[U-Boot] USB: EHCI reports EHCI fail timeout STD_ASS reset

[U-Boot] USB: EHCI reports EHCI fail timeout STD_ASS reset

[Stefano Babic]

Hi all,

I am adding EHCI support to the MX.31 Soc. I got an error from the
ehci-hcd controller, that seems (apparently!) to not depend by the Soc I
am using.

"usb start" works as expected:

CPU:   Freescale i.MX31 at 398 MHz
Board: DAVE/DENX Qong
DRAM:  256 MiB
FLASH: 128 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
FPGA:  version register = 0.8.7
Net:   dnet0
Hit any key to stop autoboot:  0
=> usb start
(Re)start USB...
USB:   Writing USBH2 port 0x40004020
Writing USBH2 port 0x40004020
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found

And usb info reports correct values:
=> usb info
1: Hub,  USB Revision 2.0
 - u-boot EHCI Host Controller
 - Class: Hub
 - PacketSize: 64  Configurations: 1
 - Vendor: 0x0000  Product 0x0000 Version 1.0
   Configuration: 1
   - Interfaces: 1 Self Powered 0mA
     Interface: 0
     - Alternate Setting 0, Endpoints: 1
     - Class Hub
     - Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms

2: Mass Storage,  USB Revision 2.0
 - Kingston DataTraveler 2.0 001D0F0A94C25B89070F1158
 - Class: (from Interface) Mass Storage
 - PacketSize: 64  Configurations: 1
 - Vendor: 0x0930  Product 0x6545 Version 1.0
   Configuration: 1
   - Interfaces: 1 Bus Powered 200mA
     Interface: 0
     - Alternate Setting 0, Endpoints: 2
     - Class Mass Storage, Transp. SCSI, Bulk only
     - Endpoint 1 In Bulk MaxPacket 512
     - Endpoint 2 Out Bulk MaxPacket 512

I can read the directory structure of the USB stick:

=> fatload usb 0 80000000 doc/qong-hm.pdf
reading doc/qong-hm.pdf

or load some files:

fatload usb 0 80000000 doc/qong-hm.pdf
reading doc/qong-hm.pdf

3145354 bytes read

until the following error is raised:

EHCI fail timeout STD_ASS reset

The error does not happen each time. Sometimes at the first
fatls/fatload attempt, sometimes I need several tries to get it. When it
happens, the usb controller becomes unavailable and I have to reset the
system. I traced the value of the usbsts (status) register when the
error occurs:

handshake fails 0xa088

The AS bit is really set, and it does not go away as it is supposed to
do. The RCL (reclamation) and FRI (frame list rollover) are set too, but
I do not know if they are a consequence of the fact the ASE bit is not
reset by the controller or a cause.

I found in the ML someone reporting the same error, but it seems to me
it was related to USB on PCI controllers, and that is not my case.

Any hints ?

Stefano

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================

[U-Boot] USB: EHCI reports EHCI fail timeout STD_ASS reset

[Stefano Babic]

Stefano Babic wrote:
> Hi all,
> 
> I am adding EHCI support to the MX.31 Soc. I got an error from the
> ehci-hcd controller, that seems (apparently!) to not depend by the Soc I
> am using.

In the meantime I discovered this is an HW failure - with an external
USB HUB the problem disappears.

Stefano

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================