[U-Boot] [PATCH 0/3 v4] New MIIPHYBB implementation with multi-bus support

[U-Boot] [PATCH 0/3 v4] New MIIPHYBB implementation with multi-bus support

[Luigi 'Comio' Mantellini]

This patch rewrites the miiphybb ( Bit-banged MII bus driver ) in order to
support an arbitrary number of mii buses. This feature is useful when your
board uses different mii buses for different phys and all (or a part) of these
buses are implemented via bit-banging mode.

The driver requires that the following macros should be defined into the board
configuration file:

CONFIG_BITBANGMII       - Enable the miiphybb driver
CONFIG_BITBANGMII_MULTI - Enable the multi bus support

If the CONFIG_BITBANGMII_MULTI is not defined, the board's config file needs
to define at least the following macros:

MII_INIT      - Generic code to enable the MII bus (optional)
MDIO_DECLARE  - Declaration needed to access to the MDIO pin (optional)
MDIO_ACTIVE   - Activate the MDIO pin as out pin
MDIO_TRISTATE - Activate the MDIO pin as input/tristate pin
MDIO_READ     - Read the MDIO pin
MDIO(v)       - Write v on the MDIO pin
MDC_DECLARE   - Declaration needed to access to the MDC pin (optional)
MDC(v)        - Write v on the MDC pin

The previous macros make the driver compatible with the previous version
(that didn't support the multi-bus).

When the CONFIG_BITBANGMII_MULTI is also defined, the board code needs to fill
the bb_miiphy_buses[] array with a record for each required bus and declare
the bb_miiphy_buses_num variable with the number of mii buses.
The record (struct bb_miiphy_bus) has the following fields/callbacks (see
miiphy.h for details):

char name[]            - The symbolic name that must be equal to the MII bus
                         registered name
int (*init)()          - Initialization function called at startup time (just
                         before the Ethernet initialization)
int (*mdio_active)()   - Activate the MDIO pin as output
int (*mdio_tristate)() - Activate the MDIO pin as input/tristate pin
int (*set_mdio)()      - Write the MDIO pin
int (*get_mdio)()      - Read the MDIO pin
int (*set_mdc)()       - Write the MDC pin
int (*delay)()         - Delay function
void *priv             - Private data used by board specific code

The board code will look like:

struct bb_miiphy_bus bb_miiphy_buses[] = {
 { .name = "miibus#1", .init = b1_init, .mdio_active = b1_mdio_active, ... },
 { .name = "miibus#2", .init = b2_init, .mdio_active = b2_mdio_active, ... },
 ...
};
int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /
                          sizeof(bb_miiphy_buses[0]);

Patch Changelog:

v1 -- First (broken) release
v2 -- Fix some typos and disable callbacks pointers relacation (if
      CONFIG_RELOC_FIXUP_WORKS is not defined)
v3 -- Do not relocate NULL pointers
v4 -- Code Cleanup.

Luigi 'Comio' Mantellini (3):
  New Bit-banged MII driver (MIIPHYBB) implementation with multi-bus
    support.
  Add bb_miiphy_init call before any ethernet bring-up code.
  Update all board to support new bbmiiphy driver (with multibus
    support)

 drivers/net/phy/miiphybb.c   |  346 +++++++++++++++++++++++++++++-------------
 include/configs/ISPAN.h      |    4 +
 include/configs/MPC8260ADS.h |    3 +
 include/configs/MPC8266ADS.h |    4 +
 include/configs/MPC8560ADS.h |    4 +
 include/configs/Rattler.h    |    4 +
 include/configs/SBC8540.h    |    4 +
 include/configs/TQM8272.h    |    3 +
 include/configs/VoVPN-GW.h   |    4 +
 include/configs/ZPC1900.h    |    4 +
 include/configs/ep8248.h     |    4 +
 include/configs/ep82xxm.h    |    4 +
 include/configs/gw8260.h     |    4 +
 include/configs/hymod.h      |   12 ++
 include/configs/muas3001.h   |    4 +
 include/configs/ppmc8260.h   |    4 +
 include/configs/sacsng.h     |    4 +
 include/configs/sbc8260.h    |    4 +
 include/configs/sbc8560.h    |    4 +
 include/miiphy.h             |   25 +++-
 lib_arm/board.c              |    7 +
 lib_avr32/board.c            |    7 +
 lib_blackfin/board.c         |    7 +
 lib_i386/board.c             |    9 +-
 lib_m68k/board.c             |    7 +
 lib_mips/board.c             |    7 +
 lib_ppc/board.c              |    7 +
 lib_sh/board.c               |    7 +
 lib_sparc/board.c            |    7 +
 29 files changed, 408 insertions(+), 106 deletions(-)

[U-Boot] [PATCH 1/3 v4] New Bit-banged MII driver (MIIPHYBB) implementation with multi-bus support.

[Luigi 'Comio' Mantellini]

This patch rewrites the miiphybb ( Bit-banged MII bus driver ) in order to
support an arbitrary number of mii buses. This feature is useful when your
board uses different mii buses for different phys and all (or a part) of these
buses are implemented via bit-banging mode.

The driver requires that the following macros should be defined into the board
configuration file:

CONFIG_BITBANGMII       - Enable the miiphybb driver
CONFIG_BITBANGMII_MULTI - Enable the multi bus support

If the CONFIG_BITBANGMII_MULTI is not defined, the board's config file needs
to define at least the following macros:

MII_INIT      - Generic code to enable the MII bus (optional)
MDIO_DECLARE  - Declaration needed to access to the MDIO pin (optional)
MDIO_ACTIVE   - Activate the MDIO pin as out pin
MDIO_TRISTATE - Activate the MDIO pin as input/tristate pin
MDIO_READ     - Read the MDIO pin
MDIO(v)       - Write v on the MDIO pin
MDC_DECLARE   - Declaration needed to access to the MDC pin (optional)
MDC(v)        - Write v on the MDC pin

The previous macros make the driver compatible with the previous version
(that didn't support the multi-bus).

When the CONFIG_BITBANGMII_MULTI is also defined, the board code needs to fill
the bb_miiphy_buses[] array with a record for each required bus and declare
the bb_miiphy_buses_num variable with the number of mii buses.
The record (struct bb_miiphy_bus) has the following fields/callbacks (see
miiphy.h for details):

char name[]            - The symbolic name that must be equal to the MII bus
                         registered name
int (*init)()          - Initialization function called at startup time (just
                         before the Ethernet initialization)
int (*mdio_active)()   - Activate the MDIO pin as output
int (*mdio_tristate)() - Activate the MDIO pin as input/tristate pin
int (*set_mdio)()      - Write the MDIO pin
int (*get_mdio)()      - Read the MDIO pin
int (*set_mdc)()       - Write the MDC pin
int (*delay)()         - Delay function
void *priv             - Private data used by board specific code

The board code will look like:

struct bb_miiphy_bus bb_miiphy_buses[] = {
 { .name = "miibus#1", .init = b1_init, .mdio_active = b1_mdio_active, ... },
 { .name = "miibus#2", .init = b2_init, .mdio_active = b2_mdio_active, ... },
 ...
};
int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /
                          sizeof(bb_miiphy_buses[0]);

Signed-off-by: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
---
 drivers/net/phy/miiphybb.c |  346 +++++++++++++++++++++++++++++++-------------
 include/miiphy.h           |   25 +++-
 2 files changed, 266 insertions(+), 105 deletions(-)

diff --git a/drivers/net/phy/miiphybb.c b/drivers/net/phy/miiphybb.c
index b77c917..259b3ff 100644
--- a/drivers/net/phy/miiphybb.c
+++ b/drivers/net/phy/miiphybb.c
@@ -1,4 +1,7 @@
 /*
+ * (C) Copyright 2009 Industrie Dial Face S.p.A.
+ * Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
+ *
  * (C) Copyright 2001
  * Gerald Van Baren, Custom IDEAS, vanbaren at cideas.com.
  *
@@ -29,18 +32,144 @@
 #include <common.h>
 #include <ioports.h>
 #include <ppc_asm.tmpl>
+#include <miiphy.h>
+
+#define BB_MII_RELOCATE(v,off) (v += (v?off:0))
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifndef CONFIG_BITBANGMII_MULTI
+
+/*
+ * If CONFIG_BITBANGMII_MULTI is not defined we use a
+ * compatibility layer with the previous miiphybb implementation
+ * based on macros usage.
+ *
+ */
+static int bb_mii_init_wrap(struct bb_miiphy_bus *bus)
+{
+#ifdef MII_INIT
+	MII_INIT;
+#endif
+	return 0;
+}
+
+static int bb_mdio_active_wrap(struct bb_miiphy_bus *bus)
+{
+#ifdef MDIO_DECLARE
+	MDIO_DECLARE;
+#endif
+	MDIO_ACTIVE;
+	return 0;
+}
+
+static int bb_mdio_tristate_wrap(struct bb_miiphy_bus *bus)
+{
+#ifdef MDIO_DECLARE
+	MDIO_DECLARE;
+#endif
+	MDIO_TRISTATE;
+	return 0;
+}
+
+static int bb_set_mdio_wrap(struct bb_miiphy_bus *bus, int v)
+{
+#ifdef MDIO_DECLARE
+	MDIO_DECLARE;
+#endif
+	MDIO(v);
+	return 0;
+}
+
+static int bb_get_mdio_wrap(struct bb_miiphy_bus *bus, int *v)
+{
+#ifdef MDIO_DECLARE
+	MDIO_DECLARE;
+#endif
+	*v = MDIO_READ;
+	return 0;
+}
+
+static int bb_set_mdc_wrap(struct bb_miiphy_bus *bus, int v)
+{
+#ifdef MDC_DECLARE
+	MDC_DECLARE;
+#endif
+	MDC(v);
+	return 0;
+}
+
+static int bb_delay_wrap(struct bb_miiphy_bus *bus)
+{
+	MIIDELAY;
+	return 0;
+}
+
+struct bb_miiphy_bus bb_miiphy_buses[] = {
+	{
+		.name = BB_MII_DEVNAME,
+		.init = bb_mii_init_wrap,
+		.mdio_active = bb_mdio_active_wrap,
+		.mdio_tristate = bb_mdio_tristate_wrap,
+		.set_mdio = bb_set_mdio_wrap,
+		.get_mdio = bb_get_mdio_wrap,
+		.set_mdc = bb_set_mdc_wrap,
+		.delay = bb_delay_wrap,
+	}
+};
+
+extern int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /
+                                 sizeof(bb_miiphy_buses[0]);
+#endif
+
+void bb_miiphy_init(void)
+{
+	int i;
+
+	for (i = 0; i < bb_miiphy_buses_num; i++) {
+#if !defined(CONFIG_RELOC_FIXUP_WORKS)
+		/* Relocate the hook pointers*/
+		BB_MII_RELOCATE(bb_miiphy_buses[i].init, gd->reloc_off);
+		BB_MII_RELOCATE(bb_miiphy_buses[i].mdio_active, gd->reloc_off);
+		BB_MII_RELOCATE(bb_miiphy_buses[i].mdio_tristate, gd->reloc_off);
+		BB_MII_RELOCATE(bb_miiphy_buses[i].set_mdio, gd->reloc_off);
+		BB_MII_RELOCATE(bb_miiphy_buses[i].get_mdio, gd->reloc_off);
+		BB_MII_RELOCATE(bb_miiphy_buses[i].set_mdc, gd->reloc_off);
+		BB_MII_RELOCATE(bb_miiphy_buses[i].delay, gd->reloc_off);
+#endif
+		if (bb_miiphy_buses[i].init != NULL) {
+			bb_miiphy_buses[i].init(&bb_miiphy_buses[i]);
+		}
+	}
+}
+
+static inline struct bb_miiphy_bus *bb_miiphy_getbus(char *devname)
+{
+#ifdef CONFIG_BITBANGMII_MULTI
+	int i;
+
+	/* Search the correct bus */
+	for (i = 0; i < bb_miiphy_buses_num; i++) {
+		if (!strcmp(bb_miiphy_buses[i].name, devname)) {
+			return &bb_miiphy_buses[i];
+		}
+	}
+	return NULL;
+#else
+	/* We have just one bitbanging bus */
+	return &bb_miiphy_buses[0];
+#endif
+}
 
 /*****************************************************************************
  *
  * Utility to send the preamble, address, and register (common to read
  * and write).
  */
-static void miiphy_pre (char read, unsigned char addr, unsigned char reg)
+static void miiphy_pre(struct bb_miiphy_bus *bus, char read,
+                       unsigned char addr, unsigned char reg)
 {
-	int j;			/* counter */
-#if !(defined(CONFIG_EP8248) || defined(CONFIG_EP82XXM))
-	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT);
-#endif
+	int j;
 
 	/*
 	 * Send a 32 bit preamble ('1's) with an extra '1' bit for good measure.
@@ -50,67 +179,66 @@ static void miiphy_pre (char read, unsigned char addr, unsigned char reg)
 	 * but it is safer and will be much more robust.
 	 */
 
-	MDIO_ACTIVE;
-	MDIO (1);
+	bus->mdio_active(bus);
+	bus->set_mdio(bus, 1);
 	for (j = 0; j < 32; j++) {
-		MDC (0);
-		MIIDELAY;
-		MDC (1);
-		MIIDELAY;
+		bus->set_mdc(bus, 0);
+		bus->delay(bus);
+		bus->set_mdc(bus, 1);
+		bus->delay(bus);
 	}
 
 	/* send the start bit (01) and the read opcode (10) or write (10) */
-	MDC (0);
-	MDIO (0);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
-	MDC (0);
-	MDIO (1);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
-	MDC (0);
-	MDIO (read);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
-	MDC (0);
-	MDIO (!read);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
+	bus->set_mdc(bus, 0);
+	bus->set_mdio(bus, 0);
+	bus->delay(bus);
+	bus->set_mdc(bus, 1);
+	bus->delay(bus);
+	bus->set_mdc(bus, 0);
+	bus->set_mdio(bus, 1);
+	bus->delay(bus);
+	bus->set_mdc(bus, 1);
+	bus->delay(bus);
+	bus->set_mdc(bus, 0);
+	bus->set_mdio(bus, read);
+	bus->delay(bus);
+	bus->set_mdc(bus, 1);
+	bus->delay(bus);
+	bus->set_mdc(bus, 0);
+	bus->set_mdio(bus, !read);
+	bus->delay(bus);
+	bus->set_mdc(bus, 1);
+	bus->delay(bus);
 
 	/* send the PHY address */
 	for (j = 0; j < 5; j++) {
-		MDC (0);
+		bus->set_mdc(bus, 0);
 		if ((addr & 0x10) == 0) {
-			MDIO (0);
+			bus->set_mdio(bus, 0);
 		} else {
-			MDIO (1);
+			bus->set_mdio(bus, 1);
 		}
-		MIIDELAY;
-		MDC (1);
-		MIIDELAY;
+		bus->delay(bus);
+		bus->set_mdc(bus, 1);
+		bus->delay(bus);
 		addr <<= 1;
 	}
 
 	/* send the register address */
 	for (j = 0; j < 5; j++) {
-		MDC (0);
+		bus->set_mdc(bus, 0);
 		if ((reg & 0x10) == 0) {
-			MDIO (0);
+			bus->set_mdio(bus, 0);
 		} else {
-			MDIO (1);
+			bus->set_mdio(bus, 1);
 		}
-		MIIDELAY;
-		MDC (1);
-		MIIDELAY;
+		bus->delay(bus);
+		bus->set_mdc(bus, 1);
+		bus->delay(bus);
 		reg <<= 1;
 	}
 }
 
-
 /*****************************************************************************
  *
  * Read a MII PHY register.
@@ -118,63 +246,69 @@ static void miiphy_pre (char read, unsigned char addr, unsigned char reg)
  * Returns:
  *   0 on success
  */
-int bb_miiphy_read (char *devname, unsigned char addr,
-		unsigned char reg, unsigned short *value)
+int bb_miiphy_read(char *devname, unsigned char addr,
+                   unsigned char reg, unsigned short *value)
 {
-	short rdreg;		/* register working value */
-	int j;			/* counter */
-#if !(defined(CONFIG_EP8248) || defined(CONFIG_EP82XXM))
-	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT);
-#endif
+	short rdreg; /* register working value */
+	int v;
+	int j; /* counter */
+	struct bb_miiphy_bus *bus;
+
+	bus = bb_miiphy_getbus(devname);
+	if (bus == NULL) {
+		return -1;
+	}
 
 	if (value == NULL) {
 		puts("NULL value pointer\n");
-		return (-1);
+		return -1;
 	}
 
-	miiphy_pre (1, addr, reg);
+	miiphy_pre (bus, 1, addr, reg);
 
 	/* tri-state our MDIO I/O pin so we can read */
-	MDC (0);
-	MDIO_TRISTATE;
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
+	bus->set_mdc(bus, 0);
+	bus->mdio_tristate(bus);
+	bus->delay(bus);
+	bus->set_mdc(bus, 1);
+	bus->delay(bus);
 
 	/* check the turnaround bit: the PHY should be driving it to zero */
-	if (MDIO_READ != 0) {
+	bus->get_mdio(bus, &v);
+	if (v != 0) {
 		/* puts ("PHY didn't drive TA low\n"); */
 		for (j = 0; j < 32; j++) {
-			MDC (0);
-			MIIDELAY;
-			MDC (1);
-			MIIDELAY;
+			bus->set_mdc(bus, 0);
+			bus->delay(bus);
+			bus->set_mdc(bus, 1);
+			bus->delay(bus);
 		}
 		/* There is no PHY, set value to 0xFFFF and return */
 		*value = 0xFFFF;
-		return (-1);
+		return -1;
 	}
 
-	MDC (0);
-	MIIDELAY;
+	bus->set_mdc(bus, 0);
+	bus->delay(bus);
 
 	/* read 16 bits of register data, MSB first */
 	rdreg = 0;
 	for (j = 0; j < 16; j++) {
-		MDC (1);
-		MIIDELAY;
+		bus->set_mdc(bus, 1);
+		bus->delay(bus);
 		rdreg <<= 1;
-		rdreg |= MDIO_READ;
-		MDC (0);
-		MIIDELAY;
+		bus->get_mdio(bus, &v);
+		rdreg |= (v & 0x1);
+		bus->set_mdc(bus, 0);
+		bus->delay(bus);
 	}
 
-	MDC (1);
-	MIIDELAY;
-	MDC (0);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
+	bus->set_mdc(bus, 1);
+	bus->delay(bus);
+	bus->set_mdc(bus, 0);
+	bus->delay(bus);
+	bus->set_mdc(bus, 1);
+	bus->delay(bus);
 
 	*value = rdreg;
 
@@ -194,49 +328,53 @@ int bb_miiphy_read (char *devname, unsigned char addr,
  *   0 on success
  */
 int bb_miiphy_write (char *devname, unsigned char addr,
-		unsigned char reg, unsigned short value)
+                     unsigned char reg, unsigned short value)
 {
+	struct bb_miiphy_bus *bus;
 	int j;			/* counter */
-#if !(defined(CONFIG_EP8248) || defined(CONFIG_EP82XXM))
-	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT);
-#endif
 
-	miiphy_pre (0, addr, reg);
+	bus = bb_miiphy_getbus(devname);
+	if (bus == NULL) {
+		/* Bus not found! */
+		return -1;
+	}
+
+	miiphy_pre (bus, 0, addr, reg);
 
 	/* send the turnaround (10) */
-	MDC (0);
-	MDIO (1);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
-	MDC (0);
-	MDIO (0);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
+	bus->set_mdc(bus, 0);
+	bus->set_mdio(bus, 1);
+	bus->delay(bus);
+	bus->set_mdc(bus, 1);
+	bus->delay(bus);
+	bus->set_mdc(bus, 0);
+	bus->set_mdio(bus, 0);
+	bus->delay(bus);
+	bus->set_mdc(bus, 1);
+	bus->delay(bus);
 
 	/* write 16 bits of register data, MSB first */
 	for (j = 0; j < 16; j++) {
-		MDC (0);
+		bus->set_mdc(bus, 0);
 		if ((value & 0x00008000) == 0) {
-			MDIO (0);
+			bus->set_mdio(bus, 0);
 		} else {
-			MDIO (1);
+			bus->set_mdio(bus, 1);
 		}
-		MIIDELAY;
-		MDC (1);
-		MIIDELAY;
+		bus->delay(bus);
+		bus->set_mdc(bus, 1);
+		bus->delay(bus);
 		value <<= 1;
 	}
 
 	/*
 	 * Tri-state the MDIO line.
 	 */
-	MDIO_TRISTATE;
-	MDC (0);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
+	bus->mdio_tristate(bus);
+	bus->set_mdc(bus, 0);
+	bus->delay(bus);
+	bus->set_mdc(bus, 1);
+	bus->delay(bus);
 
 	return 0;
-}
+}
\ No newline at end of file
diff --git a/include/miiphy.h b/include/miiphy.h
index fa33ec7..5362125 100644
--- a/include/miiphy.h
+++ b/include/miiphy.h
@@ -19,6 +19,8 @@
 |
 |	COPYRIGHT   I B M   CORPORATION 1999
 |	LICENSED MATERIAL  -  PROGRAM PROPERTY OF I B M
+|
+|   Additions (C) Copyright 2009 Industrie Dial Face S.p.A.
 +----------------------------------------------------------------------------*/
 /*----------------------------------------------------------------------------+
 |
@@ -61,12 +63,33 @@ char *miiphy_get_current_dev (void);
 
 void miiphy_listdev (void);
 
-#define BB_MII_DEVNAME	"bbmii"
+#ifdef CONFIG_BITBANGMII
+
+#define BB_MII_DEVNAME	"bb_miiphy"
+
+struct bb_miiphy_bus {
+	char name[NAMESIZE];
+	int (*init)(struct bb_miiphy_bus *bus);
+	int (*mdio_active)(struct bb_miiphy_bus *bus);
+	int (*mdio_tristate)(struct bb_miiphy_bus *bus);
+	int (*set_mdio)(struct bb_miiphy_bus *bus, int v);
+	int (*get_mdio)(struct bb_miiphy_bus *bus, int *v);
+	int (*set_mdc)(struct bb_miiphy_bus *bus, int v);
+	int (*delay)(struct bb_miiphy_bus *bus);
+#ifdef CONFIG_BITBANGMII_MULTI
+	void *priv;
+#endif
+};
+
+extern struct bb_miiphy_bus bb_miiphy_buses[];
+extern int bb_miiphy_buses_num;
 
+void bb_miiphy_init (void);
 int bb_miiphy_read (char *devname, unsigned char addr,
 		    unsigned char reg, unsigned short *value);
 int bb_miiphy_write (char *devname, unsigned char addr,
 		     unsigned char reg, unsigned short value);
+#endif
 
 /* phy seed setup */
 #define AUTO			99
-- 
1.6.3.3

[U-Boot] [PATCH 2/3] Add bb_miiphy_init call before any ethernet bring-up code.

[Luigi 'Comio' Mantellini]

Signed-off-by: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
---
 lib_arm/board.c      |    7 +++++++
 lib_avr32/board.c    |    7 +++++++
 lib_blackfin/board.c |    7 +++++++
 lib_i386/board.c     |    9 ++++++++-
 lib_m68k/board.c     |    7 +++++++
 lib_mips/board.c     |    7 +++++++
 lib_ppc/board.c      |    7 +++++++
 lib_sh/board.c       |    7 +++++++
 lib_sparc/board.c    |    7 +++++++
 9 files changed, 64 insertions(+), 1 deletions(-)

diff --git a/lib_arm/board.c b/lib_arm/board.c
index a0e56d5..057cc21 100644
--- a/lib_arm/board.c
+++ b/lib_arm/board.c
@@ -50,6 +50,10 @@
 #include <onenand_uboot.h>
 #include <mmc.h>
 
+#ifdef CONFIG_BITBANGMII
+#include <miihpy.h>
+#endif
+
 #ifdef CONFIG_DRIVER_SMC91111
 #include "../drivers/net/smc91111.h"
 #endif
@@ -417,6 +421,9 @@ extern void davinci_eth_set_mac_addr (const u_int8_t *addr);
 	mmc_initialize (gd->bd);
 #endif
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 #if defined(CONFIG_NET_MULTI)
 	puts ("Net:   ");
diff --git a/lib_avr32/board.c b/lib_avr32/board.c
index 29999d8..1f5e681 100644
--- a/lib_avr32/board.c
+++ b/lib_avr32/board.c
@@ -27,6 +27,10 @@
 #include <version.h>
 #include <net.h>
 
+#ifdef CONFIG_BITBANGMII
+#include <miihpy.h>
+#endif
+
 #include <asm/initcalls.h>
 #include <asm/sections.h>
 
@@ -337,6 +341,9 @@ void board_init_r(gd_t *new_gd, ulong dest_addr)
 	if (s)
 		load_addr = simple_strtoul(s, NULL, 16);
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 	s = getenv("bootfile");
 	if (s)
diff --git a/lib_blackfin/board.c b/lib_blackfin/board.c
index 1053f69..6ce17d4 100644
--- a/lib_blackfin/board.c
+++ b/lib_blackfin/board.c
@@ -26,6 +26,10 @@
 #include <nand.h>	/* cannot even include nand.h if it isnt configured */
 #endif
 
+#ifdef CONFIG_BITBANGMII
+#include <miihpy.h>
+#endif
+
 #if defined(CONFIG_POST)
 #include <post.h>
 int post_flag;
@@ -270,6 +274,9 @@ void board_init_f(ulong bootflag)
 
 static void board_net_init_r(bd_t *bd)
 {
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #ifdef CONFIG_CMD_NET
 	uchar enetaddr[6];
 	char *s;
diff --git a/lib_i386/board.c b/lib_i386/board.c
index 0262b5e..452a5fc 100644
--- a/lib_i386/board.c
+++ b/lib_i386/board.c
@@ -1,6 +1,6 @@
 /*
  * (C) Copyright 2002
- * Daniel Engstr?m, Omicron Ceti AB, daniel at omicron.se
+ * Daniel Engstr???m, Omicron Ceti AB, daniel at omicron.se
  *
  * (C) Copyright 2002
  * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
@@ -39,6 +39,10 @@
 #include <ide.h>
 #include <asm/u-boot-i386.h>
 
+#ifdef CONFIG_BITBANGMII
+#include <miihpy.h>
+#endif
+
 DECLARE_GLOBAL_DATA_PTR;
 
 extern long _i386boot_start;
@@ -351,6 +355,9 @@ void start_i386boot (void)
 	doc_init();
 #endif
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 #if defined(CONFIG_NET_MULTI)
 	WATCHDOG_RESET();
diff --git a/lib_m68k/board.c b/lib_m68k/board.c
index 3d88530..768a55c 100644
--- a/lib_m68k/board.c
+++ b/lib_m68k/board.c
@@ -63,6 +63,10 @@
 #include <spi.h>
 #endif
 
+#ifdef CONFIG_BITBANGMII
+#include <miihpy.h>
+#endif
+
 #include <nand.h>
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -630,6 +634,9 @@ void board_init_r (gd_t *id, ulong dest_addr)
 	nand_init();		/* go init the NAND */
 #endif
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 	WATCHDOG_RESET();
 #if defined(FEC_ENET)
diff --git a/lib_mips/board.c b/lib_mips/board.c
index f62a46a..81d6681 100644
--- a/lib_mips/board.c
+++ b/lib_mips/board.c
@@ -33,6 +33,10 @@
 #include <onenand_uboot.h>
 #include <spi.h>
 
+#ifdef CONFIG_BITBANGMII
+#include <miihpy.h>
+#endif
+
 DECLARE_GLOBAL_DATA_PTR;
 
 #if ( ((CONFIG_ENV_ADDR+CONFIG_ENV_SIZE) < CONFIG_SYS_MONITOR_BASE) || \
@@ -407,6 +411,9 @@ void board_init_r (gd_t *id, ulong dest_addr)
 	misc_init_r ();
 #endif
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 #if defined(CONFIG_NET_MULTI)
 	puts ("Net:   ");
diff --git a/lib_ppc/board.c b/lib_ppc/board.c
index f9dbdb9..b19e6be 100644
--- a/lib_ppc/board.c
+++ b/lib_ppc/board.c
@@ -83,6 +83,10 @@
 #include <asm/mp.h>
 #endif
 
+#ifdef CONFIG_BITBANGMII
+#include <miihpy.h>
+#endif
+
 #ifdef CONFIG_SYS_UPDATE_FLASH_SIZE
 extern int update_flash_size (int flash_size);
 #endif
@@ -992,6 +996,9 @@ void board_init_r (gd_t *id, ulong dest_addr)
 	doc_init ();
 #endif
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 #if defined(CONFIG_NET_MULTI)
 	WATCHDOG_RESET ();
diff --git a/lib_sh/board.c b/lib_sh/board.c
index 5d61f0d..b769788 100644
--- a/lib_sh/board.c
+++ b/lib_sh/board.c
@@ -28,6 +28,10 @@
 #include <net.h>
 #include <environment.h>
 
+#ifdef CONFIG_BITBANGMII
+#include <miihpy.h>
+#endif
+
 extern void malloc_bin_reloc (void);
 extern int cpu_init(void);
 extern int board_init(void);
@@ -178,6 +182,9 @@ void sh_generic_init(void)
 #endif /* CONFIG_WATCHDOG*/
 
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 	{
 		char *s;
diff --git a/lib_sparc/board.c b/lib_sparc/board.c
index 6aadb56..f00f24d 100644
--- a/lib_sparc/board.c
+++ b/lib_sparc/board.c
@@ -49,6 +49,10 @@
 #include <ambapp.h>
 #endif
 
+#ifdef CONFIG_BITBANGMII
+#include <miihpy.h>
+#endif
+
 DECLARE_GLOBAL_DATA_PTR;
 
 /* Debug options
@@ -405,6 +409,9 @@ void board_init_f(ulong bootflag)
 	doc_init();
 #endif
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 #if defined(CONFIG_NET_MULTI)
 	WATCHDOG_RESET();
-- 
1.6.3.3

[U-Boot] [PATCH 3/3] Update all board to support new bbmiiphy driver (with multibus support)

[Luigi 'Comio' Mantellini]

Signed-off-by: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
---
 include/configs/ISPAN.h      |    4 ++++
 include/configs/MPC8260ADS.h |    3 +++
 include/configs/MPC8266ADS.h |    4 ++++
 include/configs/MPC8560ADS.h |    4 ++++
 include/configs/Rattler.h    |    4 ++++
 include/configs/SBC8540.h    |    4 ++++
 include/configs/TQM8272.h    |    3 +++
 include/configs/VoVPN-GW.h   |    4 ++++
 include/configs/ZPC1900.h    |    4 ++++
 include/configs/ep8248.h     |    4 ++++
 include/configs/ep82xxm.h    |    4 ++++
 include/configs/gw8260.h     |    4 ++++
 include/configs/hymod.h      |   12 ++++++++++++
 include/configs/muas3001.h   |    4 ++++
 include/configs/ppmc8260.h   |    4 ++++
 include/configs/sacsng.h     |    4 ++++
 include/configs/sbc8260.h    |    4 ++++
 include/configs/sbc8560.h    |    4 ++++
 18 files changed, 78 insertions(+), 0 deletions(-)

diff --git a/include/configs/ISPAN.h b/include/configs/ISPAN.h
index 6eb466a..02a188d 100644
--- a/include/configs/ISPAN.h
+++ b/include/configs/ISPAN.h
@@ -84,6 +84,10 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT		3		/* Port D */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 
 #define CONFIG_SYS_MDIO_PIN		0x00040000	/* PD13 */
 #define CONFIG_SYS_MDC_PIN		0x00080000	/* PD12 */
diff --git a/include/configs/MPC8260ADS.h b/include/configs/MPC8260ADS.h
index 39b8b8f..078cb6a 100644
--- a/include/configs/MPC8260ADS.h
+++ b/include/configs/MPC8260ADS.h
@@ -150,6 +150,9 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT	2		/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
 
 #if CONFIG_ADSTYPE == CONFIG_SYS_8272ADS
 #define CONFIG_SYS_MDIO_PIN	0x00002000	/* PC18 */
diff --git a/include/configs/MPC8266ADS.h b/include/configs/MPC8266ADS.h
index b0162c3..fdfefc0 100644
--- a/include/configs/MPC8266ADS.h
+++ b/include/configs/MPC8266ADS.h
@@ -96,6 +96,10 @@
  * Port pins used for bit-banged MII communictions (if applicable).
  */
 #define MDIO_PORT	2	/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
 #define MDIO_READ	((iop->pdat &  0x00400000) != 0)
diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index 8ddce5c..54320e5 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -363,6 +363,10 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT	2		/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
 #define MDIO_READ	((iop->pdat &  0x00400000) != 0)
diff --git a/include/configs/Rattler.h b/include/configs/Rattler.h
index 5b6f271..b2427b2 100644
--- a/include/configs/Rattler.h
+++ b/include/configs/Rattler.h
@@ -103,6 +103,10 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT		2	/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE		(iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE		(iop->pdir &= ~0x00400000)
 #define MDIO_READ		((iop->pdat &  0x00400000) != 0)
diff --git a/include/configs/SBC8540.h b/include/configs/SBC8540.h
index 7cde39b..58b0a68 100644
--- a/include/configs/SBC8540.h
+++ b/include/configs/SBC8540.h
@@ -290,6 +290,10 @@
    * GPIO pins used for bit-banged MII communications
    */
   #define MDIO_PORT	2		/* Port C */
+  #define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+  #define MDC_DECLARE	MDIO_DECLARE
+
   #define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
   #define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
   #define MDIO_READ	((iop->pdat &  0x00400000) != 0)
diff --git a/include/configs/TQM8272.h b/include/configs/TQM8272.h
index 6c462af..22df917 100644
--- a/include/configs/TQM8272.h
+++ b/include/configs/TQM8272.h
@@ -219,6 +219,9 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT	2		/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
 
 #if STK82xx_150
 #define CONFIG_SYS_MDIO_PIN	0x00008000	/* PC16 */
diff --git a/include/configs/VoVPN-GW.h b/include/configs/VoVPN-GW.h
index b2d75e3..8eabfea 100644
--- a/include/configs/VoVPN-GW.h
+++ b/include/configs/VoVPN-GW.h
@@ -124,6 +124,10 @@
 #define CONFIG_BITBANGMII
 
 #define MDIO_PORT			1		/* Port B */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define CONFIG_SYS_MDIO_PIN			0x00002000	/* PB18 */
 #define CONFIG_SYS_MDC_PIN			0x00001000	/* PB19 */
 #define MDIO_ACTIVE			(iop->pdir |=  CONFIG_SYS_MDIO_PIN)
diff --git a/include/configs/ZPC1900.h b/include/configs/ZPC1900.h
index 9cda3f9..dd09e83 100644
--- a/include/configs/ZPC1900.h
+++ b/include/configs/ZPC1900.h
@@ -86,6 +86,10 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT		2	/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE		(iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE		(iop->pdir &= ~0x00400000)
 #define MDIO_READ		((iop->pdat &  0x00400000) != 0)
diff --git a/include/configs/ep8248.h b/include/configs/ep8248.h
index cb4185a..37f062f 100644
--- a/include/configs/ep8248.h
+++ b/include/configs/ep8248.h
@@ -92,6 +92,10 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT		0	/* Not used - implemented in BCSR */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE		(*(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFB)
 #define MDIO_TRISTATE		(*(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x04)
 #define MDIO_READ		(*(vu_char *)(CONFIG_SYS_BCSR + 8) & 1)
diff --git a/include/configs/ep82xxm.h b/include/configs/ep82xxm.h
index 239ff67..fc6905b 100644
--- a/include/configs/ep82xxm.h
+++ b/include/configs/ep82xxm.h
@@ -85,6 +85,10 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT		0	/* Not used - implemented in BCSR */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE		(*(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFB)
 #define MDIO_TRISTATE		(*(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x04)
 #define MDIO_READ		(*(vu_char *)(CONFIG_SYS_BCSR + 8) & 1)
diff --git a/include/configs/gw8260.h b/include/configs/gw8260.h
index 53a001d..6bf17b0 100644
--- a/include/configs/gw8260.h
+++ b/include/configs/gw8260.h
@@ -212,6 +212,10 @@
  * Port pins used for bit-banged MII communictions (if applicable).
  */
 #define MDIO_PORT   2       /* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE    (iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE  (iop->pdir &= ~0x00400000)
 #define MDIO_READ     ((iop->pdat &  0x00400000) != 0)
diff --git a/include/configs/hymod.h b/include/configs/hymod.h
index 284672b..328ccf2 100644
--- a/include/configs/hymod.h
+++ b/include/configs/hymod.h
@@ -93,6 +93,10 @@
 # define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB)
 
 # define MDIO_PORT		0		/* Port A */
+# define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+# define MDC_DECLARE	MDIO_DECLARE
+
 # define MDIO_DATA_PINMASK	0x00040000	/* Pin 13 */
 # define MDIO_CLCK_PINMASK	0x00080000	/* Pin 12 */
 
@@ -110,6 +114,10 @@
 # define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB)
 
 # define MDIO_PORT		0		/* Port A */
+# define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+# define MDC_DECLARE	MDIO_DECLARE
+
 # define MDIO_DATA_PINMASK	0x00000040	/* Pin 25 */
 # define MDIO_CLCK_PINMASK	0x00000080	/* Pin 24 */
 
@@ -127,6 +135,10 @@
 # define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB)
 
 # define MDIO_PORT		0		/* Port A */
+# define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+# define MDC_DECLARE	MDIO_DECLARE
+
 # define MDIO_DATA_PINMASK	0x00000100	/* Pin 23 */
 # define MDIO_CLCK_PINMASK	0x00000200	/* Pin 22 */
 
diff --git a/include/configs/muas3001.h b/include/configs/muas3001.h
index c94daa3..f830aaf 100644
--- a/include/configs/muas3001.h
+++ b/include/configs/muas3001.h
@@ -101,6 +101,10 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT	0		/* Port A */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 
 #define CONFIG_SYS_MDIO_PIN	0x00200000	/* PA10 */
 #define CONFIG_SYS_MDC_PIN	0x00400000	/* PA9  */
diff --git a/include/configs/ppmc8260.h b/include/configs/ppmc8260.h
index ff7d614..31a0c2f 100644
--- a/include/configs/ppmc8260.h
+++ b/include/configs/ppmc8260.h
@@ -182,6 +182,10 @@
  * Port pins used for bit-banged MII communictions (if applicable).
  */
 #define MDIO_PORT	2	/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
 #define MDIO_READ	((iop->pdat &  0x00400000) != 0)
diff --git a/include/configs/sacsng.h b/include/configs/sacsng.h
index 0ab6fc3..d84f8ed 100644
--- a/include/configs/sacsng.h
+++ b/include/configs/sacsng.h
@@ -179,6 +179,10 @@
  */
 
 #define MDIO_PORT	2	        /* Port A=0, B=1, C=2, D=3 */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE	(iop->pdir |=  0x40000000)
 #define MDIO_TRISTATE	(iop->pdir &= ~0x40000000)
 #define MDIO_READ	((iop->pdat &  0x40000000) != 0)
diff --git a/include/configs/sbc8260.h b/include/configs/sbc8260.h
index 26ed557..ec5b0f9 100644
--- a/include/configs/sbc8260.h
+++ b/include/configs/sbc8260.h
@@ -201,6 +201,10 @@
  * Port pins used for bit-banged MII communictions (if applicable).
  */
 #define MDIO_PORT	2	/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
 #define MDIO_READ	((iop->pdat &  0x00400000) != 0)
diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h
index a6b15f7..5a04950 100644
--- a/include/configs/sbc8560.h
+++ b/include/configs/sbc8560.h
@@ -293,6 +293,10 @@
    * GPIO pins used for bit-banged MII communications
    */
   #define MDIO_PORT	2		/* Port C */
+  #define MDIO_DECLARE	volatile ioport_t *iop = \
+						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+  #define MDC_DECLARE	MDIO_DECLARE
+
   #define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
   #define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
   #define MDIO_READ	((iop->pdat &  0x00400000) != 0)
-- 
1.6.3.3

[U-Boot] [PATCH 3/3] Update all board to support new bbmiiphy driver (with multibus support)

[Ben Warren]

Luigi,

Luigi 'Comio' Mantellini wrote:
> Signed-off-by: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
> ---
>  include/configs/ISPAN.h      |    4 ++++
>  include/configs/MPC8260ADS.h |    3 +++
>  include/configs/MPC8266ADS.h |    4 ++++
>  include/configs/MPC8560ADS.h |    4 ++++
>  include/configs/Rattler.h    |    4 ++++
>  include/configs/SBC8540.h    |    4 ++++
>  include/configs/TQM8272.h    |    3 +++
>  include/configs/VoVPN-GW.h   |    4 ++++
>  include/configs/ZPC1900.h    |    4 ++++
>  include/configs/ep8248.h     |    4 ++++
>  include/configs/ep82xxm.h    |    4 ++++
>  include/configs/gw8260.h     |    4 ++++
>  include/configs/hymod.h      |   12 ++++++++++++
>  include/configs/muas3001.h   |    4 ++++
>  include/configs/ppmc8260.h   |    4 ++++
>  include/configs/sacsng.h     |    4 ++++
>  include/configs/sbc8260.h    |    4 ++++
>  include/configs/sbc8560.h    |    4 ++++
>  18 files changed, 78 insertions(+), 0 deletions(-)
>
> diff --git a/include/configs/ISPAN.h b/include/configs/ISPAN.h
> index 6eb466a..02a188d 100644
> --- a/include/configs/ISPAN.h
> +++ b/include/configs/ISPAN.h
> @@ -84,6 +84,10 @@
>   * GPIO pins used for bit-banged MII communications
>   */
>  #define MDIO_PORT		3		/* Port D */
> +#define MDIO_DECLARE	volatile ioport_t *iop = \
> +						ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
>   
This, and all the others, are longer than 80 characters.  Please remove 
3 tabs from each and they'll fit
> +#define MDC_DECLARE		MDIO_DECLARE
>   
Please remove a tab so this aligns with MDIO_DECLARE.  Apply globally.

<snip>

regards,
Ben

[U-Boot] [PATCH 0/3 v4] New MIIPHYBB implementation with multi-bus support

[Ben Warren]

Hi Luigi,

Sorry, I'm going to have to ask you to re-submit again :(  There are a 
few things that need to be addressed
Luigi 'Comio' Mantellini wrote:
> This patch rewrites the miiphybb ( Bit-banged MII bus driver ) in order to
> support an arbitrary number of mii buses. This feature is useful when your
> board uses different mii buses for different phys and all (or a part) of these
> buses are implemented via bit-banging mode.
>
> The driver requires that the following macros should be defined into the board
> configuration file:
>
> CONFIG_BITBANGMII       - Enable the miiphybb driver
> CONFIG_BITBANGMII_MULTI - Enable the multi bus support
>
> If the CONFIG_BITBANGMII_MULTI is not defined, the board's config file needs
> to define at least the following macros:
>
> MII_INIT      - Generic code to enable the MII bus (optional)
> MDIO_DECLARE  - Declaration needed to access to the MDIO pin (optional)
> MDIO_ACTIVE   - Activate the MDIO pin as out pin
> MDIO_TRISTATE - Activate the MDIO pin as input/tristate pin
> MDIO_READ     - Read the MDIO pin
> MDIO(v)       - Write v on the MDIO pin
> MDC_DECLARE   - Declaration needed to access to the MDC pin (optional)
> MDC(v)        - Write v on the MDC pin
>
> The previous macros make the driver compatible with the previous version
> (that didn't support the multi-bus).
>
> When the CONFIG_BITBANGMII_MULTI is also defined, the board code needs to fill
> the bb_miiphy_buses[] array with a record for each required bus and declare
> the bb_miiphy_buses_num variable with the number of mii buses.
> The record (struct bb_miiphy_bus) has the following fields/callbacks (see
> miiphy.h for details):
>
> char name[]            - The symbolic name that must be equal to the MII bus
>                          registered name
> int (*init)()          - Initialization function called at startup time (just
>                          before the Ethernet initialization)
> int (*mdio_active)()   - Activate the MDIO pin as output
> int (*mdio_tristate)() - Activate the MDIO pin as input/tristate pin
> int (*set_mdio)()      - Write the MDIO pin
> int (*get_mdio)()      - Read the MDIO pin
> int (*set_mdc)()       - Write the MDC pin
> int (*delay)()         - Delay function
> void *priv             - Private data used by board specific code
>
> The board code will look like:
>
> struct bb_miiphy_bus bb_miiphy_buses[] = {
>  { .name = "miibus#1", .init = b1_init, .mdio_active = b1_mdio_active, ... },
>  { .name = "miibus#2", .init = b2_init, .mdio_active = b2_mdio_active, ... },
>  ...
> };
> int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /
>                           sizeof(bb_miiphy_buses[0]);
>
>   
Can you please copy this stuff into a README file (doc/README.bitbangMII 
maybe)?  I'm afraid all this wonderful changelog information will be in 
a place that people won't look.
If it wasn't for other problems with this patch set, I'd do it myself.
> Patch Changelog:
>
> v1 -- First (broken) release
> v2 -- Fix some typos and disable callbacks pointers relacation (if
>       CONFIG_RELOC_FIXUP_WORKS is not defined)
> v3 -- Do not relocate NULL pointers
> v4 -- Code Cleanup.
>
> Luigi 'Comio' Mantellini (3):
>   New Bit-banged MII driver (MIIPHYBB) implementation with multi-bus
>     support.
>   Add bb_miiphy_init call before any ethernet bring-up code.
>   Update all board to support new bbmiiphy driver (with multibus
>     support)
>
>  drivers/net/phy/miiphybb.c   |  346 +++++++++++++++++++++++++++++-------------
>  include/configs/ISPAN.h      |    4 +
>  include/configs/MPC8260ADS.h |    3 +
>  include/configs/MPC8266ADS.h |    4 +
>  include/configs/MPC8560ADS.h |    4 +
>  include/configs/Rattler.h    |    4 +
>  include/configs/SBC8540.h    |    4 +
>  include/configs/TQM8272.h    |    3 +
>  include/configs/VoVPN-GW.h   |    4 +
>  include/configs/ZPC1900.h    |    4 +
>  include/configs/ep8248.h     |    4 +
>  include/configs/ep82xxm.h    |    4 +
>  include/configs/gw8260.h     |    4 +
>  include/configs/hymod.h      |   12 ++
>  include/configs/muas3001.h   |    4 +
>  include/configs/ppmc8260.h   |    4 +
>  include/configs/sacsng.h     |    4 +
>  include/configs/sbc8260.h    |    4 +
>  include/configs/sbc8560.h    |    4 +
>  include/miiphy.h             |   25 +++-
>  lib_arm/board.c              |    7 +
>  lib_avr32/board.c            |    7 +
>  lib_blackfin/board.c         |    7 +
>  lib_i386/board.c             |    9 +-
>  lib_m68k/board.c             |    7 +
>  lib_mips/board.c             |    7 +
>  lib_ppc/board.c              |    7 +
>  lib_sh/board.c               |    7 +
>  lib_sparc/board.c            |    7 +
>  29 files changed, 408 insertions(+), 106 deletions(-)
>
> _______
Here are the real problems:

bwarren at bwarren-bldsrv$ CROSS_COMPILE=ppc_6xx- ./MAKEALL ppc
...
Configuring for ep8248 board...
board.c:87:20: error: miihpy.h: No such file or directory
board.c:87:20: error: miihpy.h: No such file or directory
board.c: In function 'board_init_r':
board.c:950: warning: implicit declaration of function 'bb_miiphy_init'
make[1]: *** [board.o] Error 1
make: *** [lib_ppc/libppc.a] Error 2

And all sorts of other PPC boards fail too.  Looks like a typo.

regards,
Ben

[U-Boot] [PATCH 0/3] New MIIPHYBB implementation with multi-bus support

[Luigi 'Comio' Mantellini]

From: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>


This patch rewrites the miiphybb ( Bit-banged MII bus driver ) in order to
support an arbitrary number of buses. This feature is useful when your board
uses different mii buses for different phys and all (or a part) of these buses
are implemented via bit-banging mode.

The driver requires that the following macros should be defined into the board
configuration file:

CONFIG_BITBANGMII       - Enable the miiphybb driver
CONFIG_BITBANGMII_MULTI - Enable the multi bus support

If the CONFIG_BITBANGMII_MULTI is not defined, the board's config file needs to define
the following macros:

MII_INIT      - Generic cod to enable the MII bus (like gpios setup)
MDIO_DECLARE  - Declaration needed to access to the MDIO pin
MDIO_ACTIVE   - Activate the MDIO pin as out pin
MDIO_TRISTATE - Activate the MDIO pin as input/tristate pin
MDIO_READ     - Read the MDIO pin
MDIO(v)       - Write v on the MDIO pin
MDC_DECLARE   - Declaration needed to access to the MDC pin
MDC(v)        - Write v on the MDC pin

The previous macros makes the driver at most compatible with the previous version
(that didn't support the multi-bus).

If the CONFIG_BITBANGMII_MULTI is defined, the board code needs to fill the
bbmiibusses[] array with a record for each required bus.
The record (struct bbmiibus) has the following fields/callbacks (see miiphy.h for
details):

char name[]            - The symbolic name that must be equal to the MII bus registered
                         name
int (*init)()          - Initialization function called at startup time (just before the
                         Ethernet initialization)
int (*mdio_active)()   - Activate the MDIO pin as output
int (*mdio_tristate)() - Activate the MDIO pin as input/tristate pin
int (*set_mdio)()      - Write the MDIO pin
int (*get_mdio)()      - Read the MDIO pin
int (*set_mdc)()       - Write the MDC pin
int (*delay)()         - Delay function
void *priv             - Private data used by board specific code

The board code will look like:

struct bbmiibus bbmiibusses[] = {
 { .name = "miibus#1", .init = b1_init, .mdio_active = b1_mdio_active, ... },
 { .name = "miibus#2", .init = b2_init, .mdio_active = b2_mdio_active, ... },
 ...
};

Luigi 'Comio' Mantellini (3):
  Bit-banged MII driver with multi-bus support.
  Add bb_miiphy_init call before any ethernet bring-up code.
  Update all board to support new bbmiiphy driver (with multibus
    support)

 drivers/net/phy/miiphybb.c   |  321 +++++++++++++++++++++++++++++-------------
 include/configs/ISPAN.h      |    3 +
 include/configs/MPC8260ADS.h |    2 +
 include/configs/MPC8266ADS.h |    3 +
 include/configs/MPC8560ADS.h |    3 +
 include/configs/Rattler.h    |    3 +
 include/configs/SBC8540.h    |    3 +
 include/configs/TQM8272.h    |    2 +
 include/configs/VoVPN-GW.h   |    3 +
 include/configs/ZPC1900.h    |    3 +
 include/configs/ep8248.h     |    3 +
 include/configs/ep82xxm.h    |    3 +
 include/configs/gw8260.h     |    3 +
 include/configs/hymod.h      |    9 ++
 include/configs/muas3001.h   |    3 +
 include/configs/ppmc8260.h   |    3 +
 include/configs/sacsng.h     |    3 +
 include/configs/sbc8260.h    |    3 +
 include/configs/sbc8560.h    |    3 +
 include/miiphy.h             |   22 +++
 lib_arm/board.c              |    3 +
 lib_avr32/board.c            |    3 +
 lib_blackfin/board.c         |    3 +
 lib_i386/board.c             |    3 +
 lib_m68k/board.c             |    3 +
 lib_mips/board.c             |    3 +
 lib_ppc/board.c              |    4 +-
 lib_sh/board.c               |    3 +
 lib_sparc/board.c            |    3 +
 29 files changed, 332 insertions(+), 97 deletions(-)

[U-Boot] [PATCH 1/3] Bit-banged MII driver with multi-bus support.

[Luigi 'Comio' Mantellini]

From: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>

Signed-off-by: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
---
 drivers/net/phy/miiphybb.c |  321 +++++++++++++++++++++++++++++++-------------
 include/miiphy.h           |   22 +++
 2 files changed, 247 insertions(+), 96 deletions(-)

diff --git a/drivers/net/phy/miiphybb.c b/drivers/net/phy/miiphybb.c
index b77c917..a60ca69 100644
--- a/drivers/net/phy/miiphybb.c
+++ b/drivers/net/phy/miiphybb.c
@@ -1,4 +1,7 @@
 /*
+ * (C) Copyright 2009 Industrie Dial Face S.p.A.
+ * Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
+ *
  * (C) Copyright 2001
  * Gerald Van Baren, Custom IDEAS, vanbaren at cideas.com.
  *
@@ -29,18 +32,134 @@
 #include <common.h>
 #include <ioports.h>
 #include <ppc_asm.tmpl>
+#include <miiphy.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifndef CONFIG_BITBANGMII_MULTI
+/*
+ * If CONFIG_BITBANGMII_MULTI is not defined we use a
+ * compatibility layer with the previous miiphybb implementation
+ * based on macros usage.
+ *
+ */
+static int bb_mii_init_wrap(bbmiibus *bus)
+{
+#ifdef MII_INIT
+	MII_INIT;
+#endif
+	return 0;
+}
+
+static int bb_mdio_active_wrap(struct bbmiibus *bus)
+{
+#ifdef MDIO_DECLARE
+	MDIO_DECLARE;
+#endif
+	MDIO_ACTIVE;
+	return 0;
+}
+
+static int bb_mdio_tristate_wrap(struct bbmiibus *bus)
+{
+#ifdef MDIO_DECLARE
+	MDIO_DECLARE;
+#endif
+	MDIO_TRISTATE;
+	return 0;
+}
+
+static int bb_set_mdio_wrap(struct bbmiibus *bus, int v)
+{
+#ifdef MDIO_DECLARE
+	MDIO_DECLARE;
+#endif
+	MDIO (v);
+	return 0;
+}
+
+static int bb_get_mdio_wrap(struct bbmiibus *bus, int *v)
+{
+#ifdef MDIO_DECLARE
+	MDIO_DECLARE;
+#endif
+	*v = MDIO_READ;
+	return 0;
+}
+
+static int bb_set_mdc_wrap(struct bbmiibus *bus, int v)
+{
+#ifdef MDC_DECLARE
+	MDC_DECLARE;
+#endif
+	MDC (v);
+	return 0;
+}
+
+static int bb_delay_wrap(struct bbmiibus *bus)
+{
+	MIIDELAY;
+	return 0;
+}
+
+struct bbmiibus bbmiibusses[] = {
+	{
+		.name = BB_MII_DEVNAME,
+		.init = bb_mii_init_wrap,
+		.mdio_active = bb_mdio_active_wrap,
+		.mdio_tristate = bb_mdio_tristate_wrap,
+		.set_mdio = bb_set_mdio_wrap,
+		.get_mdio = bb_get_mdio_wrap,
+		.set_mdc = bb_set_mdc_wrap,
+		.delay = bb_delay_wrap,
+	}
+};
+#endif
+
+void bb_miiphy_init(void)
+{
+	int i;
+	for (i = 0; i < sizeof(bbmiibusses)/sizeof(bbmiibusses[0]); i++) {
+		/* Reloate the hooks pointers*/
+		bbmiibusses[i].init += gd->reloc_off;
+		bbmiibusses[i].done += gd->reloc_off;
+		bbmiibusses[i].mdio_active += gd->reloc_off;
+		bbmiibusses[i].mdio_tristate += gd->reloc_off;
+		bbmiibusses[i].set_mdio += gd->reloc_off;
+		bbmiibusses[i].get_mdio += gd->reloc_off;
+		bbmiibusses[i].set_mdc += gd->reloc_off;
+		bbmiibusses[i].delay += gd->reloc_off;
+
+		if (bbmiibusses[i].init != NULL) {
+			bbmiibusses[i].init(&bbmiibusses[i]);
+		}
+	}
+}
+
+static inline struct bbmiibus *bb_miiphy_getbus(char *devname)
+{
+#ifdef CONFIG_BITBANGMII_MULTI
+	/* Search the correct bus */
+	for (j = 0; j < sizeof(bbmiibusses)/sizeof(bbmmis[0]); j++) {
+		if (!strcmp(bbmiibusses[i].name, devname)) {
+			return &bbmiibusses[i];
+		}
+	}
+	return NULL;
+#else
+	/* We have just one bitbanging bus */
+	return &bbmiibusses[0];
+#endif
+}
 
 /*****************************************************************************
  *
  * Utility to send the preamble, address, and register (common to read
  * and write).
  */
-static void miiphy_pre (char read, unsigned char addr, unsigned char reg)
+static void miiphy_pre (struct bbmiibus *bus, char read, unsigned char addr, unsigned char reg)
 {
 	int j;			/* counter */
-#if !(defined(CONFIG_EP8248) || defined(CONFIG_EP82XXM))
-	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT);
-#endif
 
 	/*
 	 * Send a 32 bit preamble ('1's) with an extra '1' bit for good measure.
@@ -50,67 +169,66 @@ static void miiphy_pre (char read, unsigned char addr, unsigned char reg)
 	 * but it is safer and will be much more robust.
 	 */
 
-	MDIO_ACTIVE;
-	MDIO (1);
+	bus->mdio_active(bus);
+	bus->set_mdio (bus, 1);
 	for (j = 0; j < 32; j++) {
-		MDC (0);
-		MIIDELAY;
-		MDC (1);
-		MIIDELAY;
+		bus->set_mdc (bus, 0);
+		bus->delay(bus);
+		bus->set_mdc (bus, 1);
+		bus->delay(bus);
 	}
 
 	/* send the start bit (01) and the read opcode (10) or write (10) */
-	MDC (0);
-	MDIO (0);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
-	MDC (0);
-	MDIO (1);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
-	MDC (0);
-	MDIO (read);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
-	MDC (0);
-	MDIO (!read);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
+	bus->set_mdc (bus, 0);
+	bus->set_mdio (bus, 0);
+	bus->delay(bus);
+	bus->set_mdc (bus, 1);
+	bus->delay(bus);
+	bus->set_mdc (bus, 0);
+	bus->set_mdio (bus, 1);
+	bus->delay(bus);
+	bus->set_mdc (bus, 1);
+	bus->delay(bus);
+	bus->set_mdc (bus, 0);
+	bus->set_mdio (bus, read);
+	bus->delay(bus);
+	bus->set_mdc (bus, 1);
+	bus->delay(bus);
+	bus->set_mdc (bus, 0);
+	bus->set_mdio (bus, !read);
+	bus->delay(bus);
+	bus->set_mdc (bus, 1);
+	bus->delay(bus);
 
 	/* send the PHY address */
 	for (j = 0; j < 5; j++) {
-		MDC (0);
+		bus->set_mdc (bus, 0);
 		if ((addr & 0x10) == 0) {
-			MDIO (0);
+			bus->set_mdio (bus, 0);
 		} else {
-			MDIO (1);
+			bus->set_mdio (bus, 1);
 		}
-		MIIDELAY;
-		MDC (1);
-		MIIDELAY;
+		bus->delay(bus);
+		bus->set_mdc (bus, 1);
+		bus->delay(bus);
 		addr <<= 1;
 	}
 
 	/* send the register address */
 	for (j = 0; j < 5; j++) {
-		MDC (0);
+		bus->set_mdc (bus, 0);
 		if ((reg & 0x10) == 0) {
-			MDIO (0);
+			bus->set_mdio (bus, 0);
 		} else {
-			MDIO (1);
+			bus->set_mdio (bus, 1);
 		}
-		MIIDELAY;
-		MDC (1);
-		MIIDELAY;
+		bus->delay(bus);
+		bus->set_mdc (bus, 1);
+		bus->delay(bus);
 		reg <<= 1;
 	}
 }
 
-
 /*****************************************************************************
  *
  * Read a MII PHY register.
@@ -122,59 +240,66 @@ int bb_miiphy_read (char *devname, unsigned char addr,
 		unsigned char reg, unsigned short *value)
 {
 	short rdreg;		/* register working value */
+	int v;
 	int j;			/* counter */
-#if !(defined(CONFIG_EP8248) || defined(CONFIG_EP82XXM))
-	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT);
-#endif
+	struct bbmiibus *bus;
+
+	bus = bb_miiphy_getbus(devname);
+	if (bus == NULL) {
+		/* Bus not found! */
+		return -1;
+	}
 
 	if (value == NULL) {
 		puts("NULL value pointer\n");
 		return (-1);
 	}
 
-	miiphy_pre (1, addr, reg);
+	miiphy_pre (bus, 1, addr, reg);
 
 	/* tri-state our MDIO I/O pin so we can read */
-	MDC (0);
-	MDIO_TRISTATE;
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
+	bus->set_mdc (bus, 0);
+	bus->mdio_tristate(bus);
+	bus->delay(bus);
+	bus->set_mdc (bus, 1);
+	bus->delay(bus);
 
 	/* check the turnaround bit: the PHY should be driving it to zero */
-	if (MDIO_READ != 0) {
+	bus->get_mdio(bus, &v);
+	if (v != 0) {
 		/* puts ("PHY didn't drive TA low\n"); */
 		for (j = 0; j < 32; j++) {
-			MDC (0);
-			MIIDELAY;
-			MDC (1);
-			MIIDELAY;
+			bus->set_mdc (bus, 0);
+			bus->delay(bus);
+			bus->set_mdc (bus, 1);
+			bus->delay(bus);
 		}
 		/* There is no PHY, set value to 0xFFFF and return */
 		*value = 0xFFFF;
 		return (-1);
 	}
 
-	MDC (0);
-	MIIDELAY;
+	bus->set_mdc (bus, 0);
+	bus->delay(bus);
 
 	/* read 16 bits of register data, MSB first */
 	rdreg = 0;
 	for (j = 0; j < 16; j++) {
-		MDC (1);
-		MIIDELAY;
+		bus->set_mdc (bus, 1);
+		bus->delay(bus);
 		rdreg <<= 1;
-		rdreg |= MDIO_READ;
-		MDC (0);
-		MIIDELAY;
+		bus->get_mdio(bus, &v);
+		rdreg |= (v & 0x1);
+		bus->set_mdc (bus, 0);
+		bus->delay(bus);
 	}
 
-	MDC (1);
-	MIIDELAY;
-	MDC (0);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
+	bus->set_mdc (bus, 1);
+	bus->delay(bus);
+	bus->set_mdc (bus, 0);
+	bus->delay(bus);
+	bus->set_mdc (bus, 1);
+	bus->delay(bus);
 
 	*value = rdreg;
 
@@ -196,47 +321,51 @@ int bb_miiphy_read (char *devname, unsigned char addr,
 int bb_miiphy_write (char *devname, unsigned char addr,
 		unsigned char reg, unsigned short value)
 {
+	struct bbmiibus *bus;
 	int j;			/* counter */
-#if !(defined(CONFIG_EP8248) || defined(CONFIG_EP82XXM))
-	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT);
-#endif
 
-	miiphy_pre (0, addr, reg);
+	bus = bb_miiphy_getbus(devname);
+	if (bus == NULL) {
+		/* Bus not found! */
+		return -1;
+	}
+
+	miiphy_pre (bus, 0, addr, reg);
 
 	/* send the turnaround (10) */
-	MDC (0);
-	MDIO (1);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
-	MDC (0);
-	MDIO (0);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
+	bus->set_mdc (bus, 0);
+	bus->set_mdio (bus, 1);
+	bus->delay(bus);
+	bus->set_mdc (bus, 1);
+	bus->delay(bus);
+	bus->set_mdc (bus, 0);
+	bus->set_mdio (bus, 0);
+	bus->delay(bus);
+	bus->set_mdc (bus, 1);
+	bus->delay(bus);
 
 	/* write 16 bits of register data, MSB first */
 	for (j = 0; j < 16; j++) {
-		MDC (0);
+		bus->set_mdc (bus, 0);
 		if ((value & 0x00008000) == 0) {
-			MDIO (0);
+			bus->set_mdio (bus, 0);
 		} else {
-			MDIO (1);
+			bus->set_mdio (bus, 1);
 		}
-		MIIDELAY;
-		MDC (1);
-		MIIDELAY;
+		bus->delay(bus);
+		bus->set_mdc (bus, 1);
+		bus->delay(bus);
 		value <<= 1;
 	}
 
 	/*
 	 * Tri-state the MDIO line.
 	 */
-	MDIO_TRISTATE;
-	MDC (0);
-	MIIDELAY;
-	MDC (1);
-	MIIDELAY;
+	bus->mdio_tristate(bus);
+	bus->set_mdc (bus, 0);
+	bus->delay(bus);
+	bus->set_mdc (bus, 1);
+	bus->delay(bus);
 
 	return 0;
-}
+}
\ No newline at end of file
diff --git a/include/miiphy.h b/include/miiphy.h
index fa33ec7..478c050 100644
--- a/include/miiphy.h
+++ b/include/miiphy.h
@@ -19,6 +19,8 @@
 |
 |	COPYRIGHT   I B M   CORPORATION 1999
 |	LICENSED MATERIAL  -  PROGRAM PROPERTY OF I B M
+|
+|   Additions (C) Copyright 2009 Industrie Dial Face S.p.A.
 +----------------------------------------------------------------------------*/
 /*----------------------------------------------------------------------------+
 |
@@ -61,12 +63,32 @@ char *miiphy_get_current_dev (void);
 
 void miiphy_listdev (void);
 
+#ifdef CONFIG_BITBANGMII
+
 #define BB_MII_DEVNAME	"bbmii"
 
+struct bbmiibus {
+	char name[NAMESIZE];
+	int (*init)(struct bbmiibus *bus);
+	int (*mdio_active)(struct bbmiibus *bus);
+	int (*mdio_tristate)(struct bbmiibus *bus);
+	int (*set_mdio)(struct bbmiibus *bus, int v);
+	int (*get_mdio)(struct bbmiibus *bus, int *v);
+	int (*set_mdc)(struct bbmiibus *bus, int v);
+	int (*delay)(struct bbmiibus *bus);
+#ifdef CONFIG_BITBANGMII_MULTI
+	void *priv;
+#endif
+};
+
+extern struct bbmiibus bbmiibusses[];
+
+void bb_miiphy_init (void);
 int bb_miiphy_read (char *devname, unsigned char addr,
 		    unsigned char reg, unsigned short *value);
 int bb_miiphy_write (char *devname, unsigned char addr,
 		     unsigned char reg, unsigned short value);
+#endif
 
 /* phy seed setup */
 #define AUTO			99
-- 
1.6.3.3

[U-Boot] [PATCH 2/3] Add bb_miiphy_init call before any ethernet bring-up code.

[Luigi 'Comio' Mantellini]

From: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>

Signed-off-by: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
---
 lib_arm/board.c      |    3 +++
 lib_avr32/board.c    |    3 +++
 lib_blackfin/board.c |    3 +++
 lib_i386/board.c     |    3 +++
 lib_m68k/board.c     |    3 +++
 lib_mips/board.c     |    3 +++
 lib_ppc/board.c      |    4 +++-
 lib_sh/board.c       |    3 +++
 lib_sparc/board.c    |    3 +++
 9 files changed, 27 insertions(+), 1 deletions(-)

diff --git a/lib_arm/board.c b/lib_arm/board.c
index a0e56d5..6e77468 100644
--- a/lib_arm/board.c
+++ b/lib_arm/board.c
@@ -417,6 +417,9 @@ extern void davinci_eth_set_mac_addr (const u_int8_t *addr);
 	mmc_initialize (gd->bd);
 #endif
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 #if defined(CONFIG_NET_MULTI)
 	puts ("Net:   ");
diff --git a/lib_avr32/board.c b/lib_avr32/board.c
index 29999d8..e715872 100644
--- a/lib_avr32/board.c
+++ b/lib_avr32/board.c
@@ -337,6 +337,9 @@ void board_init_r(gd_t *new_gd, ulong dest_addr)
 	if (s)
 		load_addr = simple_strtoul(s, NULL, 16);
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 	s = getenv("bootfile");
 	if (s)
diff --git a/lib_blackfin/board.c b/lib_blackfin/board.c
index 1053f69..f1a7479 100644
--- a/lib_blackfin/board.c
+++ b/lib_blackfin/board.c
@@ -270,6 +270,9 @@ void board_init_f(ulong bootflag)
 
 static void board_net_init_r(bd_t *bd)
 {
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #ifdef CONFIG_CMD_NET
 	uchar enetaddr[6];
 	char *s;
diff --git a/lib_i386/board.c b/lib_i386/board.c
index 0262b5e..821713a 100644
--- a/lib_i386/board.c
+++ b/lib_i386/board.c
@@ -351,6 +351,9 @@ void start_i386boot (void)
 	doc_init();
 #endif
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 #if defined(CONFIG_NET_MULTI)
 	WATCHDOG_RESET();
diff --git a/lib_m68k/board.c b/lib_m68k/board.c
index 3d88530..32ae592 100644
--- a/lib_m68k/board.c
+++ b/lib_m68k/board.c
@@ -630,6 +630,9 @@ void board_init_r (gd_t *id, ulong dest_addr)
 	nand_init();		/* go init the NAND */
 #endif
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 	WATCHDOG_RESET();
 #if defined(FEC_ENET)
diff --git a/lib_mips/board.c b/lib_mips/board.c
index f62a46a..fd12e68 100644
--- a/lib_mips/board.c
+++ b/lib_mips/board.c
@@ -407,6 +407,9 @@ void board_init_r (gd_t *id, ulong dest_addr)
 	misc_init_r ();
 #endif
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 #if defined(CONFIG_NET_MULTI)
 	puts ("Net:   ");
diff --git a/lib_ppc/board.c b/lib_ppc/board.c
index e8509ee..0bb159e 100644
--- a/lib_ppc/board.c
+++ b/lib_ppc/board.c
@@ -1002,6 +1002,9 @@ void board_init_r (gd_t *id, ulong dest_addr)
 	doc_init ();
 #endif
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 #if defined(CONFIG_NET_MULTI)
 	WATCHDOG_RESET ();
@@ -1009,7 +1012,6 @@ void board_init_r (gd_t *id, ulong dest_addr)
 #endif
 	eth_initialize (bd);
 #endif
-
 #if defined(CONFIG_CMD_NET) && ( \
     defined(CONFIG_CCM)		|| \
     defined(CONFIG_ELPT860)	|| \
diff --git a/lib_sh/board.c b/lib_sh/board.c
index 5d61f0d..52bbc6d 100644
--- a/lib_sh/board.c
+++ b/lib_sh/board.c
@@ -178,6 +178,9 @@ void sh_generic_init(void)
 #endif /* CONFIG_WATCHDOG*/
 
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 	{
 		char *s;
diff --git a/lib_sparc/board.c b/lib_sparc/board.c
index 6aadb56..56192a7 100644
--- a/lib_sparc/board.c
+++ b/lib_sparc/board.c
@@ -405,6 +405,9 @@ void board_init_f(ulong bootflag)
 	doc_init();
 #endif
 
+#ifdef CONFIG_BITBANGMII
+	bb_miiphy_init();
+#endif
 #if defined(CONFIG_CMD_NET)
 #if defined(CONFIG_NET_MULTI)
 	WATCHDOG_RESET();
-- 
1.6.3.3

[U-Boot] [PATCH 3/3] Update all board to support new bbmiiphy driver (with multibus support)

[Luigi 'Comio' Mantellini]

From: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>

Signed-off-by: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
---
 include/configs/ISPAN.h      |    3 +++
 include/configs/MPC8260ADS.h |    2 ++
 include/configs/MPC8266ADS.h |    3 +++
 include/configs/MPC8560ADS.h |    3 +++
 include/configs/Rattler.h    |    3 +++
 include/configs/SBC8540.h    |    3 +++
 include/configs/TQM8272.h    |    2 ++
 include/configs/VoVPN-GW.h   |    3 +++
 include/configs/ZPC1900.h    |    3 +++
 include/configs/ep8248.h     |    3 +++
 include/configs/ep82xxm.h    |    3 +++
 include/configs/gw8260.h     |    3 +++
 include/configs/hymod.h      |    9 +++++++++
 include/configs/muas3001.h   |    3 +++
 include/configs/ppmc8260.h   |    3 +++
 include/configs/sacsng.h     |    3 +++
 include/configs/sbc8260.h    |    3 +++
 include/configs/sbc8560.h    |    3 +++
 18 files changed, 58 insertions(+), 0 deletions(-)

diff --git a/include/configs/ISPAN.h b/include/configs/ISPAN.h
index 6eb466a..be41f37 100644
--- a/include/configs/ISPAN.h
+++ b/include/configs/ISPAN.h
@@ -84,6 +84,9 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT		3		/* Port D */
+#define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 
 #define CONFIG_SYS_MDIO_PIN		0x00040000	/* PD13 */
 #define CONFIG_SYS_MDC_PIN		0x00080000	/* PD12 */
diff --git a/include/configs/MPC8260ADS.h b/include/configs/MPC8260ADS.h
index 942a4cc..255b4aa 100644
--- a/include/configs/MPC8260ADS.h
+++ b/include/configs/MPC8260ADS.h
@@ -149,6 +149,8 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT	2		/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
 
 #if CONFIG_ADSTYPE == CONFIG_SYS_8272ADS
 #define CONFIG_SYS_MDIO_PIN	0x00002000	/* PC18 */
diff --git a/include/configs/MPC8266ADS.h b/include/configs/MPC8266ADS.h
index 4fd86d3..eb35fc4 100644
--- a/include/configs/MPC8266ADS.h
+++ b/include/configs/MPC8266ADS.h
@@ -95,6 +95,9 @@
  * Port pins used for bit-banged MII communictions (if applicable).
  */
 #define MDIO_PORT	2	/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
 #define MDIO_READ	((iop->pdat &  0x00400000) != 0)
diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index c1a1a6d..1b9f624 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -362,6 +362,9 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT	2		/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
 #define MDIO_READ	((iop->pdat &  0x00400000) != 0)
diff --git a/include/configs/Rattler.h b/include/configs/Rattler.h
index 5b6f271..249667c 100644
--- a/include/configs/Rattler.h
+++ b/include/configs/Rattler.h
@@ -103,6 +103,9 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT		2	/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE		(iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE		(iop->pdir &= ~0x00400000)
 #define MDIO_READ		((iop->pdat &  0x00400000) != 0)
diff --git a/include/configs/SBC8540.h b/include/configs/SBC8540.h
index 7239f84..ede7c10 100644
--- a/include/configs/SBC8540.h
+++ b/include/configs/SBC8540.h
@@ -286,6 +286,9 @@
    * GPIO pins used for bit-banged MII communications
    */
   #define MDIO_PORT	2		/* Port C */
+  #define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+  #define MDC_DECLARE	MDIO_DECLARE
+
   #define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
   #define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
   #define MDIO_READ	((iop->pdat &  0x00400000) != 0)
diff --git a/include/configs/TQM8272.h b/include/configs/TQM8272.h
index 6c462af..522e29e 100644
--- a/include/configs/TQM8272.h
+++ b/include/configs/TQM8272.h
@@ -219,6 +219,8 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT	2		/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
 
 #if STK82xx_150
 #define CONFIG_SYS_MDIO_PIN	0x00008000	/* PC16 */
diff --git a/include/configs/VoVPN-GW.h b/include/configs/VoVPN-GW.h
index b2d75e3..5c99be8 100644
--- a/include/configs/VoVPN-GW.h
+++ b/include/configs/VoVPN-GW.h
@@ -124,6 +124,9 @@
 #define CONFIG_BITBANGMII
 
 #define MDIO_PORT			1		/* Port B */
+#define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define CONFIG_SYS_MDIO_PIN			0x00002000	/* PB18 */
 #define CONFIG_SYS_MDC_PIN			0x00001000	/* PB19 */
 #define MDIO_ACTIVE			(iop->pdir |=  CONFIG_SYS_MDIO_PIN)
diff --git a/include/configs/ZPC1900.h b/include/configs/ZPC1900.h
index 9cda3f9..6c21540 100644
--- a/include/configs/ZPC1900.h
+++ b/include/configs/ZPC1900.h
@@ -86,6 +86,9 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT		2	/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE		(iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE		(iop->pdir &= ~0x00400000)
 #define MDIO_READ		((iop->pdat &  0x00400000) != 0)
diff --git a/include/configs/ep8248.h b/include/configs/ep8248.h
index cb4185a..113b040 100644
--- a/include/configs/ep8248.h
+++ b/include/configs/ep8248.h
@@ -92,6 +92,9 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT		0	/* Not used - implemented in BCSR */
+#define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE		(*(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFB)
 #define MDIO_TRISTATE		(*(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x04)
 #define MDIO_READ		(*(vu_char *)(CONFIG_SYS_BCSR + 8) & 1)
diff --git a/include/configs/ep82xxm.h b/include/configs/ep82xxm.h
index 239ff67..29fe6d5 100644
--- a/include/configs/ep82xxm.h
+++ b/include/configs/ep82xxm.h
@@ -85,6 +85,9 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT		0	/* Not used - implemented in BCSR */
+#define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE		(*(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFB)
 #define MDIO_TRISTATE		(*(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x04)
 #define MDIO_READ		(*(vu_char *)(CONFIG_SYS_BCSR + 8) & 1)
diff --git a/include/configs/gw8260.h b/include/configs/gw8260.h
index 53a001d..30a79ff 100644
--- a/include/configs/gw8260.h
+++ b/include/configs/gw8260.h
@@ -212,6 +212,9 @@
  * Port pins used for bit-banged MII communictions (if applicable).
  */
 #define MDIO_PORT   2       /* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE    (iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE  (iop->pdir &= ~0x00400000)
 #define MDIO_READ     ((iop->pdat &  0x00400000) != 0)
diff --git a/include/configs/hymod.h b/include/configs/hymod.h
index 284672b..023303a 100644
--- a/include/configs/hymod.h
+++ b/include/configs/hymod.h
@@ -93,6 +93,9 @@
 # define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB)
 
 # define MDIO_PORT		0		/* Port A */
+# define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+# define MDC_DECLARE	MDIO_DECLARE
+
 # define MDIO_DATA_PINMASK	0x00040000	/* Pin 13 */
 # define MDIO_CLCK_PINMASK	0x00080000	/* Pin 12 */
 
@@ -110,6 +113,9 @@
 # define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB)
 
 # define MDIO_PORT		0		/* Port A */
+# define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+# define MDC_DECLARE	MDIO_DECLARE
+
 # define MDIO_DATA_PINMASK	0x00000040	/* Pin 25 */
 # define MDIO_CLCK_PINMASK	0x00000080	/* Pin 24 */
 
@@ -127,6 +133,9 @@
 # define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB)
 
 # define MDIO_PORT		0		/* Port A */
+# define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+# define MDC_DECLARE	MDIO_DECLARE
+
 # define MDIO_DATA_PINMASK	0x00000100	/* Pin 23 */
 # define MDIO_CLCK_PINMASK	0x00000200	/* Pin 22 */
 
diff --git a/include/configs/muas3001.h b/include/configs/muas3001.h
index ae033b2..3228c23 100644
--- a/include/configs/muas3001.h
+++ b/include/configs/muas3001.h
@@ -101,6 +101,9 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT	0		/* Port A */
+#define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 
 #define CONFIG_SYS_MDIO_PIN	0x00200000	/* PA10 */
 #define CONFIG_SYS_MDC_PIN	0x00400000	/* PA9  */
diff --git a/include/configs/ppmc8260.h b/include/configs/ppmc8260.h
index ff7d614..3036fb7 100644
--- a/include/configs/ppmc8260.h
+++ b/include/configs/ppmc8260.h
@@ -182,6 +182,9 @@
  * Port pins used for bit-banged MII communictions (if applicable).
  */
 #define MDIO_PORT	2	/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
 #define MDIO_READ	((iop->pdat &  0x00400000) != 0)
diff --git a/include/configs/sacsng.h b/include/configs/sacsng.h
index 0ab6fc3..bfb181f 100644
--- a/include/configs/sacsng.h
+++ b/include/configs/sacsng.h
@@ -179,6 +179,9 @@
  */
 
 #define MDIO_PORT	2	        /* Port A=0, B=1, C=2, D=3 */
+#define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE	(iop->pdir |=  0x40000000)
 #define MDIO_TRISTATE	(iop->pdir &= ~0x40000000)
 #define MDIO_READ	((iop->pdat &  0x40000000) != 0)
diff --git a/include/configs/sbc8260.h b/include/configs/sbc8260.h
index 26ed557..5be1d8f 100644
--- a/include/configs/sbc8260.h
+++ b/include/configs/sbc8260.h
@@ -201,6 +201,9 @@
  * Port pins used for bit-banged MII communictions (if applicable).
  */
 #define MDIO_PORT	2	/* Port C */
+#define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+#define MDC_DECLARE		MDIO_DECLARE
+
 #define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
 #define MDIO_READ	((iop->pdat &  0x00400000) != 0)
diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h
index 4fa501d..f62d3c3 100644
--- a/include/configs/sbc8560.h
+++ b/include/configs/sbc8560.h
@@ -285,6 +285,9 @@
    * GPIO pins used for bit-banged MII communications
    */
   #define MDIO_PORT	2		/* Port C */
+  #define MDIO_DECLARE	volatile ioport_t *iop = ioport_addr ((immap_t *) CONFIG_SYS_IMMR, MDIO_PORT)
+  #define MDC_DECLARE	MDIO_DECLARE
+
   #define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
   #define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
   #define MDIO_READ	((iop->pdat &  0x00400000) != 0)
-- 
1.6.3.3