[U-Boot] [PATCH v2] TI: OMAP3: Overo Tobi ethernet support

[Tom <Tom.Rix@windriver.com>]

Olof Johansson wrote:
> Add setup for ethernet on Tobi, allowing kernel/ramdisk to be loaded
> over tftp.
> 
> Based on the omap3 evm code. I added a new highlevel define for Tobi
> to avoid having it dependent on CMD_NET (which would seem backward in
> this case).
> 
> Signed-off-by: Olof Johansson <olof@lixom.net>
> ---
> 
> This version of the patch fixes whitespace comments from WD, and includes
> fixes for the build warnings that Dirk's patch also silenced.
> 
> 
>  board/overo/overo.c           |   62 +++++++++++++++++++++++++++++++++++++++++
>  board/overo/overo.h           |   37 ++++++++++++++++++++++++
>  include/configs/omap3_overo.h |   23 ++++++++++++++-
>  3 files changed, 120 insertions(+), 2 deletions(-)
> 
> diff --git a/board/overo/overo.c b/board/overo/overo.c
> index dd6d286..7d87e52 100644
> --- a/board/overo/overo.c
> +++ b/board/overo/overo.c
> @@ -29,13 +29,19 @@
>   * MA 02111-1307 USA
>   */
>  #include <common.h>
> +#include <netdev.h>
>  #include <twl4030.h>
>  #include <asm/io.h>
>  #include <asm/arch/mux.h>
> +#include <asm/arch/mem.h>
>  #include <asm/arch/sys_proto.h>
>  #include <asm/mach-types.h>
>  #include "overo.h"
>  
> +#if defined(CONFIG_OMAP3_OVERO_TOBI)
> +static void setup_net_chip(void);
> +#endif
> +
>  /*
>   * Routine: board_init
>   * Description: Early hardware init.
> @@ -62,6 +68,10 @@ int misc_init_r(void)
>  	twl4030_power_init();
>  	twl4030_led_init();
>  
> +#if defined(CONFIG_OMAP3_OVERO_TOBI)
> +	setup_net_chip();
> +#endif
> +
>  	dieid_num_r();
>  
>  	return 0;
> @@ -76,4 +86,56 @@ int misc_init_r(void)
>  void set_muxconf_regs(void)
>  {
>  	MUX_OVERO();
> +#if defined(CONFIG_OMAP3_OVERO_TOBI)
> +	MUX_OVERO_TOBI();
> +#endif
> +}
> +
> +#if defined(CONFIG_OMAP3_OVERO_TOBI)
> +/*
> + * Routine: setup_net_chip
> + * Description: Setting up the configuration GPMC registers specific to the
> + *	      Ethernet hardware.
> + */
> +static void setup_net_chip(void)
> +{
> +	struct gpio *gpio3_base = (struct gpio *)OMAP34XX_GPIO3_BASE;
> +	struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE;
> +
> +	/* Configure GPMC registers */
> +	writel(NET_GPMC_CONFIG1, &gpmc_cfg->cs[5].config1);
> +	writel(NET_GPMC_CONFIG2, &gpmc_cfg->cs[5].config2);
> +	writel(NET_GPMC_CONFIG3, &gpmc_cfg->cs[5].config3);
> +	writel(NET_GPMC_CONFIG4, &gpmc_cfg->cs[5].config4);
> +	writel(NET_GPMC_CONFIG5, &gpmc_cfg->cs[5].config5);
> +	writel(NET_GPMC_CONFIG6, &gpmc_cfg->cs[5].config6);
> +	writel(NET_GPMC_CONFIG7, &gpmc_cfg->cs[5].config7);
> +
> +	/* Enable off mode for NWE in PADCONF_GPMC_NWE register */
> +	writew(readw(&ctrl_base ->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe);
> +	/* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */
> +	writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe);
> +	/* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */
> +	writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00,
> +		&ctrl_base->gpmc_nadv_ale);
> +
> +	/* Make GPIO 64 as output pin */
> +	writel(readl(&gpio3_base->oe) & ~(GPIO0), &gpio3_base->oe);
> +
> +	/* Now send a pulse on the GPIO pin */
> +	writel(GPIO0, &gpio3_base->setdataout);
> +	udelay(1);
> +	writel(GPIO0, &gpio3_base->cleardataout);
> +	udelay(1);
> +	writel(GPIO0, &gpio3_base->setdataout);

Use the omap gpio interface described in README.omap3

Tom