* [U-Boot] [PATCH 1/3] MX31: add support for setting pin pads
@ 2010-10-07 9:27 Stefano Babic
2010-10-07 9:27 ` [U-Boot] [PATCH 2/3] MX31: Add support for MXC EHCI controller Stefano Babic
0 siblings, 1 reply; 6+ messages in thread
From: Stefano Babic @ 2010-10-07 9:27 UTC (permalink / raw)
To: u-boot
The patch adds a utility function and defines
to set the pad as it is done in linux.
Signed-off-by: Stefano Babic <sbabic@denx.de>
---
arch/arm/cpu/arm1136/mx31/generic.c | 17 ++
arch/arm/include/asm/arch-mx31/mx31-regs.h | 404 ++++++++++++++++++++++++++++
drivers/video/mx3fb.c | 31 ---
3 files changed, 421 insertions(+), 31 deletions(-)
diff --git a/arch/arm/cpu/arm1136/mx31/generic.c b/arch/arm/cpu/arm1136/mx31/generic.c
index 1415d6c..cbe8243 100644
--- a/arch/arm/cpu/arm1136/mx31/generic.c
+++ b/arch/arm/cpu/arm1136/mx31/generic.c
@@ -23,6 +23,7 @@
#include <common.h>
#include <asm/arch/mx31-regs.h>
+#include <asm/io.h>
static u32 mx31_decode_pll(u32 reg, u32 infreq)
{
@@ -90,6 +91,22 @@ void mx31_gpio_mux(unsigned long mode)
__REG(reg) = tmp;
}
+void mx31_set_pad(enum iomux_pins pin, u32 config)
+{
+ u32 field, l;
+ void *reg;
+
+ pin &= IOMUX_PADNUM_MASK;
+ reg = (IOMUXC_BASE + 0x154) + (pin + 2) / 3 * 4;
+ field = (pin + 2) % 3;
+
+ l = __raw_readl(reg);
+ l &= ~(0x1ff << (field * 10));
+ l |= config << (field * 10);
+ __raw_writel(l, reg);
+
+}
+
#if defined(CONFIG_DISPLAY_CPUINFO)
int print_cpuinfo (void)
{
diff --git a/arch/arm/include/asm/arch-mx31/mx31-regs.h b/arch/arm/include/asm/arch-mx31/mx31-regs.h
index 7a98d1c..46ed47c 100644
--- a/arch/arm/include/asm/arch-mx31/mx31-regs.h
+++ b/arch/arm/include/asm/arch-mx31/mx31-regs.h
@@ -64,6 +64,370 @@ struct gpio_regs {
u32 gpio_psr;
};
+#define IOMUX_PADNUM_MASK 0x1ff
+#define IOMUX_PIN(gpionum, padnum) ((padnum) & IOMUX_PADNUM_MASK)
+
+/*
+ * various IOMUX pad functions
+ */
+enum iomux_pad_config {
+ PAD_CTL_NOLOOPBACK = 0x0 << 9,
+ PAD_CTL_LOOPBACK = 0x1 << 9,
+ PAD_CTL_PKE_NONE = 0x0 << 8,
+ PAD_CTL_PKE_ENABLE = 0x1 << 8,
+ PAD_CTL_PUE_KEEPER = 0x0 << 7,
+ PAD_CTL_PUE_PUD = 0x1 << 7,
+ PAD_CTL_100K_PD = 0x0 << 5,
+ PAD_CTL_100K_PU = 0x1 << 5,
+ PAD_CTL_47K_PU = 0x2 << 5,
+ PAD_CTL_22K_PU = 0x3 << 5,
+ PAD_CTL_HYS_CMOS = 0x0 << 4,
+ PAD_CTL_HYS_SCHMITZ = 0x1 << 4,
+ PAD_CTL_ODE_CMOS = 0x0 << 3,
+ PAD_CTL_ODE_OpenDrain = 0x1 << 3,
+ PAD_CTL_DRV_NORMAL = 0x0 << 1,
+ PAD_CTL_DRV_HIGH = 0x1 << 1,
+ PAD_CTL_DRV_MAX = 0x2 << 1,
+ PAD_CTL_SRE_SLOW = 0x0 << 0,
+ PAD_CTL_SRE_FAST = 0x1 << 0
+};
+
+/*
+ * This enumeration is constructed based on the Section
+ * "sw_pad_ctl & sw_mux_ctl details" of the MX31 IC Spec. Each enumerated
+ * value is constructed based on the rules described above.
+ */
+
+enum iomux_pins {
+ MX31_PIN_TTM_PAD = IOMUX_PIN(0xff, 0),
+ MX31_PIN_CSPI3_SPI_RDY = IOMUX_PIN(0xff, 1),
+ MX31_PIN_CSPI3_SCLK = IOMUX_PIN(0xff, 2),
+ MX31_PIN_CSPI3_MISO = IOMUX_PIN(0xff, 3),
+ MX31_PIN_CSPI3_MOSI = IOMUX_PIN(0xff, 4),
+ MX31_PIN_CLKSS = IOMUX_PIN(0xff, 5),
+ MX31_PIN_CE_CONTROL = IOMUX_PIN(0xff, 6),
+ MX31_PIN_ATA_RESET_B = IOMUX_PIN(95, 7),
+ MX31_PIN_ATA_DMACK = IOMUX_PIN(94, 8),
+ MX31_PIN_ATA_DIOW = IOMUX_PIN(93, 9),
+ MX31_PIN_ATA_DIOR = IOMUX_PIN(92, 10),
+ MX31_PIN_ATA_CS1 = IOMUX_PIN(91, 11),
+ MX31_PIN_ATA_CS0 = IOMUX_PIN(90, 12),
+ MX31_PIN_SD1_DATA3 = IOMUX_PIN(63, 13),
+ MX31_PIN_SD1_DATA2 = IOMUX_PIN(62, 14),
+ MX31_PIN_SD1_DATA1 = IOMUX_PIN(61, 15),
+ MX31_PIN_SD1_DATA0 = IOMUX_PIN(60, 16),
+ MX31_PIN_SD1_CLK = IOMUX_PIN(59, 17),
+ MX31_PIN_SD1_CMD = IOMUX_PIN(58, 18),
+ MX31_PIN_D3_SPL = IOMUX_PIN(0xff, 19),
+ MX31_PIN_D3_CLS = IOMUX_PIN(0xff, 20),
+ MX31_PIN_D3_REV = IOMUX_PIN(0xff, 21),
+ MX31_PIN_CONTRAST = IOMUX_PIN(0xff, 22),
+ MX31_PIN_VSYNC3 = IOMUX_PIN(0xff, 23),
+ MX31_PIN_READ = IOMUX_PIN(0xff, 24),
+ MX31_PIN_WRITE = IOMUX_PIN(0xff, 25),
+ MX31_PIN_PAR_RS = IOMUX_PIN(0xff, 26),
+ MX31_PIN_SER_RS = IOMUX_PIN(89, 27),
+ MX31_PIN_LCS1 = IOMUX_PIN(88, 28),
+ MX31_PIN_LCS0 = IOMUX_PIN(87, 29),
+ MX31_PIN_SD_D_CLK = IOMUX_PIN(86, 30),
+ MX31_PIN_SD_D_IO = IOMUX_PIN(85, 31),
+ MX31_PIN_SD_D_I = IOMUX_PIN(84, 32),
+ MX31_PIN_DRDY0 = IOMUX_PIN(0xff, 33),
+ MX31_PIN_FPSHIFT = IOMUX_PIN(0xff, 34),
+ MX31_PIN_HSYNC = IOMUX_PIN(0xff, 35),
+ MX31_PIN_VSYNC0 = IOMUX_PIN(0xff, 36),
+ MX31_PIN_LD17 = IOMUX_PIN(0xff, 37),
+ MX31_PIN_LD16 = IOMUX_PIN(0xff, 38),
+ MX31_PIN_LD15 = IOMUX_PIN(0xff, 39),
+ MX31_PIN_LD14 = IOMUX_PIN(0xff, 40),
+ MX31_PIN_LD13 = IOMUX_PIN(0xff, 41),
+ MX31_PIN_LD12 = IOMUX_PIN(0xff, 42),
+ MX31_PIN_LD11 = IOMUX_PIN(0xff, 43),
+ MX31_PIN_LD10 = IOMUX_PIN(0xff, 44),
+ MX31_PIN_LD9 = IOMUX_PIN(0xff, 45),
+ MX31_PIN_LD8 = IOMUX_PIN(0xff, 46),
+ MX31_PIN_LD7 = IOMUX_PIN(0xff, 47),
+ MX31_PIN_LD6 = IOMUX_PIN(0xff, 48),
+ MX31_PIN_LD5 = IOMUX_PIN(0xff, 49),
+ MX31_PIN_LD4 = IOMUX_PIN(0xff, 50),
+ MX31_PIN_LD3 = IOMUX_PIN(0xff, 51),
+ MX31_PIN_LD2 = IOMUX_PIN(0xff, 52),
+ MX31_PIN_LD1 = IOMUX_PIN(0xff, 53),
+ MX31_PIN_LD0 = IOMUX_PIN(0xff, 54),
+ MX31_PIN_USBH2_DATA1 = IOMUX_PIN(0xff, 55),
+ MX31_PIN_USBH2_DATA0 = IOMUX_PIN(0xff, 56),
+ MX31_PIN_USBH2_NXT = IOMUX_PIN(0xff, 57),
+ MX31_PIN_USBH2_STP = IOMUX_PIN(0xff, 58),
+ MX31_PIN_USBH2_DIR = IOMUX_PIN(0xff, 59),
+ MX31_PIN_USBH2_CLK = IOMUX_PIN(0xff, 60),
+ MX31_PIN_USBOTG_DATA7 = IOMUX_PIN(0xff, 61),
+ MX31_PIN_USBOTG_DATA6 = IOMUX_PIN(0xff, 62),
+ MX31_PIN_USBOTG_DATA5 = IOMUX_PIN(0xff, 63),
+ MX31_PIN_USBOTG_DATA4 = IOMUX_PIN(0xff, 64),
+ MX31_PIN_USBOTG_DATA3 = IOMUX_PIN(0xff, 65),
+ MX31_PIN_USBOTG_DATA2 = IOMUX_PIN(0xff, 66),
+ MX31_PIN_USBOTG_DATA1 = IOMUX_PIN(0xff, 67),
+ MX31_PIN_USBOTG_DATA0 = IOMUX_PIN(0xff, 68),
+ MX31_PIN_USBOTG_NXT = IOMUX_PIN(0xff, 69),
+ MX31_PIN_USBOTG_STP = IOMUX_PIN(0xff, 70),
+ MX31_PIN_USBOTG_DIR = IOMUX_PIN(0xff, 71),
+ MX31_PIN_USBOTG_CLK = IOMUX_PIN(0xff, 72),
+ MX31_PIN_USB_BYP = IOMUX_PIN(31, 73),
+ MX31_PIN_USB_OC = IOMUX_PIN(30, 74),
+ MX31_PIN_USB_PWR = IOMUX_PIN(29, 75),
+ MX31_PIN_SJC_MOD = IOMUX_PIN(0xff, 76),
+ MX31_PIN_DE_B = IOMUX_PIN(0xff, 77),
+ MX31_PIN_TRSTB = IOMUX_PIN(0xff, 78),
+ MX31_PIN_TDO = IOMUX_PIN(0xff, 79),
+ MX31_PIN_TDI = IOMUX_PIN(0xff, 80),
+ MX31_PIN_TMS = IOMUX_PIN(0xff, 81),
+ MX31_PIN_TCK = IOMUX_PIN(0xff, 82),
+ MX31_PIN_RTCK = IOMUX_PIN(0xff, 83),
+ MX31_PIN_KEY_COL7 = IOMUX_PIN(57, 84),
+ MX31_PIN_KEY_COL6 = IOMUX_PIN(56, 85),
+ MX31_PIN_KEY_COL5 = IOMUX_PIN(55, 86),
+ MX31_PIN_KEY_COL4 = IOMUX_PIN(54, 87),
+ MX31_PIN_KEY_COL3 = IOMUX_PIN(0xff, 88),
+ MX31_PIN_KEY_COL2 = IOMUX_PIN(0xff, 89),
+ MX31_PIN_KEY_COL1 = IOMUX_PIN(0xff, 90),
+ MX31_PIN_KEY_COL0 = IOMUX_PIN(0xff, 91),
+ MX31_PIN_KEY_ROW7 = IOMUX_PIN(53, 92),
+ MX31_PIN_KEY_ROW6 = IOMUX_PIN(52, 93),
+ MX31_PIN_KEY_ROW5 = IOMUX_PIN(51, 94),
+ MX31_PIN_KEY_ROW4 = IOMUX_PIN(50, 95),
+ MX31_PIN_KEY_ROW3 = IOMUX_PIN(0xff, 96),
+ MX31_PIN_KEY_ROW2 = IOMUX_PIN(0xff, 97),
+ MX31_PIN_KEY_ROW1 = IOMUX_PIN(0xff, 98),
+ MX31_PIN_KEY_ROW0 = IOMUX_PIN(0xff, 99),
+ MX31_PIN_BATT_LINE = IOMUX_PIN(49, 100),
+ MX31_PIN_CTS2 = IOMUX_PIN(0xff, 101),
+ MX31_PIN_RTS2 = IOMUX_PIN(0xff, 102),
+ MX31_PIN_TXD2 = IOMUX_PIN(28, 103),
+ MX31_PIN_RXD2 = IOMUX_PIN(27, 104),
+ MX31_PIN_DTR_DCE2 = IOMUX_PIN(48, 105),
+ MX31_PIN_DCD_DTE1 = IOMUX_PIN(47, 106),
+ MX31_PIN_RI_DTE1 = IOMUX_PIN(46, 107),
+ MX31_PIN_DSR_DTE1 = IOMUX_PIN(45, 108),
+ MX31_PIN_DTR_DTE1 = IOMUX_PIN(44, 109),
+ MX31_PIN_DCD_DCE1 = IOMUX_PIN(43, 110),
+ MX31_PIN_RI_DCE1 = IOMUX_PIN(42, 111),
+ MX31_PIN_DSR_DCE1 = IOMUX_PIN(41, 112),
+ MX31_PIN_DTR_DCE1 = IOMUX_PIN(40, 113),
+ MX31_PIN_CTS1 = IOMUX_PIN(39, 114),
+ MX31_PIN_RTS1 = IOMUX_PIN(38, 115),
+ MX31_PIN_TXD1 = IOMUX_PIN(37, 116),
+ MX31_PIN_RXD1 = IOMUX_PIN(36, 117),
+ MX31_PIN_CSPI2_SPI_RDY = IOMUX_PIN(0xff, 118),
+ MX31_PIN_CSPI2_SCLK = IOMUX_PIN(0xff, 119),
+ MX31_PIN_CSPI2_SS2 = IOMUX_PIN(0xff, 120),
+ MX31_PIN_CSPI2_SS1 = IOMUX_PIN(0xff, 121),
+ MX31_PIN_CSPI2_SS0 = IOMUX_PIN(0xff, 122),
+ MX31_PIN_CSPI2_MISO = IOMUX_PIN(0xff, 123),
+ MX31_PIN_CSPI2_MOSI = IOMUX_PIN(0xff, 124),
+ MX31_PIN_CSPI1_SPI_RDY = IOMUX_PIN(0xff, 125),
+ MX31_PIN_CSPI1_SCLK = IOMUX_PIN(0xff, 126),
+ MX31_PIN_CSPI1_SS2 = IOMUX_PIN(0xff, 127),
+ MX31_PIN_CSPI1_SS1 = IOMUX_PIN(0xff, 128),
+ MX31_PIN_CSPI1_SS0 = IOMUX_PIN(0xff, 129),
+ MX31_PIN_CSPI1_MISO = IOMUX_PIN(0xff, 130),
+ MX31_PIN_CSPI1_MOSI = IOMUX_PIN(0xff, 131),
+ MX31_PIN_SFS6 = IOMUX_PIN(26, 132),
+ MX31_PIN_SCK6 = IOMUX_PIN(25, 133),
+ MX31_PIN_SRXD6 = IOMUX_PIN(24, 134),
+ MX31_PIN_STXD6 = IOMUX_PIN(23, 135),
+ MX31_PIN_SFS5 = IOMUX_PIN(0xff, 136),
+ MX31_PIN_SCK5 = IOMUX_PIN(0xff, 137),
+ MX31_PIN_SRXD5 = IOMUX_PIN(22, 138),
+ MX31_PIN_STXD5 = IOMUX_PIN(21, 139),
+ MX31_PIN_SFS4 = IOMUX_PIN(0xff, 140),
+ MX31_PIN_SCK4 = IOMUX_PIN(0xff, 141),
+ MX31_PIN_SRXD4 = IOMUX_PIN(20, 142),
+ MX31_PIN_STXD4 = IOMUX_PIN(19, 143),
+ MX31_PIN_SFS3 = IOMUX_PIN(0xff, 144),
+ MX31_PIN_SCK3 = IOMUX_PIN(0xff, 145),
+ MX31_PIN_SRXD3 = IOMUX_PIN(18, 146),
+ MX31_PIN_STXD3 = IOMUX_PIN(17, 147),
+ MX31_PIN_I2C_DAT = IOMUX_PIN(0xff, 148),
+ MX31_PIN_I2C_CLK = IOMUX_PIN(0xff, 149),
+ MX31_PIN_CSI_PIXCLK = IOMUX_PIN(83, 150),
+ MX31_PIN_CSI_HSYNC = IOMUX_PIN(82, 151),
+ MX31_PIN_CSI_VSYNC = IOMUX_PIN(81, 152),
+ MX31_PIN_CSI_MCLK = IOMUX_PIN(80, 153),
+ MX31_PIN_CSI_D15 = IOMUX_PIN(79, 154),
+ MX31_PIN_CSI_D14 = IOMUX_PIN(78, 155),
+ MX31_PIN_CSI_D13 = IOMUX_PIN(77, 156),
+ MX31_PIN_CSI_D12 = IOMUX_PIN(76, 157),
+ MX31_PIN_CSI_D11 = IOMUX_PIN(75, 158),
+ MX31_PIN_CSI_D10 = IOMUX_PIN(74, 159),
+ MX31_PIN_CSI_D9 = IOMUX_PIN(73, 160),
+ MX31_PIN_CSI_D8 = IOMUX_PIN(72, 161),
+ MX31_PIN_CSI_D7 = IOMUX_PIN(71, 162),
+ MX31_PIN_CSI_D6 = IOMUX_PIN(70, 163),
+ MX31_PIN_CSI_D5 = IOMUX_PIN(69, 164),
+ MX31_PIN_CSI_D4 = IOMUX_PIN(68, 165),
+ MX31_PIN_M_GRANT = IOMUX_PIN(0xff, 166),
+ MX31_PIN_M_REQUEST = IOMUX_PIN(0xff, 167),
+ MX31_PIN_PC_POE = IOMUX_PIN(0xff, 168),
+ MX31_PIN_PC_RW_B = IOMUX_PIN(0xff, 169),
+ MX31_PIN_IOIS16 = IOMUX_PIN(0xff, 170),
+ MX31_PIN_PC_RST = IOMUX_PIN(0xff, 171),
+ MX31_PIN_PC_BVD2 = IOMUX_PIN(0xff, 172),
+ MX31_PIN_PC_BVD1 = IOMUX_PIN(0xff, 173),
+ MX31_PIN_PC_VS2 = IOMUX_PIN(0xff, 174),
+ MX31_PIN_PC_VS1 = IOMUX_PIN(0xff, 175),
+ MX31_PIN_PC_PWRON = IOMUX_PIN(0xff, 176),
+ MX31_PIN_PC_READY = IOMUX_PIN(0xff, 177),
+ MX31_PIN_PC_WAIT_B = IOMUX_PIN(0xff, 178),
+ MX31_PIN_PC_CD2_B = IOMUX_PIN(0xff, 179),
+ MX31_PIN_PC_CD1_B = IOMUX_PIN(0xff, 180),
+ MX31_PIN_D0 = IOMUX_PIN(0xff, 181),
+ MX31_PIN_D1 = IOMUX_PIN(0xff, 182),
+ MX31_PIN_D2 = IOMUX_PIN(0xff, 183),
+ MX31_PIN_D3 = IOMUX_PIN(0xff, 184),
+ MX31_PIN_D4 = IOMUX_PIN(0xff, 185),
+ MX31_PIN_D5 = IOMUX_PIN(0xff, 186),
+ MX31_PIN_D6 = IOMUX_PIN(0xff, 187),
+ MX31_PIN_D7 = IOMUX_PIN(0xff, 188),
+ MX31_PIN_D8 = IOMUX_PIN(0xff, 189),
+ MX31_PIN_D9 = IOMUX_PIN(0xff, 190),
+ MX31_PIN_D10 = IOMUX_PIN(0xff, 191),
+ MX31_PIN_D11 = IOMUX_PIN(0xff, 192),
+ MX31_PIN_D12 = IOMUX_PIN(0xff, 193),
+ MX31_PIN_D13 = IOMUX_PIN(0xff, 194),
+ MX31_PIN_D14 = IOMUX_PIN(0xff, 195),
+ MX31_PIN_D15 = IOMUX_PIN(0xff, 196),
+ MX31_PIN_NFRB = IOMUX_PIN(16, 197),
+ MX31_PIN_NFCE_B = IOMUX_PIN(15, 198),
+ MX31_PIN_NFWP_B = IOMUX_PIN(14, 199),
+ MX31_PIN_NFCLE = IOMUX_PIN(13, 200),
+ MX31_PIN_NFALE = IOMUX_PIN(12, 201),
+ MX31_PIN_NFRE_B = IOMUX_PIN(11, 202),
+ MX31_PIN_NFWE_B = IOMUX_PIN(10, 203),
+ MX31_PIN_SDQS3 = IOMUX_PIN(0xff, 204),
+ MX31_PIN_SDQS2 = IOMUX_PIN(0xff, 205),
+ MX31_PIN_SDQS1 = IOMUX_PIN(0xff, 206),
+ MX31_PIN_SDQS0 = IOMUX_PIN(0xff, 207),
+ MX31_PIN_SDCLK_B = IOMUX_PIN(0xff, 208),
+ MX31_PIN_SDCLK = IOMUX_PIN(0xff, 209),
+ MX31_PIN_SDCKE1 = IOMUX_PIN(0xff, 210),
+ MX31_PIN_SDCKE0 = IOMUX_PIN(0xff, 211),
+ MX31_PIN_SDWE = IOMUX_PIN(0xff, 212),
+ MX31_PIN_CAS = IOMUX_PIN(0xff, 213),
+ MX31_PIN_RAS = IOMUX_PIN(0xff, 214),
+ MX31_PIN_RW = IOMUX_PIN(0xff, 215),
+ MX31_PIN_BCLK = IOMUX_PIN(0xff, 216),
+ MX31_PIN_LBA = IOMUX_PIN(0xff, 217),
+ MX31_PIN_ECB = IOMUX_PIN(0xff, 218),
+ MX31_PIN_CS5 = IOMUX_PIN(0xff, 219),
+ MX31_PIN_CS4 = IOMUX_PIN(0xff, 220),
+ MX31_PIN_CS3 = IOMUX_PIN(0xff, 221),
+ MX31_PIN_CS2 = IOMUX_PIN(0xff, 222),
+ MX31_PIN_CS1 = IOMUX_PIN(0xff, 223),
+ MX31_PIN_CS0 = IOMUX_PIN(0xff, 224),
+ MX31_PIN_OE = IOMUX_PIN(0xff, 225),
+ MX31_PIN_EB1 = IOMUX_PIN(0xff, 226),
+ MX31_PIN_EB0 = IOMUX_PIN(0xff, 227),
+ MX31_PIN_DQM3 = IOMUX_PIN(0xff, 228),
+ MX31_PIN_DQM2 = IOMUX_PIN(0xff, 229),
+ MX31_PIN_DQM1 = IOMUX_PIN(0xff, 230),
+ MX31_PIN_DQM0 = IOMUX_PIN(0xff, 231),
+ MX31_PIN_SD31 = IOMUX_PIN(0xff, 232),
+ MX31_PIN_SD30 = IOMUX_PIN(0xff, 233),
+ MX31_PIN_SD29 = IOMUX_PIN(0xff, 234),
+ MX31_PIN_SD28 = IOMUX_PIN(0xff, 235),
+ MX31_PIN_SD27 = IOMUX_PIN(0xff, 236),
+ MX31_PIN_SD26 = IOMUX_PIN(0xff, 237),
+ MX31_PIN_SD25 = IOMUX_PIN(0xff, 238),
+ MX31_PIN_SD24 = IOMUX_PIN(0xff, 239),
+ MX31_PIN_SD23 = IOMUX_PIN(0xff, 240),
+ MX31_PIN_SD22 = IOMUX_PIN(0xff, 241),
+ MX31_PIN_SD21 = IOMUX_PIN(0xff, 242),
+ MX31_PIN_SD20 = IOMUX_PIN(0xff, 243),
+ MX31_PIN_SD19 = IOMUX_PIN(0xff, 244),
+ MX31_PIN_SD18 = IOMUX_PIN(0xff, 245),
+ MX31_PIN_SD17 = IOMUX_PIN(0xff, 246),
+ MX31_PIN_SD16 = IOMUX_PIN(0xff, 247),
+ MX31_PIN_SD15 = IOMUX_PIN(0xff, 248),
+ MX31_PIN_SD14 = IOMUX_PIN(0xff, 249),
+ MX31_PIN_SD13 = IOMUX_PIN(0xff, 250),
+ MX31_PIN_SD12 = IOMUX_PIN(0xff, 251),
+ MX31_PIN_SD11 = IOMUX_PIN(0xff, 252),
+ MX31_PIN_SD10 = IOMUX_PIN(0xff, 253),
+ MX31_PIN_SD9 = IOMUX_PIN(0xff, 254),
+ MX31_PIN_SD8 = IOMUX_PIN(0xff, 255),
+ MX31_PIN_SD7 = IOMUX_PIN(0xff, 256),
+ MX31_PIN_SD6 = IOMUX_PIN(0xff, 257),
+ MX31_PIN_SD5 = IOMUX_PIN(0xff, 258),
+ MX31_PIN_SD4 = IOMUX_PIN(0xff, 259),
+ MX31_PIN_SD3 = IOMUX_PIN(0xff, 260),
+ MX31_PIN_SD2 = IOMUX_PIN(0xff, 261),
+ MX31_PIN_SD1 = IOMUX_PIN(0xff, 262),
+ MX31_PIN_SD0 = IOMUX_PIN(0xff, 263),
+ MX31_PIN_SDBA0 = IOMUX_PIN(0xff, 264),
+ MX31_PIN_SDBA1 = IOMUX_PIN(0xff, 265),
+ MX31_PIN_A25 = IOMUX_PIN(0xff, 266),
+ MX31_PIN_A24 = IOMUX_PIN(0xff, 267),
+ MX31_PIN_A23 = IOMUX_PIN(0xff, 268),
+ MX31_PIN_A22 = IOMUX_PIN(0xff, 269),
+ MX31_PIN_A21 = IOMUX_PIN(0xff, 270),
+ MX31_PIN_A20 = IOMUX_PIN(0xff, 271),
+ MX31_PIN_A19 = IOMUX_PIN(0xff, 272),
+ MX31_PIN_A18 = IOMUX_PIN(0xff, 273),
+ MX31_PIN_A17 = IOMUX_PIN(0xff, 274),
+ MX31_PIN_A16 = IOMUX_PIN(0xff, 275),
+ MX31_PIN_A14 = IOMUX_PIN(0xff, 276),
+ MX31_PIN_A15 = IOMUX_PIN(0xff, 277),
+ MX31_PIN_A13 = IOMUX_PIN(0xff, 278),
+ MX31_PIN_A12 = IOMUX_PIN(0xff, 279),
+ MX31_PIN_A11 = IOMUX_PIN(0xff, 280),
+ MX31_PIN_MA10 = IOMUX_PIN(0xff, 281),
+ MX31_PIN_A10 = IOMUX_PIN(0xff, 282),
+ MX31_PIN_A9 = IOMUX_PIN(0xff, 283),
+ MX31_PIN_A8 = IOMUX_PIN(0xff, 284),
+ MX31_PIN_A7 = IOMUX_PIN(0xff, 285),
+ MX31_PIN_A6 = IOMUX_PIN(0xff, 286),
+ MX31_PIN_A5 = IOMUX_PIN(0xff, 287),
+ MX31_PIN_A4 = IOMUX_PIN(0xff, 288),
+ MX31_PIN_A3 = IOMUX_PIN(0xff, 289),
+ MX31_PIN_A2 = IOMUX_PIN(0xff, 290),
+ MX31_PIN_A1 = IOMUX_PIN(0xff, 291),
+ MX31_PIN_A0 = IOMUX_PIN(0xff, 292),
+ MX31_PIN_VPG1 = IOMUX_PIN(0xff, 293),
+ MX31_PIN_VPG0 = IOMUX_PIN(0xff, 294),
+ MX31_PIN_DVFS1 = IOMUX_PIN(0xff, 295),
+ MX31_PIN_DVFS0 = IOMUX_PIN(0xff, 296),
+ MX31_PIN_VSTBY = IOMUX_PIN(0xff, 297),
+ MX31_PIN_POWER_FAIL = IOMUX_PIN(0xff, 298),
+ MX31_PIN_CKIL = IOMUX_PIN(0xff, 299),
+ MX31_PIN_BOOT_MODE4 = IOMUX_PIN(0xff, 300),
+ MX31_PIN_BOOT_MODE3 = IOMUX_PIN(0xff, 301),
+ MX31_PIN_BOOT_MODE2 = IOMUX_PIN(0xff, 302),
+ MX31_PIN_BOOT_MODE1 = IOMUX_PIN(0xff, 303),
+ MX31_PIN_BOOT_MODE0 = IOMUX_PIN(0xff, 304),
+ MX31_PIN_CLKO = IOMUX_PIN(0xff, 305),
+ MX31_PIN_POR_B = IOMUX_PIN(0xff, 306),
+ MX31_PIN_RESET_IN_B = IOMUX_PIN(0xff, 307),
+ MX31_PIN_CKIH = IOMUX_PIN(0xff, 308),
+ MX31_PIN_SIMPD0 = IOMUX_PIN(35, 309),
+ MX31_PIN_SRX0 = IOMUX_PIN(34, 310),
+ MX31_PIN_STX0 = IOMUX_PIN(33, 311),
+ MX31_PIN_SVEN0 = IOMUX_PIN(32, 312),
+ MX31_PIN_SRST0 = IOMUX_PIN(67, 313),
+ MX31_PIN_SCLK0 = IOMUX_PIN(66, 314),
+ MX31_PIN_GPIO3_1 = IOMUX_PIN(65, 315),
+ MX31_PIN_GPIO3_0 = IOMUX_PIN(64, 316),
+ MX31_PIN_GPIO1_6 = IOMUX_PIN(6, 317),
+ MX31_PIN_GPIO1_5 = IOMUX_PIN(5, 318),
+ MX31_PIN_GPIO1_4 = IOMUX_PIN(4, 319),
+ MX31_PIN_GPIO1_3 = IOMUX_PIN(3, 320),
+ MX31_PIN_GPIO1_2 = IOMUX_PIN(2, 321),
+ MX31_PIN_GPIO1_1 = IOMUX_PIN(1, 322),
+ MX31_PIN_GPIO1_0 = IOMUX_PIN(0, 323),
+ MX31_PIN_PWMO = IOMUX_PIN(9, 324),
+ MX31_PIN_WATCHDOG_RST = IOMUX_PIN(0xff, 325),
+ MX31_PIN_COMPARE = IOMUX_PIN(8, 326),
+ MX31_PIN_CAPTURE = IOMUX_PIN(7, 327),
+};
/* Bit definitions for RCSR register in CCM */
#define CCM_RCSR_NF16B (1 << 31)
@@ -194,6 +558,12 @@ struct gpio_regs {
/* Register offsets based on IOMUXC_BASE */
/* 0x00 .. 0x7b */
+#define MUX_CTL_USBH2_DATA1 0x40
+#define MUX_CTL_USBH2_DIR 0x44
+#define MUX_CTL_USBH2_STP 0x45
+#define MUX_CTL_USBH2_NXT 0x46
+#define MUX_CTL_USBH2_DATA0 0x47
+#define MUX_CTL_USBH2_CLK 0x4B
#define MUX_CTL_RTS1 0x7c
#define MUX_CTL_CTS1 0x7d
#define MUX_CTL_DTR_DCE1 0x7e
@@ -219,6 +589,11 @@ struct gpio_regs {
#define MUX_CTL_SCK6 0x92
#define MUX_CTL_SFS6 0x93
+#define MUX_CTL_STXD3 0x9C
+#define MUX_CTL_SRXD3 0x9D
+#define MUX_CTL_SCK3 0x9E
+#define MUX_CTL_SFS3 0x9F
+
#define MUX_CTL_NFC_WP 0xD0
#define MUX_CTL_NFC_CE 0xD1
#define MUX_CTL_NFC_RB 0xD2
@@ -324,4 +699,33 @@ struct gpio_regs {
#define IRAM_BASE_ADDR 0x1FFFC000
#define IRAM_SIZE (16 * 1024)
+#define MX31_AIPS1_BASE_ADDR 0x43f00000
+#define MX31_OTG_BASE_ADDR (MX31_AIPS1_BASE_ADDR + 0x88000)
+
+/* USB portsc */
+/* values for portsc field */
+#define MXC_EHCI_PHY_LOW_POWER_SUSPEND (1 << 23)
+#define MXC_EHCI_FORCE_FS (1 << 24)
+#define MXC_EHCI_UTMI_8BIT (0 << 28)
+#define MXC_EHCI_UTMI_16BIT (1 << 28)
+#define MXC_EHCI_SERIAL (1 << 29)
+#define MXC_EHCI_MODE_UTMI (0 << 30)
+#define MXC_EHCI_MODE_PHILIPS (1 << 30)
+#define MXC_EHCI_MODE_ULPI (2 << 30)
+#define MXC_EHCI_MODE_SERIAL (3 << 30)
+
+/* values for flags field */
+#define MXC_EHCI_INTERFACE_DIFF_UNI (0 << 0)
+#define MXC_EHCI_INTERFACE_DIFF_BI (1 << 0)
+#define MXC_EHCI_INTERFACE_SINGLE_UNI (2 << 0)
+#define MXC_EHCI_INTERFACE_SINGLE_BI (3 << 0)
+#define MXC_EHCI_INTERFACE_MASK (0xf)
+
+#define MXC_EHCI_POWER_PINS_ENABLED (1 << 5)
+#define MXC_EHCI_TTL_ENABLED (1 << 6)
+
+#define MXC_EHCI_INTERNAL_PHY (1 << 7)
+#define MXC_EHCI_IPPUE_DOWN (1 << 8)
+#define MXC_EHCI_IPPUE_UP (1 << 9)
+
#endif /* __ASM_ARCH_MX31_REGS_H */
diff --git a/drivers/video/mx3fb.c b/drivers/video/mx3fb.c
index 7f04b49..51831f0 100644
--- a/drivers/video/mx3fb.c
+++ b/drivers/video/mx3fb.c
@@ -334,37 +334,6 @@ enum ipu_panel {
#define IOMUX_MODE_L(pin, mode) IOMUX_MODE(((pin) + 0xc) ^ 3, mode)
-enum lcd_pin {
- MX31_PIN_D3_SPL = IOMUX_PIN(0xff, 19),
- MX31_PIN_D3_CLS = IOMUX_PIN(0xff, 20),
- MX31_PIN_D3_REV = IOMUX_PIN(0xff, 21),
- MX31_PIN_CONTRAST = IOMUX_PIN(0xff, 22),
- MX31_PIN_VSYNC3 = IOMUX_PIN(0xff, 23),
-
- MX31_PIN_DRDY0 = IOMUX_PIN(0xff, 33),
- MX31_PIN_FPSHIFT = IOMUX_PIN(0xff, 34),
- MX31_PIN_HSYNC = IOMUX_PIN(0xff, 35),
-
- MX31_PIN_LD17 = IOMUX_PIN(0xff, 37),
- MX31_PIN_LD16 = IOMUX_PIN(0xff, 38),
- MX31_PIN_LD15 = IOMUX_PIN(0xff, 39),
- MX31_PIN_LD14 = IOMUX_PIN(0xff, 40),
- MX31_PIN_LD13 = IOMUX_PIN(0xff, 41),
- MX31_PIN_LD12 = IOMUX_PIN(0xff, 42),
- MX31_PIN_LD11 = IOMUX_PIN(0xff, 43),
- MX31_PIN_LD10 = IOMUX_PIN(0xff, 44),
- MX31_PIN_LD9 = IOMUX_PIN(0xff, 45),
- MX31_PIN_LD8 = IOMUX_PIN(0xff, 46),
- MX31_PIN_LD7 = IOMUX_PIN(0xff, 47),
- MX31_PIN_LD6 = IOMUX_PIN(0xff, 48),
- MX31_PIN_LD5 = IOMUX_PIN(0xff, 49),
- MX31_PIN_LD4 = IOMUX_PIN(0xff, 50),
- MX31_PIN_LD3 = IOMUX_PIN(0xff, 51),
- MX31_PIN_LD2 = IOMUX_PIN(0xff, 52),
- MX31_PIN_LD1 = IOMUX_PIN(0xff, 53),
- MX31_PIN_LD0 = IOMUX_PIN(0xff, 54),
-};
-
struct chan_param_mem_planar {
/* Word 0 */
u32 xv:10;
--
1.6.3.3
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [U-Boot] [PATCH 2/3] MX31: Add support for MXC EHCI controller
2010-10-07 9:27 [U-Boot] [PATCH 1/3] MX31: add support for setting pin pads Stefano Babic
@ 2010-10-07 9:27 ` Stefano Babic
2010-10-07 9:27 ` [U-Boot] [PATCH 3/3] MX31: Add USB Host support to the QONG board Stefano Babic
0 siblings, 1 reply; 6+ messages in thread
From: Stefano Babic @ 2010-10-07 9:27 UTC (permalink / raw)
To: u-boot
The patch adds the EHCI controller for the i.MX31 Soc.
Signed-off-by: Stefano Babic <sbabic@denx.de>
---
drivers/usb/host/Makefile | 1 +
drivers/usb/host/ehci-mxc.c | 130 +++++++++++++++++++++++++++++++++++++++++++
2 files changed, 131 insertions(+), 0 deletions(-)
create mode 100644 drivers/usb/host/ehci-mxc.c
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 255679a..399520e 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -36,6 +36,7 @@ COBJS-$(CONFIG_USB_SL811HS) += sl811-hcd.o
# echi
COBJS-$(CONFIG_USB_EHCI) += ehci-hcd.o
COBJS-$(CONFIG_USB_EHCI_FSL) += ehci-fsl.o
+COBJS-$(CONFIG_USB_EHCI_MXC) += ehci-mxc.o
COBJS-$(CONFIG_USB_EHCI_PPC4XX) += ehci-ppc4xx.o
COBJS-$(CONFIG_USB_EHCI_IXP4XX) += ehci-ixp.o
COBJS-$(CONFIG_USB_EHCI_KIRKWOOD) += ehci-kirkwood.o
diff --git a/drivers/usb/host/ehci-mxc.c b/drivers/usb/host/ehci-mxc.c
new file mode 100644
index 0000000..af8ee90
--- /dev/null
+++ b/drivers/usb/host/ehci-mxc.c
@@ -0,0 +1,130 @@
+/*
+ * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
+ * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software Foundation,
+ * Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+
+#include <common.h>
+#include <usb.h>
+#include <asm/io.h>
+#include <asm/arch/mx31-regs.h>
+#include <usb/ehci-fsl.h>
+#include <errno.h>
+
+#include "ehci.h"
+#include "ehci-core.h"
+
+#define USBCTRL_OTGBASE_OFFSET 0x600
+
+#define MX31_OTG_SIC_SHIFT 29
+#define MX31_OTG_SIC_MASK (0x3 << MX31_OTG_SIC_SHIFT)
+#define MX31_OTG_PM_BIT (1 << 24)
+
+#define MX31_H2_SIC_SHIFT 21
+#define MX31_H2_SIC_MASK (0x3 << MX31_H2_SIC_SHIFT)
+#define MX31_H2_PM_BIT (1 << 16)
+#define MX31_H2_DT_BIT (1 << 5)
+
+#define MX31_H1_SIC_SHIFT 13
+#define MX31_H1_SIC_MASK (0x3 << MX31_H1_SIC_SHIFT)
+#define MX31_H1_PM_BIT (1 << 8)
+#define MX31_H1_DT_BIT (1 << 4)
+
+static int mxc_set_usbcontrol(int port, unsigned int flags)
+{
+ unsigned int v;
+#ifdef CONFIG_MX31
+ v = readl(MX31_OTG_BASE_ADDR + USBCTRL_OTGBASE_OFFSET);
+
+ switch (port) {
+ case 0: /* OTG port */
+ v &= ~(MX31_OTG_SIC_MASK | MX31_OTG_PM_BIT);
+ v |= (flags & MXC_EHCI_INTERFACE_MASK)
+ << MX31_OTG_SIC_SHIFT;
+ if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
+ v |= MX31_OTG_PM_BIT;
+
+ break;
+ case 1: /* H1 port */
+ v &= ~(MX31_H1_SIC_MASK | MX31_H1_PM_BIT |
+ MX31_H1_DT_BIT);
+ v |= (flags & MXC_EHCI_INTERFACE_MASK)
+ << MX31_H1_SIC_SHIFT;
+ if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
+ v |= MX31_H1_PM_BIT;
+
+ if (!(flags & MXC_EHCI_TTL_ENABLED))
+ v |= MX31_H1_DT_BIT;
+
+ break;
+ case 2: /* H2 port */
+ v &= ~(MX31_H2_SIC_MASK | MX31_H2_PM_BIT |
+ MX31_H2_DT_BIT);
+ v |= (flags & MXC_EHCI_INTERFACE_MASK)
+ << MX31_H2_SIC_SHIFT;
+ if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
+ v |= MX31_H2_PM_BIT;
+
+ if (!(flags & MXC_EHCI_TTL_ENABLED))
+ v |= MX31_H2_DT_BIT;
+
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ writel(v, MX31_OTG_BASE_ADDR +
+ USBCTRL_OTGBASE_OFFSET);
+#endif
+ return 0;
+}
+
+int ehci_hcd_init(void)
+{
+ u32 tmp;
+ struct usb_ehci *ehci;
+ struct clock_control_regs *sc_regs =
+ (struct clock_control_regs *)CCM_BASE;
+
+ tmp = __raw_readl(&sc_regs->ccmr);
+ __raw_writel(__raw_readl(&sc_regs->ccmr) | (1 << 9), &sc_regs->ccmr) ;
+
+ udelay(80);
+
+ /* Take USB2 */
+ ehci = (struct usb_ehci *)(MX31_OTG_BASE_ADDR +
+ (0x200 * CONFIG_MXC_USB_PORT));
+ hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
+ hcor = (struct ehci_hcor *)((uint32_t) hccr +
+ HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
+ setbits_le32(&ehci->usbmode, CM_HOST);
+ setbits_le32(&ehci->control, USB_EN);
+
+ __raw_writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc);
+
+ mxc_set_usbcontrol(CONFIG_MXC_USB_PORT, CONFIG_MXC_USB_FLAGS);
+
+ return 0;
+}
+
+/*
+ * Destroy the appropriate control structures corresponding
+ * the the EHCI host controller.
+ */
+int ehci_hcd_stop(void)
+{
+ return 0;
+}
--
1.6.3.3
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [U-Boot] [PATCH 3/3] MX31: Add USB Host support to the QONG board
2010-10-07 9:27 ` [U-Boot] [PATCH 2/3] MX31: Add support for MXC EHCI controller Stefano Babic
@ 2010-10-07 9:27 ` Stefano Babic
2010-10-11 8:17 ` Wolfgang Denk
0 siblings, 1 reply; 6+ messages in thread
From: Stefano Babic @ 2010-10-07 9:27 UTC (permalink / raw)
To: u-boot
Signed-off-by: Stefano Babic <sbabic@denx.de>
---
board/davedenx/qong/qong.c | 33 +++++++++++++++++++++++++++++++++
include/configs/qong.h | 18 +++++++++++++++++-
2 files changed, 50 insertions(+), 1 deletions(-)
diff --git a/board/davedenx/qong/qong.c b/board/davedenx/qong/qong.c
index efeb0bb..8a81cfc 100644
--- a/board/davedenx/qong/qong.c
+++ b/board/davedenx/qong/qong.c
@@ -25,6 +25,7 @@
#include <netdev.h>
#include <asm/arch/mx31.h>
#include <asm/arch/mx31-regs.h>
+#include <asm/io.h>
#include <nand.h>
#include <fsl_pmic.h>
#include <mxc_gpio.h>
@@ -97,6 +98,38 @@ int board_early_init_f (void)
mx31_gpio_mux(MUX_CSPI2_SCLK__CSPI2_CLK);
mx31_gpio_mux(MUX_CSPI2_SPI_RDY__CSPI2_DATAREADY_B);
+ /* Setup pins for USB2 Host */
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_CLK, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_DIR, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_NXT, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_STP, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_DATA0, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_DATA1, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_STXD3, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SRXD3, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SCK3, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SFS3, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_STXD6, MUX_CTL_FUNC));
+ mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SRXD6, MUX_CTL_FUNC));
+
+#define H2_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
+ PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
+
+ mx31_set_pad(MX31_PIN_USBH2_CLK, H2_PAD_CFG);
+ mx31_set_pad(MX31_PIN_USBH2_DIR, H2_PAD_CFG);
+ mx31_set_pad(MX31_PIN_USBH2_NXT, H2_PAD_CFG);
+ mx31_set_pad(MX31_PIN_USBH2_STP, H2_PAD_CFG);
+ mx31_set_pad(MX31_PIN_USBH2_DATA0, H2_PAD_CFG); /* USBH2_DATA0 */
+ mx31_set_pad(MX31_PIN_USBH2_DATA1, H2_PAD_CFG); /* USBH2_DATA1 */
+ mx31_set_pad(MX31_PIN_SRXD6, H2_PAD_CFG); /* USBH2_DATA2 */
+ mx31_set_pad(MX31_PIN_STXD6, H2_PAD_CFG); /* USBH2_DATA3 */
+ mx31_set_pad(MX31_PIN_SFS3, H2_PAD_CFG); /* USBH2_DATA4 */
+ mx31_set_pad(MX31_PIN_SCK3, H2_PAD_CFG); /* USBH2_DATA5 */
+ mx31_set_pad(MX31_PIN_SRXD3, H2_PAD_CFG); /* USBH2_DATA6 */
+ mx31_set_pad(MX31_PIN_STXD3, H2_PAD_CFG); /* USBH2_DATA7 */
+
+ writel(readl((IOMUXC_BASE + 0x8)) | (1 << 11), IOMUXC_BASE + 0x8);
+
return 0;
}
diff --git a/include/configs/qong.h b/include/configs/qong.h
index 2d124ea..fef8094 100644
--- a/include/configs/qong.h
+++ b/include/configs/qong.h
@@ -89,6 +89,22 @@
#define CONFIG_BMP_16BPP
#define CONFIG_DISPLAY_COM57H5M10XRC
+/* USB */
+#define CONFIG_CMD_USB
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_MXC
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORT 2
+#define CONFIG_MXC_USB_PORTSC (MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT)
+#define CONFIG_MXC_USB_FLAGS MXC_EHCI_POWER_PINS_ENABLED
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#define CONFIG_CMD_FAT
+#endif /* CONFIG_CMD_USB */
+
/*
* Reducing the ARP timeout from default 5 seconds to 200ms we speed up the
* initial TFTP transfer, should the user wish one, significantly.
@@ -250,7 +266,7 @@ extern int qong_nand_rdy(void *chip);
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_SECT_SIZE 0x20000
#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x60000)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x80000)
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
--
1.6.3.3
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [U-Boot] [PATCH 3/3] MX31: Add USB Host support to the QONG board
2010-10-07 9:27 ` [U-Boot] [PATCH 3/3] MX31: Add USB Host support to the QONG board Stefano Babic
@ 2010-10-11 8:17 ` Wolfgang Denk
2010-10-13 10:05 ` Remy Bohmer
0 siblings, 1 reply; 6+ messages in thread
From: Wolfgang Denk @ 2010-10-11 8:17 UTC (permalink / raw)
To: u-boot
Dear Remy,
In message <1286443640-29526-3-git-send-email-sbabic@denx.de> you wrote:
> Signed-off-by: Stefano Babic <sbabic@denx.de>
> ---
> board/davedenx/qong/qong.c | 33 +++++++++++++++++++++++++++++++++
> include/configs/qong.h | 18 +++++++++++++++++-
> 2 files changed, 50 insertions(+), 1 deletions(-)
even though USB related, this looks like a board specific patch to me.
Is it OK with you that Stefano pulls this through the iMX repository?
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
A conservative is a man who believes that nothing should be done for
the first time. - Alfred E. Wiggam
^ permalink raw reply [flat|nested] 6+ messages in thread
* [U-Boot] [PATCH 3/3] MX31: Add USB Host support to the QONG board
2010-10-11 8:17 ` Wolfgang Denk
@ 2010-10-13 10:05 ` Remy Bohmer
2010-10-13 10:13 ` Stefano Babic
0 siblings, 1 reply; 6+ messages in thread
From: Remy Bohmer @ 2010-10-13 10:05 UTC (permalink / raw)
To: u-boot
Hi,
2010/10/11 Wolfgang Denk <wd@denx.de>:
> Dear Remy,
>
> In message <1286443640-29526-3-git-send-email-sbabic@denx.de> you wrote:
>> Signed-off-by: Stefano Babic <sbabic@denx.de>
>> ---
>> ?board/davedenx/qong/qong.c | ? 33 +++++++++++++++++++++++++++++++++
>> ?include/configs/qong.h ? ? | ? 18 +++++++++++++++++-
>> ?2 files changed, 50 insertions(+), 1 deletions(-)
>
> even though USB related, this looks like a board specific patch to me.
> Is it OK with you that Stefano pulls this through the iMX repository?
>
OK with me.
Remy
^ permalink raw reply [flat|nested] 6+ messages in thread
* [U-Boot] [PATCH 3/3] MX31: Add USB Host support to the QONG board
2010-10-13 10:05 ` Remy Bohmer
@ 2010-10-13 10:13 ` Stefano Babic
0 siblings, 0 replies; 6+ messages in thread
From: Stefano Babic @ 2010-10-13 10:13 UTC (permalink / raw)
To: u-boot
On 10/13/2010 12:05 PM, Remy Bohmer wrote:
>> even though USB related, this looks like a board specific patch to me.
>> Is it OK with you that Stefano pulls this through the iMX repository?
>>
>
> OK with me.
>
Hi Remy,
thanks - I will merge in u-boot-imx and sent the pull request to Wolfgang
Stefano
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2010-10-13 10:13 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2010-10-07 9:27 [U-Boot] [PATCH 1/3] MX31: add support for setting pin pads Stefano Babic
2010-10-07 9:27 ` [U-Boot] [PATCH 2/3] MX31: Add support for MXC EHCI controller Stefano Babic
2010-10-07 9:27 ` [U-Boot] [PATCH 3/3] MX31: Add USB Host support to the QONG board Stefano Babic
2010-10-11 8:17 ` Wolfgang Denk
2010-10-13 10:05 ` Remy Bohmer
2010-10-13 10:13 ` Stefano Babic
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox