* [U-Boot] [PATCH v2] nios2: remove EP1C20, EP1S10, EP1S40 boards
2010-06-16 6:39 ` [U-Boot] [PATCH v2] nios2: remove EP1C20, EP1S10, EP1S40 boards Thomas Chou
@ 2010-07-12 15:59 ` Scott McNutt
0 siblings, 0 replies; 2+ messages in thread
From: Scott McNutt @ 2010-07-12 15:59 UTC (permalink / raw)
To: u-boot
Applied to:
git://git.denx.de/u-boot-nios.git next
Thanks,
--Scott
Thomas Chou wrote:
> The example configuration files of nios2-generic board can generated
> binary to run on the EP1C20, EP1S10, and EP1S40 boards. So the three
> boards can be removed.
>
> With nios2-generic approach, the fpga parameter header file can
> be generated from hardware designs using tools. Porting u-boot for
> nios2 boards is simplified. Vendors can supply their fpga parameter
> file or patches to add a new nios2-generic board instance. There is
> no need to include other boards support for nios2 in the u-boot
> mainline.
>
> Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
> ---
> Hi Scott, please rebase your next branch to Wolfgang's next, 06/14.
>
> v2: rebased to Makefile simplify
>
> MAINTAINERS | 3 -
> MAKEALL | 3 -
> board/altera/ep1c20/Makefile | 55 -----------
> board/altera/ep1c20/config.mk | 31 ------
> board/altera/ep1c20/ep1c20.c | 52 ----------
> board/altera/ep1s10/Makefile | 55 -----------
> board/altera/ep1s10/config.mk | 31 ------
> board/altera/ep1s10/ep1s10.c | 52 ----------
> board/altera/ep1s40/Makefile | 55 -----------
> board/altera/ep1s40/config.mk | 31 ------
> board/altera/ep1s40/ep1s40.c | 47 ---------
> boards.cfg | 3 -
> include/configs/EP1C20.h | 214 -----------------------------------------
> include/configs/EP1S10.h | 207 ---------------------------------------
> include/configs/EP1S40.h | 207 ---------------------------------------
> 15 files changed, 0 insertions(+), 1046 deletions(-)
> delete mode 100644 board/altera/ep1c20/Makefile
> delete mode 100644 board/altera/ep1c20/config.mk
> delete mode 100644 board/altera/ep1c20/ep1c20.c
> delete mode 100644 board/altera/ep1s10/Makefile
> delete mode 100644 board/altera/ep1s10/config.mk
> delete mode 100644 board/altera/ep1s10/ep1s10.c
> delete mode 100644 board/altera/ep1s40/Makefile
> delete mode 100644 board/altera/ep1s40/config.mk
> delete mode 100644 board/altera/ep1s40/ep1s40.c
> delete mode 100644 include/configs/EP1C20.h
> delete mode 100644 include/configs/EP1S10.h
> delete mode 100644 include/configs/EP1S40.h
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 7a13d28..700dd8c 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -852,9 +852,6 @@ Scott McNutt <smcnutt@psyent.com>
>
> PCI5441 Nios-II
> PK1C20 Nios-II
> - EP1C20 Nios-II
> - EP1S10 Nios-II
> - EP1S40 Nios-II
> nios2-generic Nios-II
>
> #########################################################################
> diff --git a/MAKEALL b/MAKEALL
> index 2527352..56db729 100755
> --- a/MAKEALL
> +++ b/MAKEALL
> @@ -815,9 +815,6 @@ LIST_x86=" \
> #########################################################################
>
> LIST_nios2=" \
> - EP1C20 \
> - EP1S10 \
> - EP1S40 \
> PCI5441 \
> PK1C20 \
> nios2-generic \
> diff --git a/board/altera/ep1c20/Makefile b/board/altera/ep1c20/Makefile
> deleted file mode 100644
> index acad2aa..0000000
> --- a/board/altera/ep1c20/Makefile
> +++ /dev/null
> @@ -1,55 +0,0 @@
> -#
> -# (C) Copyright 2001-2006
> -# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
> -#
> -# See file CREDITS for list of people who contributed to this
> -# project.
> -#
> -# This program is free software; you can redistribute it and/or
> -# modify it under the terms of the GNU General Public License as
> -# published by the Free Software Foundation; either version 2 of
> -# the License, or (at your option) any later version.
> -#
> -# This program is distributed in the hope that it will be useful,
> -# but WITHOUT ANY WARRANTY; without even the implied warranty of
> -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> -# GNU General Public License for more details.
> -#
> -# You should have received a copy of the GNU General Public License
> -# along with this program; if not, write to the Free Software
> -# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> -# MA 02111-1307 USA
> -#
> -
> -include $(TOPDIR)/config.mk
> -ifneq ($(OBJTREE),$(SRCTREE))
> -$(shell mkdir -p $(obj)../common)
> -endif
> -
> -LIB = $(obj)lib$(BOARD).a
> -
> -COMOBJS := ../common/AMDLV065D.o ../common/epled.o
> -
> -COBJS := $(BOARD).o $(COMOBJS)
> -
> -SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
> -OBJS := $(addprefix $(obj),$(COBJS))
> -SOBJS := $(addprefix $(obj),$(SOBJS))
> -
> -$(LIB): $(obj).depend $(OBJS)
> - $(AR) $(ARFLAGS) $@ $(OBJS)
> -
> -clean:
> - rm -f $(SOBJS) $(OBJS)
> -
> -distclean: clean
> - rm -f $(LIB) core *.bak $(obj).depend
> -
> -#########################################################################
> -
> -# defines $(obj).depend target
> -include $(SRCTREE)/rules.mk
> -
> -sinclude $(obj).depend
> -
> -#########################################################################
> diff --git a/board/altera/ep1c20/config.mk b/board/altera/ep1c20/config.mk
> deleted file mode 100644
> index dab2740..0000000
> --- a/board/altera/ep1c20/config.mk
> +++ /dev/null
> @@ -1,31 +0,0 @@
> -#
> -# (C) Copyright 2005, Psyent Corporation <www.psyent.com>
> -# Scott McNutt <smcnutt@psyent.com>
> -#
> -# See file CREDITS for list of people who contributed to this
> -# project.
> -#
> -# This program is free software; you can redistribute it and/or
> -# modify it under the terms of the GNU General Public License as
> -# published by the Free Software Foundation; either version 2 of
> -# the License, or (at your option) any later version.
> -#
> -# This program is distributed in the hope that it will be useful,
> -# but WITHOUT ANY WARRANTY; without even the implied warranty of
> -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> -# GNU General Public License for more details.
> -#
> -# You should have received a copy of the GNU General Public License
> -# along with this program; if not, write to the Free Software
> -# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> -# MA 02111-1307 USA
> -#
> -
> -TEXT_BASE = 0x01fc0000
> -
> -PLATFORM_CPPFLAGS += -mno-hw-div -mno-hw-mul
> -PLATFORM_CPPFLAGS += -I$(TOPDIR)/board/$(VENDOR)/include
> -
> -ifeq ($(debug),1)
> -PLATFORM_CPPFLAGS += -DDEBUG
> -endif
> diff --git a/board/altera/ep1c20/ep1c20.c b/board/altera/ep1c20/ep1c20.c
> deleted file mode 100644
> index 82900f7..0000000
> --- a/board/altera/ep1c20/ep1c20.c
> +++ /dev/null
> @@ -1,52 +0,0 @@
> -/*
> - * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
> - * Scott McNutt <smcnutt@psyent.com>
> - *
> - * See file CREDITS for list of people who contributed to this
> - * project.
> - *
> - * This program is free software; you can redistribute it and/or
> - * modify it under the terms of the GNU General Public License as
> - * published by the Free Software Foundation; either version 2 of
> - * the License, or (at your option) any later version.
> - *
> - * This program is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> - * GNU General Public License for more details.
> - *
> - * You should have received a copy of the GNU General Public License
> - * along with this program; if not, write to the Free Software
> - * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> - * MA 02111-1307 USA
> - */
> -
> -#include <common.h>
> -#include <netdev.h>
> -
> -int board_early_init_f (void)
> -{
> - return 0;
> -}
> -
> -int checkboard (void)
> -{
> - puts ("BOARD : Altera EP-1C20\n");
> - return 0;
> -}
> -
> -phys_size_t initdram (int board_type)
> -{
> - return (0);
> -}
> -
> -#ifdef CONFIG_CMD_NET
> -int board_eth_init(bd_t *bis)
> -{
> - int rc = 0;
> -#ifdef CONFIG_SMC91111
> - rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
> -#endif
> - return rc;
> -}
> -#endif
> diff --git a/board/altera/ep1s10/Makefile b/board/altera/ep1s10/Makefile
> deleted file mode 100644
> index acad2aa..0000000
> --- a/board/altera/ep1s10/Makefile
> +++ /dev/null
> @@ -1,55 +0,0 @@
> -#
> -# (C) Copyright 2001-2006
> -# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
> -#
> -# See file CREDITS for list of people who contributed to this
> -# project.
> -#
> -# This program is free software; you can redistribute it and/or
> -# modify it under the terms of the GNU General Public License as
> -# published by the Free Software Foundation; either version 2 of
> -# the License, or (at your option) any later version.
> -#
> -# This program is distributed in the hope that it will be useful,
> -# but WITHOUT ANY WARRANTY; without even the implied warranty of
> -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> -# GNU General Public License for more details.
> -#
> -# You should have received a copy of the GNU General Public License
> -# along with this program; if not, write to the Free Software
> -# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> -# MA 02111-1307 USA
> -#
> -
> -include $(TOPDIR)/config.mk
> -ifneq ($(OBJTREE),$(SRCTREE))
> -$(shell mkdir -p $(obj)../common)
> -endif
> -
> -LIB = $(obj)lib$(BOARD).a
> -
> -COMOBJS := ../common/AMDLV065D.o ../common/epled.o
> -
> -COBJS := $(BOARD).o $(COMOBJS)
> -
> -SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
> -OBJS := $(addprefix $(obj),$(COBJS))
> -SOBJS := $(addprefix $(obj),$(SOBJS))
> -
> -$(LIB): $(obj).depend $(OBJS)
> - $(AR) $(ARFLAGS) $@ $(OBJS)
> -
> -clean:
> - rm -f $(SOBJS) $(OBJS)
> -
> -distclean: clean
> - rm -f $(LIB) core *.bak $(obj).depend
> -
> -#########################################################################
> -
> -# defines $(obj).depend target
> -include $(SRCTREE)/rules.mk
> -
> -sinclude $(obj).depend
> -
> -#########################################################################
> diff --git a/board/altera/ep1s10/config.mk b/board/altera/ep1s10/config.mk
> deleted file mode 100644
> index dab2740..0000000
> --- a/board/altera/ep1s10/config.mk
> +++ /dev/null
> @@ -1,31 +0,0 @@
> -#
> -# (C) Copyright 2005, Psyent Corporation <www.psyent.com>
> -# Scott McNutt <smcnutt@psyent.com>
> -#
> -# See file CREDITS for list of people who contributed to this
> -# project.
> -#
> -# This program is free software; you can redistribute it and/or
> -# modify it under the terms of the GNU General Public License as
> -# published by the Free Software Foundation; either version 2 of
> -# the License, or (at your option) any later version.
> -#
> -# This program is distributed in the hope that it will be useful,
> -# but WITHOUT ANY WARRANTY; without even the implied warranty of
> -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> -# GNU General Public License for more details.
> -#
> -# You should have received a copy of the GNU General Public License
> -# along with this program; if not, write to the Free Software
> -# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> -# MA 02111-1307 USA
> -#
> -
> -TEXT_BASE = 0x01fc0000
> -
> -PLATFORM_CPPFLAGS += -mno-hw-div -mno-hw-mul
> -PLATFORM_CPPFLAGS += -I$(TOPDIR)/board/$(VENDOR)/include
> -
> -ifeq ($(debug),1)
> -PLATFORM_CPPFLAGS += -DDEBUG
> -endif
> diff --git a/board/altera/ep1s10/ep1s10.c b/board/altera/ep1s10/ep1s10.c
> deleted file mode 100644
> index cf886da..0000000
> --- a/board/altera/ep1s10/ep1s10.c
> +++ /dev/null
> @@ -1,52 +0,0 @@
> -/*
> - * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
> - * Scott McNutt <smcnutt@psyent.com>
> - *
> - * See file CREDITS for list of people who contributed to this
> - * project.
> - *
> - * This program is free software; you can redistribute it and/or
> - * modify it under the terms of the GNU General Public License as
> - * published by the Free Software Foundation; either version 2 of
> - * the License, or (at your option) any later version.
> - *
> - * This program is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> - * GNU General Public License for more details.
> - *
> - * You should have received a copy of the GNU General Public License
> - * along with this program; if not, write to the Free Software
> - * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> - * MA 02111-1307 USA
> - */
> -
> -#include <common.h>
> -#include <netdev.h>
> -
> -int board_early_init_f (void)
> -{
> - return 0;
> -}
> -
> -int checkboard (void)
> -{
> - puts ("BOARD : Altera EP-1S10\n");
> - return 0;
> -}
> -
> -phys_size_t initdram (int board_type)
> -{
> - return (0);
> -}
> -
> -#ifdef CONFIG_CMD_NET
> -int board_eth_init(bd_t *bis)
> -{
> - int rc = 0;
> -#ifdef CONFIG_SMC91111
> - rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
> -#endif
> - return rc;
> -}
> -#endif
> diff --git a/board/altera/ep1s40/Makefile b/board/altera/ep1s40/Makefile
> deleted file mode 100644
> index acad2aa..0000000
> --- a/board/altera/ep1s40/Makefile
> +++ /dev/null
> @@ -1,55 +0,0 @@
> -#
> -# (C) Copyright 2001-2006
> -# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
> -#
> -# See file CREDITS for list of people who contributed to this
> -# project.
> -#
> -# This program is free software; you can redistribute it and/or
> -# modify it under the terms of the GNU General Public License as
> -# published by the Free Software Foundation; either version 2 of
> -# the License, or (at your option) any later version.
> -#
> -# This program is distributed in the hope that it will be useful,
> -# but WITHOUT ANY WARRANTY; without even the implied warranty of
> -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> -# GNU General Public License for more details.
> -#
> -# You should have received a copy of the GNU General Public License
> -# along with this program; if not, write to the Free Software
> -# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> -# MA 02111-1307 USA
> -#
> -
> -include $(TOPDIR)/config.mk
> -ifneq ($(OBJTREE),$(SRCTREE))
> -$(shell mkdir -p $(obj)../common)
> -endif
> -
> -LIB = $(obj)lib$(BOARD).a
> -
> -COMOBJS := ../common/AMDLV065D.o ../common/epled.o
> -
> -COBJS := $(BOARD).o $(COMOBJS)
> -
> -SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
> -OBJS := $(addprefix $(obj),$(COBJS))
> -SOBJS := $(addprefix $(obj),$(SOBJS))
> -
> -$(LIB): $(obj).depend $(OBJS)
> - $(AR) $(ARFLAGS) $@ $(OBJS)
> -
> -clean:
> - rm -f $(SOBJS) $(OBJS)
> -
> -distclean: clean
> - rm -f $(LIB) core *.bak $(obj).depend
> -
> -#########################################################################
> -
> -# defines $(obj).depend target
> -include $(SRCTREE)/rules.mk
> -
> -sinclude $(obj).depend
> -
> -#########################################################################
> diff --git a/board/altera/ep1s40/config.mk b/board/altera/ep1s40/config.mk
> deleted file mode 100644
> index dab2740..0000000
> --- a/board/altera/ep1s40/config.mk
> +++ /dev/null
> @@ -1,31 +0,0 @@
> -#
> -# (C) Copyright 2005, Psyent Corporation <www.psyent.com>
> -# Scott McNutt <smcnutt@psyent.com>
> -#
> -# See file CREDITS for list of people who contributed to this
> -# project.
> -#
> -# This program is free software; you can redistribute it and/or
> -# modify it under the terms of the GNU General Public License as
> -# published by the Free Software Foundation; either version 2 of
> -# the License, or (at your option) any later version.
> -#
> -# This program is distributed in the hope that it will be useful,
> -# but WITHOUT ANY WARRANTY; without even the implied warranty of
> -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> -# GNU General Public License for more details.
> -#
> -# You should have received a copy of the GNU General Public License
> -# along with this program; if not, write to the Free Software
> -# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> -# MA 02111-1307 USA
> -#
> -
> -TEXT_BASE = 0x01fc0000
> -
> -PLATFORM_CPPFLAGS += -mno-hw-div -mno-hw-mul
> -PLATFORM_CPPFLAGS += -I$(TOPDIR)/board/$(VENDOR)/include
> -
> -ifeq ($(debug),1)
> -PLATFORM_CPPFLAGS += -DDEBUG
> -endif
> diff --git a/board/altera/ep1s40/ep1s40.c b/board/altera/ep1s40/ep1s40.c
> deleted file mode 100644
> index 6395de7..0000000
> --- a/board/altera/ep1s40/ep1s40.c
> +++ /dev/null
> @@ -1,47 +0,0 @@
> -/*
> - * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
> - * Scott McNutt <smcnutt@psyent.com>
> - *
> - * See file CREDITS for list of people who contributed to this
> - * project.
> - *
> - * This program is free software; you can redistribute it and/or
> - * modify it under the terms of the GNU General Public License as
> - * published by the Free Software Foundation; either version 2 of
> - * the License, or (at your option) any later version.
> - *
> - * This program is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> - * GNU General Public License for more details.
> - *
> - * You should have received a copy of the GNU General Public License
> - * along with this program; if not, write to the Free Software
> - * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> - * MA 02111-1307 USA
> - */
> -
> -#include <common.h>
> -#include <netdev.h>
> -
> -int checkboard (void)
> -{
> - puts ("BOARD : Altera EP-1S40\n");
> - return 0;
> -}
> -
> -phys_size_t initdram (int board_type)
> -{
> - return (0);
> -}
> -
> -#ifdef CONFIG_CMD_NET
> -int board_eth_init(bd_t *bis)
> -{
> - int rc = 0;
> -#ifdef CONFIG_SMC91111
> - rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
> -#endif
> - return rc;
> -}
> -#endif
> diff --git a/boards.cfg b/boards.cfg
> index e54673e..9b126a3 100644
> --- a/boards.cfg
> +++ b/boards.cfg
> @@ -75,9 +75,6 @@ M5272C3 m68k mcf52x2 m5272c3 freescale
> EP2500 m68k mcf52x2 ep2500 Mercury
> purple mips mips
> tb0229 mips mips
> -EP1C20 nios2 nios2 ep1c20 altera
> -EP1S10 nios2 nios2 ep1s10 altera
> -EP1S40 nios2 nios2 ep1s40 altera
> PCI5441 nios2 nios2 pci5441 psyent
> PK1C20 nios2 nios2 pk1c20 psyent
> P3G4 powerpc 74xx_7xx evb64260
> diff --git a/include/configs/EP1C20.h b/include/configs/EP1C20.h
> deleted file mode 100644
> index 3920d35..0000000
> --- a/include/configs/EP1C20.h
> +++ /dev/null
> @@ -1,214 +0,0 @@
> -/*
> - * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
> - * Scott McNutt <smcnutt@psyent.com>
> - *
> - * See file CREDITS for list of people who contributed to this
> - * project.
> - *
> - * This program is free software; you can redistribute it and/or
> - * modify it under the terms of the GNU General Public License as
> - * published by the Free Software Foundation; either version 2 of
> - * the License, or (at your option) any later version.
> - *
> - * This program is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> - * GNU General Public License for more details.
> - *
> - * You should have received a copy of the GNU General Public License
> - * along with this program; if not, write to the Free Software
> - * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> - * MA 02111-1307 USA
> - */
> -
> -#ifndef __CONFIG_H
> -#define __CONFIG_H
> -
> -/*------------------------------------------------------------------------
> - * BOARD/CPU
> - *----------------------------------------------------------------------*/
> -#define CONFIG_EP1C20 1 /* EP1C20 board */
> -#define CONFIG_SYS_CLK_FREQ 50000000 /* 50 MHz core clk */
> -
> -#define CONFIG_SYS_RESET_ADDR 0x00000000 /* Hard-reset address */
> -#define CONFIG_SYS_EXCEPTION_ADDR 0x01000020 /* Exception entry point*/
> -#define CONFIG_SYS_NIOS_SYSID_BASE 0x021208b8 /* System id address */
> -#define CONFIG_BOARD_EARLY_INIT_F 1 /* enable early board-spec. init*/
> -
> -/*------------------------------------------------------------------------
> - * CACHE -- the following will support II/s and II/f. The II/s does not
> - * have dcache, so the cache instructions will behave as NOPs.
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_ICACHE_SIZE 4096 /* 4 KByte total */
> -#define CONFIG_SYS_ICACHELINE_SIZE 32 /* 32 bytes/line */
> -#define CONFIG_SYS_DCACHE_SIZE 2048 /* 2 KByte (II/f) */
> -#define CONFIG_SYS_DCACHELINE_SIZE 4 /* 4 bytes/line (II/f) */
> -
> -/*------------------------------------------------------------------------
> - * MEMORY BASE ADDRESSES
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_FLASH_BASE 0x00000000 /* FLASH base addr */
> -#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */
> -#define CONFIG_SYS_SDRAM_BASE 0x01000000 /* SDRAM base addr */
> -#define CONFIG_SYS_SDRAM_SIZE 0x01000000 /* 16 MByte */
> -#define CONFIG_SYS_SRAM_BASE 0x02000000 /* SRAM base addr */
> -#define CONFIG_SYS_SRAM_SIZE 0x00100000 /* 1 MB (only 1M mapped)*/
> -
> -/*------------------------------------------------------------------------
> - * MEMORY ORGANIZATION
> - * -Monitor at top.
> - * -The heap is placed below the monitor.
> - * -Global data is placed below the heap.
> - * -The stack is placed below global data (&grows down).
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 128k */
> -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Global data size rsvd*/
> -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
> -
> -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
> -#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
> -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
> -#define CONFIG_SYS_INIT_SP CONFIG_SYS_GBL_DATA_OFFSET
> -
> -/*------------------------------------------------------------------------
> - * FLASH (AM29LV065D)
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* Max # sects per bank */
> -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max # of flash banks */
> -#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Erase timeout (msec) */
> -#define CONFIG_SYS_FLASH_WRITE_TOUT 100 /* Write timeout (msec) */
> -#define CONFIG_SYS_FLASH_WORD_SIZE unsigned char /* flash word size */
> -
> -/*------------------------------------------------------------------------
> - * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above
> - * CONFIG_SYS_RESET_ADDR, since we assume the monitor is stored at the
> - * reset address, no? This will keep the environment in user region
> - * of flash. NOTE: the monitor length must be multiple of sector size
> - * (which is common practice).
> - *----------------------------------------------------------------------*/
> -#define CONFIG_ENV_IS_IN_FLASH 1 /* Environment in flash */
> -#define CONFIG_ENV_SIZE (64 * 1024) /* 64 KByte (1 sector) */
> -#define CONFIG_ENV_OVERWRITE /* Serial change Ok */
> -#define CONFIG_ENV_ADDR (CONFIG_SYS_RESET_ADDR + CONFIG_SYS_MONITOR_LEN)
> -
> -/*------------------------------------------------------------------------
> - * CONSOLE
> - *----------------------------------------------------------------------*/
> -#define CONFIG_ALTERA_UART 1 /* Use altera uart */
> -#if defined(CONFIG_ALTERA_JTAG_UART)
> -#define CONFIG_SYS_NIOS_CONSOLE 0x021208b0 /* JTAG UART base addr */
> -#else
> -#define CONFIG_SYS_NIOS_CONSOLE 0x02120840 /* UART base addr */
> -#endif
> -
> -#define CONFIG_SYS_NIOS_FIXEDBAUD 1 /* Baudrate is fixed */
> -#define CONFIG_BAUDRATE 115200 /* Initial baudrate */
> -#define CONFIG_SYS_BAUDRATE_TABLE {115200} /* It's fixed ;-) */
> -
> -#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* Suppress console info*/
> -
> -/*------------------------------------------------------------------------
> - * EPCS Device -- wne CONFIG_SYS_NIOS_EPCSBASE is defined code/commands for
> - * epcs device access is enabled. The base address is the epcs
> - * _register_ base address, NOT THE ADDRESS OF THE MEMORY BLOCK.
> - * The register base is currently at offset 0x600 from the memory base.
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_NIOS_EPCSBASE 0x02100200 /* EPCS register base */
> -
> -/*------------------------------------------------------------------------
> - * DEBUG
> - *----------------------------------------------------------------------*/
> -#undef CONFIG_ROM_STUBS /* Stubs not in ROM */
> -
> -/*------------------------------------------------------------------------
> - * TIMEBASE --
> - *
> - * The high res timer defaults to 1 msec. Since it includes the period
> - * registers, the interrupt frequency can be reduced using TMRCNT.
> - * If the default period is acceptable, TMRCNT can be left undefined.
> - * TMRMS represents the desired mecs per tick (msecs per interrupt).
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_HZ 1000 /* Always 1000 */
> -#define CONFIG_SYS_NIOS_TMRBASE 0x02120820 /* Tick timer base addr */
> -#define CONFIG_SYS_NIOS_TMRIRQ 3 /* Timer IRQ num */
> -#define CONFIG_SYS_NIOS_TMRMS 10 /* Desired period (msec)*/
> -#define CONFIG_SYS_NIOS_TMRCNT \
> - (CONFIG_SYS_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000))
> -
> -/*------------------------------------------------------------------------
> - * STATUS LED -- Provides a simple blinking led. For Nios2 each board
> - * must implement its own led routines -- leds are, after all,
> - * board-specific, no?
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_LEDPIO_ADDR 0x02120870 /* LED PIO base addr */
> -#define CONFIG_STATUS_LED /* Enable status driver */
> -
> -#define STATUS_LED_BIT 1 /* Bit-0 on PIO */
> -#define STATUS_LED_STATE 1 /* Blinking */
> -#define STATUS_LED_PERIOD (500/CONFIG_SYS_NIOS_TMRMS) /* Every 500 msec */
> -
> -/*------------------------------------------------------------------------
> - * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ...
> - * and really doesn't need any additional clutter. So I choose the lazy
> - * way out to avoid changes there -- define the base address to ensure
> - * cache bypass so there's no need to monkey with inx/outx macros.
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SMC91111_BASE 0x82110300 /* Base addr (bypass) */
> -#define CONFIG_NET_MULTI
> -#define CONFIG_SMC91111 /* Using SMC91c111 */
> -#undef CONFIG_SMC91111_EXT_PHY /* Internal PHY */
> -#define CONFIG_SMC_USE_32_BIT /* 32-bit interface */
> -
> -#define CONFIG_ETHADDR 08:00:3e:26:0a:5b
> -#define CONFIG_NETMASK 255.255.255.0
> -#define CONFIG_IPADDR 192.168.2.21
> -#define CONFIG_SERVERIP 192.168.2.16
> -
> -
> -/*
> - * BOOTP options
> - */
> -#define CONFIG_BOOTP_BOOTFILESIZE
> -#define CONFIG_BOOTP_BOOTPATH
> -#define CONFIG_BOOTP_GATEWAY
> -#define CONFIG_BOOTP_HOSTNAME
> -
> -
> -/*
> - * Command line configuration.
> - */
> -#include <config_cmd_default.h>
> -
> -#define CONFIG_CMD_DHCP
> -#define CONFIG_CMD_IRQ
> -#define CONFIG_CMD_PING
> -#define CONFIG_CMD_SAVES
> -
> -#undef CONFIG_CMD_BOOTD
> -#undef CONFIG_CMD_CONSOLE
> -#undef CONFIG_CMD_FPGA
> -#undef CONFIG_CMD_IMLS
> -#undef CONFIG_CMD_ITEST
> -#undef CONFIG_CMD_NFS
> -#undef CONFIG_CMD_SETGETDCR
> -#undef CONFIG_CMD_SOURCE
> -#undef CONFIG_CMD_XIMG
> -
> -
> -/*------------------------------------------------------------------------
> - * MISC
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_LONGHELP /* Provide extended help*/
> -#define CONFIG_SYS_PROMPT "==> " /* Command prompt */
> -#define CONFIG_SYS_CBSIZE 256 /* Console I/O buf size */
> -#define CONFIG_SYS_MAXARGS 16 /* Max command args */
> -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot arg buf size */
> -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buf size */
> -#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE /* Default load address */
> -#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE /* Start addr for test */
> -#define CONFIG_SYS_MEMTEST_END CONFIG_SYS_INIT_SP - 0x00020000
> -
> -#define CONFIG_SYS_HUSH_PARSER
> -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
> -
> -#endif /* __CONFIG_H */
> diff --git a/include/configs/EP1S10.h b/include/configs/EP1S10.h
> deleted file mode 100644
> index bfbf8c1..0000000
> --- a/include/configs/EP1S10.h
> +++ /dev/null
> @@ -1,207 +0,0 @@
> -/*
> - * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
> - * Scott McNutt <smcnutt@psyent.com>
> - *
> - * See file CREDITS for list of people who contributed to this
> - * project.
> - *
> - * This program is free software; you can redistribute it and/or
> - * modify it under the terms of the GNU General Public License as
> - * published by the Free Software Foundation; either version 2 of
> - * the License, or (at your option) any later version.
> - *
> - * This program is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> - * GNU General Public License for more details.
> - *
> - * You should have received a copy of the GNU General Public License
> - * along with this program; if not, write to the Free Software
> - * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> - * MA 02111-1307 USA
> - */
> -
> -#ifndef __CONFIG_H
> -#define __CONFIG_H
> -
> -/*------------------------------------------------------------------------
> - * BOARD/CPU
> - *----------------------------------------------------------------------*/
> -#define CONFIG_EP1S10 1 /* EP1S10 board */
> -#define CONFIG_SYS_CLK_FREQ 50000000 /* 50 MHz core clk */
> -
> -#define CONFIG_SYS_RESET_ADDR 0x00000000 /* Hard-reset address */
> -#define CONFIG_SYS_EXCEPTION_ADDR 0x01000020 /* Exception entry point*/
> -#define CONFIG_SYS_NIOS_SYSID_BASE 0x021208b8 /* System id address */
> -
> -/*------------------------------------------------------------------------
> - * CACHE -- the following will support II/s and II/f. The II/s does not
> - * have dcache, so the cache instructions will behave as NOPs.
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_ICACHE_SIZE 4096 /* 4 KByte total */
> -#define CONFIG_SYS_ICACHELINE_SIZE 32 /* 32 bytes/line */
> -#define CONFIG_SYS_DCACHE_SIZE 2048 /* 2 KByte (II/f) */
> -#define CONFIG_SYS_DCACHELINE_SIZE 4 /* 4 bytes/line (II/f) */
> -
> -/*------------------------------------------------------------------------
> - * MEMORY BASE ADDRESSES
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_FLASH_BASE 0x00000000 /* FLASH base addr */
> -#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */
> -#define CONFIG_SYS_SDRAM_BASE 0x01000000 /* SDRAM base addr */
> -#define CONFIG_SYS_SDRAM_SIZE 0x01000000 /* 16 MByte */
> -#define CONFIG_SYS_SRAM_BASE 0x02000000 /* SRAM base addr */
> -#define CONFIG_SYS_SRAM_SIZE 0x00100000 /* 1 MB */
> -
> -/*------------------------------------------------------------------------
> - * MEMORY ORGANIZATION
> - * -Monitor at top.
> - * -The heap is placed below the monitor.
> - * -Global data is placed below the heap.
> - * -The stack is placed below global data (&grows down).
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256k */
> -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Global data size rsvd*/
> -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 256*1024) /* 256k heap */
> -
> -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
> -#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
> -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
> -#define CONFIG_SYS_INIT_SP CONFIG_SYS_GBL_DATA_OFFSET
> -
> -/*------------------------------------------------------------------------
> - * FLASH (AM29LV065D)
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* Max # sects per bank */
> -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max # of flash banks */
> -#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Erase timeout (msec) */
> -#define CONFIG_SYS_FLASH_WRITE_TOUT 100 /* Write timeout (msec) */
> -
> -/*------------------------------------------------------------------------
> - * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above
> - * CONFIG_SYS_FLASH_BASE, since we assume that u-boot is stored at the bottom
> - * of flash memory. This will keep the environment in user region
> - * of flash. NOTE: the monitor length must be multiple of sector size
> - * (which is common practice).
> - *----------------------------------------------------------------------*/
> -#define CONFIG_ENV_IS_IN_FLASH 1 /* Environment in flash */
> -#define CONFIG_ENV_SIZE (64 * 1024) /* 64 KByte (1 sector) */
> -#define CONFIG_ENV_OVERWRITE /* Serial change Ok */
> -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
> -
> -/*------------------------------------------------------------------------
> - * CONSOLE
> - *----------------------------------------------------------------------*/
> -#define CONFIG_ALTERA_UART 1 /* Use altera uart */
> -#if defined(CONFIG_ALTERA_JTAG_UART)
> -#define CONFIG_SYS_NIOS_CONSOLE 0x021208b0 /* JTAG UART base addr */
> -#else
> -#define CONFIG_SYS_NIOS_CONSOLE 0x02120840 /* UART base addr */
> -#endif
> -
> -#define CONFIG_SYS_NIOS_FIXEDBAUD 1 /* Baudrate is fixed */
> -#define CONFIG_BAUDRATE 115200 /* Initial baudrate */
> -#define CONFIG_SYS_BAUDRATE_TABLE {115200} /* It's fixed ;-) */
> -
> -#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* Suppress console info*/
> -
> -/*------------------------------------------------------------------------
> - * EPCS Device -- None for stratix.
> - *----------------------------------------------------------------------*/
> -#undef CONFIG_SYS_NIOS_EPCSBASE
> -
> -/*------------------------------------------------------------------------
> - * DEBUG
> - *----------------------------------------------------------------------*/
> -#undef CONFIG_ROM_STUBS /* Stubs not in ROM */
> -
> -/*------------------------------------------------------------------------
> - * TIMEBASE --
> - *
> - * The high res timer defaults to 1 msec. Since it includes the period
> - * registers, the interrupt frequency can be reduced using TMRCNT.
> - * If the default period is acceptable, TMRCNT can be left undefined.
> - * TMRMS represents the desired mecs per tick (msecs per interrupt).
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_HZ 1000 /* Always 1000 */
> -#define CONFIG_SYS_NIOS_TMRBASE 0x02120820 /* Tick timer base addr */
> -#define CONFIG_SYS_NIOS_TMRIRQ 3 /* Timer IRQ num */
> -#define CONFIG_SYS_NIOS_TMRMS 10 /* Desired period (msec)*/
> -#define CONFIG_SYS_NIOS_TMRCNT \
> - (CONFIG_SYS_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000))
> -
> -/*------------------------------------------------------------------------
> - * STATUS LED -- Provides a simple blinking led. For Nios2 each board
> - * must implement its own led routines -- since leds are board-specific.
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_LEDPIO_ADDR 0x02120870 /* LED PIO base addr */
> -#define CONFIG_STATUS_LED /* Enable status driver */
> -
> -#define STATUS_LED_BIT 1 /* Bit-0 on PIO */
> -#define STATUS_LED_STATE 1 /* Blinking */
> -#define STATUS_LED_PERIOD (500/CONFIG_SYS_NIOS_TMRMS) /* Every 500 msec */
> -
> -/*------------------------------------------------------------------------
> - * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ...
> - * and really doesn't need any additional clutter. So I choose the lazy
> - * way out to avoid changes there -- define the base address to ensure
> - * cache bypass so there's no need to monkey with inx/outx macros.
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SMC91111_BASE 0x82110300 /* Base addr (bypass) */
> -#define CONFIG_NET_MULTI
> -#define CONFIG_SMC91111 /* Using SMC91c111 */
> -#undef CONFIG_SMC91111_EXT_PHY /* Internal PHY */
> -#define CONFIG_SMC_USE_32_BIT /* 32-bit interface */
> -
> -#define CONFIG_ETHADDR 08:00:3e:26:0a:5b
> -#define CONFIG_NETMASK 255.255.255.0
> -#define CONFIG_IPADDR 192.168.2.21
> -#define CONFIG_SERVERIP 192.168.2.16
> -
> -
> -/*
> - * BOOTP options
> - */
> -#define CONFIG_BOOTP_BOOTFILESIZE
> -#define CONFIG_BOOTP_BOOTPATH
> -#define CONFIG_BOOTP_GATEWAY
> -#define CONFIG_BOOTP_HOSTNAME
> -
> -
> -/*
> - * Command line configuration.
> - */
> -#define CONFIG_CMD_BDI
> -#define CONFIG_CMD_DHCP
> -#define CONFIG_CMD_ECHO
> -#define CONFIG_CMD_SAVEENV
> -#define CONFIG_CMD_FLASH
> -#define CONFIG_CMD_IMI
> -#define CONFIG_CMD_IRQ
> -#define CONFIG_CMD_LOADS
> -#define CONFIG_CMD_LOADB
> -#define CONFIG_CMD_MEMORY
> -#define CONFIG_CMD_MISC
> -#define CONFIG_CMD_NET
> -#define CONFIG_CMD_PING
> -#define CONFIG_CMD_RUN
> -#define CONFIG_CMD_SAVES
> -
> -
> -/*------------------------------------------------------------------------
> - * MISC
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_LONGHELP /* Provide extended help*/
> -#define CONFIG_SYS_PROMPT "==> " /* Command prompt */
> -#define CONFIG_SYS_CBSIZE 256 /* Console I/O buf size */
> -#define CONFIG_SYS_MAXARGS 16 /* Max command args */
> -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot arg buf size */
> -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buf size */
> -#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE /* Default load address */
> -#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE /* Start addr for test */
> -#define CONFIG_SYS_MEMTEST_END CONFIG_SYS_INIT_SP - 0x00020000
> -
> -#define CONFIG_SYS_HUSH_PARSER
> -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
> -
> -#endif /* __CONFIG_H */
> diff --git a/include/configs/EP1S40.h b/include/configs/EP1S40.h
> deleted file mode 100644
> index 4d905fe..0000000
> --- a/include/configs/EP1S40.h
> +++ /dev/null
> @@ -1,207 +0,0 @@
> -/*
> - * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
> - * Scott McNutt <smcnutt@psyent.com>
> - *
> - * See file CREDITS for list of people who contributed to this
> - * project.
> - *
> - * This program is free software; you can redistribute it and/or
> - * modify it under the terms of the GNU General Public License as
> - * published by the Free Software Foundation; either version 2 of
> - * the License, or (at your option) any later version.
> - *
> - * This program is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> - * GNU General Public License for more details.
> - *
> - * You should have received a copy of the GNU General Public License
> - * along with this program; if not, write to the Free Software
> - * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> - * MA 02111-1307 USA
> - */
> -
> -#ifndef __CONFIG_H
> -#define __CONFIG_H
> -
> -/*------------------------------------------------------------------------
> - * BOARD/CPU
> - *----------------------------------------------------------------------*/
> -#define CONFIG_EP1S40 1 /* EP1S40 board */
> -#define CONFIG_SYS_CLK_FREQ 50000000 /* 50 MHz core clk */
> -
> -#define CONFIG_SYS_RESET_ADDR 0x00000000 /* Hard-reset address */
> -#define CONFIG_SYS_EXCEPTION_ADDR 0x01000020 /* Exception entry point*/
> -#define CONFIG_SYS_NIOS_SYSID_BASE 0x021208b8 /* System id address */
> -
> -/*------------------------------------------------------------------------
> - * CACHE -- the following will support II/s and II/f. The II/s does not
> - * have dcache, so the cache instructions will behave as NOPs.
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_ICACHE_SIZE 4096 /* 4 KByte total */
> -#define CONFIG_SYS_ICACHELINE_SIZE 32 /* 32 bytes/line */
> -#define CONFIG_SYS_DCACHE_SIZE 2048 /* 2 KByte (II/f) */
> -#define CONFIG_SYS_DCACHELINE_SIZE 4 /* 4 bytes/line (II/f) */
> -
> -/*------------------------------------------------------------------------
> - * MEMORY BASE ADDRESSES
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_FLASH_BASE 0x00000000 /* FLASH base addr */
> -#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */
> -#define CONFIG_SYS_SDRAM_BASE 0x01000000 /* SDRAM base addr */
> -#define CONFIG_SYS_SDRAM_SIZE 0x01000000 /* 16 MByte */
> -#define CONFIG_SYS_SRAM_BASE 0x02000000 /* SRAM base addr */
> -#define CONFIG_SYS_SRAM_SIZE 0x00100000 /* 1 MB */
> -
> -/*------------------------------------------------------------------------
> - * MEMORY ORGANIZATION
> - * -Monitor at top.
> - * -The heap is placed below the monitor.
> - * -Global data is placed below the heap.
> - * -The stack is placed below global data (&grows down).
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256k */
> -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Global data size rsvd*/
> -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 256*1024) /* 256k heap */
> -
> -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
> -#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
> -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
> -#define CONFIG_SYS_INIT_SP CONFIG_SYS_GBL_DATA_OFFSET
> -
> -/*------------------------------------------------------------------------
> - * FLASH (AM29LV065D)
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* Max # sects per bank */
> -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max # of flash banks */
> -#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Erase timeout (msec) */
> -#define CONFIG_SYS_FLASH_WRITE_TOUT 100 /* Write timeout (msec) */
> -
> -/*------------------------------------------------------------------------
> - * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above
> - * CONFIG_SYS_FLASH_BASE, since we assume that u-boot is stored at the bottom
> - * of flash memory. This will keep the environment in user region
> - * of flash. NOTE: the monitor length must be multiple of sector size
> - * (which is common practice).
> - *----------------------------------------------------------------------*/
> -#define CONFIG_ENV_IS_IN_FLASH 1 /* Environment in flash */
> -#define CONFIG_ENV_SIZE (64 * 1024) /* 64 KByte (1 sector) */
> -#define CONFIG_ENV_OVERWRITE /* Serial change Ok */
> -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
> -
> -/*------------------------------------------------------------------------
> - * CONSOLE
> - *----------------------------------------------------------------------*/
> -#define CONFIG_ALTERA_UART 1 /* Use altera uart */
> -#if defined(CONFIG_ALTERA_JTAG_UART)
> -#define CONFIG_SYS_NIOS_CONSOLE 0x021208b0 /* JTAG UART base addr */
> -#else
> -#define CONFIG_SYS_NIOS_CONSOLE 0x02120840 /* UART base addr */
> -#endif
> -
> -#define CONFIG_SYS_NIOS_FIXEDBAUD 1 /* Baudrate is fixed */
> -#define CONFIG_BAUDRATE 115200 /* Initial baudrate */
> -#define CONFIG_SYS_BAUDRATE_TABLE {115200} /* It's fixed ;-) */
> -
> -#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* Suppress console info*/
> -
> -/*------------------------------------------------------------------------
> - * EPCS Device -- None for stratix.
> - *----------------------------------------------------------------------*/
> -#undef CONFIG_SYS_NIOS_EPCSBASE
> -
> -/*------------------------------------------------------------------------
> - * DEBUG
> - *----------------------------------------------------------------------*/
> -#undef CONFIG_ROM_STUBS /* Stubs not in ROM */
> -
> -/*------------------------------------------------------------------------
> - * TIMEBASE --
> - *
> - * The high res timer defaults to 1 msec. Since it includes the period
> - * registers, the interrupt frequency can be reduced using TMRCNT.
> - * If the default period is acceptable, TMRCNT can be left undefined.
> - * TMRMS represents the desired mecs per tick (msecs per interrupt).
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_HZ 1000 /* Always 1000 */
> -#define CONFIG_SYS_NIOS_TMRBASE 0x02120820 /* Tick timer base addr */
> -#define CONFIG_SYS_NIOS_TMRIRQ 3 /* Timer IRQ num */
> -#define CONFIG_SYS_NIOS_TMRMS 10 /* Desired period (msec) */
> -#define CONFIG_SYS_NIOS_TMRCNT \
> - (CONFIG_SYS_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000))
> -
> -/*------------------------------------------------------------------------
> - * STATUS LED -- Provides a simple blinking led. For Nios2 each board
> - * must implement its own led routines -- since leds are board-specific.
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_LEDPIO_ADDR 0x02120870 /* LED PIO base addr */
> -#define CONFIG_STATUS_LED /* Enable status driver */
> -
> -#define STATUS_LED_BIT 1 /* Bit-0 on PIO */
> -#define STATUS_LED_STATE 1 /* Blinking */
> -#define STATUS_LED_PERIOD (500/CONFIG_SYS_NIOS_TMRMS) /* Every 500 msec */
> -
> -/*------------------------------------------------------------------------
> - * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ...
> - * and really doesn't need any additional clutter. So I choose the lazy
> - * way out to avoid changes there -- define the base address to ensure
> - * cache bypass so there's no need to monkey with inx/outx macros.
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SMC91111_BASE 0x82110300 /* Base addr (bypass) */
> -#define CONFIG_NET_MULTI
> -#define CONFIG_SMC91111 /* Using SMC91c111 */
> -#undef CONFIG_SMC91111_EXT_PHY /* Internal PHY */
> -#define CONFIG_SMC_USE_32_BIT /* 32-bit interface */
> -
> -#define CONFIG_ETHADDR 08:00:3e:26:0a:5b
> -#define CONFIG_NETMASK 255.255.255.0
> -#define CONFIG_IPADDR 192.168.2.21
> -#define CONFIG_SERVERIP 192.168.2.16
> -
> -
> -/*
> - * BOOTP options
> - */
> -#define CONFIG_BOOTP_BOOTFILESIZE
> -#define CONFIG_BOOTP_BOOTPATH
> -#define CONFIG_BOOTP_GATEWAY
> -#define CONFIG_BOOTP_HOSTNAME
> -
> -
> -/*
> - * Command line configuration.
> - */
> -#define CONFIG_CMD_BDI
> -#define CONFIG_CMD_DHCP
> -#define CONFIG_CMD_ECHO
> -#define CONFIG_CMD_SAVEENV
> -#define CONFIG_CMD_FLASH
> -#define CONFIG_CMD_IMI
> -#define CONFIG_CMD_IRQ
> -#define CONFIG_CMD_LOADS
> -#define CONFIG_CMD_LOADB
> -#define CONFIG_CMD_MEMORY
> -#define CONFIG_CMD_MISC
> -#define CONFIG_CMD_NET
> -#define CONFIG_CMD_PING
> -#define CONFIG_CMD_RUN
> -#define CONFIG_CMD_SAVES
> -
> -
> -/*------------------------------------------------------------------------
> - * MISC
> - *----------------------------------------------------------------------*/
> -#define CONFIG_SYS_LONGHELP /* Provide extended help*/
> -#define CONFIG_SYS_PROMPT "==> " /* Command prompt */
> -#define CONFIG_SYS_CBSIZE 256 /* Console I/O buf size */
> -#define CONFIG_SYS_MAXARGS 16 /* Max command args */
> -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot arg buf size */
> -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buf size */
> -#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE /* Default load address */
> -#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE /* Start addr for test */
> -#define CONFIG_SYS_MEMTEST_END CONFIG_SYS_INIT_SP - 0x00020000
> -
> -#define CONFIG_SYS_HUSH_PARSER
> -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
> -
> -#endif /* __CONFIG_H */
^ permalink raw reply [flat|nested] 2+ messages in thread