From: Heiko Schocher <hs@denx.de>
To: u-boot@lists.denx.de
Subject: [U-Boot] ARM relocation, probably trivial mistake
Date: Thu, 30 Sep 2010 17:39:08 +0200 [thread overview]
Message-ID: <4CA4AF1C.7080104@denx.de> (raw)
In-Reply-To: <4CA49CC2.2030904@emk-elektronik.de>
Hello Reinhard,
Reinhard Meyer wrote:
> Dear Stefano Babic,
>>> 1. should CONFIG_SKIP_RELOCATE_UBOOT be not defined anymore?
>> I had the same issue because I forget to remove it from my config file.
>> After dropping it, I got the u-boot prompt again ;-)
> Thank you, that (partially) helped:
>
> U-Boot 2010.09-00106-g6e135b9-dirty (Sep 30 2010 - 17:32:36)
>
> U-Boot code: 21F00000 -> 21F3C180 BSS: -> 21F7D700
> CPU: AT91SAM9XE
> Crystal frequency: 18.432 MHz
> CPU clock : 198.656 MHz
> Master clock : 99.328 MHz
> I2C: ready
> monitor len: 0007D700
> ramsize: 04000000
> Top of RAM usable for U-Boot at: 24000000
> Reserving 501k for U-Boot at: 23f82000
> Reserving 143k for malloc() at: 23f5e100
> Reserving 24 Bytes for Board Info at: 23f5e0e8
> Reserving 88 Bytes for Global Data at: 23f5e090
> New Stack Pointer is: 23f5e088
> RAM Configuration:
> Bank #0: 20000000 64 MiB
> relocation Offset is: 02082000
> monitor flash len: 0003C180
> Now running in RAM - U-Boot at: 23f82000
> FLASH: 512 KiB
> NAND: raise: Signal # 8 caught
> raise: Signal # 8 caught
> raise: Signal # 8 caught
> 256 MiB
> *** Warning - bad CRC, using default environment
>
> In: serial
> Out: serial
> Err: serial
> MMC: mci: 0
> Net: macb0, enc1.0, enc1.1, enc1.2
> Reset Ethernet PHY
> macb0: Starting autonegotiation...
> macb0: Autonegotiation timed out (status=0x7849)
> macb0: link down (status: 0x7849)
> enc1.0: timeout waiting for CLKRDY
> enc1.1: timeout waiting for CLKRDY
> enc1.2: timeout waiting for CLKRDY
> Press SPACE to abort autoboot in 1 seconds
>
> Before the relocation: macb, enc and environment did work :)
> I have to look into that issue later...
No spontaneous idea ... maybe something with gpio pins?
bye,
Heiko
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
next prev parent reply other threads:[~2010-09-30 15:39 UTC|newest]
Thread overview: 113+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-09-30 13:57 [U-Boot] ARM relocation, probably trivial mistake Reinhard Meyer
2010-09-30 14:08 ` Stefano Babic
2010-09-30 14:20 ` Reinhard Meyer
2010-09-30 15:39 ` Heiko Schocher [this message]
2010-09-30 16:06 ` Reinhard Meyer
2010-09-30 15:38 ` Heiko Schocher
2010-09-30 17:43 ` Wolfgang Denk
2010-10-01 5:25 ` Heiko Schocher
2010-10-01 5:40 ` Albert ARIBAUD
2010-10-01 5:53 ` Heiko Schocher
2010-10-01 6:39 ` Reinhard Meyer
2010-10-01 6:57 ` Heiko Schocher
2010-10-01 8:45 ` Wolfgang Denk
2010-10-01 7:01 ` Albert ARIBAUD
2010-10-01 7:42 ` [U-Boot] ARM relocation, probably trivial mistake - back to original problem Reinhard Meyer
2010-10-01 8:27 ` Heiko Schocher
2010-10-01 10:44 ` Reinhard Meyer
2010-10-01 10:55 ` Wolfgang Denk
2010-10-01 11:03 ` Reinhard Meyer
2010-10-01 11:21 ` Wolfgang Denk
2010-10-01 11:37 ` Reinhard Meyer
2010-10-01 11:59 ` Wolfgang Denk
2010-10-01 12:22 ` Reinhard Meyer
2010-10-01 12:47 ` Reinhard Meyer
2010-10-01 12:55 ` Wolfgang Denk
2010-10-01 14:55 ` Reinhard Meyer
2010-10-02 8:53 ` Heiko Schocher
2010-10-01 15:47 ` Steve Sakoman
2010-10-02 7:15 ` [U-Boot] ARM relocation, question to Heiko Reinhard Meyer
[not found] ` <4CA6E517.9040701@fr<1286167382.22760.19.camel@ptyser-laptop>
2010-10-02 7:53 ` Albert ARIBAUD
2010-10-02 8:10 ` Reinhard Meyer
2010-10-02 8:26 ` Albert ARIBAUD
2010-10-03 18:04 ` Wolfgang Denk
2010-10-02 9:08 ` Heiko Schocher
2010-10-02 9:29 ` Albert ARIBAUD
2010-10-03 18:05 ` Wolfgang Denk
2010-10-02 10:17 ` Joakim Tjernlund
2010-10-02 16:21 ` J. William Campbell
2010-10-02 18:33 ` Reinhard Meyer
2010-10-03 18:22 ` Wolfgang Denk
2010-10-02 20:39 ` Reinhard Meyer
2010-10-02 21:09 ` Albert ARIBAUD
2010-10-02 23:07 ` Graeme Russ
2010-10-03 7:10 ` Albert ARIBAUD
2010-10-03 8:44 ` Graeme Russ
2010-10-03 8:58 ` Albert ARIBAUD
2010-10-03 15:36 ` J. William Campbell
2010-10-03 16:47 ` Albert ARIBAUD
2010-10-03 17:54 ` Albert ARIBAUD
2010-10-03 18:43 ` Wolfgang Denk
2010-10-04 5:41 ` Heiko Schocher
2010-10-03 18:29 ` Wolfgang Denk
2010-10-03 19:26 ` J. William Campbell
2010-10-04 5:52 ` Heiko Schocher
2010-10-03 18:14 ` Wolfgang Denk
2010-10-03 18:54 ` J. William Campbell
2010-10-03 19:52 ` Albert ARIBAUD
2010-10-03 18:03 ` Wolfgang Denk
2010-10-03 18:34 ` Albert ARIBAUD
2010-10-03 18:45 ` Wolfgang Denk
2010-10-04 6:08 ` Heiko Schocher
2010-10-04 6:40 ` Albert ARIBAUD
2010-10-04 7:27 ` Reinhard Meyer
2010-10-04 8:28 ` Albert ARIBAUD
2010-10-04 8:57 ` Heiko Schocher
2010-10-04 9:27 ` Albert ARIBAUD
2010-10-04 10:01 ` Joakim Tjernlund
2010-10-04 9:58 ` Graeme Russ
2010-10-04 14:17 ` Albert ARIBAUD
2010-10-04 14:25 ` Rogan Dawes
2010-10-04 15:24 ` Albert ARIBAUD
2010-10-04 16:31 ` Stefan Roese
2010-10-04 21:31 ` Albert ARIBAUD
2010-10-04 7:44 ` Albert ARIBAUD
2010-10-04 4:43 ` Peter Tyser
2010-10-04 6:08 ` Wolfgang Denk
2010-10-04 7:36 ` Joakim Tjernlund
2010-10-04 8:08 ` Albert ARIBAUD
2010-10-04 8:28 ` Joakim Tjernlund
2010-10-04 8:33 ` Albert ARIBAUD
[not found] ` <OF05779DA1.EF3C4954-ONC12577B2.00307A0D-C12577B2.0030B9C0@tran <4CAA1613.80002@comcast.net>
2010-10-04 8:52 ` Joakim Tjernlund
2010-10-04 9:10 ` Albert ARIBAUD
2010-10-04 10:13 ` Wolfgang Denk
2010-10-04 15:28 ` J. William Campbell
2010-10-04 15:52 ` Albert ARIBAUD
2010-10-04 17:06 ` Wolfgang Denk
2010-10-04 17:59 ` J. William Campbell
2010-10-04 18:43 ` Joakim Tjernlund
2010-10-04 21:10 ` Wolfgang Denk
2010-10-05 7:26 ` Joakim Tjernlund
2010-10-04 17:04 ` Graeme Russ
2010-10-04 17:14 ` Wolfgang Denk
2010-10-04 8:27 ` Wolfgang Denk
2010-10-02 8:49 ` [U-Boot] ARM relocation, probably trivial mistake - back to original problem Heiko Schocher
2010-10-01 12:49 ` Wolfgang Denk
2010-10-01 14:48 ` Reinhard Meyer
2010-10-04 7:44 ` [U-Boot] AT91 clock and timer cleanups (was: ARM relocation, probably trivial mistake - back to original problem) Reinhard Meyer
2010-10-04 8:32 ` Wolfgang Denk
2010-10-04 8:42 ` [U-Boot] AT91 clock and timer cleanups Reinhard Meyer
2010-10-04 8:49 ` Wolfgang Denk
2010-10-04 8:52 ` Reinhard Meyer
2010-10-04 9:03 ` Wolfgang Denk
2010-10-04 9:12 ` Reinhard Meyer
2010-10-04 14:58 ` Reinhard Meyer
2010-10-04 17:00 ` Wolfgang Denk
2010-10-04 17:15 ` Reinhard Meyer
2010-10-04 17:32 ` Wolfgang Denk
2010-10-04 19:22 ` Reinhard Meyer
2010-10-01 8:48 ` [U-Boot] ARM relocation, probably trivial mistake - back to original problem Wolfgang Denk
2010-10-01 9:50 ` Reinhard Meyer
2010-10-01 8:03 ` [U-Boot] ARM relocation, probably trivial mistake Wolfgang Denk
2010-10-01 7:51 ` Wolfgang Denk
2010-10-01 8:28 ` Heiko Schocher
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4CA4AF1C.7080104@denx.de \
--to=hs@denx.de \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox