[U-Boot] [PATCH 2/2] at91: fixed 'esd gmbh' meesc and otc570 boards

[Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>]

Reinhard Meyer wrote:
> Dear Daniel Gorsulowski,
>> Signed-off-by: Daniel Gorsulowski<Daniel.Gorsulowski@esd.eu>
>> ...
>> -	gd->bd->bi_dram[0].start = PHYS_SDRAM;
>> -	gd->bd->bi_dram[0].size = get_ram_size((long *) PHYS_SDRAM, (1<<  27));
>> +	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
>> +	gd->bd->bi_dram[0].size = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE,
>> +					(1<<  27));
> Maybe there is a suitable SIZE_128MIB (didn't check) - would look more readable ;)

AFAIK, Wolfgang wants to get rid of the sizes.h file. So I'll replace
that with something like (128*1024*1024)

>> diff --git a/board/esd/otc570/otc570.c b/board/esd/otc570/otc570.c
>> index 410d8b4..c66f99e 100644
>> --- a/board/esd/otc570/otc570.c
>> +++ b/board/esd/otc570/otc570.c
>> @@ -1,5 +1,5 @@
>>   /*
>> - * (C) Copyright 2010
>> + * (C) Copyright 2010-2011
>>    * Daniel Gorsulowski<daniel.gorsulowski@esd.eu>
>>    * esd electronic system design gmbh<www.esd.eu>
>>    *
>> @@ -27,6 +27,7 @@
>>    */
>>
>>   #include<common.h>
>> +#include<asm/io.h>
>>   #include<asm/arch/at91sam9263.h>
> including hardware.h does include above, don't include it directly.

Ok, I'll remove this include

...
>> diff --git a/boards.cfg b/boards.cfg
>> index 9b15026..77f3fc4 100644
>> --- a/boards.cfg
>> +++ b/boards.cfg
>> @@ -83,8 +83,10 @@ at91sam9xeek_dataflash_cs0   arm         arm926ejs   at91sam9260ek       atmel
>>   at91sam9xeek_dataflash_cs1   arm         arm926ejs   at91sam9260ek       atmel          at91        at91sam9260ek:AT91SAM9XE,SYS_USE_DATAFLASH_CS1
>>   top9000eval_xe               arm         arm926ejs   top9000             emk            at91        top9000:EVAL9000
>>   top9000su_xe                 arm         arm926ejs   top9000             emk            at91        top9000:SU9000
>> -meesc                        arm         arm926ejs   -                   esd            at91
>> -otc570                       arm         arm926ejs   -                   esd            at91
>> +meesc                        arm         arm926ejs   meesc               esd            at91        meesc:AT91SAM9263,SYS_USE_NANDFLASH
>> +meesc_dataflash              arm         arm926ejs   meesc               esd            at91        meesc:AT91SAM9263,SYS_USE_DATAFLASH
>> +otc570                       arm         arm926ejs   otc570              esd            at91        otc570:AT91SAM9263,SYS_USE_NANDFLASH
>> +otc570_dataflash             arm         arm926ejs   otc570              esd            at91        otc570:AT91SAM9263,SYS_USE_DATAFLASH
> Apparently its always a sam9263, so please don't define it here. The defines in boards.cfg should only be used
> for differences between variants.

I'll move that to board config files

>> diff --git a/include/configs/meesc.h b/include/configs/meesc.h
>> index a27b36b..dbb97ed 100644
>> --- a/include/configs/meesc.h
>> +++ b/include/configs/meesc.h
>> @@ -3,7 +3,7 @@
>>    * Stelian Pop<stelian.pop@leadtechdesign.com>
>>    * Lead Tech Design<www.leadtechdesign.com>
>>    *
>> - * (C) Copyright 2009-2010
>> + * (C) Copyright 2009-2011
>>    * Daniel Gorsulowski<daniel.gorsulowski@esd.eu>
>>    * esd electronic system design gmbh<www.esd.eu>
>>    *
>> @@ -31,49 +31,67 @@
>>   #ifndef __CONFIG_H
>>   #define __CONFIG_H
>>
>> -/* Common stuff */
>> -#define CONFIG_MEESC			1	/* Board is esd MEESC */
>> -#define CONFIG_ARM926EJS		1	/* This is an ARM926EJS Core */
>> -#define CONFIG_AT91SAM9263		1	/* It's an AT91SAM9263 SoC */
>> -#define CONFIG_SYS_AT91_MAIN_CLOCK	16000000/* 16.0 MHz crystal */
>> +/*
>> + * SoC must be defined first, before hardware.h is included.
>> + * In this case SoC is defined in boards.cfg.
> Please define SoC here.

See beyond...

...
> 
> I'll run it through checkpatch.pl later.
> 
> Best Regards,
> Reinhard

Best regards,
Daniel