* [U-Boot] [PATCH 6/8] OMAP3 beagle Add usbtty configuration
2009-09-04 20:12 ` [U-Boot] [PATCH 5/8] OMAP3 zoom1 Add usbtty configuration Tom Rix
@ 2009-09-04 20:12 ` Tom Rix
2009-09-05 0:26 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 1 reply; 7+ messages in thread
From: Tom Rix @ 2009-09-04 20:12 UTC (permalink / raw)
To: u-boot
The primary console of beagle is the serial header.
A secondary console is to use the usbtty. The user can set this
manually by doing
setenv stdout usbtty; setenv stdin usbtty; setenv stderr usbtty
saveenv
usbtty will be usable by accessing the /dev/ttyACM0 on a linux host.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
---
include/configs/omap3_beagle.h | 16 ++++++++++++++++
1 files changed, 16 insertions(+), 0 deletions(-)
diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index 61629f8..dc07934 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -98,6 +98,21 @@
#define CONFIG_OMAP3_MMC 1
#define CONFIG_DOS_PARTITION 1
+/* USB */
+#define CONFIG_MUSB_UDC 1
+#define CONFIG_USB_OMAP3 1
+#define CONFIG_TWL4030_USB 1
+
+/* USB device configuration */
+#define CONFIG_USB_DEVICE 1
+#define CONFIG_USB_TTY 1
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
+/* Change these to suit your needs */
+#define CONFIG_USBD_VENDORID 0x0451
+#define CONFIG_USBD_PRODUCTID 0x5678
+#define CONFIG_USBD_MANUFACTURER "Texas Instruments"
+#define CONFIG_USBD_PRODUCT_NAME "Beagle"
+
/* commands to include */
#include <config_cmd_default.h>
@@ -163,6 +178,7 @@
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x82000000\0" \
+ "usbtty=cdc_acm\0" \
"console=ttyS2,115200n8\0" \
"videomode=1024x768 at 60,vxres=1024,vyres=768\0" \
"videospec=omapfb:vram:2M,vram:4M\0" \
--
1.6.0.4
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH 6/8] OMAP3 beagle Add usbtty configuration
2009-09-04 20:12 ` [U-Boot] [PATCH 6/8] OMAP3 beagle " Tom Rix
@ 2009-09-05 0:26 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 7+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2009-09-05 0:26 UTC (permalink / raw)
To: u-boot
On 15:12 Fri 04 Sep , Tom Rix wrote:
> The primary console of beagle is the serial header.
>
> A secondary console is to use the usbtty. The user can set this
> manually by doing
>
> setenv stdout usbtty; setenv stdin usbtty; setenv stderr usbtty
> saveenv
>
> usbtty will be usable by accessing the /dev/ttyACM0 on a linux host.
>
> Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
> ---
> include/configs/omap3_beagle.h | 16 ++++++++++++++++
> 1 files changed, 16 insertions(+), 0 deletions(-)
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Best Regards,
J.
^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH 6/8] OMAP3 beagle Add usbtty configuration
2009-09-28 16:35 ` [U-Boot] [PATCH 5/8] OMAP3 zoom1 Add usbtty configuration y at windriver.com
@ 2009-09-28 16:35 ` y at windriver.com
0 siblings, 0 replies; 7+ messages in thread
From: y at windriver.com @ 2009-09-28 16:35 UTC (permalink / raw)
To: u-boot
From: Tom Rix <Tom.Rix@windriver.com>
The primary console of beagle is the serial header.
A secondary console is to use the usbtty. The user can set this
manually by doing
setenv stdout usbtty; setenv stdin usbtty; setenv stderr usbtty
saveenv
usbtty will be usable by accessing the /dev/ttyACM0 on a linux host.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
---
include/configs/omap3_beagle.h | 16 ++++++++++++++++
1 files changed, 16 insertions(+), 0 deletions(-)
diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index 55eeb94..253cdba 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -98,6 +98,21 @@
#define CONFIG_OMAP3_MMC 1
#define CONFIG_DOS_PARTITION 1
+/* USB */
+#define CONFIG_MUSB_UDC 1
+#define CONFIG_USB_OMAP3 1
+#define CONFIG_TWL4030_USB 1
+
+/* USB device configuration */
+#define CONFIG_USB_DEVICE 1
+#define CONFIG_USB_TTY 1
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
+/* Change these to suit your needs */
+#define CONFIG_USBD_VENDORID 0x0451
+#define CONFIG_USBD_PRODUCTID 0x5678
+#define CONFIG_USBD_MANUFACTURER "Texas Instruments"
+#define CONFIG_USBD_PRODUCT_NAME "Beagle"
+
/* commands to include */
#include <config_cmd_default.h>
@@ -164,6 +179,7 @@
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x82000000\0" \
+ "usbtty=cdc_acm\0" \
"console=ttyS2,115200n8\0" \
"videomode=1024x768 at 60,vxres=1024,vyres=768\0" \
"videospec=omapfb:vram:2M,vram:4M\0" \
--
1.6.0.6
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH 6/8] OMAP3 beagle Add usbtty configuration
2009-09-28 16:37 ` [U-Boot] [PATCH 5/8] OMAP3 zoom1 Add usbtty configuration Tom Rix
@ 2009-09-28 16:37 ` Tom Rix
0 siblings, 0 replies; 7+ messages in thread
From: Tom Rix @ 2009-09-28 16:37 UTC (permalink / raw)
To: u-boot
The primary console of beagle is the serial header.
A secondary console is to use the usbtty. The user can set this
manually by doing
setenv stdout usbtty; setenv stdin usbtty; setenv stderr usbtty
saveenv
usbtty will be usable by accessing the /dev/ttyACM0 on a linux host.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
---
include/configs/omap3_beagle.h | 16 ++++++++++++++++
1 files changed, 16 insertions(+), 0 deletions(-)
diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index 55eeb94..253cdba 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -98,6 +98,21 @@
#define CONFIG_OMAP3_MMC 1
#define CONFIG_DOS_PARTITION 1
+/* USB */
+#define CONFIG_MUSB_UDC 1
+#define CONFIG_USB_OMAP3 1
+#define CONFIG_TWL4030_USB 1
+
+/* USB device configuration */
+#define CONFIG_USB_DEVICE 1
+#define CONFIG_USB_TTY 1
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
+/* Change these to suit your needs */
+#define CONFIG_USBD_VENDORID 0x0451
+#define CONFIG_USBD_PRODUCTID 0x5678
+#define CONFIG_USBD_MANUFACTURER "Texas Instruments"
+#define CONFIG_USBD_PRODUCT_NAME "Beagle"
+
/* commands to include */
#include <config_cmd_default.h>
@@ -164,6 +179,7 @@
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x82000000\0" \
+ "usbtty=cdc_acm\0" \
"console=ttyS2,115200n8\0" \
"videomode=1024x768 at 60,vxres=1024,vyres=768\0" \
"videospec=omapfb:vram:2M,vram:4M\0" \
--
1.6.0.6
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH 6/8] OMAP3 beagle Add usbtty configuration
[not found] <19F8576C6E063C45BE387C64729E73940436E5F620@dbde02.ent.ti.com>
@ 2009-10-27 5:25 ` Gupta, Ajay Kumar
2009-10-27 14:07 ` Tom
0 siblings, 1 reply; 7+ messages in thread
From: Gupta, Ajay Kumar @ 2009-10-27 5:25 UTC (permalink / raw)
To: u-boot
Tom,
> From: Tom Rix <Tom.Rix <at> windriver.com>
> Subject: [PATCH 6/8] OMAP3 beagle Add usbtty configuration
> Newsgroups: gmane.comp.boot-loaders.u-boot
> Date: 2009-09-28 16:37:27 GMT (4 weeks, 12 hours and 41 minutes ago)
>
> The primary console of beagle is the serial header.
>
> A secondary console is to use the usbtty. The user can set this
> manually by doing
>
> setenv stdout usbtty; setenv stdin usbtty; setenv stderr usbtty
> saveenv
>
> usbtty will be usable by accessing the /dev/ttyACM0 on a linux host.
>
> Signed-off-by: Tom Rix <Tom.Rix <at> windriver.com>
> ---
> include/configs/omap3_beagle.h | 16 ++++++++++++++++
> 1 files changed, 16 insertions(+), 0 deletions(-)
>
> diff --git a/include/configs/omap3_beagle.h
> b/include/configs/omap3_beagle.h
> index 55eeb94..253cdba 100644
> --- a/include/configs/omap3_beagle.h
> +++ b/include/configs/omap3_beagle.h
> @@ -98,6 +98,21 @@
> #define CONFIG_OMAP3_MMC 1
> #define CONFIG_DOS_PARTITION 1
>
> +/* USB */
> +#define CONFIG_MUSB_UDC 1
> +#define CONFIG_USB_OMAP3 1
> +#define CONFIG_TWL4030_USB 1
> +
> +/* USB device configuration */
> +#define CONFIG_USB_DEVICE 1
> +#define CONFIG_USB_TTY 1
> +#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
> +/* Change these to suit your needs */
> +#define CONFIG_USBD_VENDORID 0x0451
> +#define CONFIG_USBD_PRODUCTID 0x5678
> +#define CONFIG_USBD_MANUFACTURER "Texas Instruments"
> +#define CONFIG_USBD_PRODUCT_NAME "Beagle"
> +
We can either define CONFIG_MUSB_UDC or CONFIG_MUSB_HCD (host support), so I think it's better to move host and device specific definitions within
CONFIG_MUSB_UDC or CONFIG_MUSB_HCD.
#ifdef CONFIG_USB_OMAP3
#ifdef CONFIG_MUSB_HCD
<here define all host specific definitions>
#endif
#ifdef CONFIG_MUSB_UDC
<here define all device specific definitions>
#endif
#endif /* CONFIG_USB_OMAP3 */
This change would make it easier to test Host or device functionalities.
-Ajay
> /* commands to include */
> #include <config_cmd_default.h>
>
> @@ -164,6 +179,7 @@
>
> #define CONFIG_EXTRA_ENV_SETTINGS \
> "loadaddr=0x82000000\0" \
> + "usbtty=cdc_acm\0" \
> "console=ttyS2,115200n8\0" \
> "videomode=1024x768 <at> 60,vxres=1024,vyres=768\0" \
> "videospec=omapfb:vram:2M,vram:4M\0" \
> --
> 1.6.0.6
^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH 6/8] OMAP3 beagle Add usbtty configuration
2009-10-27 5:25 ` [U-Boot] [PATCH 6/8] OMAP3 beagle Add usbtty configuration Gupta, Ajay Kumar
@ 2009-10-27 14:07 ` Tom
2009-10-28 8:52 ` Gupta, Ajay Kumar
0 siblings, 1 reply; 7+ messages in thread
From: Tom @ 2009-10-27 14:07 UTC (permalink / raw)
To: u-boot
Gupta, Ajay Kumar wrote:
> Tom,
>> From: Tom Rix <Tom.Rix <at> windriver.com>
>> Subject: [PATCH 6/8] OMAP3 beagle Add usbtty configuration
>> Newsgroups: gmane.comp.boot-loaders.u-boot
>> Date: 2009-09-28 16:37:27 GMT (4 weeks, 12 hours and 41 minutes ago)
>>
>> The primary console of beagle is the serial header.
>>
>> A secondary console is to use the usbtty. The user can set this
>> manually by doing
>>
>> setenv stdout usbtty; setenv stdin usbtty; setenv stderr usbtty
>> saveenv
>>
>> usbtty will be usable by accessing the /dev/ttyACM0 on a linux host.
>>
>> Signed-off-by: Tom Rix <Tom.Rix <at> windriver.com>
>> ---
>> include/configs/omap3_beagle.h | 16 ++++++++++++++++
>> 1 files changed, 16 insertions(+), 0 deletions(-)
>>
>> diff --git a/include/configs/omap3_beagle.h
>> b/include/configs/omap3_beagle.h
>> index 55eeb94..253cdba 100644
>> --- a/include/configs/omap3_beagle.h
>> +++ b/include/configs/omap3_beagle.h
>> @@ -98,6 +98,21 @@
>> #define CONFIG_OMAP3_MMC 1
>> #define CONFIG_DOS_PARTITION 1
>>
>> +/* USB */
>> +#define CONFIG_MUSB_UDC 1
>> +#define CONFIG_USB_OMAP3 1
>> +#define CONFIG_TWL4030_USB 1
>> +
>> +/* USB device configuration */
>> +#define CONFIG_USB_DEVICE 1
>> +#define CONFIG_USB_TTY 1
>> +#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
>> +/* Change these to suit your needs */
>> +#define CONFIG_USBD_VENDORID 0x0451
>> +#define CONFIG_USBD_PRODUCTID 0x5678
>> +#define CONFIG_USBD_MANUFACTURER "Texas Instruments"
>> +#define CONFIG_USBD_PRODUCT_NAME "Beagle"
>> +
>
> We can either define CONFIG_MUSB_UDC or CONFIG_MUSB_HCD (host support), so I think it's better to move host and device specific definitions within
> CONFIG_MUSB_UDC or CONFIG_MUSB_HCD.
>
> #ifdef CONFIG_USB_OMAP3
>
> #ifdef CONFIG_MUSB_HCD
> <here define all host specific definitions>
> #endif
>
> #ifdef CONFIG_MUSB_UDC
> <here define all device specific definitions>
> #endif
>
> #endif /* CONFIG_USB_OMAP3 */
>
> This change would make it easier to test Host or device functionalities.
>
> -Ajay
I am not adding host support.
Tom
^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH 6/8] OMAP3 beagle Add usbtty configuration
2009-10-27 14:07 ` Tom
@ 2009-10-28 8:52 ` Gupta, Ajay Kumar
0 siblings, 0 replies; 7+ messages in thread
From: Gupta, Ajay Kumar @ 2009-10-28 8:52 UTC (permalink / raw)
To: u-boot
Tom,
> >
> > We can either define CONFIG_MUSB_UDC or CONFIG_MUSB_HCD (host support),
> so I think it's better to move host and device specific definitions within
> > CONFIG_MUSB_UDC or CONFIG_MUSB_HCD.
> >
> > #ifdef CONFIG_USB_OMAP3
> >
> > #ifdef CONFIG_MUSB_HCD
> > <here define all host specific definitions>
> > #endif
> >
> > #ifdef CONFIG_MUSB_UDC
> > <here define all device specific definitions>
> > #endif
> >
> > #endif /* CONFIG_USB_OMAP3 */
> >
> > This change would make it easier to test Host or device functionalities.
> >
> > -Ajay
>
> I am not adding host support.
Host side controller driver is already available (musb_hcd.c) and can be used by any omap3 platforms.
So I think we can add host config also for all the omap3 platforms which anyways doesn't break device functionality.
I would be submitting USB config patch for omap3_evm by today.
-Ajay
> Tom
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2009-10-28 8:52 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <19F8576C6E063C45BE387C64729E73940436E5F620@dbde02.ent.ti.com>
2009-10-27 5:25 ` [U-Boot] [PATCH 6/8] OMAP3 beagle Add usbtty configuration Gupta, Ajay Kumar
2009-10-27 14:07 ` Tom
2009-10-28 8:52 ` Gupta, Ajay Kumar
2009-09-28 16:37 [U-Boot] V2 of OMAP3 USB device Support Tom Rix
2009-09-28 16:37 ` [U-Boot] [PATCH 1/8] USB Consolidate descriptor definitions Tom Rix
2009-09-28 16:37 ` [U-Boot] [PATCH 2/8] USB add macros for debugging usb device setup Tom Rix
2009-09-28 16:37 ` [U-Boot] [PATCH 3/8] TWL4030 Add usb PHY support Tom Rix
2009-09-28 16:37 ` [U-Boot] [PATCH 4/8] OMAP3 Add usb device support Tom Rix
2009-09-28 16:37 ` [U-Boot] [PATCH 5/8] OMAP3 zoom1 Add usbtty configuration Tom Rix
2009-09-28 16:37 ` [U-Boot] [PATCH 6/8] OMAP3 beagle " Tom Rix
-- strict thread matches above, loose matches on Subject: below --
2009-09-28 16:34 [U-Boot] V2 of OMAP3 USB device Support y at windriver.com
2009-09-28 16:34 ` [U-Boot] [PATCH 1/8] USB Consolidate descriptor definitions y at windriver.com
2009-09-28 16:34 ` [U-Boot] [PATCH 2/8] USB add macros for debugging usb device setup y at windriver.com
2009-09-28 16:34 ` [U-Boot] [PATCH 3/8] TWL4030 Add usb PHY support y at windriver.com
2009-09-28 16:34 ` [U-Boot] [PATCH 4/8] OMAP3 Add usb device support y at windriver.com
2009-09-28 16:35 ` [U-Boot] [PATCH 5/8] OMAP3 zoom1 Add usbtty configuration y at windriver.com
2009-09-28 16:35 ` [U-Boot] [PATCH 6/8] OMAP3 beagle " y at windriver.com
2009-09-04 20:12 [U-Boot] [PATCH 1/8] USB Consolidate descriptor definitions Tom Rix
2009-09-04 20:12 ` [U-Boot] [PATCH 2/8] USB add macros for debugging usb device setup Tom Rix
2009-09-04 20:12 ` [U-Boot] [PATCH 3/8] TWL4030 Add usb PHY support Tom Rix
2009-09-04 20:12 ` [U-Boot] [PATCH 4/8] OMAP3 Add usb device support Tom Rix
2009-09-04 20:12 ` [U-Boot] [PATCH 5/8] OMAP3 zoom1 Add usbtty configuration Tom Rix
2009-09-04 20:12 ` [U-Boot] [PATCH 6/8] OMAP3 beagle " Tom Rix
2009-09-05 0:26 ` Jean-Christophe PLAGNIOL-VILLARD
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox