[U-Boot] [PATCH] DaVinci DM6446: Config Update

[U-Boot] [PATCH] DaVinci DM6446: Config Update

[s-paulraj at ti.com]

From: Sandeep Paulraj <s-paulraj@ti.com>

The DM6446 does not build due to the ARM
relocation patch.

Also the board does not build in the NOR
mode. Changed default to NAND to ensure
no build failure.
While at it removed CONFIG_CMD_KGDB

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
---
 include/configs/davinci_dvevm.h |   19 +++++++++++--------
 1 files changed, 11 insertions(+), 8 deletions(-)

diff --git a/include/configs/davinci_dvevm.h b/include/configs/davinci_dvevm.h
index e1b1db1..45214fa 100644
--- a/include/configs/davinci_dvevm.h
+++ b/include/configs/davinci_dvevm.h
@@ -50,7 +50,7 @@
 /*=======*/
 #define DV_EVM
 #define CONFIG_SYS_NAND_SMALLPAGE
-#define CONFIG_SYS_USE_NOR
+#define CONFIG_SYS_USE_NAND
 #define CONFIG_DISPLAY_CPUINFO
 /*===================*/
 /* SoC Configuration */
@@ -78,6 +78,7 @@
 #define CONFIG_STACKSIZE	(256*1024)	/* regular stack */
 #define PHYS_SDRAM_1		0x80000000	/* DDR Start */
 #define PHYS_SDRAM_1_SIZE	0x10000000	/* DDR size 256MB */
+
 #define DDR_8BANKS				/* 8-bank DDR2 (256MB) */
 /*====================*/
 /* Serial Driver info */
@@ -228,11 +229,13 @@
 #define CONFIG_PREBOOT "usb start"
 #endif
 #endif
-/*=======================*/
-/* KGDB support (if any) */
-/*=======================*/
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	1	/* which serial port to use */
-#endif
+
+#define CONFIG_MAX_RAM_BANK_SIZE	(256 << 20)	/* 256 MB */
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_SIZE	0x1000
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + \
+					 CONFIG_SYS_INIT_RAM_SIZE - \
+					 GENERATED_GBL_DATA_SIZE)
+
 #endif /* __CONFIG_H */
-- 
1.6.0.4

[U-Boot] [PATCH] DaVinci DM6446: Config Update

[Albert ARIBAUD]

Hi Sandeep,

Le 03/12/2010 16:37, s-paulraj at ti.com a ?crit :
> From: Sandeep Paulraj<s-paulraj@ti.com>
>
> The DM6446 does not build due to the ARM
> relocation patch.
>
> Also the board does not build in the NOR
> mode. Changed default to NAND to ensure
> no build failure.

What exactly is the build error message in NOR mode?

Amicalement,
-- 
Albert.

[U-Boot] [PATCH] DaVinci DM6446: Config Update

[Paulraj, Sandeep]

Albert,


> 
> From: Sandeep Paulraj <s-paulraj@ti.com>
> 
> The DM6446 does not build due to the ARM
> relocation patch.
> 
> Also the board does not build in the NOR
> mode. Changed default to NAND to ensure
> no build failure.

In the NOR mode, the build complained about a CONFIG variable not being defined for the NOR. I have fixed that as well. I cannot test that yet.
That will probably be a follow up patch.


> While at it removed CONFIG_CMD_KGDB
> 
> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

--Sandeep