[U-Boot] [PATCH v4 08/12] SPEAr : Support for HW mac id read/write from i2c mem

[U-Boot] [PATCH v4 08/12] SPEAr : Support for HW mac id read/write from i2c mem

[Vipin KUMAR]

This patch adds the  support to read and write mac id from i2c
memory.
For reading:
	if (env contains ethaddr)
		pick env ethaddr
	else
		pick ethaddr from i2c memory
For writing:
	chip_config ethaddr XX:XX:XX:XX:XX:XX writes the mac id
	in i2c memory

Signed-off-by: Vipin <vipin.kumar@st.com>
---
 board/spear/common/spr_misc.c |   69 ++++++++++++++++++++++++++++++++++++++++-
 1 files changed, 68 insertions(+), 1 deletions(-)

diff --git a/board/spear/common/spr_misc.c b/board/spear/common/spr_misc.c
index d70252b..9a6260f 100755
--- a/board/spear/common/spr_misc.c
+++ b/board/spear/common/spr_misc.c
@@ -62,6 +62,12 @@ int dram_init(void)
 
 int misc_init_r(void)
 {
+#if defined(CONFIG_CMD_NET)
+	uchar mac_id[6];
+
+	if (!eth_getenv_enetaddr("ethaddr", mac_id) && !i2c_read_mac(mac_id))
+		eth_setenv_enetaddr("ethaddr", mac_id);
+#endif
 	setenv("verify", "n");
 
 #if defined(CONFIG_SPEAR_USBTTY)
@@ -96,6 +102,46 @@ int spear_board_init(ulong mach_type)
 	return 0;
 }
 
+static int i2c_read_mac(uchar *buffer)
+{
+	u8 buf[2];
+
+	i2c_read(0x50, 0x0, 1, buf, 2);
+
+	/* Check if mac in i2c memory is valid */
+	if ((buf[0] == 0x55) && (buf[1] == 0xAA)) {
+		/* Valid mac address is saved in i2c eeprom */
+		i2c_read(0x50, 0x2, 1, buffer, 6);
+		return 0;
+	}
+
+	return -1;
+}
+
+static int write_mac(uchar *mac)
+{
+	unsigned char buf[2];
+
+	buf[0] = 0x55;
+	buf[1] = 0xAA;
+	i2c_write(0x50, 0x0, 1, buf, 2);
+
+	buf[0] = 0x44;
+	buf[1] = 0x66;
+
+	i2c_read(0x50, 0x0, 1, buf, 2);
+
+	/* check if valid MAC address is saved in I2C EEPROM or not? */
+	if ((buf[0] == 0x55) && (buf[1] == 0xAA)) {
+		i2c_write(0x50, 0x2, 1, mac, 6);
+		puts("I2C EEPROM written with mac address \n");
+		return 0;
+	}
+
+	puts("I2C EEPROM writing failed \n");
+	return -1;
+}
+
 #define CPU 0
 #define DDR 1
 
@@ -103,7 +149,10 @@ int do_chip_config(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 {
 	void (*sram_setfreq) (unsigned int, unsigned int);
 	struct chip_data *chip = &chip_data;
-	unsigned int frequency;
+	unsigned char mac[6];
+	unsigned int reg, frequency;
+	char *s, *e;
+	char i2c_mac[20];
 
 	if ((argc > 3) || (argc < 2)) {
 		cmd_usage(cmdtp);
@@ -134,6 +183,17 @@ int do_chip_config(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 		}
 
 		return 0;
+	} else if (!strcmp(argv[1], "ethaddr")) {
+
+		s = argv[2];
+		for (reg = 0; reg < 6; ++reg) {
+			mac[reg] = s ? simple_strtoul(s, &e, 16) : 0;
+			if (s)
+				s = (*e) ? e + 1 : e;
+		}
+		write_mac(mac);
+
+		return 0;
 	} else if (!strcmp(argv[1], "display")) {
 
 		if (chip->cpufreq == -1)
@@ -153,6 +213,13 @@ int do_chip_config(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 		else
 			printf("DDR Type    = Not Known\n");
 
+		if (!i2c_read_mac(mac)) {
+			sprintf(i2c_mac, "%pM", mac);
+			printf("Ethaddr (from i2c mem) = %s\n", i2c_mac);
+		} else {
+			printf("Ethaddr (from i2c mem) = Not set\n");
+		}
+
 		printf("Xloader Rev = %s\n", chip->version);
 
 		return 0;
-- 
1.6.0.2

[U-Boot] [PATCH v4 08/12] SPEAr : Support for HW mac id read/write from i2c mem

[Tom]

This patch adds the  support to read and write mac id from i2c
memory.
For reading:
	if (env contains ethaddr)
		pick env ethaddr
	else
		pick ethaddr from i2c memory
For writing:
	chip_config ethaddr XX:XX:XX:XX:XX:XX writes the mac id
	in i2c memory

Signed-off-by: Vipin <vipin.kumar@st.com>
---
  board/spear/common/spr_misc.c |   69 ++++++++++++++++++++++++++++++++++++++++-
  1 files changed, 68 insertions(+), 1 deletions(-)

diff --git a/board/spear/common/spr_misc.c b/board/spear/common/spr_misc.c
index d70252b..9a6260f 100755
--- a/board/spear/common/spr_misc.c
+++ b/board/spear/common/spr_misc.c
@@ -62,6 +62,12 @@ int dram_init(void)

  int misc_init_r(void)
  {
+#if defined(CONFIG_CMD_NET)
+	uchar mac_id[6];
+
+	if (!eth_getenv_enetaddr("ethaddr", mac_id) && !i2c_read_mac(mac_id))
+		eth_setenv_enetaddr("ethaddr", mac_id);
+#endif
  	setenv("verify", "n");

  #if defined(CONFIG_SPEAR_USBTTY)
@@ -96,6 +102,46 @@ int spear_board_init(ulong mach_type)
  	return 0;
  }

+static int i2c_read_mac(uchar *buffer)
+{
+	u8 buf[2];
+
+	i2c_read(0x50, 0x0, 1, buf, 2);

Change 0x50 to #define board/soc specific i2c address for MAC
Apply gobally

+
+	/* Check if mac in i2c memory is valid */
+	if ((buf[0] == 0x55) && (buf[1] == 0xAA)) {
+		/* Valid mac address is saved in i2c eeprom */
+		i2c_read(0x50, 0x2, 1, buffer, 6);
+		return 0;
+	}
+
+	return -1;
+}
+
+static int write_mac(uchar *mac)
+{
+	unsigned char buf[2];
+
+	buf[0] = 0x55;
+	buf[1] = 0xAA;
+	i2c_write(0x50, 0x0, 1, buf, 2);
+
+	buf[0] = 0x44;
+	buf[1] = 0x66;

May want to change these to #defines

Tom