[U-Boot] [PATCH] arm: kirkwood: suen3: fixed build warning

[Tom <Tom.Rix@windriver.com>]

Prafulla Wadaskar wrote:
>  
> 
>> -----Original Message-----
>> From: Tom [mailto:Tom.Rix at windriver.com] 
>> Sent: Friday, March 05, 2010 7:49 PM
>> To: Prafulla Wadaskar
>> Cc: u-boot at lists.denx.de; Ashish Karkare; Prabhanjan Sarnaik
>> Subject: Re: [U-Boot] [PATCH] arm: kirkwood: suen3: fixed 
>> build warning
>>
>> Prafulla Wadaskar wrote:
>>>  
>>>
>>>> -----Original Message-----
>>>> From: Tom [mailto:Tom.Rix at windriver.com] 
>>>> Sent: Thursday, March 04, 2010 7:25 PM
>>>> To: Prafulla Wadaskar
>>>> Cc: u-boot at lists.denx.de; Ashish Karkare; Prabhanjan Sarnaik
>>>> Subject: Re: [U-Boot] [PATCH] arm: kirkwood: suen3: fixed 
>>>> build warning
>>>>
>>>> Prafulla Wadaskar wrote:
>>>>> This patch fixes following build warning
>>>>>
>>>>> Invalid Kwbimage command Type - valid names are: BOOT_FROM, 
>>>> NAND_ECC_MODE, NAND_PAGE_SIZE, SATA_PIO_MODE, DDR_INIT_DELAY, 
>>>> DATA, , spi, nand, sata, pex, uart
>>>>> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
>>>>> ---
>>>>>  board/keymile/km_arm/kwbimage.cfg |    3 +--
>>>>>  1 files changed, 1 insertions(+), 2 deletions(-)
>>>>>
>>>>> diff --git a/board/keymile/km_arm/kwbimage.cfg 
>>>> b/board/keymile/km_arm/kwbimage.cfg
>>>>> index d6edd27..26d6aa0 100644
>>>>> --- a/board/keymile/km_arm/kwbimage.cfg
>>>>> +++ b/board/keymile/km_arm/kwbimage.cfg
>>>>> @@ -64,7 +64,6 @@ DATA 0xFFD01400 0x43000400	# SDRAM 
>>>> Configuration Register
>>>>>  # bit31-30: 01
>>>>>  
>>>>>  DATA 0xFFD01404 0x36343000	# DDR Controller Control Low
>>>>> -		0x38543000
>>>>>  # bit 3-0:  0 reserved
>>>>>  # bit 4:    0=addr/cmd in smame cycle
>>>>>  # bit 5:    0=clk is driven during self refresh, we don't 
>>>> care for APX
>>>>> @@ -170,7 +169,7 @@ DATA 0xFFD0149C 0x0000E90F	# CPU 
>>>> ODT Control
>>>>>  # bit11-10:2, DQ_ODTSel. ODT select turned on, 75 ohm
>>>>>  
>>>>>  DATA 0xFFD01480 0x00000001	# DDR Initialization Control
>>>>> -#bit0=1, enable DDR init upon this register write
>>>>> +# bit0=1, enable DDR init upon this register write
>>>>>  
>>>>>  # End of Header extension
>>>>>  DATA 0x0 0x0
>>>> This patch did not fix any of the warnings I saw.
>>>> Please recheck.
>>> Hi Tom
>>> I am sorry to say,
>>> it is not build warning but it is runtime stderr generated 
>> during kwbimage.cfg parsing.
>>> This patch removes above mentioned "Invalid Kwbimage 
>> command Type" error reported by mkimage tool during 
>> u-boot.kwb target creation for this board.
>> Ah!
>> Ok that helps.
>> I did not hold up your pull request for this.
>> Would you like this to go into ARM now?
> 
> Yes. Its better, if you can pull this too ;-) otherwise Pls flag me if I need to send pull request
> 
I have applied it to ARM
Thanks
Tom


> Regards..
> Prafulla . .
> 
>> Tom
>>
>>> Regards..
>>> Prafulla . .
>>>
>>>> Tom
>>>>