#define CFG_ALT_MEMTEST ? ? ? ? 1
i have added this line. after adding this which command i have to give..same mtest or any other command for CFG_ALT_MEMTEST ??
>
>>> instead. (Hopefully, this is available in 1.3.1 ...)
>>>
>>>>> Which u-boot version?
>>>> U-boot version is 1.3.1.
>>> Hmm.. this is very old ...
>> which is the latest version of u-boot ,can i upgrade the current version of u-boot to latest version i.e. from u-boot 1.3.1 to latest u-boot without reinstalling ELDK
>
>http://git.denx.de/?p=u-boot.git;a=summary
>
>>>>> Which SDRAMs?
>>>> SDRAM is MT48LC32M16A2 from Micron.
>>>>>> when i give command mtest ?only for 1MB to check memory test from U-boot, machine check and program exception is coming after 40 - 60mins later it hangs giving program check exception
>>>>> Hmm... maybe problems with your SDRAMs?
>>>> if it is SDRAM problem it should not work for 1hour also i think.
>>> Why not?
>> ok
>>>>> Is this error shown always after 40-60 mins, not sometimes also earlier?
>>>> maximum i am able to run mtest for 1hr 30 mins. sometimes it hangs with 45mins also.
>>> Not earlier?
>> sometimes earlier but rare
>>> Hmm...
>>>
>>>>> Can you boot a Linux Kernel for example?
>>>> No. our job is to only give the board with U-boot boot loader, Linux booting is done by our client.
>>> But you can try it ...
>>> This would help here, to stress more the SDRAMs ... also you
>>> can do better memtests there/with it.
>>
>> i got one new error which is below :-
>> U-Boot 1.3.1 (Jul 27 2009 - 17:27:10)
>>
>[...]
>> DRAM: ?512 MB
>>
>> it hangs here only if i press manual hardware reset many times also.
>>
>> if i power off & switch on then it reboots in normal way again.
>
>Hmm... nothing spring to my mind, just the "standard" things:
>
>check your
>- HRCW
>- clocks
>- SDRAM
>settings
>
>bye,
>Heiko
>--
>DENX Software Engineering GmbH, ? ? MD: Wolfgang Denk & Detlev Zundel
>HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] U-boot hangs in mtest in MPC8280 Board
@ 2009-07-30 11:32 GurumurthyGowdar
0 siblings, 0 replies; 12+ messages in thread
From: GurumurthyGowdar @ 2009-07-30 11:32 UTC (permalink / raw)
To: u-boot
On Thu, 30 Jul 2009 16:14:30 +0530 wrote
>Hello GurumurthyGowdar,
>
>GurumurthyGowdar wrote:
>> On Thu, 30 Jul 2009 12:54:31 +0530 ?wrote
>>> Hello GurumurthyGowdar,
>>>
>>> GurumurthyGowdar wrote:
>>>> i am using MPC8280 in our board which has 512MB of SDRAM i.e. from micron.
>>> Is this board in mainline, so I can look in the Source Code?
>> yes this board is in mainline.only one board.
>
>And which board is it? means ? it is MPC8280 based board called remote I/O board
>As I saw in your log, it uses the "normal" mtest. Try to use
>
>CONFIG_SYS_ALT_MEMTEST
how to use this...where to add...command for this test??
>
>instead. (Hopefully, this is available in 1.3.1 ...)
>
>>> Which u-boot version?
>> U-boot version is 1.3.1.
>
>Hmm.. this is very old ...
which is the latest version of u-boot ,can i upgrade the current version of u-boot to latest version i.e. from u-boot 1.3.1 to latest u-boot without reinstalling ELDK
>
>>> Which SDRAMs?
>> SDRAM is MT48LC32M16A2 from Micron.
>>>> when i give command mtest ?only for 1MB to check memory test from U-boot, machine check and program exception is coming after 40 - 60mins later it hangs giving program check exception
>>> Hmm... maybe problems with your SDRAMs?
>> if it is SDRAM problem it should not work for 1hour also i think.
>
>Why not?
ok
>
>>> Is this error shown always after 40-60 mins, not sometimes also earlier?
>> maximum i am able to run mtest for 1hr 30 mins. sometimes it hangs with 45mins also.
>
>Not earlier?
sometimes earlier but rare
>
>Hmm...
>
>>> Can you boot a Linux Kernel for example?
>> No. our job is to only give the board with U-boot boot loader, Linux booting is done by our client.
>
>But you can try it ...
>This would help here, to stress more the SDRAMs ... also you
>can do better memtests there/with it.
i got one new error which is below :-
U-Boot 1.3.1 (Jul 27 2009 - 17:27:10)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 3x, VCO Div 4, 60x Bus Freq 16-50 , Core Freq 50-150
- dfbrg 1, corecnf 0x10, busdf 4, cpmdf 1, plldf 0, pllmf 4, pcidf 3
- vco_out 500000000, scc_clk 125000000, brg_clk 31250000
- cpu_clk 300000000, cpm_clk 250000000, bus_clk 100000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 300 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
NIP: 1FFE8A88 XER: 00000000 LR: 1FFE89CC REGS: 1ffa1df0 TRAP: 0700 DAR: 00000000
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 00729878 1FFA1EE0 EFFFFFFF 28EE0928 1FFAB424 00006BC4 1FFA201D 3D313135
GPR08: 1FFF0314 00000000 0028EE09 E6635C01 1FFA1CB0 FFF7FEFF 1FFFE000 DFFD2000
GPR16: 1FFF6E00 00000000 00000000 00000000 00003002 00000001 00000000 1FFD5098
GPR24: 1FFD57D4 01000000 1FFA1F20 00000000 1FFA2008 1FFA1F6C 1FFFEB88 1FFF715C
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 27 2009 - 17:27:10)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 3x, VCO Div 4, 60x Bus Freq 16-50 , Core Freq 50-150
- dfbrg 1, corecnf 0x10, busdf 4, cpmdf 1, plldf 0, pllmf 4, pcidf 3
- vco_out 500000000, scc_clk 125000000, brg_clk 31250000
- cpu_clk 300000000, cpm_clk 250000000, bus_clk 100000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 300 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
Caused by (from msr): Machine check in kernel mode.
it hangs here only....if i do manual hardware reset it hangs in DRAM : 512MB as below
U-Boot 1.3.1 (Jul 27 2009 - 17:27:10)
MPC8260 Reset Status: External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 3x, VCO Div 4, 60x Bus Freq 16-50 , Core Freq 50-150
- dfbrg 1, corecnf 0x10, busdf 4, cpmdf 1, plldf 0, pllmf 4, pcidf 3
- vco_out 500000000, scc_clk 125000000, brg_clk 31250000
- cpu_clk 300000000, cpm_clk 250000000, bus_clk 100000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 300 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
it hangs here only if i press manual hardware reset many times also.
if i power off & switch on then it reboots in normal way again.
>
>>>> i have checked the SDRAM configuration settings everything is fine as per the device datasheet.
>>>>
>>>> please i want to know where is the problem, what is the cause for this exception. why memory test fails after 40-60mins.
>>>>
>>>> error output is as attached:-
>>>>
>>>> MPC8260 Reset Status: Check Stop, External Soft, External Hard
>>>>
>>>> MPC8260 Clock Configuration
>>>> ?- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq ?20-60 ,?Core Freq 100-300
>>>> ?- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
>>>> ?- vco_out ?528000000, scc_clk ?132000000, brg_clk ? 33000000
>>>> ?- cpu_clk ?330000000, cpm_clk ?264000000, bus_clk ? 66000000
>>>>
>>>> CPU: ? MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
>>>> Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
>>>> I2C: ? ready
>>>> DRAM: ?512 MB
>>>> FLASH: 256.5 MB
>
>If this is one chip, are there really 256,5 MB ?
>
>>>> *** Warning - bad CRC, using default environment
>>>>
>>>> NIP: 1FFE8A30 XER: 00000000 LR: 1FFE899CC REGS: 1ffa1df0 TRAP: 0700 DAR: 00000000
>>>> MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
>>>>
>>>> GPR00: 446BA781 1FFA1EE0 EFFFFFFF 3A858DD6 1FFA9F3C 000080C4 1FFA201D 3D313135
>>>> GPR08: 1FFF0314 NIP: 1FFE9648 XER: 20000000 LR: 1FFE93DC REGS: 1ffa1a68 TRAP: 0700 DAR: 00000000
>>>> MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
>>>>
>>>> GPR00: 00000030 1FFA1B58 EFFFFFFF 1FFA1C1C 00000000 00000010 FFFFFFFF 00000030
>>>> GPR08: 00000041 00000000 00000000 00000002 1FFA1B60 FFF7FEFF 1FFFE000 DFFD2000
>>>> GPR16: 1FFF1240 1FFF1214 1FFF127C 1FFA1EA0 00003002 1FFA1DE0 1FFF47F8 1FFA1BD0
>>>> GPR24: 1FFA1C14 00000041 1FFF094C 00000000 1FFF47A8 1FFA1F6C 1FFF$EBBC FFFFFFFF
>>>> Call backtraace:
>>>> Program Check Exception
>>> I cannot see here in this log, where you typed mtest ...
>>
>> please see the attachment in this mail.i have captured the log file from hyper terminal.
>
>Hmm.. I looked in the log. Is this right, that if you get this error
>u-boot never returns to the shell prompt?
>
>Also from your log:
>Pattern 0000158A ?Writing... ? ? ? ? ? ?Reading...
>Mem error @ 0x0071E65C: found 00008F3F, expected 00008F21
> ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?^^ ? ? ? ? ? ? ? ? ^^
>
>Pattern FFFFEA75 ?Writing... ? ? ? ? ? ?Reading...
>Mem error @ 0x00723684: found FFFF5CB6, expected FFFF5CD4
> ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?^^ ? ? ? ? ? ? ? ? ^^
> ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?always the last byte seems broken
>
>Is there getting something hot and the board, and maybe disturb this datalines?
>
>bye
>Heiko
>--
>DENX Software Engineering GmbH, ? ? MD: Wolfgang Denk & Detlev Zundel
>HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
>
^ permalink raw reply [flat|nested] 12+ messages in thread
[parent not found: <1248938671.S.4267.18003.f4mail-235-141.rediffmail.com.old.1248945071.40438@webmail.rediffmail.com>]
* [U-Boot] U-boot hangs in mtest in MPC8280 Board
[not found] <1248938671.S.4267.18003.f4mail-235-141.rediffmail.com.old.1248945071.40438@webmail.rediffmail.com>
@ 2009-07-30 10:51 ` Heiko Schocher
0 siblings, 0 replies; 12+ messages in thread
From: Heiko Schocher @ 2009-07-30 10:51 UTC (permalink / raw)
To: u-boot
Hello GurumurthyGowdar,
GurumurthyGowdar wrote:
> On Thu, 30 Jul 2009 12:54:31 +0530 wrote
>> Hello GurumurthyGowdar,
>>
>> GurumurthyGowdar wrote:
>>> i am using MPC8280 in our board which has 512MB of SDRAM i.e. from micron.
>> Is this board in mainline, so I can look in the Source Code?
> yes this board is in mainline.only one board.
And which board is it?
As I saw in your log, it uses the "normal" mtest. Try to use
CONFIG_SYS_ALT_MEMTEST
instead. (Hopefully, this is available in 1.3.1 ...)
>> Which u-boot version?
> U-boot version is 1.3.1.
Hmm.. this is very old ...
>> Which SDRAMs?
> SDRAM is MT48LC32M16A2 from Micron.
>>> when i give command mtest only for 1MB to check memory test from U-boot, machine check and program exception is coming after 40 - 60mins later it hangs giving program check exception
>> Hmm... maybe problems with your SDRAMs?
> if it is SDRAM problem it should not work for 1hour also i think.
Why not?
>> Is this error shown always after 40-60 mins, not sometimes also earlier?
> maximum i am able to run mtest for 1hr 30 mins. sometimes it hangs with 45mins also.
Not earlier?
Hmm...
>> Can you boot a Linux Kernel for example?
> No. our job is to only give the board with U-boot boot loader, Linux booting is done by our client.
But you can try it ...
This would help here, to stress more the SDRAMs ... also you
can do better memtests there/with it.
>>> i have checked the SDRAM configuration settings everything is fine as per the device datasheet.
>>>
>>> please i want to know where is the problem, what is the cause for this exception. why memory test fails after 40-60mins.
>>>
>>> error output is as attached:-
>>>
>>> MPC8260 Reset Status: Check Stop, External Soft, External Hard
>>>
>>> MPC8260 Clock Configuration
>>> - Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
>>> - dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
>>> - vco_out 528000000, scc_clk 132000000, brg_clk 33000000
>>> - cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
>>>
>>> CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
>>> Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
>>> I2C: ready
>>> DRAM: 512 MB
>>> FLASH: 256.5 MB
If this is one chip, are there really 256,5 MB ?
>>> *** Warning - bad CRC, using default environment
>>>
>>> NIP: 1FFE8A30 XER: 00000000 LR: 1FFE899CC REGS: 1ffa1df0 TRAP: 0700 DAR: 00000000
>>> MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
>>>
>>> GPR00: 446BA781 1FFA1EE0 EFFFFFFF 3A858DD6 1FFA9F3C 000080C4 1FFA201D 3D313135
>>> GPR08: 1FFF0314 NIP: 1FFE9648 XER: 20000000 LR: 1FFE93DC REGS: 1ffa1a68 TRAP: 0700 DAR: 00000000
>>> MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
>>>
>>> GPR00: 00000030 1FFA1B58 EFFFFFFF 1FFA1C1C 00000000 00000010 FFFFFFFF 00000030
>>> GPR08: 00000041 00000000 00000000 00000002 1FFA1B60 FFF7FEFF 1FFFE000 DFFD2000
>>> GPR16: 1FFF1240 1FFF1214 1FFF127C 1FFA1EA0 00003002 1FFA1DE0 1FFF47F8 1FFA1BD0
>>> GPR24: 1FFA1C14 00000041 1FFF094C 00000000 1FFF47A8 1FFA1F6C 1FFF$EBBC FFFFFFFF
>>> Call backtraace:
>>> Program Check Exception
>> I cannot see here in this log, where you typed mtest ...
>
> please see the attachment in this mail.i have captured the log file from hyper terminal.
Hmm.. I looked in the log. Is this right, that if you get this error
u-boot never returns to the shell prompt?
Also from your log:
Pattern 0000158A Writing... \b\b\b\b\b\b\b\b\b\bReading...
Mem error @ 0x0071E65C: found 00008F3F, expected 00008F21
^^ ^^
Pattern FFFFEA75 Writing... \b\b\b\b\b\b\b\b\b\bReading...
Mem error @ 0x00723684: found FFFF5CB6, expected FFFF5CD4
^^ ^^
always the last byte seems broken
Is there getting something hot and the board, and maybe disturb this datalines?
bye
Heiko
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] U-boot hangs in mtest in MPC8280 Board
@ 2009-07-30 10:08 GurumurthyGowdar
0 siblings, 0 replies; 12+ messages in thread
From: GurumurthyGowdar @ 2009-07-30 10:08 UTC (permalink / raw)
To: u-boot
On Thu, 30 Jul 2009 15:19:13 +0530 wrote
>
>
>On Thu, 30 Jul 2009 14:41:13 +0530 ?wrote
>>
>>
>>
>>
>>On Thu, 30 Jul 2009 12:54:31 +0530 ?wrote
>>>Hello GurumurthyGowdar,
>>>
>>>GurumurthyGowdar wrote:
>>>> i am using MPC8280 in our board which has 512MB of SDRAM i.e. from micron.
>>>
>>>Is this board in mainline, so I can look in the Source Code?
>>yes this board is in mainline.only one board.
>>
>>>Which u-boot version?
>>U-boot version is 1.3.1.
>>
>>>Which SDRAMs?
>>SDRAM is MT48LC32M16A2 from Micron.
>>>
>>>> when i give command mtest ?only for 1MB to check memory test from U-boot, machine check and program exception is coming after 40 - 60mins later it hangs giving program check exception
>>>
>>>Hmm... maybe problems with your SDRAMs?
>>if it is SDRAM problem it should not work for 1hour also i think.
>>
>>>Is this error shown always after 40-60 mins, not sometimes also earlier?
>>maximum i am able to run mtest for 1hr 30 mins. sometimes it hangs with 45mins also.
>>
>>>Can you boot a Linux Kernel for example?
>>No. our job is to only give the board with U-boot boot loader, Linux booting is done by our client.
>>>
>>>> i have checked the SDRAM configuration settings everything is fine as per the device datasheet.
>>>>
>>>> please i want to know where is the problem, what is the cause for this exception. why memory test fails after 40-60mins.
>>>>
>>>> error output is as attached:-
>>>>
>U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
>
>MPC8260 Reset Status: External Soft, External Hard
>
>MPC8260 Clock Configuration
> - Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq ?20-60 ,?Core Freq 100-300
> - dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
> - vco_out ?528000000, scc_clk ?132000000, brg_clk ? 33000000
> - cpu_clk ?330000000, cpm_clk ?264000000, bus_clk ? 66000000
>
>CPU: ? MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
>Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
>I2C: ? ready
>DRAM: ?512 MB
>FLASH: 256.5 MB
>*** Warning - bad CRC, using default environment
>
>In: ? ?serial
>Out: ? serial
>Err: ? serial
>Net: ? FCC2 ETHERNET
>RIO->mtest 0x00700000 0x00800000
>
>
>Pattern 00000000 ?Writing... ? ? ? ? ? ?Reading...
>Pattern FFFFFFFF ?Writing... ? ? ? ? ? ?Reading...
>Mem error @ 0x0071E65C: found 00008F3F, expected 00008F21
>
>Pattern FFFFEA75 ?Writing... ? ? ? ? ? ?Reading...
>Mem error @ 0x00723684: found FFFF5CB6, expected FFFF5CD4
>
>Pattern 0000158B ?Writing... ? ? ? ? ? ?Reading...
>Pattern FFFFEA74 ?Writing... ? ? ? ? ? ?Reading...
>Pattern 0000158C ?Writing... ? ? ? ? ? ?Reading...
>Pattern FFFFEA73 ?Writing... ? ? ? ? ? ?NIP: 1FFA1F70 XER: 20000000 LR: 1FFA1F6C REGS: 1ffa1cf8 TRAP: 0700 DAR: 00000000
>MSR: 0008b002 EE: 1 PR: 0 FP: 1 ME: 1 IR/DR: 00
>
>GPR00: 1FFA1F6C 1FFA1DE8 EFFFFFFF 00000000 00000000 00000010 1FFF6E08 00000000
>GPR08: 00000000 FFFFFFD0 00000000 00000000 1FFA1B78 FFF7FEFF 1FFFE000 1FFF44B8
>GPR16: 1FFF6E08 00000000 00000000 00000000 1FFF32D0 1FFF32F8 1FFF32FC 1FFF3308
>GPR24: FFFFFFFF 00000000 00000000 00000000 1FFB2228 00000000 00000000 00000000
>Call backtrace:
>Program Check Exception
>
>
>U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
>
>MPC8260 Reset Status: Check Stop, External Soft, External Hard
>
>MPC8260 Clock Configuration
> - Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq ?20-60 ,?Core Freq 100-300
> - dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
> - vco_out ?528000000, scc_clk ?132000000, brg_clk ? 33000000
> - cpu_clk ?330000000, cpm_clk ?264000000, bus_clk ? 66000000
>
>CPU: ? MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
>Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
>I2C: ? ready
>DRAM: ?512 MB
>FLASH: 256.5 MB
>*** Warning - bad CRC, using default environment
>
>In: ? ?serial
>Out: ? serial
>Err: ? serial
>Net: ? FCC2 ETHERNET
>RIO->NIP: 1FFD5834 XER: 00000000 LR: 1FFD5834 REGS: 1fed8cbe TRAP: 0600 DAR: 1FED8DB6
>MSR: 00003002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
>
>GPR00: 1FFD5098 1FED8DAE EFFFFFFF 1FED8DD6 1FED8ECE 00005F81 1FFD5000 1FFF7208
>GPR08: 1FFF7278 F0000080 NIP: 1FFA1DCC XER: 20000000 LR: 1FFA1DCC REGS: 1fed897c TRAP: 0700 DAR: 1FED8DB6
>MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
>
>GPR00: 1FFA1DCC 1FED8A6C EFFFFFFF 00000000 1FED8AA0 00000010 FFFFFFFF 00000030
>GPR08: 00000041 F0000088 00000000 F0000091 1FED89EC FFF7FEFF 1FFFE000 1FFF44B8
>GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 1FED8CAE 00000000 1FFD5098
>GPR24: 1FFD5828 1FFA1DCC 1FFF094C 1FFF0958 1FED8AA0 1FFA1F6C 1FFFE994 1FED8CBE
>Call backtrace:
>Program Check Exception
>
>
this same thing repeats and hangs , if i press hardware reset also it hangs here.....please help me out to solve this i am not able to identify where is the problem
with regards,
gurumurthy
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] U-boot hangs in mtest in MPC8280 Board
@ 2009-07-30 9:49 GurumurthyGowdar
0 siblings, 0 replies; 12+ messages in thread
From: GurumurthyGowdar @ 2009-07-30 9:49 UTC (permalink / raw)
To: u-boot
On Thu, 30 Jul 2009 14:41:13 +0530 wrote
>
>
>
>
>On Thu, 30 Jul 2009 12:54:31 +0530 ?wrote
>>Hello GurumurthyGowdar,
>>
>>GurumurthyGowdar wrote:
>>> i am using MPC8280 in our board which has 512MB of SDRAM i.e. from micron.
>>
>>Is this board in mainline, so I can look in the Source Code?
>yes this board is in mainline.only one board.
>
>>Which u-boot version?
>U-boot version is 1.3.1.
>
>>Which SDRAMs?
>SDRAM is MT48LC32M16A2 from Micron.
>>
>>> when i give command mtest ?only for 1MB to check memory test from U-boot, machine check and program exception is coming after 40 - 60mins later it hangs giving program check exception
>>
>>Hmm... maybe problems with your SDRAMs?
>if it is SDRAM problem it should not work for 1hour also i think.
>
>>Is this error shown always after 40-60 mins, not sometimes also earlier?
>maximum i am able to run mtest for 1hr 30 mins. sometimes it hangs with 45mins also.
>
>>Can you boot a Linux Kernel for example?
>No. our job is to only give the board with U-boot boot loader, Linux booting is done by our client.
>>
>>> i have checked the SDRAM configuration settings everything is fine as per the device datasheet.
>>>
>>> please i want to know where is the problem, what is the cause for this exception. why memory test fails after 40-60mins.
>>>
>>> error output is as attached:-
>>>
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: FCC2 ETHERNET
RIO->mtest 0x00700000 0x00800000
Pattern 00000000 Writing... Reading...
Pattern FFFFFFFF Writing... Reading...
Mem error @ 0x0071E65C: found 00008F3F, expected 00008F21
Pattern FFFFEA75 Writing... \b\b\b\b\b\b\b\b\b\bReading...
Mem error @ 0x00723684: found FFFF5CB6, expected FFFF5CD4
Pattern 0000158B Writing... \b\b\b\b\b\b\b\b\b\bReading...
Pattern FFFFEA74 Writing... \b\b\b\b\b\b\b\b\b\bReading...
Pattern 0000158C Writing... \b\b\b\b\b\b\b\b\b\bReading...
Pattern FFFFEA73 Writing... \b\b\b\b\b\b\b\b\b\bNIP: 1FFA1F70 XER: 20000000 LR: 1FFA1F6C REGS: 1ffa1cf8 TRAP: 0700 DAR: 00000000
MSR: 0008b002 EE: 1 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 1FFA1F6C 1FFA1DE8 EFFFFFFF 00000000 00000000 00000010 1FFF6E08 00000000
GPR08: 00000000 FFFFFFD0 00000000 00000000 1FFA1B78 FFF7FEFF 1FFFE000 1FFF44B8
GPR16: 1FFF6E08 00000000 00000000 00000000 1FFF32D0 1FFF32F8 1FFF32FC 1FFF3308
GPR24: FFFFFFFF 00000000 00000000 00000000 1FFB2228 00000000 00000000 00000000
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: FCC2 ETHERNET
RIO->NIP: 1FFD5834 XER: 00000000 LR: 1FFD5834 REGS: 1fed8cbe TRAP: 0600 DAR: 1FED8DB6
MSR: 00003002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 1FFD5098 1FED8DAE EFFFFFFF 1FED8DD6 1FED8ECE 00005F81 1FFD5000 1FFF7208
GPR08: 1FFF7278 F0000080 NIP: 1FFA1DCC XER: 20000000 LR: 1FFA1DCC REGS: 1fed897c TRAP: 0700 DAR: 1FED8DB6
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 1FFA1DCC 1FED8A6C EFFFFFFF 00000000 1FED8AA0 00000010 FFFFFFFF 00000030
GPR08: 00000041 F0000088 00000000 F0000091 1FED89EC FFF7FEFF 1FFFE000 1FFF44B8
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 1FED8CAE 00000000 1FFD5098
GPR24: 1FFD5828 1FFA1DCC 1FFF094C 1FFF0958 1FED8AA0 1FFA1F6C 1FFFE994 1FED8CBE
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
NIP: 1FFE8A30 XMSR: 83002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 6A43C291 1FFA1EEE0 %lX 5B125912 1FFA96DC 000089924 1FFA201D 3D313135
GPR08: 1FFF0314 00000000 005B1259 00000000 1FFA1CB0 FFF7FEFF 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 00000001 00000000 1FFD5098
GPR24: 1FFD57D4 1FFA1DCC 1FFA1F20 NIP: 1FFE9648 XER: 20000000 LR: 1FFE93DC REGS: 1ffa1a68 TRAP: 0700 DAR: 00000000
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 00000030 1FFA1B58 EFFFFFFF 1FFA1C1C 00000000 00000010 FFFFFFFF 00000030
GPR08: 00000041 00000000 00000000 00000002 1FFA1B60 FFF7FEFF 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 1FFdA1DE0 1FFF47F8 1FFA1BD0
GPR24: 1FFA1C14 00000041 1FFF094C 00000000 1FFF47A8 1FFA1F6C 1FFFEBBC FFFFFFFF
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
Machine check in kernel mode.
Caused by (from msr): regs 1ffa1df0 Unknown values in msr
NIPMSR: 00003000 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 00000000 1FFA1EE0 EFFFFFFF 7FBF7FFF 0000003D 0000000C 1FFA201D
GPR08: 1FFF0314 1FFA200C 008639FF 1FFF0314 1FFA1CB0 FFF7FEFF 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 1FFA1FB4 1FFB2010 00000010 3FF92CD0
GPR24: 1FFF7154 0000000C 7FBF7FFF 0000FFFF 00000000 1FFA1FF6C 41B8E8D8 10080000
Call backtrace:
machine check
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
NIP: 1FFE8A58 XER: 00000000 LRR: 1FFE89CC REGS: 1ffa1df0 TRAP: 0700 DAR: 00000000
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 007F45CB 1FFA1EE0 EFFFFFFF 37656F?EC 1FFA8D64 0000929C 3D313135
GPR08: 1FFF0314 00000000 0037656F 7F6A0DBB 1FFA1CBB FFF7FEFF 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 00000001 00000000 1FFD5098
GPR24: 1FFD587C 0000000C 1FFA1F20 00000000 1FFA2008 1FFA1F6C 1FFFEB88 1FFF715C
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
NIP: 1FFE8AA8 XER: 00000000 LR: 1FFE89CC REGS: 1ffa
1df0 TRAP: 0700 DAR: 00000000
MSR: 00083002 EE: 0 PR: 0 FP: 0x1 ME: 1 IR/DR: 00
GPR00: FB67CEE5 1FFA1EE0 EFFFFFFF C667A66C 1FFA7D2C 0000A2DC 1FFA201D 3D313135
GPR08: 1FFF0314 00000000 00C667A6 FBD44C65 1FFA1CB0 FFF7FEFF 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 00000001 00000000 1FFD5098
GPR24: 1FFD5700 0000000C 1FFA1F20 00000000 1FFA2008 1FFA1F6C 1FFFEB88 %lX
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
Machine check in kernel mode.
Caused by (from msr): regs 1ffa1df0 Unknown values in msr
NIP: 1FFE8A40 XER: 00000000 LR: 1FFE89CC REGS: 1ffa1df0 TRAP: 0200 DAR: 00000000
MSR: 00003000 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 0000A237 1FFA1EE0 EFFFFFFF 1D1527B7 1FFA35BC 0000EA4C 1FFA201D 3D313135
GPR08: 1FFF0314 1DB71064 001D1527 C23E7D6B 1FFA1CB0 FFF7FEFF 1FFFE000 cDFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 00000001 00000000 1FFD5098
GPR24: 1FFD57D4 0000000C 1FFA1F20 00000000 1FFA2008 1FFA1F6C 1FFdFEB88 1FFF715C
Call backtrace:
machine check
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
NIP: 1FFE0E78 XER: 00000000 LR: 1FFE1174 REGS: 1ffa1dd8 TRAP: 0700 DAR: 00000000
MSR: 0008b002 EE: 1 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 1FFE115C 1FFA1EC8 EFFFFFFF 1FFF0CE0 00000010 00000000 00000000 00A7880D
GPR08: 1FFD6E8C 1FFA200C 00000000 05309770 28000048 FFF7FEFF 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 00000001 00000000 1FFD5098
GPR24: 1FFF7154 1FFF7154 1FFF0CE0 0000FFFF 00000010 1FFdA1F6C 1FFFE8D8 0000001C
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
NIP: 1FFE8A30 XER: 00000000 LR: 1FFE89CC REGS: 1ffa1df0 TRAP: 0700 DAR: 00000000
MSR: %?
?\x1f?)$\x01
GPR00: DB7AB85A 1FFA1EE0 EFFFFFFF 1091813E 1FFA8F4C 000090B4 1FFA201D 3D313135
GPR08: 1FFF0314 00000000 00109181 00000000 1FFA1CB0 FFF7FEFF 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF6DD0 0000B002 00000001 00000000 1FFD5098
GPR24: 1FFD57D4 1FFF7154 1FFA1F20 00000000 1FFA2008 1FFA1F6C 1FFFEB88 1FFF715C
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: NIP: 1FFE1158 XER: 00000000 LR: 1FFE115C REGS: 1ffa1d80 TRAP: 0700 DAR: 00000000
MSR: 0008b002 EE: 1 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 1FFE41E4 1FFA1E70 EFFFFFFF 0000003E 0000002B 0000000D 1FFB2220 1FFF7298
GPR08: 1FFF7280 1FFA200C 00000DE1 1FFB2220 1FFA1D60 FFF7FEFF 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E041FFF447C 1FFF6DD0 1FFF84A8 00000001 00000000 1FFD5098
GPR24: 1FFF7154 1FFF7154 1FFF11F0 0000FFFF 00000039 1FFA1F6C 1FFFE8D8 0000003E
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
NIP: 1FFE1238 XER: 00000000 LR: 1FFE1238 REGS: 1ffa1d98 TRAP: 0700 DAR: 00000000
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 1FFE1238 1FFA1E88 EFFFFFFF 1FFA200C 00000003 1FFA1ED8 1FFB2168 FFFFFFFF
GPR08: 1FFF0314 00B2B178 00DDBA75 1FFF0314 28000048 FFF7FEFF 1FFFE000DFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C Machine check in kernel mode.
Caused by (from msr): regs 1ffa1a98 Unknown values in msr
NIP: FFFFFFFC XER: 20000000 LR: 1FFE254C REGS: 1ffa1a98 TRAP: 0200 DAR: 00000000
MSR: 00003000 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 00000004 1FFA1B88 EFFFFF2E 11FFA1BBC 1FFA1BBC 00000010 FFFFFFFF 00000030
GPR08: 00000041 FFFFFFFF 00000000 00000009 1FFA1B08 FFFF7FEFF 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 1FFA1D88 00000000 1FFD5098
GPR24: 1FFD57D4 1FFA1ED8 1FFF094C 1FFF0958 1FFA1BBC 1FFA1F6C 1FFFE994 1FFA1D98
Call backtrace:
machine check
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
NIP: 1FFE41F0 XER: 00000000 LR: 1FFE41F0 REGS: 1ffa1df0 TRAP: 0600 DAR: 1FFA1F86
MSR: 0000b002 EE: 1 PR: ? FP: 1 ME: 1 IR/DR: 00
GPR00: 1FFE115C 1FFA1EE0 EFFFFFFF 00000028 00000010 00000000 00000000 00A78817
GPR08: 1FFD6E8C 1FFA200C 00000000 05309770 28000048 FFF7FEFF 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 00000001 00000000 1FFD5098
GPR24: 1FFF7154 1FFF7154 1FFF0CD4 0000FFFF 0000001D 1FFA1F6C 1FFFE8D8 00000028
Call backtrace:
Alignment Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: FCC2 ETHERNET
RIO->NIP: 1FFD7018 XER: 00000000 LR: 1FFD7014 REGS: 1ffa1b90 TRAP: 0700 DAR: 00000000
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 1FFD5098 1FFA1C80 EFFFFFFF 1FFA1CA0 1FFF447C 00000000 1FFF8F18 1FFFF7268
GPR08: 1FFF7278 F0000080 00000002 F0000090 42000088 FFF7FEFF 1FFFE000 1FFF44B8
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 1FFA1C90 00000000 1FFD5098
GPR24: 1FFD7008 1FFA1DCC 1FFA1DC8 00000005 1FFFD658 1FFA1F6C 1FFFE994 1FFF447C
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: FCC2 ETHERNETNIP: 1FFE1158 XER: 00000000 LR: 1FFE115C REGS: 1ffa1d80 TRAP: 0700 DAR: 00000000
MSR: 0008b002 EE: 1 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 1FFE41E4 1FFA1E70 EFFFFFFF 00000002 1FFEFF91 00000006 1FFA1EA9 FFFFFFFF
GPR08: 1FFF7280 1FFA200C FFFFFFFF F0000091 1FFA1D60 FFF7FEFF 1FFFE000 1FFF0CC4
GPR16: 1FFF1240 1FFF1214 1FFF127C 1FFA1EA0 1FFF84A8 1FFF84A8 1FFEFF8C 1FFA1EAA
GPR24: 1FFF7154 1FFF7154 1FFF11D4 0000FFFF 00000000 1FFA1F6C 1FFFE8D8 00000002
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: FCC2 ETHERNET
RIO->NIP: 1FFD7018 XER: 00000000 LR: 1FFD\x10014 REGS: 1ffa1b90 TRAP: 0700 DAR: 00000000
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 1FFD5098 1FFA1C80 EFFFFFFF 1FFA1CA0 1FFF4420 00000000 1FFF8F18 1FFF7268
GPR08: 1FFF7278 F0000080 00000002 F0000090 42000088 FFF7FEFF 1FFFE000 1FFF44B8
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFFF6DD0 00003002 1FFA1C90 00000000 1FFD5098
GPR24: 1FFD7008 1FFA1DCC 1FFA1DC8 00000005 1FFFD658 1FFA1F6C 1FFFE994 1FFF447C
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: FCC2 ETHERNET
RIO->NIP: 1FFD7018 XER: 00000000 LR: 1FFD7014 REGS: 1ffa1b90 TRAP: 0700 DAR: 00000000
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 1FFdD5098 1FFA1C80 EFFFFFFF 1FFA1CA0 1FFF$4420 00000000 1FFF8F18 1FFF7268
GPR08: 1FFF7278 F00?00080 00000002 F0000090 42e000088 FFF7FEFF 1FFFE000 1FFF44B8
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 1FFA1C90 00000000 1FFD5098
GPR24: 1FFD7008 1FFA1DCC 1FFA1DC8 00000005 1FFdFD658 1FFA1F6C 1FFFE994 00000000
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
NIP: 1FFE8AA8 XER: 00000000 LR: 1FFE89CC REGS: 1ffa1d70 TRAP: 0700 DAR: 00000000
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: D5E8E58F 1FFA1E60 EFFFFFFF 0CAD0496 1FFA413C 0000DECC 1FFB2168 FFFFFFFF
GPR08: 1FFF0314 00000000 000CAD04 D56041E4 28000048 FFF7FEFF 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 1FFA1FB4 00000003 1FFA1EDC
GPR24: 1FFA1EE0 1FFA1ED8 1FFF3B9A 00000003 1FFA2008 1FFA1F6C NIP: 1FFA1EE4 XER: 20000000 LR: 1FFA1ED8 REGS: 1ffa1a70 TRAP: 0700 DAR: 00000000
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 1FFA1ED8 1FFA1B60 EFFFFFFF 00000000 1FFA1B94 00000010 FFFFFFFF 00000030
GPR08: 00000041 F0000088 00000000 F0000091 1FFA1AE0 FFF7FEFF 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 1FFA1D60 00000000 1FFD5098
GPR24: 1FFD57D4 1FFA1ED8 1FFF094C 1FFF0958 1FFA"1B94 1FFA1F6C 1FFFE99CE0CE8100
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - baad CRC, using default environment
Machine check in kernel mode.
Caused by (from msr): regs 1ffa1df0 Unknown values in msr
NIP: 1FFE8A40 XER: 00000000 LR: 1FFE89CC REGS: 1ffa1df0 TRAP: 0200 DAR: 00000000
MSR: 00003000 EE: 0 PR: 0 FP: %x MEE: 1 IR/DR: 10
GPR00: 00008140 1FFA1EE0 EFFFFFFF 455E1CD9 1FFA30A4 0000EF64 1FFA201D 3D313135
GPR08: 1FFF0314 45DF5C75 04455E1C 6B402E54 1FFA1CB0 FFF7\x10EFF 1FFFE000 DFFD2000
GPR16:1FFF2AB0 %X 1FFF6DD0 00003002 00000001 00000000 1FFD5098
GPR24: 1FFD57D4 1FFA1ED 1FFA1F20 00000000 1FFA2008 1FFA1F6C 1FFFEB88 1FFF715C
Call backtrace:
machine check
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
NIP: 1FFE41F0 XER: 00000000 LR: 1FFE41F0 REGS: 1ffa1df0 TRAP: 0600 DAR: 1FFA1F86
MSR: 0000b002 EE: 1 PR: 0 FP: 1 ME: 1 IR/DR: 000
GPR00: 1FFE115C 1FFA1EE0 EFFFFFFF 0000001B 00000000 00000000 00000000 00A7880C
GPR08: 1FFD6E8C 1FFA200C 00000000 05309770 28000048 FFF7FEFF 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 00000001 00000010 1FLFD5098
GPR24: 1FFF7154 1FFF7154 1FFF0CD4 0000FFFF 00000010 1FFA1F6C %lX 0000001B
Call backtrace:
Alignment Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: FCC2 ETHERN?TNIP: 1FFE1158 XER: 00000000 LR: 1FFE115C REGS: 1ffa1d80 TRAP: 0700 DAR: 00000000
NIP: 00000034 XER: 20000000 LR: 1FFE93DC REGS: 1ffba19f8 TRAP: 0700 DAR: 00000000
MSR: 0008b002 EE: 1 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 00000000 1FFA1AE8 EFFFFFFF 1FFA1BC8 00000001 00000010 00000001 00000030
GPR08: 00000001 Machine check in kernel mode.
Caused by (from msr): regs 1ffa16f8 Unknown values in msr
NIP: FFFFFFFC XER: 20000000 LR: 1FFE254C REGS: 1ffa16f8 TRAP: 0200 DAR: 00000000
MSR: 0000b000 EE: 1 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 00000004 1FFA17E8 EFFFFFFF 1FFA181C 1FFA181C 00000010 FFFFFFFF 00000030
GPR08: 00000041 FFFFFFFF 00000000 00000003 1FFA1768 FFF7FEFF 1FFFE000 1FFF0CC4
GPR16: 1FFF1240 1FFF1214 NIP: 00000000 XER: 20000000 LR: 00000001 REGS: 1ffa1400 TRAP: 0700 DAR: 00000000
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 00000001 1FFA"14F0 EFFFFFFF 00000000 1FFA1524 00000010 FFFFFFFF 00000030
GPR08: 00000041 F0000088 00000000 F0000091 1FFA1470 NIP: 1FFE2548 XER: 20000000 LR: 1FFE2518 REGS: 1ffa1100 TRAP: 0700 DAR: 00000000
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 00000004 1FFA11F0 EFFFFFFF 1FFA1224 1FFA1224 00000010 FFFFFFFF 00000030
GPR08: 00000041 1FFEDA08 00000000 00000009 1FFA1170 FFF7FEFF 1FFFE000 1FFF0CC4
GPR16: 1FFF1240 1FFF1214 1FFF127C 1FFA1EA0 00003002 1FFA13F0 00000000 1FFD5098
GPR24: 1FFD57D4 00000001 1FFF094C 1FFF0958 1FFA1224 1FFA1F6C 1FFFE994 1FFA1400
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
NIP: 1FFE8A30 XER: 00000000 LR: 1FFE899CC REGS: 1ffa1df0 TRAP: 0700 DAR: 00000000
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 446BA781 1FFA1EE0 EFFFFFFF 3A858DD6 1FFA9F3C 000080C4 1FFA201D 3D313135
GPR08: 1FFF0314 NIP: 1FFE9648 XER: 20000000 LR: 1FFE93DC REGS: 1ffa1a68 TRAP: 0700 DAR: 00000000
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 00000030 1FFA1B58 EFFFFFFF 1FFA1C1C 00000000 00000010 FFFFFFFF 00000030
GPR08: 00000041 00000000 00000000 00000002 1FFA1B60 FFF7FEFF 1FFFE000 DFFD2000
GPR16: 1FFF1240 1FFF1214 1FFF127C 1FFA1EA0 00003002 1FFA1DE0 1FFF47F8 1FFA1BD0
GPR24: 1FFA1C14 00000041 1FFF094C 00000000 1FFF47A8 1FFA1F6C 1FFF$EBBC FFFFFFFF
Call backtraace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: FCC2 ETHERNETNIP: 1FFE41F0 XER: 00000000 LR: 1FFE41F0 REGS: 1ffa1d70 TRAP: 0600 DAR: 1FFA1F06
MSR: 0000b002 EE: 1 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 1FFE115C 1FFA1E60 EFFFFFFF 0000004D 0000002B 00000006 FFFFFFFFF
GPR08: 1FFF7280 1FFA200C FFFFFFFF F0000091 1FFA1D60 FFF7FEFF 1FFFE000 1FFF0CC4
GPR16: 1FFF1240 1FFF1214 1FFF127C 1FFA1EA0 1FFF84A8 1FFF84A8 1FFEFF8C 1FFA1EAA
GPR24: 1FFF7154 1FFF7154 1FFF11D4 0000FFFF 00000039 NIP: 00000000 XER: 20000000 LR: 1FFE93DC REGS: 1ffa19e8 TRAP: 0700 DAR: 1FFA1F06
MSR: 0008b002 EE: 1 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 00000000 1FFA1AD8 EFFFFFFF 1FFA1B94 00000000 00000010 00000000 00000030
GPR08: 00000041 00000008 00000000 00000008 1FFA1AE0 FFF7FEFF 1FFFE000 1FFF0CC4
GPR16: 1FFF1240 1FFF1214 1FFF127C 1FFA1EA0 0000B002 1FFA1D60 1FFF47F8 1FFA1B50
GPR24: 1FFA1B94 00000041 1FFF094C 00000000 1FFF47A8 1FFA1F6C 1FFFEBBC FFFFFFFF
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
NIP: 1FFE1158 XER: 00000000 LR: 1FFE115C REGS: 1ffa1e00 TRAP: 0700 DAR: 00000000
MSR: 0008b002 EE: 1 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 1FFE41E4 1FFA1EF0 EFFFFFFF 00000023 00000010 00000000 00000000 00A7881C
GPR08: 1FFD6E8C 1FFA200C 00000000 05309770 28000048 FFF7FEFF 1FFFE02E DFFD2000
GPR16: 1FFF1240 1FFF1214 1FFF127C 1FFA1EA0 0000B002 00000001 00000000
GPR24: 1FFF7154 1FFF7154 1FFF0CE0 0000FFFF 0000001D 1FFA1F6C 1FFFE8D8 00000023
Call backtrace:
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: FCC2 ETHERNET
RIO->NIP: 1FFD5834 XER: 00000000 LR: 1FFD5834 REGS: 1ff391ee TRAP: 0600 DAR: 1FF392E6
MSR: 00003002 EE: PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 1FFD5098 1FF392DE EFFFFFFF 1FF39306 1FF393FE 00005F81 1FFD5000 1FFF7268
GPR08: 1FFF7278 F0000080 00000002 F0000090 42000080 0028EE00 1FFFE000 1FFF44B8 NIP: 1FFA1F70 XER: 20000000 LR: 1FFA1F6C REGS: 1ff38ebc TRAP: 0700 DAR: 1FF392FC
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 1FFA1F6C 1FF38FAC EFFFFFFF 00000000 1FF38FD0 00000010 FFFFFFFF FFFFFFF
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: Machine check in kernel mode.
Caused by (from msr): regs 1ffa1c38 Unknown values in msr
NIP: 1FFE2544 XER: 00000000 LR: 1FFE2518 REGS: 1ffa1c38 TRAP: 0200 DAR: 00000000
MSR: 00003000 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 00000004 1FFA1D28 EFFFFFFF 1FFA1D5C 1FFA1D5C 1FFA1D50 1FFB2168 FFFFFFFF
GPR08: 1FFEDA08 00247D29 FFFFFFFF 00000006 28000048 0028EE00 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 80000022 00000001 00000000 00003002
GPR24: 1FF38CE0 1FFF80A8 00000001 1FFB2058 1FFA1D5C 1FFA1F6C 1FFFE994 1FFB2058
Call backtrace:
machine check
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: FCC2 ETHERNETNIP: 1FFE0E78 XER: 00000000 LR: 1FFE1174 REGS: 1ffa1d58 TRAP: 0700 DAR: 00000000
MSR: 0008b002 EE: 1 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 1FFE115C 1FFA1E48 EFFFFFFF 1FFA1EAA 00000039 1FFA1E28 1FFB2220 FFFFFFFF
GPR08: 1FFF7280 1FFA200C FFFFFFFF F0000091 1FFA1D60 0028EE00 1FFFE000 1FFF0CC4
GPR16: 1FFF1240 1FFF1214 1FFF127C 1FFA1EA0 1FFF84A8 1FFF84A8 1FFEFF8C 1FFA1EAA
GPR24: 1FFF7154 1FFF7154 1FFA1EAA 0000FFFF 00000039 1FFA1F6C 1FFFE8D8 0000004D
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Machine check in kernel mode.
Caused by (from msr): regs 1ffa1df0 Unknown values in msr
NIP: 1FFE4224 XER: 00000000 LR: 1FFE41F0 REGS: 1ffa1df0 TRAP: 0200 DAR: 00000000
MSR: 0000b000 EE: 1 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 1FFE0ED8 1FFA1EE0 EFFFFFFF 000000BB 00000010 00000000 00000000 00A78827
GPR08: 1FFD6E8C 1FFA200C 00000000 05309770 28000048 0028EE00 1FFFE000 DFFD2000
GPR16: 1FFF1240 1FFF1214 1FFF127C 1FFA1EA0 0000B002 00000001 00000000 1FFD5098
GPR24: 1FFF7154 1FFF7154 1FFF7199 1FFF7198 000000FF 1FFA1F6C 1FFFE9F0 0000001C
Call backtrace:
machine check
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: FCC2 ETHERNET
RIO->NIP: 1FFD5834 XER: 00000000 LR: 1FFD5834 REGS: 1fce8076 TRAP: 0600 DAR: 1FCE816E
MSR: 00003002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 1FFD5098 1FCE8166 EFFFFFFF NIP: 00000000 XER: 20000000 LR: 1FFE93DC REGS: 1fce7cac TRAP: 0700 DAR: 1FCE816E
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 00000000 1FCE7D9C EFFFFFFF 1FCE7E58 00000000 00000010 00000000 00000030
GPR08: 00000041 00000008 00000000 00000008 1FCE7DA4 0028EE00 1FFFE000 1FFF44B8
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 1FCE8066 1FFF47F8 1FCE7E14
GPR24: 1FCE7E58 00000041 1FFF094C 00000000 1FFF47A8 1FFA1F6C 1FFFEBBC FFFFFFFF
Call backtrace:
NIP: 1FFE2548 XER: 00000000 LR: 1FFE2518 REGS: 1fce79bc TRAP: 7700 DAR: 1FCE816E
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 00000004 1FCE7AAC EFFFFFFF 1FCE7AD4 1FCE7AD4 1FCE7C0C FFFFFFFF 00000030
GPR08: 00000041 1FFEDA08 00000000 F0000091 1FCE7A1C 0028EE00 1FFFE000 1FFF44B8
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 1FCE7C9C 00000000 1FFD5098
GPR24: 1FFD57D4 00000041 1FFF094C 00000000 1FCE7AD4 1FFA1F6C 1FFFE994 FFFFFFFF
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
NIP: 1FFE0F18 XER: 00000000 LR: 1FFE0F08 REGS: 1ffa1dd8 TRAP: 0700 DAR: 00000000
MSR: 0008b002 EE: 1 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 1FFE1174 1FFA1EC8 EFFFFFFF 00000073 0000002B 00000000 00000000 00A78817
GPR08: 1FFD6E8C 1FFA200C 00000000 05309770 28000048 0028EE00 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 00000_}?7???W???_]U\x7f??????????/??/?????]W?\x7f\x0fw?7W??\x1f\x7f??01 00000000 1FFD5098
GPR24: 1FFF7154 1FFE41E4 FFFFFFFF 0000002B 00000000 1FFFA1F6C 1FFFE8D8 1FFFB199
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Machine check in kernel mode.
Caused by (from msr): regs 1ffa1d70 Unknown values in msr
NIP: 1FFE8A40 XER: 00000000 LR: 1FFE89CC REGS: 1ffa1d70 TRAP: 0200 DAR: 00000000
MSR: 00003000 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 00008E93 1FFA1E60 EFFFFFFF FB5ADF2A 1FFA5D14 0000C2F4 1FFB2168 FFFFFFFF
GPR08: 1FFF0314 FBD44C65 00FB5ADF 00C23E7D 28000048 0028EE00 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 1FFA1FB4 00000003 1FFA1EDC 1FFA200C
GPR24: 1FFA1EE0 1FFA1ED8 1FFF3BAB 00000003 1FFA2008 1FFA1F6C 1FFFEB88 1FFA2044
Call backtrace:
machine check
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: Machine check in kernel mode.
Caused by (from msr): regs 1ffa1c38 Unknown values in msr
NIP: 1FFE2544 XER: 00000000 LR: 1FFE2518 REGS: 1ffa1c38 TRAP: 0200 DAR: 00000000
MSR: 00003000 EEE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 00000004 1FFA1D28 EFFFFFFF 1FFA1D5C 1FFA1D5C 1FFA1D50 1FFB2168 FFFFFFFF
GPR08: 1FFEDA08 00247D29 FFFFFFFF 00000006 28000048 0028EE00 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 00000001 00000000 11FFD5098
GPR24: 1FFD587C 1FFF80A8 00000001 1FFB2058 1FFdA1D5C 1FFA1F6C 1FFFE994 1FFB2058
Call backtrace:
machine check
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
Machine check in kernel mode.
Caused by (from msr): reegs 1ffa1df0 Unknown values in msr
NIP: 1FFE8A40 XER: 00000000 LR: 1FFE89CC REGS: 1ffa1df0 TRAP: 0200 DAR: 00000000
MSR: 00003000 E
GPPR00: _}?7???W???_]U\x7f??????????/??/?????]W?\x7f\x0fw?7W??\x1f\x7f??42464420 00303030 20450052 3A203030 30303030 3030204C 523A2031
GPR08: 46464538 39434320 52454753 66613164 66302054 5241503A 20303230
GPR16: 30204441 523A2030 30303030 3030300A 00EE001F FFE000DF FD20001F FF2AB01F
GPR24: FF8E041F FF447C1F FFF6DD000 00300200 00000100 0000001F FD50981F FD587C1F
Call backtrace:
machhine check
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
NIP: 1FFE8AA8 XER: 00000000 LR: 1FFE89CC REGS: 1ffa1df0 TRAP: 0700 DAR: 00000000
MSR: 00083002 EE: 0 PR: 0 FP: 1
GPR00: E3A3E210 1FFA1EE0 EFFFFFFF 7FB5CF66 1FFA6094 0000BF74 1FFA201D 3D313135
GPR08: 1FFF0314 00000000 007FB5CF E3630B12 1FFA1CB0 0028EE00 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 00000001 00000000 1FFD?5098
GPR24: 1FFD5800 1FFF80A8 1FFA1F20 00000000 1FFA202E 1FFA1F6C 1FFFEB2E 1FFF715C
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Machine check in kernel mode.
Caused by (from msr): regs 1ffa1d70 Unknown values in msr
NIP: 1FFE8A40 XER: 00000000 LR: 1FFE89CC REGS: 1ffa1d70 TRAP: 0200 DAR: 00000000
MSR: 00003000 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 00006F65 1FFA1E60 EFFFFFFF B5BFAA53 1FFAF55C 00002AAC1FFB2168 FFFFFFFF
GPR08: 1FFF0314 B5D0CF31 00B5BFAA 00C23E7D 28000048 0028EE00 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E041FFF447C 1FFF6DD0 1FFA1FB4 00000003 1FFA1EDC 1FFA200C
GPR24: 1FFA1EE0 1FFA1ED8 1FFF3B9A 00000003 1FFA2008 1FFA1F6C 1FFFEB88 1FFA2028
Call backtrace:
machine check
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
Machine check in kernel mode.
Caused by (from msr): regs 1ffa1df0 Unknown values in msr
NIP: 1FFE8A40 XER: 00000000 LR: 1FFE89CC REGS: 1ffa1df0 TRAP: 0200 DAR: 00000000
MSR: 00003000 EE: 0 PR:
GPR00: 0000A712 1FFA1EE0 EFFFFFFF 181w05544 1FFA7304 0000AD04 1FFA201D 3D313135
GPR08: 1FFF0314 18B74777 00181055 00C23E7D 1FFA1CB0 0028EE00 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 00000001 00000010 1FFD5098
GPR24: 1FFD58000 1FFA1ED8 1FFA1F20 00000000 1FFA2008 1FFA1F6C 1FFFEB88 1FFF$715C
Call backtrace:
machinne check
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: NIP: 1FLFE97F8 XER: 00000000 LR: 1FFE973C REGS: 1ffa1c28 TRAP: 0700 DAR: 00000000
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 00000002 1FFA1D18 EFFFFFFF 1FFA1D64 1FFF4788 1FFdA1D58 00000000 006558038
GPR08: 1FFD6E8C 00000032 1FFF4789 00100000 F0003CD8 0028EE00 1FFFE000 DFFD2000
GPR16: 1FFF2AB0 1FFF8E04 1FFF447C 1FFF6DD0 00003002 00000001 1FFFF47F8 1FFA1D20
GPR24: 1FFA1D64 00000000 1FFA1F20 0000004D 1FFA1D64 1FFA1F6C 1FFFEBBC 1FFA1D58
Call backtrace:
Program Check Exception
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
U-Boot 1.3.1 (Jul 29 2009 - 22:41:55)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
>>>
>>> i am stuck here, dont know where to check if it hangs after 40-60mins.
>>
>>Maybe a temperature problem?
>not able to identify what is the exact problem tll now
>>
>>> do help me out in this regard,
>>
>>If I can ... share more informations, and maybe I can.
>
>please help me out if you can, let me know if any more informations required.
>>
>>bye
>>Heiko
>>--
>>DENX Software Engineering GmbH, ? ? MD: Wolfgang Denk & Detlev Zundel
>>HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
>>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] U-boot hangs in mtest in MPC8280 Board
@ 2009-07-30 6:43 GurumurthyGowdar
2009-07-30 7:31 ` Heiko Schocher
0 siblings, 1 reply; 12+ messages in thread
From: GurumurthyGowdar @ 2009-07-30 6:43 UTC (permalink / raw)
To: u-boot
Dear Sir,
i am using MPC8280 in our board which has 512MB of SDRAM i.e. from micron.
when i give command mtest only for 1MB to check memory test from U-boot, machine check and program exception is coming after 40 - 60mins later it hangs giving program check exception
i have checked the SDRAM configuration settings everything is fine as per the device datasheet.
please i want to know where is the problem, what is the cause for this exception. why memory test fails after 40-60mins.
error output is as attached:-
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
- dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
- vco_out 528000000, scc_clk 132000000, brg_clk 33000000
- cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
I2C: ready
DRAM: 512 MB
FLASH: 256.5 MB
*** Warning - bad CRC, using default environment
NIP: 1FFE8A30 XER: 00000000 LR: 1FFE899CC REGS: 1ffa1df0 TRAP: 0700 DAR: 00000000
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 446BA781 1FFA1EE0 EFFFFFFF 3A858DD6 1FFA9F3C 000080C4 1FFA201D 3D313135
GPR08: 1FFF0314 NIP: 1FFE9648 XER: 20000000 LR: 1FFE93DC REGS: 1ffa1a68 TRAP: 0700 DAR: 00000000
MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
GPR00: 00000030 1FFA1B58 EFFFFFFF 1FFA1C1C 00000000 00000010 FFFFFFFF 00000030
GPR08: 00000041 00000000 00000000 00000002 1FFA1B60 FFF7FEFF 1FFFE000 DFFD2000
GPR16: 1FFF1240 1FFF1214 1FFF127C 1FFA1EA0 00003002 1FFA1DE0 1FFF47F8 1FFA1BD0
GPR24: 1FFA1C14 00000041 1FFF094C 00000000 1FFF47A8 1FFA1F6C 1FFF$EBBC FFFFFFFF
Call backtraace:
Program Check Exception
i am stuck here, dont know where to check if it hangs after 40-60mins.
do help me out in this regard,
Thanks in advance
gurumurthy
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] U-boot hangs in mtest in MPC8280 Board
2009-07-30 6:43 GurumurthyGowdar
@ 2009-07-30 7:31 ` Heiko Schocher
0 siblings, 0 replies; 12+ messages in thread
From: Heiko Schocher @ 2009-07-30 7:31 UTC (permalink / raw)
To: u-boot
Hello GurumurthyGowdar,
GurumurthyGowdar wrote:
> i am using MPC8280 in our board which has 512MB of SDRAM i.e. from micron.
Is this board in mainline, so I can look in the Source Code?
Which u-boot version?
Which SDRAMs?
> when i give command mtest only for 1MB to check memory test from U-boot, machine check and program exception is coming after 40 - 60mins later it hangs giving program check exception
Hmm... maybe problems with your SDRAMs?
Is this error shown always after 40-60 mins, not sometimes also earlier?
Can you boot a Linux Kernel for example?
> i have checked the SDRAM configuration settings everything is fine as per the device datasheet.
>
> please i want to know where is the problem, what is the cause for this exception. why memory test fails after 40-60mins.
>
> error output is as attached:-
>
> MPC8260 Reset Status: Check Stop, External Soft, External Hard
>
> MPC8260 Clock Configuration
> - Bus-to-Core Mult 5x, VCO Div 2, 60x Bus Freq 20-60 , Core Freq 100-300
> - dfbrg 1, corecnf 0x1b, busdf 7, cpmdf 1, plldf 0, pllmf 7, pcidf 3
> - vco_out 528000000, scc_clk 132000000, brg_clk 33000000
> - cpu_clk 330000000, cpm_clk 264000000, bus_clk 66000000
>
> CPU: MPC8260 (HiP7 Rev 14, Mask 1.0 1K49M) at 330 MHz
> Board: MPC8280 Based Remote IO CARD.SLN Technologies Pvt Ltd.
> I2C: ready
> DRAM: 512 MB
> FLASH: 256.5 MB
> *** Warning - bad CRC, using default environment
>
> NIP: 1FFE8A30 XER: 00000000 LR: 1FFE899CC REGS: 1ffa1df0 TRAP: 0700 DAR: 00000000
> MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
>
> GPR00: 446BA781 1FFA1EE0 EFFFFFFF 3A858DD6 1FFA9F3C 000080C4 1FFA201D 3D313135
> GPR08: 1FFF0314 NIP: 1FFE9648 XER: 20000000 LR: 1FFE93DC REGS: 1ffa1a68 TRAP: 0700 DAR: 00000000
> MSR: 00083002 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 00
>
> GPR00: 00000030 1FFA1B58 EFFFFFFF 1FFA1C1C 00000000 00000010 FFFFFFFF 00000030
> GPR08: 00000041 00000000 00000000 00000002 1FFA1B60 FFF7FEFF 1FFFE000 DFFD2000
> GPR16: 1FFF1240 1FFF1214 1FFF127C 1FFA1EA0 00003002 1FFA1DE0 1FFF47F8 1FFA1BD0
> GPR24: 1FFA1C14 00000041 1FFF094C 00000000 1FFF47A8 1FFA1F6C 1FFF$EBBC FFFFFFFF
> Call backtraace:
> Program Check Exception
I cannot see here in this log, where you typed mtest ...
>
>
> i am stuck here, dont know where to check if it hangs after 40-60mins.
Maybe a temperature problem?
> do help me out in this regard,
If I can ... share more informations, and maybe I can.
bye
Heiko
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2009-07-31 7:45 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-07-30 11:33 [U-Boot] U-boot hangs in mtest in MPC8280 Board GurumurthyGowdar
2009-07-30 12:12 ` Heiko Schocher
2009-07-30 12:23 ` Jerry Van Baren
-- strict thread matches above, loose matches on Subject: below --
2009-07-31 7:10 GurumurthyGowdar
2009-07-31 7:45 ` Wolfgang Denk
2009-07-30 12:53 GurumurthyGowdar
2009-07-30 11:32 GurumurthyGowdar
[not found] <1248938671.S.4267.18003.f4mail-235-141.rediffmail.com.old.1248945071.40438@webmail.rediffmail.com>
2009-07-30 10:51 ` Heiko Schocher
2009-07-30 10:08 GurumurthyGowdar
2009-07-30 9:49 GurumurthyGowdar
2009-07-30 6:43 GurumurthyGowdar
2009-07-30 7:31 ` Heiko Schocher
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox