[U-Boot] [PATCH] smc91111: add write_hwaddr

[U-Boot] [PATCH] smc91111: add write_hwaddr

[Thomas Chou]

Add smc_write_hwaddr() to set mac address.
Clear dev before use.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
---
 drivers/net/smc91111.c |   40 ++++++++++++++++++++++++----------------
 1 files changed, 24 insertions(+), 16 deletions(-)

diff --git a/drivers/net/smc91111.c b/drivers/net/smc91111.c
index 54a1bfb..ba9c67e 100644
--- a/drivers/net/smc91111.c
+++ b/drivers/net/smc91111.c
@@ -654,6 +654,28 @@ again:
 	return length;
 }
 
+static int smc_write_hwaddr(struct eth_device *dev)
+{
+	int i;
+
+	swap_to(ETHERNET);
+	SMC_SELECT_BANK (dev, 1);
+#ifdef USE_32_BIT
+	for (i = 0; i < 6; i += 2) {
+		word address;
+
+		address = dev->enetaddr[i + 1] << 8;
+		address |= dev->enetaddr[i];
+		SMC_outw(dev, address, (ADDR0_REG + i));
+	}
+#else
+	for (i = 0; i < 6; i++)
+		SMC_outb(dev, dev->enetaddr[i], (ADDR0_REG + i));
+#endif
+	swap_to(FLASH);
+	return 0;
+}
+
 /*
  * Open and Initialize the board
  *
@@ -662,8 +684,6 @@ again:
  */
 static int smc_init(struct eth_device *dev, bd_t *bd)
 {
-	int i;
-
 	swap_to(ETHERNET);
 
 	PRINTK2 ("%s: smc_init\n", SMC_DEV_NAME);
@@ -680,20 +700,6 @@ static int smc_init(struct eth_device *dev, bd_t *bd)
 	/* conservative setting (10Mbps, HalfDuplex, no AutoNeg.) */
 /*	SMC_SELECT_BANK(dev, 0); */
 /*	SMC_outw(dev, 0, RPC_REG); */
-	SMC_SELECT_BANK (dev, 1);
-
-#ifdef USE_32_BIT
-	for (i = 0; i < 6; i += 2) {
-		word address;
-
-		address = dev->enetaddr[i + 1] << 8;
-		address |= dev->enetaddr[i];
-		SMC_outw(dev, address, (ADDR0_REG + i));
-	}
-#else
-	for (i = 0; i < 6; i++)
-		SMC_outb(dev, dev->enetaddr[i], (ADDR0_REG + i));
-#endif
 
 	printf(SMC_DEV_NAME ": MAC %pM\n", dev->enetaddr);
 
@@ -1360,6 +1366,7 @@ int smc91111_initialize(u8 dev_num, int base_addr)
 		return 0;
 	}
 
+	memset(dev, 0, sizeof(*dev));
 	priv->dev_num = dev_num;
 	dev->priv = priv;
 	dev->iobase = base_addr;
@@ -1374,6 +1381,7 @@ int smc91111_initialize(u8 dev_num, int base_addr)
 	dev->halt = smc_halt;
 	dev->send = smc_send;
 	dev->recv = smc_rcv;
+	dev->write_hwaddr = smc_write_hwaddr;
 	sprintf(dev->name, "%s-%hu", SMC_DEV_NAME, dev_num);
 
 	eth_register(dev);
-- 
1.7.1.86.g0e460

[U-Boot] [PATCH] smc91111: add write_hwaddr

[Mike Frysinger]

On Tuesday, October 05, 2010 21:16:10 Thomas Chou wrote:
> Add smc_write_hwaddr() to set mac address.
> Clear dev before use.

how is this different from the one sent earlier today ?  when re-submitting, 
you should note what changed.
-mike
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: This is a digitally signed message part.
Url : http://lists.denx.de/pipermail/u-boot/attachments/20101005/f5b49162/attachment.pgp 

[U-Boot] [PATCH] smc91111: add write_hwaddr

[Thomas Chou]

Mike Frysinger wrote:
> On Tuesday, October 05, 2010 21:16:10 Thomas Chou wrote:
>> Add smc_write_hwaddr() to set mac address.
>> Clear dev before use.
> 
> how is this different from the one sent earlier today ?  when re-submitting, 
> you should note what changed.
> -mike
Sorry. It is the same patch resend.

I was confused by the greylisting of denx mail server and wondered why 
the first mail was not received after 12 hours.

- Thomas

[U-Boot] [PATCH] smc91111: add write_hwaddr

[Wolfgang Denk]

Dear Thomas Chou,

In message <4CAC0B1E.1050007@wytron.com.tw> you wrote:
>
> I was confused by the greylisting of denx mail server and wondered why 
> the first mail was not received after 12 hours.

There is no greylisting on our side.

Best regards,

Wolfgang Denk

-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
There is is no reason for any individual to have a computer in  their
home.      -- Ken Olsen (President of Digital Equipment Corporation),
              Convention of the World Future Society, in Boston, 1977

[U-Boot] [PATCH] smc91111: add write_hwaddr

[Detlev Zundel]

Hi Wolfgang,

> Dear Thomas Chou,
>
> In message <4CAC0B1E.1050007@wytron.com.tw> you wrote:
>>
>> I was confused by the greylisting of denx mail server and wondered why 
>> the first mail was not received after 12 hours.
>
> There is no greylisting on our side.

Well actually we do run postgrey.  But as yet we did not get any
complaints that this interferes with regular usage.  The default values
of the software should not intrude much on completely unfiltered
traffic.

Cheers
  Detlev

-- 
A change in language can transform our appreciation of the cosmos
                       -- Benjamin Lee Whorf
--
DENX Software Engineering GmbH,      MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich,  Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-40 Fax: (+49)-8142-66989-80 Email: dzu at denx.de

[U-Boot] [PATCH] smc91111: add write_hwaddr

[Thomas Chou]

On 10/07/2010 06:27 PM, Detlev Zundel wrote:
> Hi Wolfgang,
>
>> Dear Thomas Chou,
>>
>> In message<4CAC0B1E.1050007@wytron.com.tw>  you wrote:
>>>
>>> I was confused by the greylisting of denx mail server and wondered why
>>> the first mail was not received after 12 hours.
>>
>> There is no greylisting on our side.
>
> Well actually we do run postgrey.  But as yet we did not get any
> complaints that this interferes with regular usage.  The default values
> of the software should not intrude much on completely unfiltered
> traffic.

Dear Wolfgang and Detlev,

The retransmission wait time on my first mail server is quite long and I 
forgot that there is postgrey on denx mail server, so I sent the patch 
again using another mail server. I wondered if my first mail server 
changed IP. Sorry for the noise.

Best regards,
Thomas

[U-Boot] [PATCH] smc91111: add write_hwaddr

[Wolfgang Denk]

Dear Thomas Chou,

In message <4CAEC4CD.6050705@wytron.com.tw> you wrote:
>
> The retransmission wait time on my first mail server is quite long and I 
> forgot that there is postgrey on denx mail server, so I sent the patch 
> again using another mail server. I wondered if my first mail server 
> changed IP. Sorry for the noise.

No problem.  It was informative for me, too, as I learned that we're
running postgrey. I didn't know that before.

Best regards,

Wolfgang Denk

-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
The game of life is a game of boomerangs.  Our  thoughts,  deeds  and
words return to us sooner or later with astounding accuracy.

[U-Boot] [PATCH] smc91111: add write_hwaddr

[Ben Warren]

  Hi Thomas,

On 10/5/2010 6:16 PM, Thomas Chou wrote:
> Add smc_write_hwaddr() to set mac address.
> Clear dev before use.
>
> Signed-off-by: Thomas Chou<thomas@wytron.com.tw>
> ---
>   drivers/net/smc91111.c |   40 ++++++++++++++++++++++++----------------
>   1 files changed, 24 insertions(+), 16 deletions(-)
Applied to net repo.

thanks,
Ben

[U-Boot] [PATCH] smc91111: add write_hwaddr

[Thomas Chou]

Add smc_write_hwaddr() to set mac address.
Clear dev before use.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
---
 drivers/net/smc91111.c |   40 ++++++++++++++++++++++++----------------
 1 files changed, 24 insertions(+), 16 deletions(-)

diff --git a/drivers/net/smc91111.c b/drivers/net/smc91111.c
index 54a1bfb..ba9c67e 100644
--- a/drivers/net/smc91111.c
+++ b/drivers/net/smc91111.c
@@ -654,6 +654,28 @@ again:
 	return length;
 }
 
+static int smc_write_hwaddr(struct eth_device *dev)
+{
+	int i;
+
+	swap_to(ETHERNET);
+	SMC_SELECT_BANK (dev, 1);
+#ifdef USE_32_BIT
+	for (i = 0; i < 6; i += 2) {
+		word address;
+
+		address = dev->enetaddr[i + 1] << 8;
+		address |= dev->enetaddr[i];
+		SMC_outw(dev, address, (ADDR0_REG + i));
+	}
+#else
+	for (i = 0; i < 6; i++)
+		SMC_outb(dev, dev->enetaddr[i], (ADDR0_REG + i));
+#endif
+	swap_to(FLASH);
+	return 0;
+}
+
 /*
  * Open and Initialize the board
  *
@@ -662,8 +684,6 @@ again:
  */
 static int smc_init(struct eth_device *dev, bd_t *bd)
 {
-	int i;
-
 	swap_to(ETHERNET);
 
 	PRINTK2 ("%s: smc_init\n", SMC_DEV_NAME);
@@ -680,20 +700,6 @@ static int smc_init(struct eth_device *dev, bd_t *bd)
 	/* conservative setting (10Mbps, HalfDuplex, no AutoNeg.) */
 /*	SMC_SELECT_BANK(dev, 0); */
 /*	SMC_outw(dev, 0, RPC_REG); */
-	SMC_SELECT_BANK (dev, 1);
-
-#ifdef USE_32_BIT
-	for (i = 0; i < 6; i += 2) {
-		word address;
-
-		address = dev->enetaddr[i + 1] << 8;
-		address |= dev->enetaddr[i];
-		SMC_outw(dev, address, (ADDR0_REG + i));
-	}
-#else
-	for (i = 0; i < 6; i++)
-		SMC_outb(dev, dev->enetaddr[i], (ADDR0_REG + i));
-#endif
 
 	printf(SMC_DEV_NAME ": MAC %pM\n", dev->enetaddr);
 
@@ -1360,6 +1366,7 @@ int smc91111_initialize(u8 dev_num, int base_addr)
 		return 0;
 	}
 
+	memset(dev, 0, sizeof(*dev));
 	priv->dev_num = dev_num;
 	dev->priv = priv;
 	dev->iobase = base_addr;
@@ -1374,6 +1381,7 @@ int smc91111_initialize(u8 dev_num, int base_addr)
 	dev->halt = smc_halt;
 	dev->send = smc_send;
 	dev->recv = smc_rcv;
+	dev->write_hwaddr = smc_write_hwaddr;
 	sprintf(dev->name, "%s-%hu", SMC_DEV_NAME, dev_num);
 
 	eth_register(dev);
-- 
1.7.1.86.g0e460

[U-Boot] [PATCH] smc91111: add write_hwaddr

[Mike Frysinger]

On Tuesday, October 05, 2010 03:30:33 Thomas Chou wrote:
> Add smc_write_hwaddr() to set mac address.
> Clear dev before use.

Acked-by: Mike Frysinger <vapier@gentoo.org>
-mike
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: This is a digitally signed message part.
Url : http://lists.denx.de/pipermail/u-boot/attachments/20101005/2c78f00d/attachment.pgp