* [U-Boot] [PATCH] samsung: fix DMC1_MEM_CFG for s3c64xx @ 2009-11-28 1:26 "Seunghyeon Rhee (이승현)" 2009-12-02 4:49 ` Minkyu Kang 0 siblings, 1 reply; 8+ messages in thread From: "Seunghyeon Rhee (이승현)" @ 2009-11-28 1:26 UTC (permalink / raw) To: u-boot The MSB of DMC1_MEM_CFG can be set to '1' for separate CKE control for S3C6400. In the configuration of SMDK6400, however, two 16-bit mDDR (SAMSUNG K4X51163) chips are used in parallel to form 32-bit memory bus and there is no need to contorl CKE for each chip separately. AFAIK, CKE1 is not at all connected. Only CKE0 is used. Futhermore, it should be '0' always for S3C6410. When tested with a board which has a S3C6410 and the same memory configuration, a side effect is obsearved that u-boot command "reset" doesn't work leading to system hang. Leaving the bit clear is safe in most cases. Signed-off-by: Seunghyeon Rhee <seunghyeon@lpmtec.com> --- include/s3c6400.h | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-) diff --git a/include/s3c6400.h b/include/s3c6400.h index e527c08..7229ea6 100644 --- a/include/s3c6400.h +++ b/include/s3c6400.h @@ -817,7 +817,7 @@ /*----------------------------------------------------------------------- * Physical Memory Map */ -#define DMC1_MEM_CFG 0x80010012 /* Chip1, Burst4, Row/Column bit */ +#define DMC1_MEM_CFG 0x00010012 /* Chip1, Burst4, Row/Column bit */ #define DMC1_MEM_CFG2 0xB45 #define DMC1_CHIP0_CFG 0x150F8 /* 0x4000_0000 ~ 0x43ff_ffff (64MB) */ #define DMC_DDR_32_CFG 0x0 /* 32bit, DDR */ -- 1.6.2.5 -- Seunghyeon Rhee, Ph.D. / Director LPM Technology Inc. T +82-70-8255-6007 F +82-2-6442-6462 M +82-10-2790-0657 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH] samsung: fix DMC1_MEM_CFG for s3c64xx 2009-11-28 1:26 [U-Boot] [PATCH] samsung: fix DMC1_MEM_CFG for s3c64xx "Seunghyeon Rhee (이승현)" @ 2009-12-02 4:49 ` Minkyu Kang 2009-12-02 5:32 ` Seunghyeon Rhee 2009-12-03 0:41 ` [U-Boot] [PATCH (repost)] " Seunghyeon Rhee 0 siblings, 2 replies; 8+ messages in thread From: Minkyu Kang @ 2009-12-02 4:49 UTC (permalink / raw) To: u-boot Dear Seunghyeon Rhee, 2009/11/28 "Seunghyeon Rhee (???)" <seunghyeon@lpmtec.com>: > The MSB of DMC1_MEM_CFG can be set to '1' for separate CKE control > for S3C6400. In the configuration of SMDK6400, however, two 16-bit > mDDR (SAMSUNG K4X51163) chips are used in parallel to form 32-bit > memory bus and there is no need to contorl CKE for each chip > separately. AFAIK, CKE1 is not at all connected. Only CKE0 is > used. Futhermore, it should be '0' always for S3C6410. When tested > with a board which has a S3C6410 and the same memory configuration, > a side effect is obsearved that u-boot command "reset" doesn't work > leading to system hang. Leaving the bit clear is safe in most cases. > > Signed-off-by: Seunghyeon Rhee <seunghyeon@lpmtec.com> > --- > ?include/s3c6400.h | ? ?2 +- > ?1 files changed, 1 insertions(+), 1 deletions(-) > > diff --git a/include/s3c6400.h b/include/s3c6400.h > index e527c08..7229ea6 100644 > --- a/include/s3c6400.h > +++ b/include/s3c6400.h > @@ -817,7 +817,7 @@ > ?/*----------------------------------------------------------------------- > ?* Physical Memory Map > ?*/ > -#define DMC1_MEM_CFG ? 0x80010012 ? ? ?/* Chip1, Burst4, Row/Column bit */ > +#define DMC1_MEM_CFG ? 0x00010012 ? ? ?/* Chip1, Burst4, Row/Column bit */ > ?#define DMC1_MEM_CFG2 ?0xB45 > ?#define DMC1_CHIP0_CFG 0x150F8 ? ? ? ? /* 0x4000_0000 ~ 0x43ff_ffff (64MB) */ > ?#define DMC_DDR_32_CFG 0x0 ? ? ? ? ? ? /* 32bit, DDR */ > -- > 1.6.2.5 > > > -- > Seunghyeon Rhee, Ph.D. / Director > LPM Technology Inc. > T +82-70-8255-6007 ?F +82-2-6442-6462 > M +82-10-2790-0657 > Please rebase this patch. s3c6400.h is moved to include/asm-arm/arch-s3c64xx/s3c6400.h Thanks Minkyu Kang -- from. prom. www.promsoft.net ^ permalink raw reply [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH] samsung: fix DMC1_MEM_CFG for s3c64xx 2009-12-02 4:49 ` Minkyu Kang @ 2009-12-02 5:32 ` Seunghyeon Rhee 2009-12-03 0:41 ` [U-Boot] [PATCH (repost)] " Seunghyeon Rhee 1 sibling, 0 replies; 8+ messages in thread From: Seunghyeon Rhee @ 2009-12-02 5:32 UTC (permalink / raw) To: u-boot Minkyu Kang ? ?: > Dear Seunghyeon Rhee, > > 2009/11/28 "Seunghyeon Rhee (???)" <seunghyeon@lpmtec.com>: > >> The MSB of DMC1_MEM_CFG can be set to '1' for separate CKE control >> for S3C6400. In the configuration of SMDK6400, however, two 16-bit >> mDDR (SAMSUNG K4X51163) chips are used in parallel to form 32-bit >> memory bus and there is no need to contorl CKE for each chip >> separately. AFAIK, CKE1 is not at all connected. Only CKE0 is >> used. Futhermore, it should be '0' always for S3C6410. When tested >> with a board which has a S3C6410 and the same memory configuration, >> a side effect is obsearved that u-boot command "reset" doesn't work >> leading to system hang. Leaving the bit clear is safe in most cases. >> >> Signed-off-by: Seunghyeon Rhee <seunghyeon@lpmtec.com> >> --- >> include/s3c6400.h | 2 +- >> 1 files changed, 1 insertions(+), 1 deletions(-) >> >> diff --git a/include/s3c6400.h b/include/s3c6400.h >> index e527c08..7229ea6 100644 >> --- a/include/s3c6400.h >> +++ b/include/s3c6400.h >> @@ -817,7 +817,7 @@ >> /*----------------------------------------------------------------------- >> * Physical Memory Map >> */ >> -#define DMC1_MEM_CFG 0x80010012 /* Chip1, Burst4, Row/Column bit */ >> +#define DMC1_MEM_CFG 0x00010012 /* Chip1, Burst4, Row/Column bit */ >> #define DMC1_MEM_CFG2 0xB45 >> #define DMC1_CHIP0_CFG 0x150F8 /* 0x4000_0000 ~ 0x43ff_ffff (64MB) */ >> #define DMC_DDR_32_CFG 0x0 /* 32bit, DDR */ >> -- >> 1.6.2.5 >> >> >> -- >> Seunghyeon Rhee, Ph.D. / Director >> LPM Technology Inc. >> T +82-70-8255-6007 F +82-2-6442-6462 >> M +82-10-2790-0657 >> >> > > Please rebase this patch. > s3c6400.h is moved to include/asm-arm/arch-s3c64xx/s3c6400.h > > Thanks > Minkyu Kang > The MSB of DMC1_MEM_CFG can be set to '1' for separate CKE control for S3C6400. In the configuration of SMDK6400, however, two 16-bit mDDR (SAMSUNG K4X51163) chips are used in parallel to form 32-bit memory bus and there is no need to control CKE for each chip separately. AFAIK, CKE1 is not at all connected. Only CKE0 is used. Futhermore, it should be '0' always for S3C6410. When tested with a board which has a S3C6410 and the same memory configuration, a side effect is observed that u-boot command "reset" doesn't work leading to system hang. Leaving the bit clear is safe in most cases. Signed-off-by: Seunghyeon Rhee <seunghyeon@lpmtec.com> --- include/asm-arm/arch-s3c64xx/s3c6400.h | 4 ++-- 1 files changed, 2 insertions(+), 2 deletions(-) diff --git a/include/asm-arm/arch-s3c64xx/s3c6400.h b/include/asm-arm/arch-s3c64xx/s3c6400.h index e527c08..10b3324 100644 --- a/include/asm-arm/arch-s3c64xx/s3c6400.h +++ b/include/asm-arm/arch-s3c64xx/s3c6400.h @@ -817,9 +817,9 @@ /*----------------------------------------------------------------------- * Physical Memory Map */ -#define DMC1_MEM_CFG 0x80010012 /* Chip1, Burst4, Row/Column bit */ +#define DMC1_MEM_CFG 0x00010012 /* burst 4, 13-bit row, 10-bit col */ #define DMC1_MEM_CFG2 0xB45 -#define DMC1_CHIP0_CFG 0x150F8 /* 0x4000_0000 ~ 0x43ff_ffff (64MB) */ +#define DMC1_CHIP0_CFG 0x150F8 /* 0x5000_0000~0x57ff_ffff (128 MiB) */ #define DMC_DDR_32_CFG 0x0 /* 32bit, DDR */ /* Memory Parameters */ -- 1.6.2.5 Seunghyeon Rhee, Ph.D. / Director LPM Technology Inc. T +82-70-8255-6007 F +82-2-6442-6462 M +82-10-2790-0657 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH (repost)] samsung: fix DMC1_MEM_CFG for s3c64xx 2009-12-02 4:49 ` Minkyu Kang 2009-12-02 5:32 ` Seunghyeon Rhee @ 2009-12-03 0:41 ` Seunghyeon Rhee 2009-12-04 0:16 ` Minkyu Kang 2009-12-05 0:56 ` Wolfgang Denk 1 sibling, 2 replies; 8+ messages in thread From: Seunghyeon Rhee @ 2009-12-03 0:41 UTC (permalink / raw) To: u-boot Minkyu Kang worte: > Dear Seunghyeon Rhee, > > 2009/11/28 "Seunghyeon Rhee" <seunghyeon@lpmtec.com>: > >> The MSB of DMC1_MEM_CFG can be set to '1' for separate CKE control >> for S3C6400. In the configuration of SMDK6400, however, two 16-bit >> mDDR (SAMSUNG K4X51163) chips are used in parallel to form 32-bit >> memory bus and there is no need to contorl CKE for each chip >> separately. AFAIK, CKE1 is not at all connected. Only CKE0 is >> used. Futhermore, it should be '0' always for S3C6410. When tested >> with a board which has a S3C6410 and the same memory configuration, >> a side effect is obsearved that u-boot command "reset" doesn't work >> leading to system hang. Leaving the bit clear is safe in most cases. >> >> Signed-off-by: Seunghyeon Rhee <seunghyeon@lpmtec.com> >> --- >> include/s3c6400.h | 2 +- >> 1 files changed, 1 insertions(+), 1 deletions(-) >> >> diff --git a/include/s3c6400.h b/include/s3c6400.h >> index e527c08..7229ea6 100644 >> --- a/include/s3c6400.h >> +++ b/include/s3c6400.h >> @@ -817,7 +817,7 @@ >> /*----------------------------------------------------------------------- >> * Physical Memory Map >> */ >> -#define DMC1_MEM_CFG 0x80010012 /* Chip1, Burst4, Row/Column bit */ >> +#define DMC1_MEM_CFG 0x00010012 /* Chip1, Burst4, Row/Column bit */ >> #define DMC1_MEM_CFG2 0xB45 >> #define DMC1_CHIP0_CFG 0x150F8 /* 0x4000_0000 ~ 0x43ff_ffff (64MB) */ >> #define DMC_DDR_32_CFG 0x0 /* 32bit, DDR */ >> -- >> 1.6.2.5 >> >> >> -- >> Seunghyeon Rhee, Ph.D. / Director >> LPM Technology Inc. >> T +82-70-8255-6007 F +82-2-6442-6462 >> M +82-10-2790-0657 >> >> > > Please rebase this patch. > s3c6400.h is moved to include/asm-arm/arch-s3c64xx/s3c6400.h > > Thanks > Minkyu Kang > The MSB of DMC1_MEM_CFG can be set to '1' for separate CKE control for S3C6400. In the configuration of SMDK6400, however, two 16-bit mDDR (SAMSUNG K4X51163) chips are used in parallel to form 32-bit memory bus and there is no need to control CKE for each chip separately. AFAIK, CKE1 is not at all connected. Only CKE0 is used. Futhermore, it should be '0' always for S3C6410. When tested with a board which has a S3C6410 and the same memory configuration, a side effect is observed that u-boot command "reset" doesn't work leading to system hang. Leaving the bit clear is safe in most cases. Signed-off-by: Seunghyeon Rhee <seunghyeon@lpmtec.com> --- include/asm-arm/arch-s3c64xx/s3c6400.h | 4 ++-- 1 files changed, 2 insertions(+), 2 deletions(-) diff --git a/include/asm-arm/arch-s3c64xx/s3c6400.h b/include/asm-arm/arch-s3c64xx/s3c6400.h index e527c08..10b3324 100644 --- a/include/asm-arm/arch-s3c64xx/s3c6400.h +++ b/include/asm-arm/arch-s3c64xx/s3c6400.h @@ -817,9 +817,9 @@ /*----------------------------------------------------------------------- * Physical Memory Map */ -#define DMC1_MEM_CFG 0x80010012 /* Chip1, Burst4, Row/Column bit */ +#define DMC1_MEM_CFG 0x00010012 /* burst 4, 13-bit row, 10-bit col */ #define DMC1_MEM_CFG2 0xB45 -#define DMC1_CHIP0_CFG 0x150F8 /* 0x4000_0000 ~ 0x43ff_ffff (64MB) */ +#define DMC1_CHIP0_CFG 0x150F8 /* 0x5000_0000~0x57ff_ffff (128 MiB) */ #define DMC_DDR_32_CFG 0x0 /* 32bit, DDR */ /* Memory Parameters */ -- 1.6.2.5 Seunghyeon Rhee, Ph.D. / Director LPM Technology Inc. T +82-70-8255-6007 F +82-2-6442-6462 M +82-10-2790-0657 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH (repost)] samsung: fix DMC1_MEM_CFG for s3c64xx 2009-12-03 0:41 ` [U-Boot] [PATCH (repost)] " Seunghyeon Rhee @ 2009-12-04 0:16 ` Minkyu Kang 2009-12-05 0:59 ` Wolfgang Denk 2009-12-05 0:56 ` Wolfgang Denk 1 sibling, 1 reply; 8+ messages in thread From: Minkyu Kang @ 2009-12-04 0:16 UTC (permalink / raw) To: u-boot Dear Seunghyyeon Rhee, 2009/12/3 Seunghyeon Rhee <seunghyeon@lpmtec.com>: > Minkyu Kang worte: >> Dear Seunghyeon Rhee, >> >> 2009/11/28 "Seunghyeon Rhee" <seunghyeon@lpmtec.com>: >> >>> The MSB of DMC1_MEM_CFG can be set to '1' for separate CKE control >>> for S3C6400. In the configuration of SMDK6400, however, two 16-bit >>> mDDR (SAMSUNG K4X51163) chips are used in parallel to form 32-bit >>> memory bus and there is no need to contorl CKE for each chip >>> separately. AFAIK, CKE1 is not at all connected. Only CKE0 is >>> used. Futhermore, it should be '0' always for S3C6410. When tested >>> with a board which has a S3C6410 and the same memory configuration, >>> a side effect is obsearved that u-boot command "reset" doesn't work >>> leading to system hang. Leaving the bit clear is safe in most cases. >>> >>> Signed-off-by: Seunghyeon Rhee <seunghyeon@lpmtec.com> >>> --- >>> ?include/s3c6400.h | ? ?2 +- >>> ?1 files changed, 1 insertions(+), 1 deletions(-) >>> >>> diff --git a/include/s3c6400.h b/include/s3c6400.h >>> index e527c08..7229ea6 100644 >>> --- a/include/s3c6400.h >>> +++ b/include/s3c6400.h >>> @@ -817,7 +817,7 @@ >>> ?/*----------------------------------------------------------------------- >>> ?* Physical Memory Map >>> ?*/ >>> -#define DMC1_MEM_CFG ? 0x80010012 ? ? ?/* Chip1, Burst4, Row/Column bit */ >>> +#define DMC1_MEM_CFG ? 0x00010012 ? ? ?/* Chip1, Burst4, Row/Column bit */ >>> ?#define DMC1_MEM_CFG2 ?0xB45 >>> ?#define DMC1_CHIP0_CFG 0x150F8 ? ? ? ? /* 0x4000_0000 ~ 0x43ff_ffff (64MB) */ >>> ?#define DMC_DDR_32_CFG 0x0 ? ? ? ? ? ? /* 32bit, DDR */ >>> -- >>> 1.6.2.5 >>> >>> >>> -- >>> Seunghyeon Rhee, Ph.D. / Director >>> LPM Technology Inc. >>> T +82-70-8255-6007 ?F +82-2-6442-6462 >>> M +82-10-2790-0657 >>> >>> >> >> Please rebase this patch. >> s3c6400.h is moved to include/asm-arm/arch-s3c64xx/s3c6400.h >> >> Thanks >> Minkyu Kang >> > > The MSB of DMC1_MEM_CFG can be set to '1' for separate CKE control > for S3C6400. In the configuration of SMDK6400, however, two 16-bit > mDDR (SAMSUNG K4X51163) chips are used in parallel to form 32-bit > memory bus and there is no need to control CKE for each chip > separately. AFAIK, CKE1 is not at all connected. Only CKE0 is > used. Futhermore, it should be '0' always for S3C6410. When tested > with a board which has a S3C6410 and the same memory configuration, > a side effect is observed that u-boot command "reset" doesn't work > leading to system hang. Leaving the bit clear is safe in most cases. > > Signed-off-by: Seunghyeon Rhee <seunghyeon@lpmtec.com> > --- > ?include/asm-arm/arch-s3c64xx/s3c6400.h | ? ?4 ++-- > ?1 files changed, 2 insertions(+), 2 deletions(-) > > diff --git a/include/asm-arm/arch-s3c64xx/s3c6400.h b/include/asm-arm/arch-s3c64xx/s3c6400.h > index e527c08..10b3324 100644 > --- a/include/asm-arm/arch-s3c64xx/s3c6400.h > +++ b/include/asm-arm/arch-s3c64xx/s3c6400.h > @@ -817,9 +817,9 @@ > ?/*----------------------------------------------------------------------- > ?* Physical Memory Map > ?*/ > -#define DMC1_MEM_CFG ? 0x80010012 ? ? ?/* Chip1, Burst4, Row/Column bit */ > +#define DMC1_MEM_CFG ? 0x00010012 ? ? ?/* burst 4, 13-bit row, 10-bit col */ > ?#define DMC1_MEM_CFG2 ?0xB45 > -#define DMC1_CHIP0_CFG 0x150F8 ? ? ? ? /* 0x4000_0000 ~ 0x43ff_ffff (64MB) */ > +#define DMC1_CHIP0_CFG 0x150F8 ? ? ? ? /* 0x5000_0000~0x57ff_ffff (128 MiB) */ > ?#define DMC_DDR_32_CFG 0x0 ? ? ? ? ? ? /* 32bit, DDR */ > > ?/* Memory Parameters */ > -- > 1.6.2.5 > > > Seunghyeon Rhee, Ph.D. / Director > LPM Technology Inc. > T +82-70-8255-6007 ?F +82-2-6442-6462 > M +82-10-2790-0657 > applied to u-boot-samsung Thanks Minkyu Kang -- from. prom. www.promsoft.net ^ permalink raw reply [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH (repost)] samsung: fix DMC1_MEM_CFG for s3c64xx 2009-12-04 0:16 ` Minkyu Kang @ 2009-12-05 0:59 ` Wolfgang Denk 2009-12-05 2:52 ` Minkyu Kang 0 siblings, 1 reply; 8+ messages in thread From: Wolfgang Denk @ 2009-12-05 0:59 UTC (permalink / raw) To: u-boot Dear Minkyu Kang, In message <1f3430fb0912031616t6910a3d9yce8621afe0631e18@mail.gmail.com> you wrote: > ... > applied to u-boot-samsung Thanks for clean9ing up the original poster's mess of a commit message. But please feel free to reject such horribly formatted submissions. Best regards, Wolfgang Denk -- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Der Irrtum wiederholt sich immerfort in der Tat. Deshalb mu? man das Wahre unerm?dlich in Worten wiederholen. - Goethe ^ permalink raw reply [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH (repost)] samsung: fix DMC1_MEM_CFG for s3c64xx 2009-12-05 0:59 ` Wolfgang Denk @ 2009-12-05 2:52 ` Minkyu Kang 0 siblings, 0 replies; 8+ messages in thread From: Minkyu Kang @ 2009-12-05 2:52 UTC (permalink / raw) To: u-boot Dear Wolfgang, 2009/12/5 Wolfgang Denk <wd@denx.de>: > Dear Minkyu Kang, > > In message <1f3430fb0912031616t6910a3d9yce8621afe0631e18@mail.gmail.com> you wrote: >> > ... >> applied to u-boot-samsung > > Thanks for clean9ing up the original poster's mess of a commit > message. But please feel free to reject such horribly formatted > submissions. Ok. I will. Thanks in advice. > > Best regards, > > Wolfgang Denk > > -- > DENX Software Engineering GmbH, ? ? MD: Wolfgang Denk & Detlev Zundel > HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany > Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de > Der Irrtum wiederholt sich immerfort in der Tat. ?Deshalb mu? man das > Wahre unerm?dlich in Worten wiederholen. ? ? ? ? ? ? ? ? ? ? - Goethe > Minkyu Kang -- from. prom. www.promsoft.net ^ permalink raw reply [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH (repost)] samsung: fix DMC1_MEM_CFG for s3c64xx 2009-12-03 0:41 ` [U-Boot] [PATCH (repost)] " Seunghyeon Rhee 2009-12-04 0:16 ` Minkyu Kang @ 2009-12-05 0:56 ` Wolfgang Denk 1 sibling, 0 replies; 8+ messages in thread From: Wolfgang Denk @ 2009-12-05 0:56 UTC (permalink / raw) To: u-boot Dear Seunghyeon Rhee, In message <4B17094D.2090300@lpmtec.com> you wrote: > > > Dear Seunghyeon Rhee, > > > > 2009/11/28 "Seunghyeon Rhee" <seunghyeon@lpmtec.com>: > > > >> The MSB of DMC1_MEM_CFG can be set to '1' for separate CKE control > >> for S3C6400. In the configuration of SMDK6400, however, two 16-bit > >> mDDR (SAMSUNG K4X51163) chips are used in parallel to form 32-bit ... > > Please rebase this patch. > > s3c6400.h is moved to include/asm-arm/arch-s3c64xx/s3c6400.h > > > > Thanks > > Minkyu Kang > > > > The MSB of DMC1_MEM_CFG can be set to '1' for separate CKE control > for S3C6400. In the configuration of SMDK6400, however, two 16-bit > mDDR (SAMSUNG K4X51163) chips are used in parallel to form 32-bit > memory bus and there is no need to control CKE for each chip > separately. AFAIK, CKE1 is not at all connected. Only CKE0 is > used. Futhermore, it should be '0' always for S3C6410. When tested > with a board which has a S3C6410 and the same memory configuration, > a side effect is observed that u-boot command "reset" doesn't work > leading to system hang. Leaving the bit clear is safe in most cases. > > Signed-off-by: Seunghyeon Rhee <seunghyeon@lpmtec.com> > --- > include/asm-arm/arch-s3c64xx/s3c6400.h | 4 ++-- > 1 files changed, 2 insertions(+), 2 deletions(-) Is this a patch re-submission or what? If yes, then please: 1) add a version to the subject (like "[PATCH v2]" 2) add a description of what has been changed below (!) the "---" line 3) and make sure thsat the commit message can be used - the one above is definitely unusable. Best regards, Wolfgang Denk -- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de I have a very small mind and must live with it. -- Edsger Dijkstra ^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2009-12-05 2:52 UTC | newest] Thread overview: 8+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2009-11-28 1:26 [U-Boot] [PATCH] samsung: fix DMC1_MEM_CFG for s3c64xx "Seunghyeon Rhee (이승현)" 2009-12-02 4:49 ` Minkyu Kang 2009-12-02 5:32 ` Seunghyeon Rhee 2009-12-03 0:41 ` [U-Boot] [PATCH (repost)] " Seunghyeon Rhee 2009-12-04 0:16 ` Minkyu Kang 2009-12-05 0:59 ` Wolfgang Denk 2009-12-05 2:52 ` Minkyu Kang 2009-12-05 0:56 ` Wolfgang Denk
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox