* [U-Boot] [STATUS] v2010.12-rc2 released
@ 2010-12-02 21:41 Carlo Caione
2010-12-03 4:40 ` Prafulla Wadaskar
0 siblings, 1 reply; 8+ messages in thread
From: Carlo Caione @ 2010-12-02 21:41 UTC (permalink / raw)
To: u-boot
> Some of the times, the boot hung after printing DRAM: 128 MiB,
> but never did it hang without printing anything.
The same here.
Beagleboard xM rev.A hangs after DRAM: 256 MiB
Regards,
--
Carlo Caione
^ permalink raw reply [flat|nested] 8+ messages in thread* [U-Boot] [STATUS] v2010.12-rc2 released 2010-12-02 21:41 [U-Boot] [STATUS] v2010.12-rc2 released Carlo Caione @ 2010-12-03 4:40 ` Prafulla Wadaskar 2010-12-03 21:11 ` Carlo Caione 0 siblings, 1 reply; 8+ messages in thread From: Prafulla Wadaskar @ 2010-12-03 4:40 UTC (permalink / raw) To: u-boot > -----Original Message----- > From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] > On Behalf Of Carlo Caione > Sent: Friday, December 03, 2010 3:11 AM > To: U-Boot at lists.denx.de > Subject: Re: [U-Boot] [STATUS] v2010.12-rc2 released > > > Some of the times, the boot hung after printing DRAM: 128 MiB, > > but never did it hang without printing anything. > > The same here. > Beagleboard xM rev.A hangs after DRAM: 256 MiB For fix this, needs to change global variables in timer.c REF: http://lists.denx.de/pipermail/u-boot/2010-December/082834.html Regards.. Prafulla .. ^ permalink raw reply [flat|nested] 8+ messages in thread
* [U-Boot] [STATUS] v2010.12-rc2 released 2010-12-03 4:40 ` Prafulla Wadaskar @ 2010-12-03 21:11 ` Carlo Caione 2010-12-04 6:51 ` [U-Boot] OMAP: Hang after memory init, was: " Dirk Behme 0 siblings, 1 reply; 8+ messages in thread From: Carlo Caione @ 2010-12-03 21:11 UTC (permalink / raw) To: u-boot On Thu, 2010-12-02 at 20:40 -0800, Prafulla Wadaskar wrote: > > > -----Original Message----- > > From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] > > On Behalf Of Carlo Caione > > Sent: Friday, December 03, 2010 3:11 AM > > To: U-Boot at lists.denx.de > > Subject: Re: [U-Boot] [STATUS] v2010.12-rc2 released > > > > > Some of the times, the boot hung after printing DRAM: 128 MiB, > > > but never did it hang without printing anything. > > > > The same here. > > Beagleboard xM rev.A hangs after DRAM: 256 MiB > > For fix this, needs to change global variables in timer.c > REF: http://lists.denx.de/pipermail/u-boot/2010-December/082834.html Applied but nothing is changed: Texas Instruments X-Loader 1.4.4ss (Dec 2 2010 - 21:40:58) Beagle xM Rev A Reading boot sector Loading u-boot.bin from mmc U-Boot 2010.12-rc2-00029-g49733aa-dirty (Dec 03 2010 - 22:05:44) OMAP3630/3730-GP ES1.0, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz OMAP3 Beagle board + LPDDR/NAND I2C: ready DRAM: 512 MiB Regards, -- Carlo Caione ^ permalink raw reply [flat|nested] 8+ messages in thread
* [U-Boot] OMAP: Hang after memory init, was: [STATUS] v2010.12-rc2 released 2010-12-03 21:11 ` Carlo Caione @ 2010-12-04 6:51 ` Dirk Behme 2010-12-04 8:07 ` Albert ARIBAUD 0 siblings, 1 reply; 8+ messages in thread From: Dirk Behme @ 2010-12-04 6:51 UTC (permalink / raw) To: u-boot On 03.12.2010 22:11, Carlo Caione wrote: > On Thu, 2010-12-02 at 20:40 -0800, Prafulla Wadaskar wrote: >> >>> -----Original Message----- >>> From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] >>> On Behalf Of Carlo Caione >>> Sent: Friday, December 03, 2010 3:11 AM >>> To: U-Boot at lists.denx.de >>> Subject: Re: [U-Boot] [STATUS] v2010.12-rc2 released >>> >>>> Some of the times, the boot hung after printing DRAM: 128 MiB, >>>> but never did it hang without printing anything. >>> >>> The same here. >>> Beagleboard xM rev.A hangs after DRAM: 256 MiB >> >> For fix this, needs to change global variables in timer.c >> REF: http://lists.denx.de/pipermail/u-boot/2010-December/082834.html > > Applied but nothing is changed: > > Texas Instruments X-Loader 1.4.4ss (Dec 2 2010 - 21:40:58) > Beagle xM Rev A > Reading boot sector > Loading u-boot.bin from mmc > > > U-Boot 2010.12-rc2-00029-g49733aa-dirty (Dec 03 2010 - 22:05:44) > > OMAP3630/3730-GP ES1.0, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz > OMAP3 Beagle board + LPDDR/NAND > I2C: ready > DRAM: 512 MiB I'm not totally sure, so sorry if I'm wrong. But: I understood the link given by Prafulla above only as a reference what has to be done to fix the OMAP hang. I don't think the given patch fixes the issue itself. Most probably we additionally need something like http://lists.denx.de/pipermail/u-boot/2010-December/082965.html for OMAP, too? Best regards Dirk ^ permalink raw reply [flat|nested] 8+ messages in thread
* [U-Boot] OMAP: Hang after memory init, was: [STATUS] v2010.12-rc2 released 2010-12-04 6:51 ` [U-Boot] OMAP: Hang after memory init, was: " Dirk Behme @ 2010-12-04 8:07 ` Albert ARIBAUD 2010-12-04 9:33 ` [U-Boot] OMAP: Hang after memory init Dirk Behme 0 siblings, 1 reply; 8+ messages in thread From: Albert ARIBAUD @ 2010-12-04 8:07 UTC (permalink / raw) To: u-boot Le 04/12/2010 07:51, Dirk Behme a ?crit : > On 03.12.2010 22:11, Carlo Caione wrote: >> On Thu, 2010-12-02 at 20:40 -0800, Prafulla Wadaskar wrote: >>> >>>> -----Original Message----- >>>> From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] >>>> On Behalf Of Carlo Caione >>>> Sent: Friday, December 03, 2010 3:11 AM >>>> To: U-Boot at lists.denx.de >>>> Subject: Re: [U-Boot] [STATUS] v2010.12-rc2 released >>>> >>>>> Some of the times, the boot hung after printing DRAM: 128 MiB, >>>>> but never did it hang without printing anything. >>>> >>>> The same here. >>>> Beagleboard xM rev.A hangs after DRAM: 256 MiB >>> >>> For fix this, needs to change global variables in timer.c >>> REF: http://lists.denx.de/pipermail/u-boot/2010-December/082834.html >> >> Applied but nothing is changed: >> >> Texas Instruments X-Loader 1.4.4ss (Dec 2 2010 - 21:40:58) >> Beagle xM Rev A >> Reading boot sector >> Loading u-boot.bin from mmc >> >> >> U-Boot 2010.12-rc2-00029-g49733aa-dirty (Dec 03 2010 - 22:05:44) >> >> OMAP3630/3730-GP ES1.0, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz >> OMAP3 Beagle board + LPDDR/NAND >> I2C: ready >> DRAM: 512 MiB > > I'm not totally sure, so sorry if I'm wrong. But: > > I understood the link given by Prafulla above only as a reference what > has to be done to fix the OMAP hang. I don't think the given patch > fixes the issue itself. Most probably we additionally need something like > > http://lists.denx.de/pipermail/u-boot/2010-December/082965.html > > for OMAP, too? Also make sure that the r8 register is not trashed by the relocation code in the start.S used for this board. See Andreas' patch for that. > Best regards > > Dirk Amicalement, -- Albert. ^ permalink raw reply [flat|nested] 8+ messages in thread
* [U-Boot] OMAP: Hang after memory init 2010-12-04 8:07 ` Albert ARIBAUD @ 2010-12-04 9:33 ` Dirk Behme 2010-12-04 10:48 ` Albert ARIBAUD 0 siblings, 1 reply; 8+ messages in thread From: Dirk Behme @ 2010-12-04 9:33 UTC (permalink / raw) To: u-boot On 04.12.2010 09:07, Albert ARIBAUD wrote: > Le 04/12/2010 07:51, Dirk Behme a ?crit : >> On 03.12.2010 22:11, Carlo Caione wrote: >>> On Thu, 2010-12-02 at 20:40 -0800, Prafulla Wadaskar wrote: >>>> >>>>> -----Original Message----- >>>>> From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] >>>>> On Behalf Of Carlo Caione >>>>> Sent: Friday, December 03, 2010 3:11 AM >>>>> To: U-Boot at lists.denx.de >>>>> Subject: Re: [U-Boot] [STATUS] v2010.12-rc2 released >>>>> >>>>>> Some of the times, the boot hung after printing DRAM: 128 MiB, >>>>>> but never did it hang without printing anything. >>>>> >>>>> The same here. >>>>> Beagleboard xM rev.A hangs after DRAM: 256 MiB >>>> >>>> For fix this, needs to change global variables in timer.c >>>> REF: http://lists.denx.de/pipermail/u-boot/2010-December/082834.html >>> >>> Applied but nothing is changed: >>> >>> Texas Instruments X-Loader 1.4.4ss (Dec 2 2010 - 21:40:58) >>> Beagle xM Rev A >>> Reading boot sector >>> Loading u-boot.bin from mmc >>> >>> >>> U-Boot 2010.12-rc2-00029-g49733aa-dirty (Dec 03 2010 - 22:05:44) >>> >>> OMAP3630/3730-GP ES1.0, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz >>> OMAP3 Beagle board + LPDDR/NAND >>> I2C: ready >>> DRAM: 512 MiB >> >> I'm not totally sure, so sorry if I'm wrong. But: >> >> I understood the link given by Prafulla above only as a reference what >> has to be done to fix the OMAP hang. I don't think the given patch >> fixes the issue itself. Most probably we additionally need something like >> >> http://lists.denx.de/pipermail/u-boot/2010-December/082965.html >> >> for OMAP, too? > > Also make sure that the r8 register is not trashed by the relocation > code in the start.S used for this board. See Andreas' patch for that. Thanks for the hint! Most probably you mean http://lists.denx.de/pipermail/u-boot/2010-December/082807.html ? This does mean that for Beagle we need at least http://lists.denx.de/pipermail/u-boot/2010-December/082806.html http://lists.denx.de/pipermail/u-boot/2010-December/082805.html http://lists.denx.de/pipermail/u-boot/2010-December/082807.html http://lists.denx.de/pipermail/u-boot/2010-December/082808.html http://lists.denx.de/pipermail/u-boot/2010-December/082834.html plus something like http://lists.denx.de/pipermail/u-boot/2010-December/082965.html for OMAP (still to be written)? Thanks Dirk ^ permalink raw reply [flat|nested] 8+ messages in thread
* [U-Boot] OMAP: Hang after memory init 2010-12-04 9:33 ` [U-Boot] OMAP: Hang after memory init Dirk Behme @ 2010-12-04 10:48 ` Albert ARIBAUD 2010-12-09 16:36 ` Dirk Behme 0 siblings, 1 reply; 8+ messages in thread From: Albert ARIBAUD @ 2010-12-04 10:48 UTC (permalink / raw) To: u-boot Le 04/12/2010 10:33, Dirk Behme a ?crit : >> Also make sure that the r8 register is not trashed by the relocation >> code in the start.S used for this board. See Andreas' patch for that. > > Thanks for the hint! Most probably you mean > > http://lists.denx.de/pipermail/u-boot/2010-December/082807.html > > ? Yes. > This does mean that for Beagle we need at least > > http://lists.denx.de/pipermail/u-boot/2010-December/082806.html > http://lists.denx.de/pipermail/u-boot/2010-December/082805.html > http://lists.denx.de/pipermail/u-boot/2010-December/082807.html > http://lists.denx.de/pipermail/u-boot/2010-December/082808.html > http://lists.denx.de/pipermail/u-boot/2010-December/082834.html Yes - note that ...806 and ...805 are useful but not required to get the board working, IIUC. > plus something like > > http://lists.denx.de/pipermail/u-boot/2010-December/082965.html > > for OMAP (still to be written)? Yes. > Thanks > > Dirk Amicalement, -- Albert. ^ permalink raw reply [flat|nested] 8+ messages in thread
* [U-Boot] OMAP: Hang after memory init 2010-12-04 10:48 ` Albert ARIBAUD @ 2010-12-09 16:36 ` Dirk Behme 0 siblings, 0 replies; 8+ messages in thread From: Dirk Behme @ 2010-12-09 16:36 UTC (permalink / raw) To: u-boot On 04.12.2010 11:48, Albert ARIBAUD wrote: > Le 04/12/2010 10:33, Dirk Behme a ?crit : > >>> Also make sure that the r8 register is not trashed by the relocation >>> code in the start.S used for this board. See Andreas' patch for that. >> >> Thanks for the hint! Most probably you mean >> >> http://lists.denx.de/pipermail/u-boot/2010-December/082807.html >> >> ? > > Yes. > >> This does mean that for Beagle we need at least >> >> http://lists.denx.de/pipermail/u-boot/2010-December/082806.html >> http://lists.denx.de/pipermail/u-boot/2010-December/082805.html >> http://lists.denx.de/pipermail/u-boot/2010-December/082807.html >> http://lists.denx.de/pipermail/u-boot/2010-December/082808.html >> http://lists.denx.de/pipermail/u-boot/2010-December/082834.html > > Yes - note that ...806 and ...805 are useful but not required to get > the board working, IIUC. After all above patches are in mainline now ... >> plus something like >> >> http://lists.denx.de/pipermail/u-boot/2010-December/082965.html >> >> for OMAP (still to be written)? ... does anybody like to test http://lists.denx.de/pipermail/u-boot/2010-December/083449.html on top of recent U-Boot master? Does this fix the OMAP hang? Thanks Dirk ^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2010-12-09 16:36 UTC | newest] Thread overview: 8+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2010-12-02 21:41 [U-Boot] [STATUS] v2010.12-rc2 released Carlo Caione 2010-12-03 4:40 ` Prafulla Wadaskar 2010-12-03 21:11 ` Carlo Caione 2010-12-04 6:51 ` [U-Boot] OMAP: Hang after memory init, was: " Dirk Behme 2010-12-04 8:07 ` Albert ARIBAUD 2010-12-04 9:33 ` [U-Boot] OMAP: Hang after memory init Dirk Behme 2010-12-04 10:48 ` Albert ARIBAUD 2010-12-09 16:36 ` Dirk Behme
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox