[U-Boot] [beagleboard] TI:OMAP: [PATCH 3/4] Support 720Mhz configuration for OMAP35xx

[Nishanth Menon <menon.nishanth@gmail.com>]

Khasim Syed Mohammed said the following on 01/09/2010 09:02 PM:
> On Sat, Jan 9, 2010 at 8:27 PM, Nishanth Menon <menon.nishanth@gmail.com> wrote:
>> Khasim Syed Mohammed said the following on 01/08/2010 09:21 PM:
>>> On Sat, Jan 9, 2010 at 1:22 AM, Nishanth Menon <menon.nishanth@gmail.com>
>>> wrote:
>>>
>>>> On Fri, Jan 8, 2010 at 9:40 AM, Khasim Syed Mohammed
>>>> <khasim@beagleboard.org> wrote:
>>>>
>>>>> From bba669562fa208d12f4c7cd8188446e8576cd6ee Mon Sep 17 00:00:00 2001
>>>>> From: Syed Mohammed Khasim <khasim@ti.com>
>>>>> Date: Fri, 8 Jan 2010 20:34:37 +0530
>>>>> Subject: [PATCH] Support 720Mhz configuration for OMAP35xx
>>>>>
[...]

>>>>> diff --git a/drivers/power/twl4030.c b/drivers/power/twl4030.c
>>>>> index eb066cb..d68e515 100644
>>>>> --- a/drivers/power/twl4030.c
>>>>> +++ b/drivers/power/twl4030.c
>>>>> @@ -59,16 +59,9 @@ void twl4030_power_reset_init(void)
>>>>>       }
>>>>>  }
>>>>>
>>>>> -
>>>>>  /*
>>>>>  * Power Init
>>>>>  */
>>>>> -#define DEV_GRP_P1             0x20
>>>>> -#define VAUX3_VSEL_28          0x03
>>>>> -#define DEV_GRP_ALL            0xE0
>>>>> -#define VPLL2_VSEL_18          0x05
>>>>> -#define VDAC_VSEL_18           0x03
>>>>> -
>>>>>  void twl4030_power_init(void)
>>>>>  {
>>>>>       unsigned char byte;
>>>>> @@ -98,8 +91,6 @@ void twl4030_power_init(void)
>>>>>                            TWL4030_PM_RECEIVER_VDAC_DEDICATED);
>>>>>  }
>>>>>
>>>>> -#define VMMC1_VSEL_30          0x02
>>>>> -
>>>>>  void twl4030_power_mmc_init(void)
>>>>>  {
>>>>>       unsigned char byte;
>>>>> @@ -113,3 +104,18 @@ void twl4030_power_mmc_init(void)
>>>>>       twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, byte,
>>>>>                            TWL4030_PM_RECEIVER_VMMC1_DEDICATED);
>>>>>  }
>>>>> +
>>>>> +/*
>>>>> + * Generic function to select Device Group and Voltage
>>>>> + */
>>>>> +void twl4030_pmrecv_vsel_cfg(u8 vsel_reg, u8 vsel_val,
>>>>> +                               u8 dev_grp, u8 dev_grp_sel)
>>>>> +{
>>>>> +       /* Select the Device Group */
>>>>> +       twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, dev_grp_sel,
>>>>> +                               dev_grp);
>>>>> +
>>>>> +       /* Select the Voltage */
>>>>> +       twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, vsel_val,
>>>>> +                               vsel_reg);
>>>>> +}
>>>>>
>>>> Assumption that i2c operations work 100% successfully! is'nt serial
>>>> bus subject to noise? and cant' i2c ops fail?
>>>>
>>> May be,  such cases will be treated as system fail. Should be handled
>>> separately for "broken platforms".
>>>
>>> In beagleboard and EVMs atleast in last 4 revs we have never
>>> encountered such problems.
>>>
>>>
>> I mean never seen an i2c read/write failure? I have seen at least a couple
>> unfortunately when one of the SDP3430's had some one solder a wrong pull up
>> resistor and another where a pull up resistor was torn off by accident.
>>
>> these are broken platforms ofcourse :).
> Yeah,
> 
>> sigh, seeing that the rest of the
>> file is messed up in this regards, I leave it for the community to further
>> comment on this.
>>
[...]

>>>>> +#define VAUX3_VSEL_28          0x03
>>>>> +#define VPLL2_VSEL_18          0x05
>>>>> +#define VDAC_VSEL_18           0x03
>>>>> +#define VMMC1_VSEL_30          0x02
>>>>> +
> Did you mean these lines ? When I apply the patch I don't see these
> kind of lines, they are properly arranged in TABs. I have also checked
> every patch with checkpatch.pl (from Linux). There are no such
> alignment issues.

no, I meant usage of twl4030_i2c_write_u8() without error check throughout the file.


Regards,
Nishanth Menon