[U-Boot] [PATCH v2] OMAP3: add CM-T35 board

[Mike Rapoport <mike@compulab.co.il>]

Dear Wolfgang,

Wolfgang Denk wrote:
> Dear Mike Rapoport,
> 
> In message <1257955131-16729-1-git-send-email-mike@compulab.co.il> you wrote:
>> Add CM-T35 board support
>>
>> --
>> v2 changes:
>> - rename board config file from omap3_cm-t35.h to cm-t35.h
>> - remove SZ_xx references
>> - add MAKEALL/MAINTEINERS entries
>> --
>>
>> Signed-off-by: Mike Rapoport <mike@compulab.co.il>
> 
> The Signed-off-by: line belongs _above_ the "--" line.
> 
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -677,6 +677,10 @@ Stelian Pop <stelian.pop@leadtechdesign.com>
>>  	at91sam9263ek	ARM926EJS (AT91SAM9263 SoC)
>>  	at91sam9rlek	ARM926EJS (AT91SAM9RL SoC)
>>  
>> +Mike Rapoport <mike@compulab.co.il>
>> +
>> +	omap3_cm-t35	ARM CORTEX-A8 (OMAP3xx SoC)
> 
> Please fix the board name.
> 
>> diff --git a/board/cm-t35/cm-t35.c b/board/cm-t35/cm-t35.c
>> new file mode 100644
>> index 0000000..b3eb087
>> --- /dev/null
>> +++ b/board/cm-t35/cm-t35.c
>> +	udelay(1);
>> +	twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02,
>> +			     TWL4030_BASEADD_GPIO+0x0C);
>> +
>> +}
> 
> Delete this empty line, please (please check globally).
> 
> 
>> +++ b/board/cm-t35/cm-t35.h
> ...
>> +#define MUX_CM_T35() \
>> + /*SDRC*/\
>> + MUX_VAL(CP(SDRC_D0),		(IEN  | PTD | DIS | M0)) /*SDRC_D0*/\
> ...
> Indentation by TAB, please.
> 
>> +++ b/board/cm-t35/config.mk
>> @@ -0,0 +1,30 @@
> ...
>> +# For use with external or internal boots.
>> +TEXT_BASE = 0x80e80000
>> \ No newline at end of file
> ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> 
> Please fix.
> 
>> diff --git a/include/configs/cm-t35.h b/include/configs/cm-t35.h
>> new file mode 100755
>> index 0000000..b881112
>> --- /dev/null
>> +++ b/include/configs/cm-t35.h
> ...
>> +#ifndef __ASSEMBLY__
>> +extern struct gpmc *gpmc_cfg;
>> +extern unsigned int boot_flash_base;
>> +extern volatile unsigned int boot_flash_env_addr;
>> +extern unsigned int boot_flash_off;
>> +extern unsigned int boot_flash_sec;
>> +extern unsigned int boot_flash_type;
>> +#endif
> 
> These should not be needed in your board config file. Please move to a
> more appropriate header.

This is what all other omap3 board do... Moving these requires some rework of
common omap3 code and updates to all omap3 boards.

> 
> Best regards,
> 
> Wolfgang Denk
> 

-- 
Sincerely yours,
Mike.