* [U-Boot] Pull request: u-boot-arm
@ 2011-02-17 20:49 Albert ARIBAUD
2011-02-18 6:24 ` [U-Boot] PLEASE HOLD - " Albert ARIBAUD
0 siblings, 1 reply; 40+ messages in thread
From: Albert ARIBAUD @ 2011-02-17 20:49 UTC (permalink / raw)
To: u-boot
Hi Wolfgang,
The following changes since commit efb063390d2d1e712c2c8110911616244d562c4b:
add checking the CONFIG_ENV_IS_IN_SPI_FLASH in Enbedded env
(2011-02-15 22:09:50 +0100)
are available in the git repository at:
git://www.denx.de/git/u-boot-arm.git master
Alexander Stein (1):
arm relocation: Fix calculation of board_init_r
Fabio Estevam (3):
mx31pdk: Use the new relocation scheme
mx31pdk: Make the full boot log visible
arm1136: Fix NAND boot
Lei Wen (5):
mv: seperate kirkwood and armada from common setting
ARM: Add Support for Marvell Pantheon Familiy SoCs
serial: add pantheon soc support
mvmfp: add MFP configuration support for PANTHEON
Pantheon: Add Board Support for Marvell dkb board
Lo?c Minier (1):
EfikaMX: switch to MACH_TYPE_MX51_EFIKAMX
Po-Yu Chuang (1):
arm: get_sp() should always be compiled
Tom Warren (4):
arm: Tegra2: Add basic NVIDIA Tegra2 SoC support
serial: Add Tegra2 serial port support
arm: Tegra2: Add support for NVIDIA Harmony board
arm: Tegra2: Add support for NVIDIA Seaboard board
Wolfgang Denk (1):
ARM: fix write*() I/O accessors
MAINTAINERS | 9 +
README | 5 +
arch/arm/cpu/arm1136/start.S | 16 +--
arch/arm/cpu/arm926ejs/pantheon/Makefile | 46 ++++++
arch/arm/cpu/arm926ejs/pantheon/cpu.c | 78 +++++++++
arch/arm/cpu/arm926ejs/pantheon/dram.c | 132 +++++++++++++++
arch/arm/cpu/arm926ejs/pantheon/timer.c | 214
+++++++++++++++++++++++++
arch/arm/cpu/arm926ejs/start.S | 2 +-
arch/arm/cpu/armv7/tegra2/Makefile | 48 ++++++
arch/arm/cpu/armv7/tegra2/board.c | 88 ++++++++++
arch/arm/cpu/armv7/tegra2/config.mk | 28 ++++
arch/arm/cpu/armv7/tegra2/lowlevel_init.S | 65 ++++++++
arch/arm/cpu/armv7/tegra2/sys_info.c | 35 ++++
arch/arm/cpu/armv7/tegra2/timer.c | 122 ++++++++++++++
arch/arm/include/asm/arch-armada100/config.h | 44 +++++
arch/arm/include/asm/arch-kirkwood/config.h | 145 +++++++++++++++++
arch/arm/include/asm/arch-pantheon/config.h | 38 +++++
arch/arm/include/asm/arch-pantheon/cpu.h | 79 +++++++++
arch/arm/include/asm/arch-pantheon/mfp.h | 41 +++++
arch/arm/include/asm/arch-pantheon/pantheon.h | 54 ++++++
arch/arm/include/asm/arch-tegra2/clk_rst.h | 165 +++++++++++++++++++
arch/arm/include/asm/arch-tegra2/pinmux.h | 55 +++++++
arch/arm/include/asm/arch-tegra2/pmc.h | 124 ++++++++++++++
arch/arm/include/asm/arch-tegra2/sys_proto.h | 35 ++++
arch/arm/include/asm/arch-tegra2/tegra2.h | 49 ++++++
arch/arm/include/asm/arch-tegra2/uart.h | 47 ++++++
arch/arm/include/asm/io.h | 6 +-
arch/arm/lib/bootm.c | 4 +-
board/Marvell/dkb/Makefile | 51 ++++++
board/Marvell/dkb/dkb.c | 54 ++++++
board/efikamx/efikamx.c | 2 +-
board/freescale/mx31pdk/mx31pdk.c | 17 ++-
board/nvidia/common/board.c | 193
++++++++++++++++++++++
board/nvidia/harmony/Makefile | 50 ++++++
board/nvidia/seaboard/Makefile | 50 ++++++
boards.cfg | 3 +
common/serial.c | 3 +-
drivers/gpio/mvmfp.c | 2 +
drivers/serial/Makefile | 1 +
drivers/serial/serial.c | 2 +
drivers/serial/serial_tegra2.c | 77 +++++++++
drivers/serial/serial_tegra2.h | 29 ++++
include/configs/aspenite.h | 8 +
include/configs/dkb.h | 65 ++++++++
include/configs/harmony.h | 49 ++++++
include/configs/mv-common.h | 147 +++---------------
include/configs/mx31pdk.h | 7 +
include/configs/seaboard.h | 43 +++++
include/configs/tegra2-common.h | 160 ++++++++++++++++++
include/serial.h | 3 +-
nand_spl/board/freescale/mx31pdk/u-boot.lds | 59 ++++++-
51 files changed, 2691 insertions(+), 158 deletions(-)
create mode 100644 arch/arm/cpu/arm926ejs/pantheon/Makefile
create mode 100644 arch/arm/cpu/arm926ejs/pantheon/cpu.c
create mode 100644 arch/arm/cpu/arm926ejs/pantheon/dram.c
create mode 100644 arch/arm/cpu/arm926ejs/pantheon/timer.c
create mode 100644 arch/arm/cpu/armv7/tegra2/Makefile
create mode 100644 arch/arm/cpu/armv7/tegra2/board.c
create mode 100644 arch/arm/cpu/armv7/tegra2/config.mk
create mode 100644 arch/arm/cpu/armv7/tegra2/lowlevel_init.S
create mode 100644 arch/arm/cpu/armv7/tegra2/sys_info.c
create mode 100644 arch/arm/cpu/armv7/tegra2/timer.c
create mode 100644 arch/arm/include/asm/arch-armada100/config.h
create mode 100644 arch/arm/include/asm/arch-kirkwood/config.h
create mode 100644 arch/arm/include/asm/arch-pantheon/config.h
create mode 100644 arch/arm/include/asm/arch-pantheon/cpu.h
create mode 100644 arch/arm/include/asm/arch-pantheon/mfp.h
create mode 100644 arch/arm/include/asm/arch-pantheon/pantheon.h
create mode 100644 arch/arm/include/asm/arch-tegra2/clk_rst.h
create mode 100644 arch/arm/include/asm/arch-tegra2/pinmux.h
create mode 100644 arch/arm/include/asm/arch-tegra2/pmc.h
create mode 100644 arch/arm/include/asm/arch-tegra2/sys_proto.h
create mode 100644 arch/arm/include/asm/arch-tegra2/tegra2.h
create mode 100644 arch/arm/include/asm/arch-tegra2/uart.h
create mode 100644 board/Marvell/dkb/Makefile
create mode 100644 board/Marvell/dkb/dkb.c
create mode 100644 board/nvidia/common/board.c
create mode 100644 board/nvidia/harmony/Makefile
create mode 100644 board/nvidia/seaboard/Makefile
create mode 100644 drivers/serial/serial_tegra2.c
create mode 100644 drivers/serial/serial_tegra2.h
create mode 100644 include/configs/dkb.h
create mode 100644 include/configs/harmony.h
create mode 100644 include/configs/seaboard.h
create mode 100644 include/configs/tegra2-common.h
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 40+ messages in thread* [U-Boot] PLEASE HOLD - Re: Pull request: u-boot-arm
2011-02-17 20:49 [U-Boot] Pull request: u-boot-arm Albert ARIBAUD
@ 2011-02-18 6:24 ` Albert ARIBAUD
0 siblings, 0 replies; 40+ messages in thread
From: Albert ARIBAUD @ 2011-02-18 6:24 UTC (permalink / raw)
To: u-boot
Le 17/02/2011 21:49, Albert ARIBAUD a ?crit :
> Hi Wolfgang,
>
> The following changes since commit efb063390d2d1e712c2c8110911616244d562c4b:
>
> add checking the CONFIG_ENV_IS_IN_SPI_FLASH in Enbedded env
> (2011-02-15 22:09:50 +0100)
Wolfgang,
Please hold the pull for now.
I have added two patches to the list, the fix for a320 and the mach-type
fixes. I'll send out a new pull request at the end of today.
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
@ 2011-05-23 7:06 Albert ARIBAUD
0 siblings, 0 replies; 40+ messages in thread
From: Albert ARIBAUD @ 2011-05-23 7:06 UTC (permalink / raw)
To: u-boot
Hi Wolfgang,
The following changes since commit 5d1ee00b1fe1180503f6dfc10e87a6c6e74778f3:
.gitignore: update list of u-boot.* files and add *.bin (2011-05-22
23:46:26 +0200)
are available in the git repository at:
git://git.denx.de/u-boot-arm master
David M?ller (ELSOFT AG) (1):
VCMA9: use ARM relocation feature to fix build error
Fabio Estevam (6):
mx31pdk: Clean up mx31pdk.h file
MX53: Add initial support for MX53SMD board.
MX51: vision: Let video mode struct be independant of watchdog.
MX51: vision2: Fix build for vision2 board.
MX53: Handle silicon revision 2.1 case
MX53: Remove CONFIG_SYS_BOOTMAPSZ from mx53 config files.
Jason Kridner (1):
BeagleBoard: fixed typo in typecast
Jason Liu (2):
MX53: support for freescale MX53LOCO board
mx5: board: code clean up for checkboard code
Michael Walle (1):
mvsata: issue hard reset on initialization
Shawn Guo (2):
mx5: Remove unnecessary CONFIG_SYS_BOOTMAPSZ definition
mx5: Fix CONFIG_OF_LIBFDT redefined warning
Stefano Babic (3):
MX31: Make get_reset_cause() static and drop unreachable code
MX5: drop config.mk from efikamx board
MX31: drop warnings due to missing prototype for mxc_watchdog_reset()
MAINTAINERS | 2 +
arch/arm/cpu/arm1136/mx31/generic.c | 6 +-
arch/arm/cpu/armv7/mx5/soc.c | 10 +-
arch/arm/include/asm/arch-mx31/clock.h | 1 +
board/efikamx/efikamx.c | 42 +---
board/freescale/mx51evk/mx51evk.c | 36 +---
board/freescale/mx53evk/mx53evk.c | 21 +--
.../config.mk => freescale/mx53loco/Makefile} | 36 ++-
board/freescale/mx53loco/imximage.cfg | 96 ++++++
board/freescale/mx53loco/mx53loco.c | 302
++++++++++++++++++++
.../config.mk => freescale/mx53smd/Makefile} | 35 ++-
board/freescale/mx53smd/imximage.cfg | 96 ++++++
board/freescale/mx53smd/mx53smd.c | 229 +++++++++++++++
board/ti/beagle/beagle.c | 2 +-
board/ttcontrol/vision2/vision2.c | 47 +---
boards.cfg | 6 +-
drivers/block/mvsata_ide.c | 10 +-
include/configs/VCMA9.h | 5 +
include/configs/mx31pdk.h | 32 +-
include/configs/mx51evk.h | 3 -
include/configs/mx53evk.h | 3 -
include/configs/mx53loco.h | 185 ++++++++++++
include/configs/mx53smd.h | 191 ++++++++++++
include/configs/vision2.h | 1 +
24 files changed, 1206 insertions(+), 191 deletions(-)
rename board/{efikamx/config.mk => freescale/mx53loco/Makefile} (51%)
create mode 100644 board/freescale/mx53loco/imximage.cfg
create mode 100644 board/freescale/mx53loco/mx53loco.c
rename board/{ttcontrol/vision2/config.mk =>
freescale/mx53smd/Makefile} (50%)
create mode 100644 board/freescale/mx53smd/imximage.cfg
create mode 100644 board/freescale/mx53smd/mx53smd.c
create mode 100644 include/configs/mx53loco.h
create mode 100644 include/configs/mx53smd.h
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 40+ messages in thread* [U-Boot] Pull request: u-boot-arm
@ 2011-05-18 12:20 Albert ARIBAUD
2011-05-18 12:42 ` Wolfgang Denk
0 siblings, 1 reply; 40+ messages in thread
From: Albert ARIBAUD @ 2011-05-18 12:20 UTC (permalink / raw)
To: u-boot
Hi Wolfgang,
The following changes since commit 535abb96fb665402894b820f934deaca61ce3d3e:
Merge branch 'master' of git://git.denx.de/u-boot-nand-flash
(2011-05-15 23:23:36 +0200)
are available in the git repository at:
git://git.denx.de/u-boot-arm master
Andreas Bie?mann (19):
avr32: rename memory-map.h -> hardware.h
avr32: fixup definitions to ATMEL_BASE_xxx
avr32: fix linking
avr32/config.mk: simplify PLATFORM_RELFLAGS
avr32: use single linker script
atngw100: fix "#define XXXX 1"
atstk1002: fix "#define XXXX 1"
atstk1003: fix "#define XXXX 1"
atstk1004: fix "#define XXXX 1"
atstk1006: fix "#define XXXX 1"
favr-32-ezkit: fix "#define XXXX 1"
hammerhead: fix "#define XXXX 1"
mimc200: fix "#define XXXX 1"
atngw100: move CONFIG_SYS_TEXT_BASE to header
atstk100x: move CONFIG_SYS_TEXT_BASE to header
favr-32-ezkit: move CONFIG_SYS_TEXT_BASE to header
mimc200: move CONFIG_SYS_TEXT_BASE to header
hammerhead: move CONFIG_SYS_TEXT_BASE to header
avr32: add ATAG_BOARDINFO
Daniel Gorsulowski (3):
at91: fixed at91sam9263 system file
at91: reworked support for meesc board
at91: reworked support for otc570 board
Jens Scharsig (2):
at91rm9200: fix lowlevel_init() SMRDATA size
remove __attribute__ ((packed)) in at91 headers
Reinhard Meyer (15):
AT91: rework at91sam9260.h
AT91: rework at91sam9261.h
AT91: rework at91sam9263.h
AT91: rework at91sam9g45.h
AT91: cleanup hardware.h, remove memory-map.h
AT91: fix related arch-at91 header files
AT91: fix related at91 system/driver files
AT91: fix related at91 driver files
ATMEL: fix related common atmel driver files
AT91: cleanup at91sam9260_matrix.h to struct SoC access
AT91: change includes from asm/arch/io.h to asm/io.h
ATMEL: fix dataflash (dirty) this file should be converted to
struct SoC access
AT91: remove LEGACY from at91_rstc.h
AT91: fix at91sam_wdt.c to reworked header files
AT91: fix timer.c - remove reset_timer()
Ryan Mallon (1):
Add support for Bluewater Systems Snapper 9260 and 9G20 modules
arch/arm/cpu/arm920t/at91/lowlevel_init.S | 8 +-
arch/arm/cpu/arm926ejs/at91/Makefile | 1 +
arch/arm/cpu/arm926ejs/at91/at91sam9260_devices.c | 47 +---
arch/arm/cpu/arm926ejs/at91/at91sam9263_devices.c | 55 ++---
arch/arm/cpu/arm926ejs/at91/clock.c | 8 +-
arch/arm/cpu/arm926ejs/at91/cpu.c | 11 +-
arch/arm/cpu/arm926ejs/at91/eflash.c | 16 +-
arch/arm/cpu/arm926ejs/at91/led.c | 2 +-
arch/arm/cpu/arm926ejs/at91/reset.c | 4 +-
arch/arm/cpu/arm926ejs/at91/timer.c | 37 ++--
arch/arm/include/asm/arch-at91/at91_common.h | 3 +-
arch/arm/include/asm/arch-at91/at91_mc.h | 10 +-
arch/arm/include/asm/arch-at91/at91_pio.h | 19 +--
arch/arm/include/asm/arch-at91/at91_rstc.h | 25 --
arch/arm/include/asm/arch-at91/at91_st.h | 2 +-
arch/arm/include/asm/arch-at91/at91_tc.h | 4 +-
arch/arm/include/asm/arch-at91/at91sam9260.h | 252
++++++++++---------
.../arm/include/asm/arch-at91/at91sam9260_matrix.h | 102 ++++-----
arch/arm/include/asm/arch-at91/at91sam9261.h | 187 ++++++++-------
arch/arm/include/asm/arch-at91/at91sam9263.h | 218
++++++++---------
arch/arm/include/asm/arch-at91/at91sam9g45.h | 225
++++++++---------
arch/arm/include/asm/arch-at91/gpio.h | 18 +-
arch/arm/include/asm/arch-at91/hardware.h | 96 +++-----
arch/arm/include/asm/arch-at91/io.h | 43 ----
arch/arm/include/asm/arch-at91/memory-map.h | 36 ---
arch/avr32/config.mk | 6 +-
arch/avr32/cpu/at32ap700x/clk.c | 2 +-
arch/avr32/cpu/at32ap700x/portmux.c | 2 +-
arch/avr32/cpu/at32ap700x/sm.h | 4 +-
arch/avr32/cpu/cpu.c | 2 +-
arch/avr32/cpu/hsdramc.c | 2 +-
arch/avr32/cpu/hsdramc1.h | 4 +-
arch/avr32/cpu/hsmc3.h | 4 +-
arch/avr32/cpu/interrupts.c | 4 +-
arch/avr32/cpu/portmux-gpio.c | 2 +-
arch/avr32/cpu/portmux-pio.c | 2 +-
.../atmel/atstk1000 => arch/avr32/cpu}/u-boot.lds | 0
arch/avr32/include/asm/arch-at32ap700x/gpio.h | 12 +-
.../arch-at32ap700x/{memory-map.h => hardware.h} | 76 +++---
arch/avr32/include/asm/arch-at32ap700x/portmux.h | 10 +-
arch/avr32/include/asm/hmatrix-common.h | 2 +-
arch/avr32/include/asm/setup.h | 8 +
arch/avr32/lib/bootm.c | 11 +
board/atmel/atngw100/atngw100.c | 4 +-
board/atmel/atngw100/config.mk | 3 -
board/atmel/atngw100/u-boot.lds | 72 ------
board/atmel/atstk1000/atstk1000.c | 4 +-
board/atmel/atstk1000/config.mk | 3 -
board/earthlcd/favr-32-ezkit/config.mk | 3 -
board/earthlcd/favr-32-ezkit/favr-32-ezkit.c | 3 +-
board/earthlcd/favr-32-ezkit/u-boot.lds | 70 -----
board/esd/otc570/config.mk | 1 -
board/esd/otc570/otc570.c | 106 +++++----
board/mimc/mimc200/config.mk | 3 -
board/mimc/mimc200/mimc200.c | 4 +-
board/mimc/mimc200/u-boot.lds | 72 ------
board/miromico/hammerhead/config.mk | 3 -
board/miromico/hammerhead/hammerhead.c | 5 +-
board/miromico/hammerhead/u-boot.lds | 72 ------
boards.cfg | 8 +-
drivers/gpio/at91_gpio.c | 54 +++--
drivers/mmc/atmel_mci.c | 2 +-
drivers/mmc/atmel_mci.h | 4 +-
drivers/mmc/gen_atmel_mci.c | 2 +-
drivers/net/macb.c | 14 +-
drivers/rtc/at91sam9_rtt.c | 14 +-
drivers/serial/atmel_usart.c | 28 +--
drivers/spi/atmel_dataflash_spi.c | 94 +++++---
drivers/spi/atmel_spi.c | 16 +-
drivers/usb/host/ohci-at91.c | 18 +-
drivers/watchdog/at91sam9_wdt.c | 6 +-
include/configs/atngw100.h | 61 +++---
include/configs/atstk1002.h | 57 ++---
include/configs/atstk1003.h | 51 ++--
include/configs/atstk1004.h | 51 ++--
include/configs/atstk1006.h | 57 ++---
include/configs/favr-32-ezkit.h | 55 ++--
include/configs/hammerhead.h | 52 ++--
include/configs/mimc200.h | 63 +++---
include/configs/otc570.h | 265
+++++++++++---------
include/dataflash.h | 1 -
81 files changed, 1287 insertions(+), 1696 deletions(-)
delete mode 100644 arch/arm/include/asm/arch-at91/io.h
delete mode 100644 arch/arm/include/asm/arch-at91/memory-map.h
rename {board/atmel/atstk1000 => arch/avr32/cpu}/u-boot.lds (100%)
rename arch/avr32/include/asm/arch-at32ap700x/{memory-map.h =>
hardware.h} (53%)
delete mode 100644 board/atmel/atngw100/config.mk
delete mode 100644 board/atmel/atngw100/u-boot.lds
delete mode 100644 board/atmel/atstk1000/config.mk
delete mode 100644 board/earthlcd/favr-32-ezkit/config.mk
delete mode 100644 board/earthlcd/favr-32-ezkit/u-boot.lds
delete mode 100644 board/esd/otc570/config.mk
delete mode 100644 board/mimc/mimc200/config.mk
delete mode 100644 board/mimc/mimc200/u-boot.lds
delete mode 100644 board/miromico/hammerhead/config.mk
delete mode 100644 board/miromico/hammerhead/u-boot.lds
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 40+ messages in thread* [U-Boot] Pull request: u-boot-arm
2011-05-18 12:20 Albert ARIBAUD
@ 2011-05-18 12:42 ` Wolfgang Denk
0 siblings, 0 replies; 40+ messages in thread
From: Wolfgang Denk @ 2011-05-18 12:42 UTC (permalink / raw)
To: u-boot
Dear Albert ARIBAUD,
In message <4DD3B9A3.2080908@aribaud.net> you wrote:
> Hi Wolfgang,
>
> The following changes since commit 535abb96fb665402894b820f934deaca61ce3d3e:
>
> Merge branch 'master' of git://git.denx.de/u-boot-nand-flash
> (2011-05-15 23:23:36 +0200)
>
> are available in the git repository at:
>
> git://git.denx.de/u-boot-arm master
>
> Andreas Bie?mann (19):
> avr32: rename memory-map.h -> hardware.h
> avr32: fixup definitions to ATMEL_BASE_xxx
> avr32: fix linking
> avr32/config.mk: simplify PLATFORM_RELFLAGS
> avr32: use single linker script
> atngw100: fix "#define XXXX 1"
> atstk1002: fix "#define XXXX 1"
> atstk1003: fix "#define XXXX 1"
> atstk1004: fix "#define XXXX 1"
> atstk1006: fix "#define XXXX 1"
> favr-32-ezkit: fix "#define XXXX 1"
> hammerhead: fix "#define XXXX 1"
> mimc200: fix "#define XXXX 1"
> atngw100: move CONFIG_SYS_TEXT_BASE to header
> atstk100x: move CONFIG_SYS_TEXT_BASE to header
> favr-32-ezkit: move CONFIG_SYS_TEXT_BASE to header
> mimc200: move CONFIG_SYS_TEXT_BASE to header
> hammerhead: move CONFIG_SYS_TEXT_BASE to header
> avr32: add ATAG_BOARDINFO
>
> Daniel Gorsulowski (3):
> at91: fixed at91sam9263 system file
> at91: reworked support for meesc board
> at91: reworked support for otc570 board
>
> Jens Scharsig (2):
> at91rm9200: fix lowlevel_init() SMRDATA size
> remove __attribute__ ((packed)) in at91 headers
>
> Reinhard Meyer (15):
> AT91: rework at91sam9260.h
> AT91: rework at91sam9261.h
> AT91: rework at91sam9263.h
> AT91: rework at91sam9g45.h
> AT91: cleanup hardware.h, remove memory-map.h
> AT91: fix related arch-at91 header files
> AT91: fix related at91 system/driver files
> AT91: fix related at91 driver files
> ATMEL: fix related common atmel driver files
> AT91: cleanup at91sam9260_matrix.h to struct SoC access
> AT91: change includes from asm/arch/io.h to asm/io.h
> ATMEL: fix dataflash (dirty) this file should be converted to
> struct SoC access
> AT91: remove LEGACY from at91_rstc.h
> AT91: fix at91sam_wdt.c to reworked header files
> AT91: fix timer.c - remove reset_timer()
>
> Ryan Mallon (1):
> Add support for Bluewater Systems Snapper 9260 and 9G20 modules
>
> arch/arm/cpu/arm920t/at91/lowlevel_init.S | 8 +-
> arch/arm/cpu/arm926ejs/at91/Makefile | 1 +
> arch/arm/cpu/arm926ejs/at91/at91sam9260_devices.c | 47 +---
> arch/arm/cpu/arm926ejs/at91/at91sam9263_devices.c | 55 ++---
> arch/arm/cpu/arm926ejs/at91/clock.c | 8 +-
> arch/arm/cpu/arm926ejs/at91/cpu.c | 11 +-
> arch/arm/cpu/arm926ejs/at91/eflash.c | 16 +-
> arch/arm/cpu/arm926ejs/at91/led.c | 2 +-
> arch/arm/cpu/arm926ejs/at91/reset.c | 4 +-
> arch/arm/cpu/arm926ejs/at91/timer.c | 37 ++--
> arch/arm/include/asm/arch-at91/at91_common.h | 3 +-
> arch/arm/include/asm/arch-at91/at91_mc.h | 10 +-
> arch/arm/include/asm/arch-at91/at91_pio.h | 19 +--
> arch/arm/include/asm/arch-at91/at91_rstc.h | 25 --
> arch/arm/include/asm/arch-at91/at91_st.h | 2 +-
> arch/arm/include/asm/arch-at91/at91_tc.h | 4 +-
> arch/arm/include/asm/arch-at91/at91sam9260.h | 252
> ++++++++++---------
> .../arm/include/asm/arch-at91/at91sam9260_matrix.h | 102 ++++-----
> arch/arm/include/asm/arch-at91/at91sam9261.h | 187 ++++++++-------
> arch/arm/include/asm/arch-at91/at91sam9263.h | 218
> ++++++++---------
> arch/arm/include/asm/arch-at91/at91sam9g45.h | 225
> ++++++++---------
> arch/arm/include/asm/arch-at91/gpio.h | 18 +-
> arch/arm/include/asm/arch-at91/hardware.h | 96 +++-----
> arch/arm/include/asm/arch-at91/io.h | 43 ----
> arch/arm/include/asm/arch-at91/memory-map.h | 36 ---
> arch/avr32/config.mk | 6 +-
> arch/avr32/cpu/at32ap700x/clk.c | 2 +-
> arch/avr32/cpu/at32ap700x/portmux.c | 2 +-
> arch/avr32/cpu/at32ap700x/sm.h | 4 +-
> arch/avr32/cpu/cpu.c | 2 +-
> arch/avr32/cpu/hsdramc.c | 2 +-
> arch/avr32/cpu/hsdramc1.h | 4 +-
> arch/avr32/cpu/hsmc3.h | 4 +-
> arch/avr32/cpu/interrupts.c | 4 +-
> arch/avr32/cpu/portmux-gpio.c | 2 +-
> arch/avr32/cpu/portmux-pio.c | 2 +-
> .../atmel/atstk1000 => arch/avr32/cpu}/u-boot.lds | 0
> arch/avr32/include/asm/arch-at32ap700x/gpio.h | 12 +-
> .../arch-at32ap700x/{memory-map.h => hardware.h} | 76 +++---
> arch/avr32/include/asm/arch-at32ap700x/portmux.h | 10 +-
> arch/avr32/include/asm/hmatrix-common.h | 2 +-
> arch/avr32/include/asm/setup.h | 8 +
> arch/avr32/lib/bootm.c | 11 +
> board/atmel/atngw100/atngw100.c | 4 +-
> board/atmel/atngw100/config.mk | 3 -
> board/atmel/atngw100/u-boot.lds | 72 ------
> board/atmel/atstk1000/atstk1000.c | 4 +-
> board/atmel/atstk1000/config.mk | 3 -
> board/earthlcd/favr-32-ezkit/config.mk | 3 -
> board/earthlcd/favr-32-ezkit/favr-32-ezkit.c | 3 +-
> board/earthlcd/favr-32-ezkit/u-boot.lds | 70 -----
> board/esd/otc570/config.mk | 1 -
> board/esd/otc570/otc570.c | 106 +++++----
> board/mimc/mimc200/config.mk | 3 -
> board/mimc/mimc200/mimc200.c | 4 +-
> board/mimc/mimc200/u-boot.lds | 72 ------
> board/miromico/hammerhead/config.mk | 3 -
> board/miromico/hammerhead/hammerhead.c | 5 +-
> board/miromico/hammerhead/u-boot.lds | 72 ------
> boards.cfg | 8 +-
> drivers/gpio/at91_gpio.c | 54 +++--
> drivers/mmc/atmel_mci.c | 2 +-
> drivers/mmc/atmel_mci.h | 4 +-
> drivers/mmc/gen_atmel_mci.c | 2 +-
> drivers/net/macb.c | 14 +-
> drivers/rtc/at91sam9_rtt.c | 14 +-
> drivers/serial/atmel_usart.c | 28 +--
> drivers/spi/atmel_dataflash_spi.c | 94 +++++---
> drivers/spi/atmel_spi.c | 16 +-
> drivers/usb/host/ohci-at91.c | 18 +-
> drivers/watchdog/at91sam9_wdt.c | 6 +-
> include/configs/atngw100.h | 61 +++---
> include/configs/atstk1002.h | 57 ++---
> include/configs/atstk1003.h | 51 ++--
> include/configs/atstk1004.h | 51 ++--
> include/configs/atstk1006.h | 57 ++---
> include/configs/favr-32-ezkit.h | 55 ++--
> include/configs/hammerhead.h | 52 ++--
> include/configs/mimc200.h | 63 +++---
> include/configs/otc570.h | 265
> +++++++++++---------
> include/dataflash.h | 1 -
> 81 files changed, 1287 insertions(+), 1696 deletions(-)
> delete mode 100644 arch/arm/include/asm/arch-at91/io.h
> delete mode 100644 arch/arm/include/asm/arch-at91/memory-map.h
> rename {board/atmel/atstk1000 => arch/avr32/cpu}/u-boot.lds (100%)
> rename arch/avr32/include/asm/arch-at32ap700x/{memory-map.h =>
> hardware.h} (53%)
> delete mode 100644 board/atmel/atngw100/config.mk
> delete mode 100644 board/atmel/atngw100/u-boot.lds
> delete mode 100644 board/atmel/atstk1000/config.mk
> delete mode 100644 board/earthlcd/favr-32-ezkit/config.mk
> delete mode 100644 board/earthlcd/favr-32-ezkit/u-boot.lds
> delete mode 100644 board/esd/otc570/config.mk
> delete mode 100644 board/mimc/mimc200/config.mk
> delete mode 100644 board/mimc/mimc200/u-boot.lds
> delete mode 100644 board/miromico/hammerhead/config.mk
> delete mode 100644 board/miromico/hammerhead/u-boot.lds
Applied, thanks.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Do not underestimate the value of print statements for debugging.
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
@ 2011-02-21 7:33 Albert ARIBAUD
2011-02-21 22:16 ` Wolfgang Denk
0 siblings, 1 reply; 40+ messages in thread
From: Albert ARIBAUD @ 2011-02-21 7:33 UTC (permalink / raw)
To: u-boot
Hi Wolfgang,
Please pull the following from u-boot-arm/master.
Amicalement,
Albert.
The following changes since commit c650e1be41536a453d115e6b73898fa5dabdadc2:
Fix compile warning in net/eth.c (2011-02-19 20:32:38 +0100)
are available in the git repository at:
git://www.denx.de/git/u-boot-arm.git master
Alexander Stein (1):
arm relocation: Fix calculation of board_init_r
Fabio Estevam (4):
mx31pdk: Use the new relocation scheme
mx31pdk: Make the full boot log visible
arm1136: Fix NAND boot
arm1136 relocation: Fix calculation of board_init_r
Lei Wen (5):
mv: seperate kirkwood and armada from common setting
ARM: Add Support for Marvell Pantheon Familiy SoCs
serial: add pantheon soc support
mvmfp: add MFP configuration support for PANTHEON
Pantheon: Add Board Support for Marvell dkb board
Lo?c Minier (1):
EfikaMX: switch to MACH_TYPE_MX51_EFIKAMX
Po-Yu Chuang (1):
arm: get_sp() should always be compiled
Sandeep Paulraj (1):
ARM: Update mach-types
Tom Warren (4):
arm: Tegra2: Add basic NVIDIA Tegra2 SoC support
serial: Add Tegra2 serial port support
arm: Tegra2: Add support for NVIDIA Harmony board
arm: Tegra2: Add support for NVIDIA Seaboard board
Wolfgang Denk (1):
ARM: fix write*() I/O accessors
MAINTAINERS | 9 +
README | 5 +
arch/arm/cpu/arm1136/start.S | 18 +-
arch/arm/cpu/arm926ejs/pantheon/Makefile | 46 +
arch/arm/cpu/arm926ejs/pantheon/cpu.c | 78 ++
arch/arm/cpu/arm926ejs/pantheon/dram.c | 132 +++
arch/arm/cpu/arm926ejs/pantheon/timer.c | 214 ++++
arch/arm/cpu/arm926ejs/start.S | 2 +-
arch/arm/cpu/armv7/tegra2/Makefile | 48 +
arch/arm/cpu/armv7/tegra2/board.c | 88 ++
arch/arm/cpu/armv7/tegra2/config.mk | 28 +
arch/arm/cpu/armv7/tegra2/lowlevel_init.S | 65 ++
arch/arm/cpu/armv7/tegra2/sys_info.c | 35 +
arch/arm/cpu/armv7/tegra2/timer.c | 122 +++
arch/arm/include/asm/arch-armada100/config.h | 44 +
arch/arm/include/asm/arch-kirkwood/config.h | 145 +++
arch/arm/include/asm/arch-pantheon/config.h | 38 +
arch/arm/include/asm/arch-pantheon/cpu.h | 79 ++
arch/arm/include/asm/arch-pantheon/mfp.h | 41 +
arch/arm/include/asm/arch-pantheon/pantheon.h | 54 +
arch/arm/include/asm/arch-tegra2/clk_rst.h | 165 ++++
arch/arm/include/asm/arch-tegra2/pinmux.h | 55 ++
arch/arm/include/asm/arch-tegra2/pmc.h | 124 +++
arch/arm/include/asm/arch-tegra2/sys_proto.h | 35 +
arch/arm/include/asm/arch-tegra2/tegra2.h | 49 +
arch/arm/include/asm/arch-tegra2/uart.h | 47 +
arch/arm/include/asm/io.h | 6 +-
arch/arm/include/asm/mach-types.h | 1291
++++++++++++++++++++++++-
arch/arm/lib/bootm.c | 4 +-
board/Marvell/dkb/Makefile | 51 +
board/Marvell/dkb/dkb.c | 54 +
board/efikamx/efikamx.c | 2 +-
board/freescale/mx31pdk/mx31pdk.c | 17 +-
board/nvidia/common/board.c | 193 ++++
board/nvidia/harmony/Makefile | 50 +
board/nvidia/seaboard/Makefile | 50 +
boards.cfg | 3 +
common/serial.c | 3 +-
drivers/gpio/mvmfp.c | 2 +
drivers/serial/Makefile | 1 +
drivers/serial/serial.c | 2 +
drivers/serial/serial_tegra2.c | 77 ++
drivers/serial/serial_tegra2.h | 29 +
include/configs/aspenite.h | 8 +
include/configs/dkb.h | 65 ++
include/configs/harmony.h | 49 +
include/configs/mv-common.h | 147 +---
include/configs/mx31pdk.h | 7 +
include/configs/seaboard.h | 43 +
include/configs/tegra2-common.h | 160 +++
include/serial.h | 3 +-
nand_spl/board/freescale/mx31pdk/u-boot.lds | 59 +-
52 files changed, 3968 insertions(+), 174 deletions(-)
create mode 100644 arch/arm/cpu/arm926ejs/pantheon/Makefile
create mode 100644 arch/arm/cpu/arm926ejs/pantheon/cpu.c
create mode 100644 arch/arm/cpu/arm926ejs/pantheon/dram.c
create mode 100644 arch/arm/cpu/arm926ejs/pantheon/timer.c
create mode 100644 arch/arm/cpu/armv7/tegra2/Makefile
create mode 100644 arch/arm/cpu/armv7/tegra2/board.c
create mode 100644 arch/arm/cpu/armv7/tegra2/config.mk
create mode 100644 arch/arm/cpu/armv7/tegra2/lowlevel_init.S
create mode 100644 arch/arm/cpu/armv7/tegra2/sys_info.c
create mode 100644 arch/arm/cpu/armv7/tegra2/timer.c
create mode 100644 arch/arm/include/asm/arch-armada100/config.h
create mode 100644 arch/arm/include/asm/arch-kirkwood/config.h
create mode 100644 arch/arm/include/asm/arch-pantheon/config.h
create mode 100644 arch/arm/include/asm/arch-pantheon/cpu.h
create mode 100644 arch/arm/include/asm/arch-pantheon/mfp.h
create mode 100644 arch/arm/include/asm/arch-pantheon/pantheon.h
create mode 100644 arch/arm/include/asm/arch-tegra2/clk_rst.h
create mode 100644 arch/arm/include/asm/arch-tegra2/pinmux.h
create mode 100644 arch/arm/include/asm/arch-tegra2/pmc.h
create mode 100644 arch/arm/include/asm/arch-tegra2/sys_proto.h
create mode 100644 arch/arm/include/asm/arch-tegra2/tegra2.h
create mode 100644 arch/arm/include/asm/arch-tegra2/uart.h
create mode 100644 board/Marvell/dkb/Makefile
create mode 100644 board/Marvell/dkb/dkb.c
create mode 100644 board/nvidia/common/board.c
create mode 100644 board/nvidia/harmony/Makefile
create mode 100644 board/nvidia/seaboard/Makefile
create mode 100644 drivers/serial/serial_tegra2.c
create mode 100644 drivers/serial/serial_tegra2.h
create mode 100644 include/configs/dkb.h
create mode 100644 include/configs/harmony.h
create mode 100644 include/configs/seaboard.h
create mode 100644 include/configs/tegra2-common.h
^ permalink raw reply [flat|nested] 40+ messages in thread* [U-Boot] Pull request: u-boot-arm
2011-02-21 7:33 Albert ARIBAUD
@ 2011-02-21 22:16 ` Wolfgang Denk
0 siblings, 0 replies; 40+ messages in thread
From: Wolfgang Denk @ 2011-02-21 22:16 UTC (permalink / raw)
To: u-boot
Dear Albert ARIBAUD,
In message <4D621552.7090101@free.fr> you wrote:
> Hi Wolfgang,
>
> Please pull the following from u-boot-arm/master.
>
> Amicalement,
> Albert.
>
> The following changes since commit c650e1be41536a453d115e6b73898fa5dabdadc2:
>
> Fix compile warning in net/eth.c (2011-02-19 20:32:38 +0100)
>
> are available in the git repository at:
> git://www.denx.de/git/u-boot-arm.git master
>
> Alexander Stein (1):
> arm relocation: Fix calculation of board_init_r
>
> Fabio Estevam (4):
> mx31pdk: Use the new relocation scheme
> mx31pdk: Make the full boot log visible
> arm1136: Fix NAND boot
> arm1136 relocation: Fix calculation of board_init_r
>
> Lei Wen (5):
> mv: seperate kirkwood and armada from common setting
> ARM: Add Support for Marvell Pantheon Familiy SoCs
> serial: add pantheon soc support
> mvmfp: add MFP configuration support for PANTHEON
> Pantheon: Add Board Support for Marvell dkb board
>
> Lo?c Minier (1):
> EfikaMX: switch to MACH_TYPE_MX51_EFIKAMX
>
> Po-Yu Chuang (1):
> arm: get_sp() should always be compiled
>
> Sandeep Paulraj (1):
> ARM: Update mach-types
>
> Tom Warren (4):
> arm: Tegra2: Add basic NVIDIA Tegra2 SoC support
> serial: Add Tegra2 serial port support
> arm: Tegra2: Add support for NVIDIA Harmony board
> arm: Tegra2: Add support for NVIDIA Seaboard board
>
> Wolfgang Denk (1):
> ARM: fix write*() I/O accessors
>
> MAINTAINERS | 9 +
> README | 5 +
> arch/arm/cpu/arm1136/start.S | 18 +-
> arch/arm/cpu/arm926ejs/pantheon/Makefile | 46 +
> arch/arm/cpu/arm926ejs/pantheon/cpu.c | 78 ++
> arch/arm/cpu/arm926ejs/pantheon/dram.c | 132 +++
> arch/arm/cpu/arm926ejs/pantheon/timer.c | 214 ++++
> arch/arm/cpu/arm926ejs/start.S | 2 +-
> arch/arm/cpu/armv7/tegra2/Makefile | 48 +
> arch/arm/cpu/armv7/tegra2/board.c | 88 ++
> arch/arm/cpu/armv7/tegra2/config.mk | 28 +
> arch/arm/cpu/armv7/tegra2/lowlevel_init.S | 65 ++
> arch/arm/cpu/armv7/tegra2/sys_info.c | 35 +
> arch/arm/cpu/armv7/tegra2/timer.c | 122 +++
> arch/arm/include/asm/arch-armada100/config.h | 44 +
> arch/arm/include/asm/arch-kirkwood/config.h | 145 +++
> arch/arm/include/asm/arch-pantheon/config.h | 38 +
> arch/arm/include/asm/arch-pantheon/cpu.h | 79 ++
> arch/arm/include/asm/arch-pantheon/mfp.h | 41 +
> arch/arm/include/asm/arch-pantheon/pantheon.h | 54 +
> arch/arm/include/asm/arch-tegra2/clk_rst.h | 165 ++++
> arch/arm/include/asm/arch-tegra2/pinmux.h | 55 ++
> arch/arm/include/asm/arch-tegra2/pmc.h | 124 +++
> arch/arm/include/asm/arch-tegra2/sys_proto.h | 35 +
> arch/arm/include/asm/arch-tegra2/tegra2.h | 49 +
> arch/arm/include/asm/arch-tegra2/uart.h | 47 +
> arch/arm/include/asm/io.h | 6 +-
> arch/arm/include/asm/mach-types.h | 1291
> ++++++++++++++++++++++++-
> arch/arm/lib/bootm.c | 4 +-
> board/Marvell/dkb/Makefile | 51 +
> board/Marvell/dkb/dkb.c | 54 +
> board/efikamx/efikamx.c | 2 +-
> board/freescale/mx31pdk/mx31pdk.c | 17 +-
> board/nvidia/common/board.c | 193 ++++
> board/nvidia/harmony/Makefile | 50 +
> board/nvidia/seaboard/Makefile | 50 +
> boards.cfg | 3 +
> common/serial.c | 3 +-
> drivers/gpio/mvmfp.c | 2 +
> drivers/serial/Makefile | 1 +
> drivers/serial/serial.c | 2 +
> drivers/serial/serial_tegra2.c | 77 ++
> drivers/serial/serial_tegra2.h | 29 +
> include/configs/aspenite.h | 8 +
> include/configs/dkb.h | 65 ++
> include/configs/harmony.h | 49 +
> include/configs/mv-common.h | 147 +---
> include/configs/mx31pdk.h | 7 +
> include/configs/seaboard.h | 43 +
> include/configs/tegra2-common.h | 160 +++
> include/serial.h | 3 +-
> nand_spl/board/freescale/mx31pdk/u-boot.lds | 59 +-
> 52 files changed, 3968 insertions(+), 174 deletions(-)
> create mode 100644 arch/arm/cpu/arm926ejs/pantheon/Makefile
> create mode 100644 arch/arm/cpu/arm926ejs/pantheon/cpu.c
> create mode 100644 arch/arm/cpu/arm926ejs/pantheon/dram.c
> create mode 100644 arch/arm/cpu/arm926ejs/pantheon/timer.c
> create mode 100644 arch/arm/cpu/armv7/tegra2/Makefile
> create mode 100644 arch/arm/cpu/armv7/tegra2/board.c
> create mode 100644 arch/arm/cpu/armv7/tegra2/config.mk
> create mode 100644 arch/arm/cpu/armv7/tegra2/lowlevel_init.S
> create mode 100644 arch/arm/cpu/armv7/tegra2/sys_info.c
> create mode 100644 arch/arm/cpu/armv7/tegra2/timer.c
> create mode 100644 arch/arm/include/asm/arch-armada100/config.h
> create mode 100644 arch/arm/include/asm/arch-kirkwood/config.h
> create mode 100644 arch/arm/include/asm/arch-pantheon/config.h
> create mode 100644 arch/arm/include/asm/arch-pantheon/cpu.h
> create mode 100644 arch/arm/include/asm/arch-pantheon/mfp.h
> create mode 100644 arch/arm/include/asm/arch-pantheon/pantheon.h
> create mode 100644 arch/arm/include/asm/arch-tegra2/clk_rst.h
> create mode 100644 arch/arm/include/asm/arch-tegra2/pinmux.h
> create mode 100644 arch/arm/include/asm/arch-tegra2/pmc.h
> create mode 100644 arch/arm/include/asm/arch-tegra2/sys_proto.h
> create mode 100644 arch/arm/include/asm/arch-tegra2/tegra2.h
> create mode 100644 arch/arm/include/asm/arch-tegra2/uart.h
> create mode 100644 board/Marvell/dkb/Makefile
> create mode 100644 board/Marvell/dkb/dkb.c
> create mode 100644 board/nvidia/common/board.c
> create mode 100644 board/nvidia/harmony/Makefile
> create mode 100644 board/nvidia/seaboard/Makefile
> create mode 100644 drivers/serial/serial_tegra2.c
> create mode 100644 drivers/serial/serial_tegra2.h
> create mode 100644 include/configs/dkb.h
> create mode 100644 include/configs/harmony.h
> create mode 100644 include/configs/seaboard.h
> create mode 100644 include/configs/tegra2-common.h
Applied, thanks!
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"I dislike companies that have a we-are-the-high-priests-of-hardware-
so-you'll-like-what-we-give-you attitude. I like commodity markets in
which iron-and-silicon hawkers know that they exist to provide fast
toys for software types like me to play with..." - Eric S. Raymond
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
@ 2011-02-02 0:09 Albert ARIBAUD
2011-02-02 20:57 ` Wolfgang Denk
0 siblings, 1 reply; 40+ messages in thread
From: Albert ARIBAUD @ 2011-02-02 0:09 UTC (permalink / raw)
To: u-boot
Hi Wolfgang,
Please pull from u-boot-arm/master to go into rc1 of upcoming release.
The following changes since commit 6f918bd46482f889f4d94623b09daf659a1974bd:
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx (2011-01-31
23:20:32 +0100)
are available in the git repository at:
git://www.denx.de/git/u-boot-arm.git master
Alexander Holler (1):
ARM: Avoid compiler optimization for readb, writeb and friends.
Anatolij Gustschin (2):
SPI: mxc_spi: fix swapping bug and add missing swapping in
unaligned rx case
SPI: mxc_spi: add SPI clock calculation and setup to the driver
Heiko Schocher (2):
arm1136: timer: Replace bss variable by gd
arm926ejs: timer: Replace bss variable by gdr
Jens Scharsig (1):
remove (double) LED initialization in arm920t start.s
Liu Hui-R64343 (10):
MX51EVK: UART does not print out the early information
MX5: Add initial support for MX53 processor
fec_mxc: add support for MX53 processor
serial_mxc: add support for MX53 processor
mxc_gpio: add support for MX53 processor
mxc_i2c: add support for MX53 processor
fsl_pmic: add I2C interface support
MX5:MX53: add initial support for MX53EVK board
imximage: Add MX53 boot image support
ARM: */start.S: code cleanup
Marek Vasut (4):
BLOCK: Add freescale IMX51 PATA driver
MC13892: Add SWx buck switchers definitions
MX51EVK: Use SWx macros in PMIC init
iMX5: EfikaMX: Preliminary board support
Mike Rapoport (1):
OMAP3: add CM-T35 board
Minkyu Kang (4):
armv7: s5pc1xx: don't use function pointer for clock functions
S5P: serial: Use the inline function instead of static value
armv7: add support for S5PC210 SoC
armv7: add support for s5pc210 universal board
Po-Yu Chuang (1):
arm: a320evb: fixes for relocation support
Sandeep Paulraj (12):
Davinci MMCSD Support
DaVinci DM355: Adding MMC/SD support for DM355 EVM
DaVinci DM365: Adding MMC/SD support for DM365 EVM
DM365: Fix Build Error
DaVinci EMAC: Fix davinci_eth_gigabit_enable
DaVinci EMAC: Add name to Ethernet device
DaVinci DM6467: Added ET1011C (LSI) PHY support
ARM: Update mach types
DaVinci DM6467: Enhance board Support
DaVinci DM6467: Fix Build Error
DaVinci Sonata: Fix Build Error
DaVinci: Remove incorrect CONFIG option
Stefano Babic (13):
mxc_nand: add support for i.MX35 processor
Add support for MX35 processor
serial_mxc: add support for Freescale's i.MX35 processor
mxc_i2c: Add support for the i.MX35 processor
I2C: mxc_i2c: get rid of __REG access
I2C: mxc_i2c: address failure with mx35 processor
Add basic support for Freescale's mc9sdz60
SPI: mxc_spi: add support for i.MX35 processor
SPI: mxc_spi: replace fixed offsets with structures
Add support for Freescale's mx35pdk board.
MX5: Reuse the gd->tbl value for timestamp and add gd->lastinc
for lastinc bss
MXC: removed warnings from IMX51 ATA driver
ARM: fix broken build of ARM
MAINTAINERS | 17 +-
arch/arm/config.mk | 2 +-
arch/arm/cpu/arm1136/mx31/timer.c | 19 +-
arch/arm/cpu/arm1136/mx35/Makefile | 63 +
arch/arm/cpu/arm1136/mx35/asm-offsets.c | 43 +
arch/arm/cpu/arm1136/mx35/generic.c | 463 ++++
arch/arm/cpu/arm1136/mx35/iomux.c | 116 +
arch/arm/cpu/arm1136/mx35/timer.c | 120 +
arch/arm/cpu/arm1136/omap24xx/timer.c | 19 +-
arch/arm/cpu/arm1136/start.S | 2 -
arch/arm/cpu/arm1176/start.S | 2 -
arch/arm/cpu/arm720t/start.S | 2 -
arch/arm/cpu/arm920t/start.S | 5 -
arch/arm/cpu/arm925t/start.S | 2 -
arch/arm/cpu/arm926ejs/davinci/Makefile | 2 +-
arch/arm/cpu/arm926ejs/davinci/cpu.c | 14 +-
arch/arm/cpu/arm926ejs/davinci/et1011c.c | 55 +
arch/arm/cpu/arm926ejs/kirkwood/timer.c | 6 +-
arch/arm/cpu/arm926ejs/mb86r0x/timer.c | 6 +-
arch/arm/cpu/arm926ejs/mx25/timer.c | 6 +-
arch/arm/cpu/arm926ejs/mx27/timer.c | 6 +-
arch/arm/cpu/arm926ejs/omap/timer.c | 6 +-
arch/arm/cpu/arm926ejs/orion5x/timer.c | 6 +-
arch/arm/cpu/arm926ejs/spear/timer.c | 6 +-
arch/arm/cpu/arm926ejs/start.S | 2 -
arch/arm/cpu/arm926ejs/versatile/timer.c | 6 +-
arch/arm/cpu/arm946es/start.S | 2 -
arch/arm/cpu/arm_intcm/start.S | 2 -
arch/arm/cpu/armv7/mx5/iomux.c | 30 +-
arch/arm/cpu/armv7/mx5/lowlevel_init.S | 91 +-
arch/arm/cpu/armv7/mx5/soc.c | 22 +-
arch/arm/cpu/armv7/mx5/timer.c | 6 +-
arch/arm/cpu/armv7/s5p-common/cpu_info.c | 2 -
arch/arm/cpu/armv7/s5pc1xx/clock.c | 38 +-
.../arm/cpu/armv7/s5pc2xx/Makefile | 37 +-
arch/arm/cpu/armv7/s5pc2xx/clock.c | 220 ++
arch/arm/cpu/armv7/s5pc2xx/soc.c | 30 +
arch/arm/cpu/armv7/start.S | 2 -
arch/arm/cpu/ixp/start.S | 2 -
arch/arm/cpu/lh7a40x/start.S | 2 -
arch/arm/cpu/pxa/start.S | 2 -
arch/arm/cpu/s3c44b0/start.S | 2 -
arch/arm/cpu/sa1100/start.S | 2 -
arch/arm/include/asm/arch-davinci/emac_defs.h | 3 +
arch/arm/include/asm/arch-davinci/hardware.h | 1 +
arch/arm/include/asm/arch-davinci/sdmmc_defs.h | 175 ++
arch/arm/include/asm/arch-mx31/mx31-regs.h | 11 +
arch/arm/include/asm/arch-mx35/clock.h | 45 +
arch/arm/include/asm/arch-mx35/crm_regs.h | 270 +++
arch/arm/include/asm/arch-mx35/imx-regs.h | 303 +++
arch/arm/include/asm/arch-mx35/iomux.h | 295 +++
arch/arm/include/asm/arch-mx35/mx35_pins.h | 355 +++
arch/arm/include/asm/arch-mx35/sys_proto.h | 31 +
arch/arm/include/asm/arch-mx5/asm-offsets.h | 5 +
arch/arm/include/asm/arch-mx5/imx-regs.h | 94 +-
arch/arm/include/asm/arch-mx5/iomux.h | 102 -
arch/arm/include/asm/arch-mx5/mx5x_pins.h | 469 ++++-
arch/arm/include/asm/arch-s5pc1xx/clk.h | 10 +-
arch/arm/include/asm/arch-s5pc1xx/uart.h | 5 +-
arch/arm/include/asm/arch-s5pc2xx/adc.h | 42 +
arch/arm/include/asm/arch-s5pc2xx/clk.h | 36 +
arch/arm/include/asm/arch-s5pc2xx/clock.h | 255 +++
arch/arm/include/asm/arch-s5pc2xx/cpu.h | 103 +
arch/arm/include/asm/arch-s5pc2xx/gpio.h | 112 +
arch/arm/include/asm/arch-s5pc2xx/mmc.h | 71 +
arch/arm/include/asm/arch-s5pc2xx/pwm.h | 55 +
arch/arm/include/asm/arch-s5pc2xx/sys_proto.h | 32 +
arch/arm/include/asm/arch-s5pc2xx/uart.h | 58 +
arch/arm/include/asm/io.h | 32 +-
arch/arm/include/asm/mach-types.h | 2305
+++++++++++++++++++-
.../{faraday/a320evb/config.mk => cm_t35/Makefile} | 42 +-
board/cm_t35/cm_t35.c | 371 ++++
board/davinci/common/misc.c | 2 +-
board/davinci/dm355evm/dm355evm.c | 41 +
board/davinci/dm365evm/dm365evm.c | 49 +
board/davinci/dm6467evm/dm6467evm.c | 26 +
board/efikamx/Makefile | 52 +
board/{faraday/a320evb => efikamx}/config.mk | 24 +-
board/efikamx/efikamx.c | 689 ++++++
board/efikamx/imximage.cfg | 122 +
board/faraday/a320evb/a320evb.c | 3 +-
board/freescale/mx35pdk/Makefile | 49 +
board/freescale/mx35pdk/lowlevel_init.S | 363 +++
board/freescale/mx35pdk/mx35pdk.c | 297 +++
board/freescale/mx35pdk/mx35pdk.h | 101 +
board/freescale/mx51evk/mx51evk.c | 17 +-
.../config.mk => freescale/mx53evk/Makefile} | 43 +-
.../a320evb => freescale/mx53evk}/config.mk | 23 +-
board/freescale/mx53evk/imximage.cfg | 112 +
board/freescale/mx53evk/mx53evk.c | 397 ++++
board/samsung/universal_c210/Makefile | 51 +
board/samsung/universal_c210/lowlevel_init.S | 395 ++++
board/samsung/universal_c210/onenand.c | 34 +
board/samsung/universal_c210/universal.c | 250 +++
boards.cfg | 5 +
doc/README.imximage | 12 +-
doc/README.mx35pdk | 188 ++
doc/README.omap3 | 16 +-
drivers/block/Makefile | 1 +
drivers/block/mxc_ata.c | 146 ++
drivers/gpio/mxc_gpio.c | 9 +-
drivers/i2c/mxc_i2c.c | 172 ++-
drivers/misc/Makefile | 5 +-
drivers/misc/fsl_pmic.c | 45 +-
drivers/misc/mc9sdz60.c | 51 +
drivers/mmc/Makefile | 1 +
drivers/mmc/davinci_mmc.c | 404 ++++
drivers/mtd/nand/mxc_nand.c | 6 +-
drivers/net/davinci_emac.c | 15 +-
drivers/net/fec_mxc.c | 2 +-
drivers/net/fec_mxc.h | 4 +-
drivers/serial/serial_mxc.c | 9 +-
drivers/serial/serial_s5p.c | 2 +-
drivers/spi/mxc_spi.c | 200 +-
include/configs/a320evb.h | 14 +-
include/configs/cm_t35.h | 352 +++
include/configs/davinci_dm355evm.h | 22 +
include/configs/davinci_dm365evm.h | 22 +
include/configs/davinci_dm6467evm.h | 30 +-
include/configs/davinci_sonata.h | 1 +
include/configs/efikamx.h | 232 ++
include/configs/mx35pdk.h | 303 +++
include/configs/mx51evk.h | 5 +-
include/configs/mx53evk.h | 193 ++
include/configs/s5pc210_universal.h | 244 +++
include/configs/vision2.h | 3 +-
include/mc13892.h | 44 +
include/mc9sdz60.h | 84 +
include/mmc.h | 3 +
include/netdev.h | 1 +
tools/imximage.c | 525 ++++--
tools/imximage.h | 110 +-
132 files changed, 13054 insertions(+), 743 deletions(-)
create mode 100644 arch/arm/cpu/arm1136/mx35/Makefile
create mode 100644 arch/arm/cpu/arm1136/mx35/asm-offsets.c
create mode 100644 arch/arm/cpu/arm1136/mx35/generic.c
create mode 100644 arch/arm/cpu/arm1136/mx35/iomux.c
create mode 100644 arch/arm/cpu/arm1136/mx35/timer.c
create mode 100644 arch/arm/cpu/arm926ejs/davinci/et1011c.c
copy board/faraday/a320evb/config.mk =>
arch/arm/cpu/armv7/s5pc2xx/Makefile (56%)
create mode 100644 arch/arm/cpu/armv7/s5pc2xx/clock.c
create mode 100644 arch/arm/cpu/armv7/s5pc2xx/soc.c
create mode 100644 arch/arm/include/asm/arch-davinci/sdmmc_defs.h
create mode 100644 arch/arm/include/asm/arch-mx35/clock.h
create mode 100644 arch/arm/include/asm/arch-mx35/crm_regs.h
create mode 100644 arch/arm/include/asm/arch-mx35/imx-regs.h
create mode 100644 arch/arm/include/asm/arch-mx35/iomux.h
create mode 100644 arch/arm/include/asm/arch-mx35/mx35_pins.h
create mode 100644 arch/arm/include/asm/arch-mx35/sys_proto.h
create mode 100644 arch/arm/include/asm/arch-s5pc2xx/adc.h
create mode 100644 arch/arm/include/asm/arch-s5pc2xx/clk.h
create mode 100644 arch/arm/include/asm/arch-s5pc2xx/clock.h
create mode 100644 arch/arm/include/asm/arch-s5pc2xx/cpu.h
create mode 100644 arch/arm/include/asm/arch-s5pc2xx/gpio.h
create mode 100644 arch/arm/include/asm/arch-s5pc2xx/mmc.h
create mode 100644 arch/arm/include/asm/arch-s5pc2xx/pwm.h
create mode 100644 arch/arm/include/asm/arch-s5pc2xx/sys_proto.h
create mode 100644 arch/arm/include/asm/arch-s5pc2xx/uart.h
copy board/{faraday/a320evb/config.mk => cm_t35/Makefile} (54%)
create mode 100644 board/cm_t35/cm_t35.c
create mode 100644 board/efikamx/Makefile
copy board/{faraday/a320evb => efikamx}/config.mk (62%)
create mode 100644 board/efikamx/efikamx.c
create mode 100644 board/efikamx/imximage.cfg
create mode 100644 board/freescale/mx35pdk/Makefile
create mode 100644 board/freescale/mx35pdk/lowlevel_init.S
create mode 100644 board/freescale/mx35pdk/mx35pdk.c
create mode 100644 board/freescale/mx35pdk/mx35pdk.h
copy board/{faraday/a320evb/config.mk => freescale/mx53evk/Makefile} (50%)
rename board/{faraday/a320evb => freescale/mx53evk}/config.mk (62%)
create mode 100644 board/freescale/mx53evk/imximage.cfg
create mode 100644 board/freescale/mx53evk/mx53evk.c
create mode 100644 board/samsung/universal_c210/Makefile
create mode 100644 board/samsung/universal_c210/lowlevel_init.S
create mode 100644 board/samsung/universal_c210/onenand.c
create mode 100644 board/samsung/universal_c210/universal.c
create mode 100644 doc/README.mx35pdk
create mode 100644 drivers/block/mxc_ata.c
create mode 100644 drivers/misc/mc9sdz60.c
create mode 100644 drivers/mmc/davinci_mmc.c
create mode 100644 include/configs/cm_t35.h
create mode 100644 include/configs/efikamx.h
create mode 100644 include/configs/mx35pdk.h
create mode 100644 include/configs/mx53evk.h
create mode 100644 include/configs/s5pc210_universal.h
create mode 100644 include/mc9sdz60.h
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 40+ messages in thread* [U-Boot] Pull request: u-boot-arm
2011-02-02 0:09 Albert ARIBAUD
@ 2011-02-02 20:57 ` Wolfgang Denk
0 siblings, 0 replies; 40+ messages in thread
From: Wolfgang Denk @ 2011-02-02 20:57 UTC (permalink / raw)
To: u-boot
Dear Albert ARIBAUD,
In message <4D48A0A0.8040904@free.fr> you wrote:
> Hi Wolfgang,
>
> Please pull from u-boot-arm/master to go into rc1 of upcoming release.
>
> The following changes since commit 6f918bd46482f889f4d94623b09daf659a1974bd:
>
> Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx (2011-01-31
> 23:20:32 +0100)
>
> are available in the git repository at:
>
> git://www.denx.de/git/u-boot-arm.git master
>
> Alexander Holler (1):
> ARM: Avoid compiler optimization for readb, writeb and friends.
>
> Anatolij Gustschin (2):
> SPI: mxc_spi: fix swapping bug and add missing swapping in
> unaligned rx case
> SPI: mxc_spi: add SPI clock calculation and setup to the driver
>
> Heiko Schocher (2):
> arm1136: timer: Replace bss variable by gd
> arm926ejs: timer: Replace bss variable by gdr
>
> Jens Scharsig (1):
> remove (double) LED initialization in arm920t start.s
>
> Liu Hui-R64343 (10):
> MX51EVK: UART does not print out the early information
> MX5: Add initial support for MX53 processor
> fec_mxc: add support for MX53 processor
> serial_mxc: add support for MX53 processor
> mxc_gpio: add support for MX53 processor
> mxc_i2c: add support for MX53 processor
> fsl_pmic: add I2C interface support
> MX5:MX53: add initial support for MX53EVK board
> imximage: Add MX53 boot image support
> ARM: */start.S: code cleanup
>
> Marek Vasut (4):
> BLOCK: Add freescale IMX51 PATA driver
> MC13892: Add SWx buck switchers definitions
> MX51EVK: Use SWx macros in PMIC init
> iMX5: EfikaMX: Preliminary board support
>
> Mike Rapoport (1):
> OMAP3: add CM-T35 board
>
> Minkyu Kang (4):
> armv7: s5pc1xx: don't use function pointer for clock functions
> S5P: serial: Use the inline function instead of static value
> armv7: add support for S5PC210 SoC
> armv7: add support for s5pc210 universal board
>
> Po-Yu Chuang (1):
> arm: a320evb: fixes for relocation support
>
> Sandeep Paulraj (12):
> Davinci MMCSD Support
> DaVinci DM355: Adding MMC/SD support for DM355 EVM
> DaVinci DM365: Adding MMC/SD support for DM365 EVM
> DM365: Fix Build Error
> DaVinci EMAC: Fix davinci_eth_gigabit_enable
> DaVinci EMAC: Add name to Ethernet device
> DaVinci DM6467: Added ET1011C (LSI) PHY support
> ARM: Update mach types
> DaVinci DM6467: Enhance board Support
> DaVinci DM6467: Fix Build Error
> DaVinci Sonata: Fix Build Error
> DaVinci: Remove incorrect CONFIG option
>
> Stefano Babic (13):
> mxc_nand: add support for i.MX35 processor
> Add support for MX35 processor
> serial_mxc: add support for Freescale's i.MX35 processor
> mxc_i2c: Add support for the i.MX35 processor
> I2C: mxc_i2c: get rid of __REG access
> I2C: mxc_i2c: address failure with mx35 processor
> Add basic support for Freescale's mc9sdz60
> SPI: mxc_spi: add support for i.MX35 processor
> SPI: mxc_spi: replace fixed offsets with structures
> Add support for Freescale's mx35pdk board.
> MX5: Reuse the gd->tbl value for timestamp and add gd->lastinc
> for lastinc bss
> MXC: removed warnings from IMX51 ATA driver
> ARM: fix broken build of ARM
>
> MAINTAINERS | 17 +-
> arch/arm/config.mk | 2 +-
> arch/arm/cpu/arm1136/mx31/timer.c | 19 +-
> arch/arm/cpu/arm1136/mx35/Makefile | 63 +
> arch/arm/cpu/arm1136/mx35/asm-offsets.c | 43 +
> arch/arm/cpu/arm1136/mx35/generic.c | 463 ++++
> arch/arm/cpu/arm1136/mx35/iomux.c | 116 +
> arch/arm/cpu/arm1136/mx35/timer.c | 120 +
> arch/arm/cpu/arm1136/omap24xx/timer.c | 19 +-
> arch/arm/cpu/arm1136/start.S | 2 -
> arch/arm/cpu/arm1176/start.S | 2 -
> arch/arm/cpu/arm720t/start.S | 2 -
> arch/arm/cpu/arm920t/start.S | 5 -
> arch/arm/cpu/arm925t/start.S | 2 -
> arch/arm/cpu/arm926ejs/davinci/Makefile | 2 +-
> arch/arm/cpu/arm926ejs/davinci/cpu.c | 14 +-
> arch/arm/cpu/arm926ejs/davinci/et1011c.c | 55 +
> arch/arm/cpu/arm926ejs/kirkwood/timer.c | 6 +-
> arch/arm/cpu/arm926ejs/mb86r0x/timer.c | 6 +-
> arch/arm/cpu/arm926ejs/mx25/timer.c | 6 +-
> arch/arm/cpu/arm926ejs/mx27/timer.c | 6 +-
> arch/arm/cpu/arm926ejs/omap/timer.c | 6 +-
> arch/arm/cpu/arm926ejs/orion5x/timer.c | 6 +-
> arch/arm/cpu/arm926ejs/spear/timer.c | 6 +-
> arch/arm/cpu/arm926ejs/start.S | 2 -
> arch/arm/cpu/arm926ejs/versatile/timer.c | 6 +-
> arch/arm/cpu/arm946es/start.S | 2 -
> arch/arm/cpu/arm_intcm/start.S | 2 -
> arch/arm/cpu/armv7/mx5/iomux.c | 30 +-
> arch/arm/cpu/armv7/mx5/lowlevel_init.S | 91 +-
> arch/arm/cpu/armv7/mx5/soc.c | 22 +-
> arch/arm/cpu/armv7/mx5/timer.c | 6 +-
> arch/arm/cpu/armv7/s5p-common/cpu_info.c | 2 -
> arch/arm/cpu/armv7/s5pc1xx/clock.c | 38 +-
> .../arm/cpu/armv7/s5pc2xx/Makefile | 37 +-
> arch/arm/cpu/armv7/s5pc2xx/clock.c | 220 ++
> arch/arm/cpu/armv7/s5pc2xx/soc.c | 30 +
> arch/arm/cpu/armv7/start.S | 2 -
> arch/arm/cpu/ixp/start.S | 2 -
> arch/arm/cpu/lh7a40x/start.S | 2 -
> arch/arm/cpu/pxa/start.S | 2 -
> arch/arm/cpu/s3c44b0/start.S | 2 -
> arch/arm/cpu/sa1100/start.S | 2 -
> arch/arm/include/asm/arch-davinci/emac_defs.h | 3 +
> arch/arm/include/asm/arch-davinci/hardware.h | 1 +
> arch/arm/include/asm/arch-davinci/sdmmc_defs.h | 175 ++
> arch/arm/include/asm/arch-mx31/mx31-regs.h | 11 +
> arch/arm/include/asm/arch-mx35/clock.h | 45 +
> arch/arm/include/asm/arch-mx35/crm_regs.h | 270 +++
> arch/arm/include/asm/arch-mx35/imx-regs.h | 303 +++
> arch/arm/include/asm/arch-mx35/iomux.h | 295 +++
> arch/arm/include/asm/arch-mx35/mx35_pins.h | 355 +++
> arch/arm/include/asm/arch-mx35/sys_proto.h | 31 +
> arch/arm/include/asm/arch-mx5/asm-offsets.h | 5 +
> arch/arm/include/asm/arch-mx5/imx-regs.h | 94 +-
> arch/arm/include/asm/arch-mx5/iomux.h | 102 -
> arch/arm/include/asm/arch-mx5/mx5x_pins.h | 469 ++++-
> arch/arm/include/asm/arch-s5pc1xx/clk.h | 10 +-
> arch/arm/include/asm/arch-s5pc1xx/uart.h | 5 +-
> arch/arm/include/asm/arch-s5pc2xx/adc.h | 42 +
> arch/arm/include/asm/arch-s5pc2xx/clk.h | 36 +
> arch/arm/include/asm/arch-s5pc2xx/clock.h | 255 +++
> arch/arm/include/asm/arch-s5pc2xx/cpu.h | 103 +
> arch/arm/include/asm/arch-s5pc2xx/gpio.h | 112 +
> arch/arm/include/asm/arch-s5pc2xx/mmc.h | 71 +
> arch/arm/include/asm/arch-s5pc2xx/pwm.h | 55 +
> arch/arm/include/asm/arch-s5pc2xx/sys_proto.h | 32 +
> arch/arm/include/asm/arch-s5pc2xx/uart.h | 58 +
> arch/arm/include/asm/io.h | 32 +-
> arch/arm/include/asm/mach-types.h | 2305
> +++++++++++++++++++-
> .../{faraday/a320evb/config.mk => cm_t35/Makefile} | 42 +-
> board/cm_t35/cm_t35.c | 371 ++++
> board/davinci/common/misc.c | 2 +-
> board/davinci/dm355evm/dm355evm.c | 41 +
> board/davinci/dm365evm/dm365evm.c | 49 +
> board/davinci/dm6467evm/dm6467evm.c | 26 +
> board/efikamx/Makefile | 52 +
> board/{faraday/a320evb => efikamx}/config.mk | 24 +-
> board/efikamx/efikamx.c | 689 ++++++
> board/efikamx/imximage.cfg | 122 +
> board/faraday/a320evb/a320evb.c | 3 +-
> board/freescale/mx35pdk/Makefile | 49 +
> board/freescale/mx35pdk/lowlevel_init.S | 363 +++
> board/freescale/mx35pdk/mx35pdk.c | 297 +++
> board/freescale/mx35pdk/mx35pdk.h | 101 +
> board/freescale/mx51evk/mx51evk.c | 17 +-
> .../config.mk => freescale/mx53evk/Makefile} | 43 +-
> .../a320evb => freescale/mx53evk}/config.mk | 23 +-
> board/freescale/mx53evk/imximage.cfg | 112 +
> board/freescale/mx53evk/mx53evk.c | 397 ++++
> board/samsung/universal_c210/Makefile | 51 +
> board/samsung/universal_c210/lowlevel_init.S | 395 ++++
> board/samsung/universal_c210/onenand.c | 34 +
> board/samsung/universal_c210/universal.c | 250 +++
> boards.cfg | 5 +
> doc/README.imximage | 12 +-
> doc/README.mx35pdk | 188 ++
> doc/README.omap3 | 16 +-
> drivers/block/Makefile | 1 +
> drivers/block/mxc_ata.c | 146 ++
> drivers/gpio/mxc_gpio.c | 9 +-
> drivers/i2c/mxc_i2c.c | 172 ++-
> drivers/misc/Makefile | 5 +-
> drivers/misc/fsl_pmic.c | 45 +-
> drivers/misc/mc9sdz60.c | 51 +
> drivers/mmc/Makefile | 1 +
> drivers/mmc/davinci_mmc.c | 404 ++++
> drivers/mtd/nand/mxc_nand.c | 6 +-
> drivers/net/davinci_emac.c | 15 +-
> drivers/net/fec_mxc.c | 2 +-
> drivers/net/fec_mxc.h | 4 +-
> drivers/serial/serial_mxc.c | 9 +-
> drivers/serial/serial_s5p.c | 2 +-
> drivers/spi/mxc_spi.c | 200 +-
> include/configs/a320evb.h | 14 +-
> include/configs/cm_t35.h | 352 +++
> include/configs/davinci_dm355evm.h | 22 +
> include/configs/davinci_dm365evm.h | 22 +
> include/configs/davinci_dm6467evm.h | 30 +-
> include/configs/davinci_sonata.h | 1 +
> include/configs/efikamx.h | 232 ++
> include/configs/mx35pdk.h | 303 +++
> include/configs/mx51evk.h | 5 +-
> include/configs/mx53evk.h | 193 ++
> include/configs/s5pc210_universal.h | 244 +++
> include/configs/vision2.h | 3 +-
> include/mc13892.h | 44 +
> include/mc9sdz60.h | 84 +
> include/mmc.h | 3 +
> include/netdev.h | 1 +
> tools/imximage.c | 525 ++++--
> tools/imximage.h | 110 +-
> 132 files changed, 13054 insertions(+), 743 deletions(-)
> create mode 100644 arch/arm/cpu/arm1136/mx35/Makefile
> create mode 100644 arch/arm/cpu/arm1136/mx35/asm-offsets.c
> create mode 100644 arch/arm/cpu/arm1136/mx35/generic.c
> create mode 100644 arch/arm/cpu/arm1136/mx35/iomux.c
> create mode 100644 arch/arm/cpu/arm1136/mx35/timer.c
> create mode 100644 arch/arm/cpu/arm926ejs/davinci/et1011c.c
> copy board/faraday/a320evb/config.mk =>
> arch/arm/cpu/armv7/s5pc2xx/Makefile (56%)
> create mode 100644 arch/arm/cpu/armv7/s5pc2xx/clock.c
> create mode 100644 arch/arm/cpu/armv7/s5pc2xx/soc.c
> create mode 100644 arch/arm/include/asm/arch-davinci/sdmmc_defs.h
> create mode 100644 arch/arm/include/asm/arch-mx35/clock.h
> create mode 100644 arch/arm/include/asm/arch-mx35/crm_regs.h
> create mode 100644 arch/arm/include/asm/arch-mx35/imx-regs.h
> create mode 100644 arch/arm/include/asm/arch-mx35/iomux.h
> create mode 100644 arch/arm/include/asm/arch-mx35/mx35_pins.h
> create mode 100644 arch/arm/include/asm/arch-mx35/sys_proto.h
> create mode 100644 arch/arm/include/asm/arch-s5pc2xx/adc.h
> create mode 100644 arch/arm/include/asm/arch-s5pc2xx/clk.h
> create mode 100644 arch/arm/include/asm/arch-s5pc2xx/clock.h
> create mode 100644 arch/arm/include/asm/arch-s5pc2xx/cpu.h
> create mode 100644 arch/arm/include/asm/arch-s5pc2xx/gpio.h
> create mode 100644 arch/arm/include/asm/arch-s5pc2xx/mmc.h
> create mode 100644 arch/arm/include/asm/arch-s5pc2xx/pwm.h
> create mode 100644 arch/arm/include/asm/arch-s5pc2xx/sys_proto.h
> create mode 100644 arch/arm/include/asm/arch-s5pc2xx/uart.h
> copy board/{faraday/a320evb/config.mk => cm_t35/Makefile} (54%)
> create mode 100644 board/cm_t35/cm_t35.c
> create mode 100644 board/efikamx/Makefile
> copy board/{faraday/a320evb => efikamx}/config.mk (62%)
> create mode 100644 board/efikamx/efikamx.c
> create mode 100644 board/efikamx/imximage.cfg
> create mode 100644 board/freescale/mx35pdk/Makefile
> create mode 100644 board/freescale/mx35pdk/lowlevel_init.S
> create mode 100644 board/freescale/mx35pdk/mx35pdk.c
> create mode 100644 board/freescale/mx35pdk/mx35pdk.h
> copy board/{faraday/a320evb/config.mk => freescale/mx53evk/Makefile} (50%)
> rename board/{faraday/a320evb => freescale/mx53evk}/config.mk (62%)
> create mode 100644 board/freescale/mx53evk/imximage.cfg
> create mode 100644 board/freescale/mx53evk/mx53evk.c
> create mode 100644 board/samsung/universal_c210/Makefile
> create mode 100644 board/samsung/universal_c210/lowlevel_init.S
> create mode 100644 board/samsung/universal_c210/onenand.c
> create mode 100644 board/samsung/universal_c210/universal.c
> create mode 100644 doc/README.mx35pdk
> create mode 100644 drivers/block/mxc_ata.c
> create mode 100644 drivers/misc/mc9sdz60.c
> create mode 100644 drivers/mmc/davinci_mmc.c
> create mode 100644 include/configs/cm_t35.h
> create mode 100644 include/configs/efikamx.h
> create mode 100644 include/configs/mx35pdk.h
> create mode 100644 include/configs/mx53evk.h
> create mode 100644 include/configs/s5pc210_universal.h
> create mode 100644 include/mc9sdz60.h
Applied, thanks.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
One of the advantages of being a captain is being able to ask for ad-
vice without necessarily having to take it.
-- Kirk, "Dagger of the Mind", stardate 2715.2
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
@ 2010-11-26 20:29 Wolfgang Denk
2010-11-26 20:55 ` Wolfgang Denk
0 siblings, 1 reply; 40+ messages in thread
From: Wolfgang Denk @ 2010-11-26 20:29 UTC (permalink / raw)
To: u-boot
The following changes since commit 6163f5b4c8873848ed023054bc401727301ea537:
malloc: Fix issue with calloc memory possibly being non-zero (2010-11-17 22:06:40 +0100)
are available in the git repository at:
git://git.denx.de/u-boot-arm.git master
Albert Aribaud (2):
arm: add ELF relocation support to rest of cpus
arm1176: bugfix: fix start.S for ELF relocation
Eric Cooper (1):
Seagate FreeAgent DockStar support
Grazvydas Ignotas (3):
OMAP3: pandora: fix relocation and init memory
OMAP3: remove unused config macros
OMAP3: pandora: update config for production
Matthias Weisser (1):
Makefile: Fix build with USE_PRIVATE_LIBGCC
Nick Thompson (1):
da830: fixup ARM relocation support
Nishanth Menon (2):
mmc: omap: timeout counter fix
omap4: board: change global data pointer to file scope
Sekhar Nori (2):
DA850 EVM: add information regarding DA850 in README.davinci
DA850 EVM: passing maximum clock rate information to kernel
Steve Sakoman (1):
OMAP4: Panda: Disable CMD_NFS
Wolfgang Denk (1):
DaVinci: remove bogus DEF_BOOTM definition
MAINTAINERS | 4 +
Makefile | 2 +-
arch/arm/cpu/arm1176/start.S | 47 +++-------
arch/arm/cpu/arm720t/start.S | 119 ++++++++++++-----------
arch/arm/cpu/arm720t/u-boot.lds | 39 +++++---
arch/arm/cpu/arm920t/start.S | 125 +++++++++++++------------
arch/arm/cpu/arm920t/u-boot.lds | 38 +++++---
arch/arm/cpu/arm925t/start.S | 127 +++++++++++++------------
arch/arm/cpu/arm925t/u-boot.lds | 38 +++++---
arch/arm/cpu/arm946es/start.S | 123 ++++++++++++-----------
arch/arm/cpu/arm946es/u-boot.lds | 38 +++++---
arch/arm/cpu/arm_intcm/start.S | 127 +++++++++++++-----------
arch/arm/cpu/arm_intcm/u-boot.lds | 38 +++++---
arch/arm/cpu/armv7/omap4/board.c | 3 +-
arch/arm/cpu/ixp/start.S | 118 ++++++++++++-----------
arch/arm/cpu/ixp/u-boot.lds | 38 +++++---
arch/arm/cpu/lh7a40x/start.S | 119 ++++++++++++-----------
arch/arm/cpu/lh7a40x/u-boot.lds | 38 +++++---
arch/arm/cpu/s3c44b0/start.S | 131 ++++++++++++--------------
arch/arm/cpu/s3c44b0/u-boot.lds | 38 +++++---
arch/arm/cpu/sa1100/start.S | 119 ++++++++++++-----------
arch/arm/cpu/sa1100/u-boot.lds | 38 +++++---
board/Seagate/dockstar/Makefile | 54 +++++++++++
board/Seagate/dockstar/dockstar.c | 181 +++++++++++++++++++++++++++++++++++
board/Seagate/dockstar/dockstar.h | 44 +++++++++
board/Seagate/dockstar/kwbimage.cfg | 165 +++++++++++++++++++++++++++++++
board/davinci/da8xxevm/da850evm.c | 33 +++++++
board/pandora/config.mk | 33 -------
boards.cfg | 1 +
doc/README.davinci | 25 +++++
drivers/mmc/omap_hsmmc.c | 107 ++++++++++++++++-----
include/configs/da830evm.h | 11 ++-
include/configs/da850evm.h | 2 +-
include/configs/davinci_dvevm.h | 1 -
include/configs/davinci_sonata.h | 1 -
include/configs/dockstar.h | 125 ++++++++++++++++++++++++
include/configs/omap3_beagle.h | 18 ----
include/configs/omap3_evm.h | 18 ----
include/configs/omap3_overo.h | 18 ----
include/configs/omap3_pandora.h | 117 ++++++++++-------------
include/configs/omap3_sdp3430.h | 7 --
include/configs/omap3_zoom1.h | 18 ----
include/configs/omap3_zoom2.h | 10 --
include/configs/omap4_panda.h | 1 +
include/configs/tnetv107x_evm.h | 1 -
45 files changed, 1577 insertions(+), 921 deletions(-)
create mode 100644 board/Seagate/dockstar/Makefile
create mode 100644 board/Seagate/dockstar/dockstar.c
create mode 100644 board/Seagate/dockstar/dockstar.h
create mode 100644 board/Seagate/dockstar/kwbimage.cfg
delete mode 100644 board/pandora/config.mk
create mode 100644 include/configs/dockstar.h
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Obviously, a man's judgement cannot be better than the information on
which he has based it. Give him the truth and he may still go wrong
when he has the chance to be right, but give him no news or present
him only with distorted and incomplete data, with ignorant, sloppy or
biased reporting, with propaganda and deliberate falsehoods, and you
destroy his whole reasoning processes, and make him something less
than a man. - Arthur Hays Sulzberger
^ permalink raw reply [flat|nested] 40+ messages in thread* [U-Boot] Pull request: u-boot-arm
2010-11-26 20:29 Wolfgang Denk
@ 2010-11-26 20:55 ` Wolfgang Denk
2010-11-27 7:43 ` Dirk Behme
0 siblings, 1 reply; 40+ messages in thread
From: Wolfgang Denk @ 2010-11-26 20:55 UTC (permalink / raw)
To: u-boot
In message <20101126202955.B087D11D94F7@gemini.denx.de> you wrote:
> The following changes since commit 6163f5b4c8873848ed023054bc401727301ea537:
>
> malloc: Fix issue with calloc memory possibly being non-zero (2010-11-17 22:06:40 +0100)
>
> are available in the git repository at:
> git://git.denx.de/u-boot-arm.git master
>
> Albert Aribaud (2):
> arm: add ELF relocation support to rest of cpus
> arm1176: bugfix: fix start.S for ELF relocation
>
> Eric Cooper (1):
> Seagate FreeAgent DockStar support
>
> Grazvydas Ignotas (3):
> OMAP3: pandora: fix relocation and init memory
> OMAP3: remove unused config macros
> OMAP3: pandora: update config for production
>
> Matthias Weisser (1):
> Makefile: Fix build with USE_PRIVATE_LIBGCC
>
> Nick Thompson (1):
> da830: fixup ARM relocation support
>
> Nishanth Menon (2):
> mmc: omap: timeout counter fix
> omap4: board: change global data pointer to file scope
>
> Sekhar Nori (2):
> DA850 EVM: add information regarding DA850 in README.davinci
> DA850 EVM: passing maximum clock rate information to kernel
>
> Steve Sakoman (1):
> OMAP4: Panda: Disable CMD_NFS
>
> Wolfgang Denk (1):
> DaVinci: remove bogus DEF_BOOTM definition
>
> MAINTAINERS | 4 +
> Makefile | 2 +-
> arch/arm/cpu/arm1176/start.S | 47 +++-------
> arch/arm/cpu/arm720t/start.S | 119 ++++++++++++-----------
> arch/arm/cpu/arm720t/u-boot.lds | 39 +++++---
> arch/arm/cpu/arm920t/start.S | 125 +++++++++++++------------
> arch/arm/cpu/arm920t/u-boot.lds | 38 +++++---
> arch/arm/cpu/arm925t/start.S | 127 +++++++++++++------------
> arch/arm/cpu/arm925t/u-boot.lds | 38 +++++---
> arch/arm/cpu/arm946es/start.S | 123 ++++++++++++-----------
> arch/arm/cpu/arm946es/u-boot.lds | 38 +++++---
> arch/arm/cpu/arm_intcm/start.S | 127 +++++++++++++-----------
> arch/arm/cpu/arm_intcm/u-boot.lds | 38 +++++---
> arch/arm/cpu/armv7/omap4/board.c | 3 +-
> arch/arm/cpu/ixp/start.S | 118 ++++++++++++-----------
> arch/arm/cpu/ixp/u-boot.lds | 38 +++++---
> arch/arm/cpu/lh7a40x/start.S | 119 ++++++++++++-----------
> arch/arm/cpu/lh7a40x/u-boot.lds | 38 +++++---
> arch/arm/cpu/s3c44b0/start.S | 131 ++++++++++++--------------
> arch/arm/cpu/s3c44b0/u-boot.lds | 38 +++++---
> arch/arm/cpu/sa1100/start.S | 119 ++++++++++++-----------
> arch/arm/cpu/sa1100/u-boot.lds | 38 +++++---
> board/Seagate/dockstar/Makefile | 54 +++++++++++
> board/Seagate/dockstar/dockstar.c | 181 +++++++++++++++++++++++++++++++++++
> board/Seagate/dockstar/dockstar.h | 44 +++++++++
> board/Seagate/dockstar/kwbimage.cfg | 165 +++++++++++++++++++++++++++++++
> board/davinci/da8xxevm/da850evm.c | 33 +++++++
> board/pandora/config.mk | 33 -------
> boards.cfg | 1 +
> doc/README.davinci | 25 +++++
> drivers/mmc/omap_hsmmc.c | 107 ++++++++++++++++-----
> include/configs/da830evm.h | 11 ++-
> include/configs/da850evm.h | 2 +-
> include/configs/davinci_dvevm.h | 1 -
> include/configs/davinci_sonata.h | 1 -
> include/configs/dockstar.h | 125 ++++++++++++++++++++++++
> include/configs/omap3_beagle.h | 18 ----
> include/configs/omap3_evm.h | 18 ----
> include/configs/omap3_overo.h | 18 ----
> include/configs/omap3_pandora.h | 117 ++++++++++-------------
> include/configs/omap3_sdp3430.h | 7 --
> include/configs/omap3_zoom1.h | 18 ----
> include/configs/omap3_zoom2.h | 10 --
> include/configs/omap4_panda.h | 1 +
> include/configs/tnetv107x_evm.h | 1 -
> 45 files changed, 1577 insertions(+), 921 deletions(-)
> create mode 100644 board/Seagate/dockstar/Makefile
> create mode 100644 board/Seagate/dockstar/dockstar.c
> create mode 100644 board/Seagate/dockstar/dockstar.h
> create mode 100644 board/Seagate/dockstar/kwbimage.cfg
> delete mode 100644 board/pandora/config.mk
> create mode 100644 include/configs/dockstar.h
Applied.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
If at first you don't succeed, you are running about average.
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
2010-11-26 20:55 ` Wolfgang Denk
@ 2010-11-27 7:43 ` Dirk Behme
2010-11-27 9:06 ` Albert ARIBAUD
` (2 more replies)
0 siblings, 3 replies; 40+ messages in thread
From: Dirk Behme @ 2010-11-27 7:43 UTC (permalink / raw)
To: u-boot
On 26.11.2010 21:55, Wolfgang Denk wrote:
> In message<20101126202955.B087D11D94F7@gemini.denx.de> you wrote:
>> The following changes since commit 6163f5b4c8873848ed023054bc401727301ea537:
>>
>> malloc: Fix issue with calloc memory possibly being non-zero (2010-11-17 22:06:40 +0100)
>>
>> are available in the git repository at:
>> git://git.denx.de/u-boot-arm.git master
...
>
> Applied.
Doing a './MAKEALL ARMV7' on the recent master (d4752d5d2...) doesn't
look nice [2].
The following configs build fine:
igep0020
mx51evk
omap3_beagle
omap3_overo
omap3_pandora
omap4_panda
The following boards fail to build:
am3517_evm board
ca9x4_ct_vxp
devkit8000
igep0030
omap3_evm
omap3_sdp3430
omap3_zoom1
omap3_zoom2
omap4_sdp4430
s5p_goni
smdkc100
I applied [1] to fix a beagle warning.
Are there any other pending patches to fix the compilation of the
failing boards?
Thanks
Dirk
[1] http://patchwork.ozlabs.org/patch/72453/
[2] > ./MAKEALL ARMV7
Configuring for am3517_evm board...
board.c: In function '__dram_init_banksize':
board.c:233: error: 'CONFIG_SYS_SDRAM_BASE' undeclared (first use in
this function)
board.c:233: error: (Each undeclared identifier is reported only once
board.c:233: error: for each function it appears in.)
board.c: In function 'board_init_f':
board.c:279: error: 'CONFIG_SYS_INIT_SP_ADDR' undeclared (first use in
this function)
board.c:312: error: 'CONFIG_SYS_SDRAM_BASE' undeclared (first use in
this function)
make[1]: *** [board.o] Error 1
make: *** [arch/arm/lib/libarm.o] Error 2
size: './u-boot': No such file
Configuring for ca9x4_ct_vxp board...
syslib.c:26:32: error: asm/arch/sys_proto.h: No such file or directory
make[1]: *** No rule to build the target ?.depend?,
needed from ?_depend?. End.
syslib.c:26:32: error: asm/arch/sys_proto.h: No such file or directory
make[1]: *** [syslib.o] Error 1
make: *** [arch/arm/cpu/armv7/libarmv7.o] Error 2
size: './u-boot': No such file
Configuring for devkit8000 board...
start.S: Assembler messages:
start.S:144: Error: constant expression expected -- `ldr
sp,=((0x4020FFFC-CONFIG_SYS_GBL_DATA_SIZE))'
make[1]: *** [start.o] Error 1
make: *** [arch/arm/cpu/armv7/start.o] Error 2
size: './u-boot': No such file
Configuring for igep0020 board...
text data bss dec hex filename
219538 7768 214536 441842 6bdf2 ./u-boot
Configuring for igep0030 board...
net/libnet.o: In function `rpc_req':
u-boot.git/net/nfs.c:193: undefined reference to `NetEthHdrSize'
u-boot.git/net/nfs.c:202: undefined reference to `NetSendUDPPacket'
u-boot.git/net/nfs.c:203: undefined reference to `NetTxPacket'
u-boot.git/net/nfs.c:203: undefined reference to `NetServerEther'
net/libnet.o: In function `NfsStart':
u-boot.git/net/nfs.c:741: undefined reference to `NetSetTimeout'
u-boot.git/net/nfs.c:742: undefined reference to `NetSetHandler'
u-boot.git/net/nfs.c:754: undefined reference to `BootFile'
u-boot.git/net/nfs.c:754: undefined reference to `NetServerIP'
u-boot.git/net/nfs.c:754: undefined reference to `NetOurIP'
u-boot.git/net/nfs.c:754: undefined reference to `NetOurGatewayIP'
u-boot.git/net/nfs.c:754: undefined reference to `NetOurSubnetMask'
u-boot.git/net/nfs.c:754: undefined reference to `NetBootFileSize'
u-boot.git/net/nfs.c:754: undefined reference to `NetServerEther'
net/libnet.o: In function `nfs_read_reply':
u-boot.git/net/nfs.c:563: undefined reference to `NetBootFileXferSize'
net/libnet.o: In function `NfsHandler':
u-boot.git/net/nfs.c:656: undefined reference to `NetSetTimeout'
u-boot.git/net/nfs.c:668: undefined reference to `NetState'
net/libnet.o: In function `NfsTimeout':
u-boot.git/net/nfs.c:574: undefined reference to `NetStartAgain'
u-boot.git/net/nfs.c:577: undefined reference to `NetSetTimeout'
arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
2.19.51.20090205 assertion fail
/scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12273
arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
2.19.51.20090205 assertion fail
/scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12273
arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
2.19.51.20090205 assertion fail
/scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12273
arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
2.19.51.20090205 assertion fail
/scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12273
arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
2.19.51.20090205 assertion fail
/scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12273
arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
2.19.51.20090205 assertion fail
/scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12507
/bin/sh: line 1: 8055 Segmentation fault arm-none-linux-gnueabi-ld
-Bstatic -T u-boot.lds -pie -Ttext 0x80008000 $UNDEF_SYM
arch/arm/cpu/armv7/start.o --start-group lib/libgeneric.o
lib/lzma/liblzma.o lib/lzo/liblzo.o arch/arm/cpu/armv7/libarmv7.o
arch/arm/cpu/armv7/omap3/libomap3.o arch/arm/lib/libarm.o
fs/cramfs/libcramfs.o fs/fat/libfat.o fs/fdos/libfdos.o
fs/jffs2/libjffs2.o fs/reiserfs/libreiserfs.o fs/ext2/libext2fs.o
fs/yaffs2/libyaffs2.o fs/ubifs/libubifs.o net/libnet.o disk/libdisk.o
drivers/bios_emulator/libatibiosemu.o drivers/block/libblock.o
drivers/dma/libdma.o drivers/fpga/libfpga.o drivers/gpio/libgpio.o
drivers/hwmon/libhwmon.o drivers/i2c/libi2c.o drivers/input/libinput.o
drivers/misc/libmisc.o drivers/mmc/libmmc.o drivers/mtd/libmtd.o
drivers/mtd/nand/libnand.o drivers/mtd/onenand/libonenand.o
drivers/mtd/ubi/libubi.o drivers/mtd/spi/libspi_flash.o
drivers/net/libnet.o drivers/net/phy/libphy.o drivers/pci/libpci.o
drivers/pcmcia/libpcmcia.o drivers/power/libpower.o
drivers/spi/libspi.o drivers/rtc/librtc.o drivers/serial/libserial.o
drivers/twserial/libtws.o drivers/usb/gadget/libusb_gadget.o
drivers/usb/host/libusb_host.o drivers/usb/musb/libusb_musb.o
drivers/usb/phy/libusb_phy.o drivers/video/libvideo.o
drivers/watchdog/libwatchdog.o common/libcommon.o lib/libfdt/libfdt.o
api/libapi.o post/libpost.o
arch/arm/cpu/armv7/omap-common/libomap-common.o
board/isee/igep0030/libigep0030.o --end-group
u-boot.git/arch/arm/lib/eabi_compat.o -L
/opt/codesourcery/arm-none-linux-gnueabi/arm-2009q1/bin/../lib/gcc/arm-none-linux-gnueabi/4.3.3
-lgcc -Map u-boot.map -o u-boot
make: *** [u-boot] Error 139
size: ./u-boot: File format not recognized
Configuring for mx51evk board...
text data bss dec hex filename
159945 6504 216928 383377 5d991 ./u-boot
Configuring for omap3_beagle board...
text data bss dec hex filename
249978 11288 203700 464966 71846 ./u-boot
Configuring for omap3_overo board...
text data bss dec hex filename
216254 10836 210628 437718 6add6 ./u-boot
Configuring for omap3_evm board...
start.S: Assembler messages:
start.S:144: Error: constant expression expected -- `ldr
sp,=((0x4020FFFC-CONFIG_SYS_GBL_DATA_SIZE))'
make[1]: *** [start.o] Error 1
make: *** [arch/arm/cpu/armv7/start.o] Error 2
size: './u-boot': No such file
Configuring for omap3_pandora board...
text data bss dec hex filename
326528 10480 205116 542124 845ac ./u-boot
Configuring for omap3_sdp3430 board...
board.c: In function '__dram_init_banksize':
board.c:233: error: 'CONFIG_SYS_SDRAM_BASE' undeclared (first use in
this function)
board.c:233: error: (Each undeclared identifier is reported only once
board.c:233: error: for each function it appears in.)
board.c: In function 'board_init_f':
board.c:279: error: 'CONFIG_SYS_INIT_SP_ADDR' undeclared (first use in
this function)
board.c:312: error: 'CONFIG_SYS_SDRAM_BASE' undeclared (first use in
this function)
make[1]: *** [board.o] Error 1
make: *** [arch/arm/lib/libarm.o] Error 2
size: './u-boot': No such file
Configuring for omap3_zoom1 board...
board.c: In function '__dram_init_banksize':
board.c:233: error: 'CONFIG_SYS_SDRAM_BASE' undeclared (first use in
this function)
board.c:233: error: (Each undeclared identifier is reported only once
board.c:233: error: for each function it appears in.)
board.c: In function 'board_init_f':
board.c:279: error: 'CONFIG_SYS_INIT_SP_ADDR' undeclared (first use in
this function)
board.c:312: error: 'CONFIG_SYS_SDRAM_BASE' undeclared (first use in
this function)
make[1]: *** [board.o] Error 1
make: *** [arch/arm/lib/libarm.o] Error 2
size: './u-boot': No such file
Configuring for omap3_zoom2 board...
board.c: In function '__dram_init_banksize':
board.c:233: error: 'CONFIG_SYS_SDRAM_BASE' undeclared (first use in
this function)
board.c:233: error: (Each undeclared identifier is reported only once
board.c:233: error: for each function it appears in.)
board.c: In function 'board_init_f':
board.c:279: error: 'CONFIG_SYS_INIT_SP_ADDR' undeclared (first use in
this function)
board.c:312: error: 'CONFIG_SYS_SDRAM_BASE' undeclared (first use in
this function)
make[1]: *** [board.o] Error 1
make: *** [arch/arm/lib/libarm.o] Error 2
size: './u-boot': No such file
Configuring for omap4_panda board...
text data bss dec hex filename
147402 5892 201256 354550 568f6 ./u-boot
Configuring for omap4_sdp4430 board...
net/libnet.o: In function `rpc_req':
u-boot.git/net/nfs.c:193: undefined reference to `NetEthHdrSize'
u-boot.git/net/nfs.c:202: undefined reference to `NetSendUDPPacket'
u-boot.git/net/nfs.c:203: undefined reference to `NetTxPacket'
u-boot.git/net/nfs.c:203: undefined reference to `NetServerEther'
net/libnet.o: In function `NfsStart':
u-boot.git/net/nfs.c:741: undefined reference to `NetSetTimeout'
u-boot.git/net/nfs.c:742: undefined reference to `NetSetHandler'
u-boot.git/net/nfs.c:754: undefined reference to `BootFile'
u-boot.git/net/nfs.c:754: undefined reference to `NetServerIP'
u-boot.git/net/nfs.c:754: undefined reference to `NetOurIP'
u-boot.git/net/nfs.c:754: undefined reference to `NetOurGatewayIP'
u-boot.git/net/nfs.c:754: undefined reference to `NetOurSubnetMask'
u-boot.git/net/nfs.c:754: undefined reference to `NetBootFileSize'
u-boot.git/net/nfs.c:754: undefined reference to `NetServerEther'
net/libnet.o: In function `nfs_read_reply':
u-boot.git/net/nfs.c:563: undefined reference to `NetBootFileXferSize'
net/libnet.o: In function `NfsHandler':
u-boot.git/net/nfs.c:656: undefined reference to `NetSetTimeout'
u-boot.git/net/nfs.c:668: undefined reference to `NetState'
net/libnet.o: In function `NfsTimeout':
u-boot.git/net/nfs.c:574: undefined reference to `NetStartAgain'
u-boot.git/net/nfs.c:577: undefined reference to `NetSetTimeout'
arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
2.19.51.20090205 assertion fail
/scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12273
arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
2.19.51.20090205 assertion fail
/scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12273
arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
2.19.51.20090205 assertion fail
/scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12273
arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
2.19.51.20090205 assertion fail
/scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12273
arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
2.19.51.20090205 assertion fail
/scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12273
arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
2.19.51.20090205 assertion fail
/scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12507
/bin/sh: line 1: 4529 Segmentation fault arm-none-linux-gnueabi-ld
-Bstatic -T u-boot.lds -pie -Ttext 0x80e80000 $UNDEF_SYM
arch/arm/cpu/armv7/start.o --start-group lib/libgeneric.o
lib/lzma/liblzma.o lib/lzo/liblzo.o arch/arm/cpu/armv7/libarmv7.o
arch/arm/cpu/armv7/omap4/libomap4.o arch/arm/lib/libarm.o
fs/cramfs/libcramfs.o fs/fat/libfat.o fs/fdos/libfdos.o
fs/jffs2/libjffs2.o fs/reiserfs/libreiserfs.o fs/ext2/libext2fs.o
fs/yaffs2/libyaffs2.o fs/ubifs/libubifs.o net/libnet.o disk/libdisk.o
drivers/bios_emulator/libatibiosemu.o drivers/block/libblock.o
drivers/dma/libdma.o drivers/fpga/libfpga.o drivers/gpio/libgpio.o
drivers/hwmon/libhwmon.o drivers/i2c/libi2c.o drivers/input/libinput.o
drivers/misc/libmisc.o drivers/mmc/libmmc.o drivers/mtd/libmtd.o
drivers/mtd/nand/libnand.o drivers/mtd/onenand/libonenand.o
drivers/mtd/ubi/libubi.o drivers/mtd/spi/libspi_flash.o
drivers/net/libnet.o drivers/net/phy/libphy.o drivers/pci/libpci.o
drivers/pcmcia/libpcmcia.o drivers/power/libpower.o
drivers/spi/libspi.o drivers/rtc/librtc.o drivers/serial/libserial.o
drivers/twserial/libtws.o drivers/usb/gadget/libusb_gadget.o
drivers/usb/host/libusb_host.o drivers/usb/musb/libusb_musb.o
drivers/usb/phy/libusb_phy.o drivers/video/libvideo.o
drivers/watchdog/libwatchdog.o common/libcommon.o lib/libfdt/libfdt.o
api/libapi.o post/libpost.o
arch/arm/cpu/armv7/omap-common/libomap-common.o
board/ti/sdp4430/libsdp4430.o --end-group
u-boot.git/arch/arm/lib/eabi_compat.o -L
/opt/codesourcery/arm-none-linux-gnueabi/arm-2009q1/bin/../lib/gcc/arm-none-linux-gnueabi/4.3.3
-lgcc -Map u-boot.map -o u-boot
make: *** [u-boot] Error 139
size: ./u-boot: File format not recognized
Configuring for s5p_goni board...
board.c: In function 'board_init_f':
board.c:279: error: 'CONFIG_SYS_INIT_SP_ADDR' undeclared (first use in
this function)
board.c:279: error: (Each undeclared identifier is reported only once
board.c:279: error: for each function it appears in.)
make[1]: *** [board.o] Error 1
make: *** [arch/arm/lib/libarm.o] Error 2
size: './u-boot': No such file
Configuring for smdkc100 board...
board.c: In function 'board_init_f':
board.c:279: error: 'CONFIG_SYS_INIT_SP_ADDR' undeclared (first use in
this function)
board.c:279: error: (Each undeclared identifier is reported only once
board.c:279: error: for each function it appears in.)
make[1]: *** [board.o] Error 1
make: *** [arch/arm/lib/libarm.o] Error 2
size: './u-boot': No such file
--------------------- SUMMARY ----------------------------
Boards compiled: 17
Boards with warnings or errors: 11 ( am3517_evm ca9x4_ct_vxp
devkit8000 igep0030 omap3_evm omap3_sdp3430 omap3_zoom1 omap3_zoom2
omap4_sdp4430 s5p_goni smdkc100 )
----------------------------------------------------------
^ permalink raw reply [flat|nested] 40+ messages in thread* [U-Boot] Pull request: u-boot-arm
2010-11-27 7:43 ` Dirk Behme
@ 2010-11-27 9:06 ` Albert ARIBAUD
2010-11-27 17:19 ` Paulraj, Sandeep
2010-11-27 18:50 ` Wolfgang Denk
2010-11-27 23:33 ` Steve Sakoman
2010-11-29 20:16 ` Dirk Behme
2 siblings, 2 replies; 40+ messages in thread
From: Albert ARIBAUD @ 2010-11-27 9:06 UTC (permalink / raw)
To: u-boot
Le 27/11/2010 08:43, Dirk Behme a ?crit :
> Doing a './MAKEALL ARMV7' on the recent master (d4752d5d2...) doesn't
> look nice [2].
Globally, this is expected and does not hit only ARMV7 but any ARM board
-- I think on the whole MAKEALL arm, only 35 out of 168 boards build
without errors or warnings (more do build, but with warnings though).
ELF relocation was introduced during this cycle, on all ARM cpus but
only on a handful of boards. Others need to be fixed by their
maintainers. Typically, those which miss a CONFIG_SYS_SDRAM_BASE are hit
by this issue. Note that not fixing all boards is voluntary: those
boards whose maintainer will not have fixed during the coming cycle will
be removed--as a janitorial matter, one could say.
For others -- the break may or may not be a consequence of ELF
relocation. This will have to be fixed on an individual basis.
> Are there any other pending patches to fix the compilation of the
> failing boards?
These shall be fixed by their maintainers.
Wolfgang, should I send out a (single) mail to each ARM board maintainer
right after this cycle asking them to either fix their board or say that
they are not going to? This could help weed out during next cycle.
> Thanks
>
> Dirk
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
2010-11-27 9:06 ` Albert ARIBAUD
@ 2010-11-27 17:19 ` Paulraj, Sandeep
2010-11-27 19:36 ` Wolfgang Denk
2010-11-27 18:50 ` Wolfgang Denk
1 sibling, 1 reply; 40+ messages in thread
From: Paulraj, Sandeep @ 2010-11-27 17:19 UTC (permalink / raw)
To: u-boot
>Wolfgang, should I send out a (single) mail to each ARM board maintainer
>right after this cycle asking them to either fix their board or say that
>they are not going to? This could help weed out during next cycle.
IIRC if by the next release cycle, the errors are not fixed,
the boards will/should be removed by the individual tree maintainers.
I believe this has already been communicated on the list.
--Sandeep
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
2010-11-27 17:19 ` Paulraj, Sandeep
@ 2010-11-27 19:36 ` Wolfgang Denk
0 siblings, 0 replies; 40+ messages in thread
From: Wolfgang Denk @ 2010-11-27 19:36 UTC (permalink / raw)
To: u-boot
Dear "Paulraj, Sandeep",
In message <0554BEF07D437848AF01B9C9B5F0BC5DBCFDDECA@dlee01.ent.ti.com> you wrote:
>
> IIRC if by the next release cycle, the errors are not fixed,
> the boards will/should be removed by the individual tree maintainers.
>
> I believe this has already been communicated on the list.
True. On the other hand, some board maintainers may think they are not
affected, or expect a special invitation. It cannot hurt to
explicitly tell them again that they must become active now.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"Whoever undertakes to set himself up as a judge of Truth and Know-
ledge is shipwrecked by the laughter of the gods." - Albert Einstein
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
2010-11-27 9:06 ` Albert ARIBAUD
2010-11-27 17:19 ` Paulraj, Sandeep
@ 2010-11-27 18:50 ` Wolfgang Denk
2010-11-27 19:42 ` Albert ARIBAUD
2010-11-28 5:15 ` Thomas Weber
1 sibling, 2 replies; 40+ messages in thread
From: Wolfgang Denk @ 2010-11-27 18:50 UTC (permalink / raw)
To: u-boot
Dear Albert ARIBAUD,
In message <4CF0CA18.1000206@free.fr> you wrote:
>
> Globally, this is expected and does not hit only ARMV7 but any ARM board
> -- I think on the whole MAKEALL arm, only 35 out of 168 boards build
> without errors or warnings (more do build, but with warnings though).
Correct. My last build shows 130 out of 168 with errors or warnings.
> These shall be fixed by their maintainers.
>
> Wolfgang, should I send out a (single) mail to each ARM board maintainer
> right after this cycle asking them to either fix their board or say that
> they are not going to? This could help weed out during next cycle.
We might as well do this right now. I will try to get -rc2 out this
weekend, and also start a "next" branch. Maybe some board maintainers
need a special invitation to fix their boards - eventually some will
submit patches even for this release. It's worth a try.
Thanks.
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
What was sliced bread the greatest thing since?
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
2010-11-27 18:50 ` Wolfgang Denk
@ 2010-11-27 19:42 ` Albert ARIBAUD
2010-11-27 20:50 ` Wolfgang Denk
2010-11-28 5:15 ` Thomas Weber
1 sibling, 1 reply; 40+ messages in thread
From: Albert ARIBAUD @ 2010-11-27 19:42 UTC (permalink / raw)
To: u-boot
Le 27/11/2010 19:50, Wolfgang Denk a ?crit :
>> Wolfgang, should I send out a (single) mail to each ARM board maintainer
>> right after this cycle asking them to either fix their board or say that
>> they are not going to? This could help weed out during next cycle.
>
> We might as well do this right now. I will try to get -rc2 out this
> weekend, and also start a "next" branch. Maybe some board maintainers
> need a special invitation to fix their boards - eventually some will
> submit patches even for this release. It's worth a try.
>
> Thanks.
>
> Wolfgang Denk
No problem. I am building a list of addresses from the MAINTAINERS list.
For those boards which have no maintainer I will use the e-mail address
of the last committer to the config header file (skipping Wolfgang's, of
course).
I will then send a single mail to myself with everybody in Bcc:, telling
them that they are e-mailed as the maintainer or last committer to an
u-boot board, informing them of the recent introduction of ELF
relocation to u-boot, that it breaks building the board, and that they
should take steps to fix the board (these steps may be as simple as
adding a couple of lines similar to what was done with edminiv2.h)
otherwise the board will be considered orphan and risk being removed.
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
2010-11-27 19:42 ` Albert ARIBAUD
@ 2010-11-27 20:50 ` Wolfgang Denk
2010-11-27 21:15 ` Albert ARIBAUD
0 siblings, 1 reply; 40+ messages in thread
From: Wolfgang Denk @ 2010-11-27 20:50 UTC (permalink / raw)
To: u-boot
Dear Albert ARIBAUD,
In message <4CF15F20.9060300@free.fr> you wrote:
>
> No problem. I am building a list of addresses from the MAINTAINERS list.
Thanks.
> For those boards which have no maintainer I will use the e-mail address
> of the last committer to the config header file (skipping Wolfgang's, of
> course).
Be carefule. There were a lot or global actions done by many people.
Rather look at less frequently change files, like board/*/Makefile,
and use the _first_ committer.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"The question of whether a computer can think is no more interesting
than the question of whether a submarine can swim"
- Edsgar W. Dijkstra
^ permalink raw reply [flat|nested] 40+ messages in thread* [U-Boot] Pull request: u-boot-arm
2010-11-27 20:50 ` Wolfgang Denk
@ 2010-11-27 21:15 ` Albert ARIBAUD
2010-11-27 22:09 ` Albert ARIBAUD
0 siblings, 1 reply; 40+ messages in thread
From: Albert ARIBAUD @ 2010-11-27 21:15 UTC (permalink / raw)
To: u-boot
Le 27/11/2010 21:50, Wolfgang Denk a ?crit :
>> For those boards which have no maintainer I will use the e-mail address
>> of the last committer to the config header file (skipping Wolfgang's, of
>> course).
>
> Be carefule. There were a lot or global actions done by many people.
> Rather look at less frequently change files, like board/*/Makefile,
> and use the _first_ committer.
Thanks for pointing this out. For the moment I'll stick with mailing
only official board maintainers. Then I'll carefully go through boards
without official maintainers one by one.
> Best regards,
>
> Wolfgang Denk
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
2010-11-27 21:15 ` Albert ARIBAUD
@ 2010-11-27 22:09 ` Albert ARIBAUD
2010-11-27 22:27 ` Albert ARIBAUD
2010-11-28 7:40 ` Dirk Behme
0 siblings, 2 replies; 40+ messages in thread
From: Albert ARIBAUD @ 2010-11-27 22:09 UTC (permalink / raw)
To: u-boot
Le 27/11/2010 22:15, Albert ARIBAUD a ?crit :
> Thanks for pointing this out. For the moment I'll stick with mailing
> only official board maintainers. Then I'll carefully go through boards
> without official maintainers one by one.
Message sent out, mistakenly from my alternate address albert at
aribaud.net, but anyway... I have had five NDRs, for the following
addresses which are all unknown; corresponding boards (within
parentheses) should probably be moved to 'unmaintained':
mani.pillai at ti.com (omap3_evm)
kletschke at synertronixx.de (scb9328)
mag at sysgo.com (impa7 and ep7312)
prakash at embedx.com (cerf250)
kshitij at ti.com (omap1510inn, omap1610inn)
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
2010-11-27 22:09 ` Albert ARIBAUD
@ 2010-11-27 22:27 ` Albert ARIBAUD
2010-11-28 7:40 ` Dirk Behme
1 sibling, 0 replies; 40+ messages in thread
From: Albert ARIBAUD @ 2010-11-27 22:27 UTC (permalink / raw)
To: u-boot
Le 27/11/2010 23:09, Albert ARIBAUD a ?crit :
> Le 27/11/2010 22:15, Albert ARIBAUD a ?crit :
>
>> Thanks for pointing this out. For the moment I'll stick with mailing
>> only official board maintainers. Then I'll carefully go through boards
>> without official maintainers one by one.
>
> Message sent out, mistakenly from my alternate address albert at
> aribaud.net, but anyway... I have had five NDRs, for the following
> addresses which are all unknown; corresponding boards (within
> parentheses) should probably be moved to 'unmaintained':
>
> mani.pillai at ti.com (omap3_evm)
> kletschke at synertronixx.de (scb9328)
> mag at sysgo.com (impa7 and ep7312)
> prakash at embedx.com (cerf250)
> kshitij at ti.com (omap1510inn, omap1610inn)
>
> Amicalement,
Apparently MAINTAINERS entry for Stelian Pop is not correct any more;
CC:ing Stelian's address as last seen on the list. If this one is
correct, then MAINTAINERS should be fixed.
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
2010-11-27 22:09 ` Albert ARIBAUD
2010-11-27 22:27 ` Albert ARIBAUD
@ 2010-11-28 7:40 ` Dirk Behme
1 sibling, 0 replies; 40+ messages in thread
From: Dirk Behme @ 2010-11-28 7:40 UTC (permalink / raw)
To: u-boot
On 27.11.2010 23:09, Albert ARIBAUD wrote:
> Le 27/11/2010 22:15, Albert ARIBAUD a ?crit :
>
>> Thanks for pointing this out. For the moment I'll stick with mailing
>> only official board maintainers. Then I'll carefully go through boards
>> without official maintainers one by one.
>
> Message sent out, mistakenly from my alternate address albert at
> aribaud.net, but anyway... I have had five NDRs, for the following
> addresses which are all unknown; corresponding boards (within
> parentheses) should probably be moved to 'unmaintained':
>
> mani.pillai at ti.com (omap3_evm)
...
> kshitij at ti.com (omap1510inn, omap1610inn)
Maybe Sandeep could help with this?
Thanks
Dirk
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
2010-11-27 18:50 ` Wolfgang Denk
2010-11-27 19:42 ` Albert ARIBAUD
@ 2010-11-28 5:15 ` Thomas Weber
1 sibling, 0 replies; 40+ messages in thread
From: Thomas Weber @ 2010-11-28 5:15 UTC (permalink / raw)
To: u-boot
On Sat, Nov 27, 2010 at 7:50 PM, Wolfgang Denk <wd@denx.de> wrote:
> Dear Albert ARIBAUD,
>
> In message <4CF0CA18.1000206@free.fr> you wrote:
>>
>> Globally, this is expected and does not hit only ARMV7 but any ARM board
>> -- I think on the whole MAKEALL arm, only 35 out of 168 boards build
>> without errors or warnings (more do build, but with warnings though).
>
> Correct. My last build shows 130 out of 168 with errors or warnings.
>
>> These shall be fixed by their maintainers.
>>
>> Wolfgang, should I send out a (single) mail to each ARM board maintainer
>> right after this cycle asking them to either fix their board or say that
>> they are not going to? This could help weed out during next cycle.
>
> We might as well do this right now. ? I will try to get -rc2 out this
> weekend, and also start a "next" branch. ?Maybe some board maintainers
> need a special invitation to fix their boards - eventually some will
> submit patches even for this release. It's worth a try.
>
> Thanks.
>
> Wolfgang Denk
>
> --
> DENX Software Engineering GmbH, ? ? MD: Wolfgang Denk & Detlev Zundel
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
> What was sliced bread the greatest thing since?
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
>
Hello,
http://patchwork.ozlabs.org/patch/72060/
fixes the GERNERATED_GBL_DATA_SIZE for Devkit8000.
Thomas
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
2010-11-27 7:43 ` Dirk Behme
2010-11-27 9:06 ` Albert ARIBAUD
@ 2010-11-27 23:33 ` Steve Sakoman
2010-11-27 23:57 ` Paulraj, Sandeep
2010-11-29 20:16 ` Dirk Behme
2 siblings, 1 reply; 40+ messages in thread
From: Steve Sakoman @ 2010-11-27 23:33 UTC (permalink / raw)
To: u-boot
On Fri, Nov 26, 2010 at 11:43 PM, Dirk Behme <dirk.behme@googlemail.com> wrote:
> On 26.11.2010 21:55, Wolfgang Denk wrote:
>> In message<20101126202955.B087D11D94F7@gemini.denx.de> ?you wrote:
>>> The following changes since commit 6163f5b4c8873848ed023054bc401727301ea537:
>>>
>>> ? ?malloc: Fix issue with calloc memory possibly being non-zero (2010-11-17 22:06:40 +0100)
>>>
>>> are available in the git repository at:
>>> ? ?git://git.denx.de/u-boot-arm.git master
> ...
>>
>> Applied.
>
> Doing a './MAKEALL ARMV7' on the recent master (d4752d5d2...) doesn't
> look nice [2].
>
> The following configs build fine:
>
> igep0020
> mx51evk
> omap3_beagle
> omap3_overo
> omap3_pandora
> omap4_panda
I have hardware for igep0020, beagle, overo, panda, and sdp4430. I
build daily for these machines and submit patches when they break
(there is a patch pending for omap4430 that fixes the build for it).
Steve
> The following boards fail to build:
>
> am3517_evm board
> ca9x4_ct_vxp
> devkit8000
> igep0030
> omap3_evm
> omap3_sdp3430
> omap3_zoom1
> omap3_zoom2
> omap4_sdp4430
> s5p_goni
> smdkc100
>
> I applied [1] to fix a beagle warning.
>
> Are there any other pending patches to fix the compilation of the
> failing boards?
>
> Thanks
>
> Dirk
>
> [1] http://patchwork.ozlabs.org/patch/72453/
>
> [2] > ./MAKEALL ARMV7
> Configuring for am3517_evm board...
> board.c: In function '__dram_init_banksize':
> board.c:233: error: 'CONFIG_SYS_SDRAM_BASE' undeclared (first use in
> this function)
> board.c:233: error: (Each undeclared identifier is reported only once
> board.c:233: error: for each function it appears in.)
> board.c: In function 'board_init_f':
> board.c:279: error: 'CONFIG_SYS_INIT_SP_ADDR' undeclared (first use in
> this function)
> board.c:312: error: 'CONFIG_SYS_SDRAM_BASE' undeclared (first use in
> this function)
> make[1]: *** [board.o] Error 1
> make: *** [arch/arm/lib/libarm.o] Error 2
> size: './u-boot': No such file
> Configuring for ca9x4_ct_vxp board...
> syslib.c:26:32: error: asm/arch/sys_proto.h: No such file or directory
> make[1]: *** No rule to build the target ?.depend?,
> ? needed from ?_depend?. ?End.
> syslib.c:26:32: error: asm/arch/sys_proto.h: No such file or directory
> make[1]: *** [syslib.o] Error 1
> make: *** [arch/arm/cpu/armv7/libarmv7.o] Error 2
> size: './u-boot': No such file
> Configuring for devkit8000 board...
> start.S: Assembler messages:
> start.S:144: Error: constant expression expected -- `ldr
> sp,=((0x4020FFFC-CONFIG_SYS_GBL_DATA_SIZE))'
> make[1]: *** [start.o] Error 1
> make: *** [arch/arm/cpu/armv7/start.o] Error 2
> size: './u-boot': No such file
> Configuring for igep0020 board...
> ? ?text ? ?data ? ? bss ? ? dec ? ? hex filename
> ?219538 ? ?7768 ?214536 ?441842 ? 6bdf2 ./u-boot
> Configuring for igep0030 board...
> net/libnet.o: In function `rpc_req':
> u-boot.git/net/nfs.c:193: undefined reference to `NetEthHdrSize'
> u-boot.git/net/nfs.c:202: undefined reference to `NetSendUDPPacket'
> u-boot.git/net/nfs.c:203: undefined reference to `NetTxPacket'
> u-boot.git/net/nfs.c:203: undefined reference to `NetServerEther'
> net/libnet.o: In function `NfsStart':
> u-boot.git/net/nfs.c:741: undefined reference to `NetSetTimeout'
> u-boot.git/net/nfs.c:742: undefined reference to `NetSetHandler'
> u-boot.git/net/nfs.c:754: undefined reference to `BootFile'
> u-boot.git/net/nfs.c:754: undefined reference to `NetServerIP'
> u-boot.git/net/nfs.c:754: undefined reference to `NetOurIP'
> u-boot.git/net/nfs.c:754: undefined reference to `NetOurGatewayIP'
> u-boot.git/net/nfs.c:754: undefined reference to `NetOurSubnetMask'
> u-boot.git/net/nfs.c:754: undefined reference to `NetBootFileSize'
> u-boot.git/net/nfs.c:754: undefined reference to `NetServerEther'
> net/libnet.o: In function `nfs_read_reply':
> u-boot.git/net/nfs.c:563: undefined reference to `NetBootFileXferSize'
> net/libnet.o: In function `NfsHandler':
> u-boot.git/net/nfs.c:656: undefined reference to `NetSetTimeout'
> u-boot.git/net/nfs.c:668: undefined reference to `NetState'
> net/libnet.o: In function `NfsTimeout':
> u-boot.git/net/nfs.c:574: undefined reference to `NetStartAgain'
> u-boot.git/net/nfs.c:577: undefined reference to `NetSetTimeout'
> arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
> 2.19.51.20090205 assertion fail
> /scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12273
> arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
> 2.19.51.20090205 assertion fail
> /scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12273
> arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
> 2.19.51.20090205 assertion fail
> /scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12273
> arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
> 2.19.51.20090205 assertion fail
> /scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12273
> arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
> 2.19.51.20090205 assertion fail
> /scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12273
> arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
> 2.19.51.20090205 assertion fail
> /scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12507
> /bin/sh: line 1: ?8055 Segmentation fault ?arm-none-linux-gnueabi-ld
> -Bstatic -T u-boot.lds -pie -Ttext 0x80008000 $UNDEF_SYM
> arch/arm/cpu/armv7/start.o --start-group lib/libgeneric.o
> lib/lzma/liblzma.o lib/lzo/liblzo.o arch/arm/cpu/armv7/libarmv7.o
> arch/arm/cpu/armv7/omap3/libomap3.o arch/arm/lib/libarm.o
> fs/cramfs/libcramfs.o fs/fat/libfat.o fs/fdos/libfdos.o
> fs/jffs2/libjffs2.o fs/reiserfs/libreiserfs.o fs/ext2/libext2fs.o
> fs/yaffs2/libyaffs2.o fs/ubifs/libubifs.o net/libnet.o disk/libdisk.o
> drivers/bios_emulator/libatibiosemu.o drivers/block/libblock.o
> drivers/dma/libdma.o drivers/fpga/libfpga.o drivers/gpio/libgpio.o
> drivers/hwmon/libhwmon.o drivers/i2c/libi2c.o drivers/input/libinput.o
> drivers/misc/libmisc.o drivers/mmc/libmmc.o drivers/mtd/libmtd.o
> drivers/mtd/nand/libnand.o drivers/mtd/onenand/libonenand.o
> drivers/mtd/ubi/libubi.o drivers/mtd/spi/libspi_flash.o
> drivers/net/libnet.o drivers/net/phy/libphy.o drivers/pci/libpci.o
> drivers/pcmcia/libpcmcia.o drivers/power/libpower.o
> drivers/spi/libspi.o drivers/rtc/librtc.o drivers/serial/libserial.o
> drivers/twserial/libtws.o drivers/usb/gadget/libusb_gadget.o
> drivers/usb/host/libusb_host.o drivers/usb/musb/libusb_musb.o
> drivers/usb/phy/libusb_phy.o drivers/video/libvideo.o
> drivers/watchdog/libwatchdog.o common/libcommon.o lib/libfdt/libfdt.o
> api/libapi.o post/libpost.o
> arch/arm/cpu/armv7/omap-common/libomap-common.o
> board/isee/igep0030/libigep0030.o --end-group
> u-boot.git/arch/arm/lib/eabi_compat.o -L
> /opt/codesourcery/arm-none-linux-gnueabi/arm-2009q1/bin/../lib/gcc/arm-none-linux-gnueabi/4.3.3
> -lgcc -Map u-boot.map -o u-boot
> make: *** [u-boot] Error 139
> size: ./u-boot: File format not recognized
> Configuring for mx51evk board...
> ? ?text ? ?data ? ? bss ? ? dec ? ? hex filename
> ?159945 ? ?6504 ?216928 ?383377 ? 5d991 ./u-boot
> Configuring for omap3_beagle board...
> ? ?text ? ?data ? ? bss ? ? dec ? ? hex filename
> ?249978 ? 11288 ?203700 ?464966 ? 71846 ./u-boot
> Configuring for omap3_overo board...
> ? ?text ? ?data ? ? bss ? ? dec ? ? hex filename
> ?216254 ? 10836 ?210628 ?437718 ? 6add6 ./u-boot
> Configuring for omap3_evm board...
> start.S: Assembler messages:
> start.S:144: Error: constant expression expected -- `ldr
> sp,=((0x4020FFFC-CONFIG_SYS_GBL_DATA_SIZE))'
> make[1]: *** [start.o] Error 1
> make: *** [arch/arm/cpu/armv7/start.o] Error 2
> size: './u-boot': No such file
> Configuring for omap3_pandora board...
> ? ?text ? ?data ? ? bss ? ? dec ? ? hex filename
> ?326528 ? 10480 ?205116 ?542124 ? 845ac ./u-boot
> Configuring for omap3_sdp3430 board...
> board.c: In function '__dram_init_banksize':
> board.c:233: error: 'CONFIG_SYS_SDRAM_BASE' undeclared (first use in
> this function)
> board.c:233: error: (Each undeclared identifier is reported only once
> board.c:233: error: for each function it appears in.)
> board.c: In function 'board_init_f':
> board.c:279: error: 'CONFIG_SYS_INIT_SP_ADDR' undeclared (first use in
> this function)
> board.c:312: error: 'CONFIG_SYS_SDRAM_BASE' undeclared (first use in
> this function)
> make[1]: *** [board.o] Error 1
> make: *** [arch/arm/lib/libarm.o] Error 2
> size: './u-boot': No such file
> Configuring for omap3_zoom1 board...
> board.c: In function '__dram_init_banksize':
> board.c:233: error: 'CONFIG_SYS_SDRAM_BASE' undeclared (first use in
> this function)
> board.c:233: error: (Each undeclared identifier is reported only once
> board.c:233: error: for each function it appears in.)
> board.c: In function 'board_init_f':
> board.c:279: error: 'CONFIG_SYS_INIT_SP_ADDR' undeclared (first use in
> this function)
> board.c:312: error: 'CONFIG_SYS_SDRAM_BASE' undeclared (first use in
> this function)
> make[1]: *** [board.o] Error 1
> make: *** [arch/arm/lib/libarm.o] Error 2
> size: './u-boot': No such file
> Configuring for omap3_zoom2 board...
> board.c: In function '__dram_init_banksize':
> board.c:233: error: 'CONFIG_SYS_SDRAM_BASE' undeclared (first use in
> this function)
> board.c:233: error: (Each undeclared identifier is reported only once
> board.c:233: error: for each function it appears in.)
> board.c: In function 'board_init_f':
> board.c:279: error: 'CONFIG_SYS_INIT_SP_ADDR' undeclared (first use in
> this function)
> board.c:312: error: 'CONFIG_SYS_SDRAM_BASE' undeclared (first use in
> this function)
> make[1]: *** [board.o] Error 1
> make: *** [arch/arm/lib/libarm.o] Error 2
> size: './u-boot': No such file
> Configuring for omap4_panda board...
> ? ?text ? ?data ? ? bss ? ? dec ? ? hex filename
> ?147402 ? ?5892 ?201256 ?354550 ? 568f6 ./u-boot
> Configuring for omap4_sdp4430 board...
> net/libnet.o: In function `rpc_req':
> u-boot.git/net/nfs.c:193: undefined reference to `NetEthHdrSize'
> u-boot.git/net/nfs.c:202: undefined reference to `NetSendUDPPacket'
> u-boot.git/net/nfs.c:203: undefined reference to `NetTxPacket'
> u-boot.git/net/nfs.c:203: undefined reference to `NetServerEther'
> net/libnet.o: In function `NfsStart':
> u-boot.git/net/nfs.c:741: undefined reference to `NetSetTimeout'
> u-boot.git/net/nfs.c:742: undefined reference to `NetSetHandler'
> u-boot.git/net/nfs.c:754: undefined reference to `BootFile'
> u-boot.git/net/nfs.c:754: undefined reference to `NetServerIP'
> u-boot.git/net/nfs.c:754: undefined reference to `NetOurIP'
> u-boot.git/net/nfs.c:754: undefined reference to `NetOurGatewayIP'
> u-boot.git/net/nfs.c:754: undefined reference to `NetOurSubnetMask'
> u-boot.git/net/nfs.c:754: undefined reference to `NetBootFileSize'
> u-boot.git/net/nfs.c:754: undefined reference to `NetServerEther'
> net/libnet.o: In function `nfs_read_reply':
> u-boot.git/net/nfs.c:563: undefined reference to `NetBootFileXferSize'
> net/libnet.o: In function `NfsHandler':
> u-boot.git/net/nfs.c:656: undefined reference to `NetSetTimeout'
> u-boot.git/net/nfs.c:668: undefined reference to `NetState'
> net/libnet.o: In function `NfsTimeout':
> u-boot.git/net/nfs.c:574: undefined reference to `NetStartAgain'
> u-boot.git/net/nfs.c:577: undefined reference to `NetSetTimeout'
> arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
> 2.19.51.20090205 assertion fail
> /scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12273
> arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
> 2.19.51.20090205 assertion fail
> /scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12273
> arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
> 2.19.51.20090205 assertion fail
> /scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12273
> arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
> 2.19.51.20090205 assertion fail
> /scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12273
> arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
> 2.19.51.20090205 assertion fail
> /scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12273
> arm-none-linux-gnueabi-ld: BFD (Sourcery G++ Lite 2009q1-203)
> 2.19.51.20090205 assertion fail
> /scratch/mitchell/builds/4.3-arm-none-linux-gnueabi-respin/lite/obj/binutils-src-2009q1-203-arm-none-linux-gnueabi-i686-pc-linux-gnu/bfd/elf32-arm.c:12507
> /bin/sh: line 1: ?4529 Segmentation fault ?arm-none-linux-gnueabi-ld
> -Bstatic -T u-boot.lds -pie -Ttext 0x80e80000 $UNDEF_SYM
> arch/arm/cpu/armv7/start.o --start-group lib/libgeneric.o
> lib/lzma/liblzma.o lib/lzo/liblzo.o arch/arm/cpu/armv7/libarmv7.o
> arch/arm/cpu/armv7/omap4/libomap4.o arch/arm/lib/libarm.o
> fs/cramfs/libcramfs.o fs/fat/libfat.o fs/fdos/libfdos.o
> fs/jffs2/libjffs2.o fs/reiserfs/libreiserfs.o fs/ext2/libext2fs.o
> fs/yaffs2/libyaffs2.o fs/ubifs/libubifs.o net/libnet.o disk/libdisk.o
> drivers/bios_emulator/libatibiosemu.o drivers/block/libblock.o
> drivers/dma/libdma.o drivers/fpga/libfpga.o drivers/gpio/libgpio.o
> drivers/hwmon/libhwmon.o drivers/i2c/libi2c.o drivers/input/libinput.o
> drivers/misc/libmisc.o drivers/mmc/libmmc.o drivers/mtd/libmtd.o
> drivers/mtd/nand/libnand.o drivers/mtd/onenand/libonenand.o
> drivers/mtd/ubi/libubi.o drivers/mtd/spi/libspi_flash.o
> drivers/net/libnet.o drivers/net/phy/libphy.o drivers/pci/libpci.o
> drivers/pcmcia/libpcmcia.o drivers/power/libpower.o
> drivers/spi/libspi.o drivers/rtc/librtc.o drivers/serial/libserial.o
> drivers/twserial/libtws.o drivers/usb/gadget/libusb_gadget.o
> drivers/usb/host/libusb_host.o drivers/usb/musb/libusb_musb.o
> drivers/usb/phy/libusb_phy.o drivers/video/libvideo.o
> drivers/watchdog/libwatchdog.o common/libcommon.o lib/libfdt/libfdt.o
> api/libapi.o post/libpost.o
> arch/arm/cpu/armv7/omap-common/libomap-common.o
> board/ti/sdp4430/libsdp4430.o --end-group
> u-boot.git/arch/arm/lib/eabi_compat.o -L
> /opt/codesourcery/arm-none-linux-gnueabi/arm-2009q1/bin/../lib/gcc/arm-none-linux-gnueabi/4.3.3
> -lgcc -Map u-boot.map -o u-boot
> make: *** [u-boot] Error 139
> size: ./u-boot: File format not recognized
> Configuring for s5p_goni board...
> board.c: In function 'board_init_f':
> board.c:279: error: 'CONFIG_SYS_INIT_SP_ADDR' undeclared (first use in
> this function)
> board.c:279: error: (Each undeclared identifier is reported only once
> board.c:279: error: for each function it appears in.)
> make[1]: *** [board.o] Error 1
> make: *** [arch/arm/lib/libarm.o] Error 2
> size: './u-boot': No such file
> Configuring for smdkc100 board...
> board.c: In function 'board_init_f':
> board.c:279: error: 'CONFIG_SYS_INIT_SP_ADDR' undeclared (first use in
> this function)
> board.c:279: error: (Each undeclared identifier is reported only once
> board.c:279: error: for each function it appears in.)
> make[1]: *** [board.o] Error 1
> make: *** [arch/arm/lib/libarm.o] Error 2
> size: './u-boot': No such file
>
> --------------------- SUMMARY ----------------------------
> Boards compiled: 17
> Boards with warnings or errors: 11 ( am3517_evm ca9x4_ct_vxp
> devkit8000 igep0030 omap3_evm omap3_sdp3430 omap3_zoom1 omap3_zoom2
> omap4_sdp4430 s5p_goni smdkc100 )
> ----------------------------------------------------------
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
>
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
2010-11-27 23:33 ` Steve Sakoman
@ 2010-11-27 23:57 ` Paulraj, Sandeep
2010-11-28 3:15 ` Steve Sakoman
0 siblings, 1 reply; 40+ messages in thread
From: Paulraj, Sandeep @ 2010-11-27 23:57 UTC (permalink / raw)
To: u-boot
>
> I have hardware for igep0020, beagle, overo, panda, and sdp4430. I
> build daily for these machines and submit patches when they break
> (there is a patch pending for omap4430 that fixes the build for it).
Which patch? Can you give me the link?
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
2010-11-27 23:57 ` Paulraj, Sandeep
@ 2010-11-28 3:15 ` Steve Sakoman
0 siblings, 0 replies; 40+ messages in thread
From: Steve Sakoman @ 2010-11-28 3:15 UTC (permalink / raw)
To: u-boot
On Sat, Nov 27, 2010 at 3:57 PM, Paulraj, Sandeep <s-paulraj@ti.com> wrote:
>
>> I have hardware for igep0020, beagle, overo, panda, and sdp4430. I
>> build daily for these machines and submit patches when they break
>> (there is a patch pending for omap4430 that fixes the build for it).
>
> Which patch? Can you give me the link?
Fear not, you didn't miss anything! The patch just made it to
mainline from the arm branch:
http://git.denx.de/?p=u-boot.git;a=commit;h=8721e95b16024f0a92ccc1cd85aecf6672fe9499
Steve
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
2010-11-27 7:43 ` Dirk Behme
2010-11-27 9:06 ` Albert ARIBAUD
2010-11-27 23:33 ` Steve Sakoman
@ 2010-11-29 20:16 ` Dirk Behme
2010-11-29 20:27 ` Paulraj, Sandeep
2 siblings, 1 reply; 40+ messages in thread
From: Dirk Behme @ 2010-11-29 20:16 UTC (permalink / raw)
To: u-boot
On 27.11.2010 08:43, Dirk Behme wrote:
> On 26.11.2010 21:55, Wolfgang Denk wrote:
>> In message<20101126202955.B087D11D94F7@gemini.denx.de> you wrote:
>>> The following changes since commit
>>> 6163f5b4c8873848ed023054bc401727301ea537:
>>>
>>> malloc: Fix issue with calloc memory possibly being non-zero
>>> (2010-11-17 22:06:40 +0100)
>>>
>>> are available in the git repository at:
>>> git://git.denx.de/u-boot-arm.git master
> ...
>>
>> Applied.
>
> Doing a './MAKEALL ARMV7' on the recent master (d4752d5d2...) doesn't
> look nice [2].
>
> The following configs build fine:
>
> igep0020
> mx51evk
> omap3_beagle
> omap3_overo
> omap3_pandora
> omap4_panda
>
> The following boards fail to build:
Just fyi, scanning the list archive, for most of the boards there are
patches available fixing the build:
> am3517_evm
http://lists.denx.de/pipermail/u-boot/2010-November/082641.html
http://lists.denx.de/pipermail/u-boot/2010-November/082642.html
> ca9x4_ct_vxp
http://lists.denx.de/pipermail/u-boot/2010-November/081033.html
http://lists.denx.de/pipermail/u-boot/2010-November/081034.html
http://lists.denx.de/pipermail/u-boot/2010-November/082654.html
> devkit8000
Already fixed in mainline now
> igep0030
http://lists.denx.de/pipermail/u-boot/2010-November/082603.html
> omap3_evm
http://lists.denx.de/pipermail/u-boot/2010-November/082606.html
But I still get an error
Configuring for omap3_evm board...
arm-none-linux-gnueabi-ld: section .bss [8003f5c0 -> 8007e31f]
overlaps section .rel.dyn [8003f5c0 -> 80044e4f]
arm-none-linux-gnueabi-ld: section .dynsym [80044e50 -> 80044eef]
overlaps section .bss [8003f5c0 -> 8007e31f]
arm-none-linux-gnueabi-ld: u-boot: section .bss vma 0x8003f5c0
overlaps previous sections
make: *** [u-boot] Error 1
size: './u-boot': No such file
I have to check if there is already a fix available.
> omap3_sdp3430
http://lists.denx.de/pipermail/u-boot/2010-November/082649.html
> omap3_zoom1
http://lists.denx.de/pipermail/u-boot/2010-November/082650.html
> omap3_zoom2
http://lists.denx.de/pipermail/u-boot/2010-November/082651.html
> omap4_sdp4430
http://lists.denx.de/pipermail/u-boot/2010-November/082556.html
> s5p_goni
http://lists.denx.de/pipermail/u-boot/2010-November/082225.html
> smdkc100
http://lists.denx.de/pipermail/u-boot/2010-November/082224.html
So it seems to me that the last ARMV7 board with build issues is
omap3_evm. But as mentioned, I have to check the archives for this.
Best regards
Dirk
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
@ 2010-11-17 19:50 Wolfgang Denk
2010-11-17 19:55 ` Wolfgang Denk
2010-11-17 21:34 ` Loïc Minier
0 siblings, 2 replies; 40+ messages in thread
From: Wolfgang Denk @ 2010-11-17 19:50 UTC (permalink / raw)
To: u-boot
The following changes since commit d963e84c92a63b4e6c4f2f80482a5ecbe9b24fe0:
Merge branch 'master' of /home/wd/git/u-boot/master (2010-11-12 22:24:06 +0100)
are available in the git repository at:
git://git.denx.de/u-boot-arm.git master
Alagu Sankar (1):
mmc: Add multi-block read support to the generic mmc driver
Albert Aribaud (2):
ARM: fix linker file for newer ld support
tx25: fix linker file for newer ld support
Enric Balletbo i Serra (2):
ARMV7: OMAP3: Use generic mmc driver on IGEP v2
ARMV7: OMAP3: Use generic mmc driver on OMAP3 IGEP module
Heiko Schocher (1):
armv7, beagle: Second SDRAM bank don;t work
Koen Kooi (1):
ARMV7: OMAP3: Add expansion board detection for Beagle
Reinhard Meyer (2):
AT91: add 2nd SPI to 9260/9XE/9G20
AT91: add header file for the Shutdown Controller
Sanjeev Premi (3):
omap3evm: Support relocation
omap3evm: Wrap function under CONFIG_USB_OMAP3
omap3evm: Fix mechanism to identify board revision
Steve Sakoman (5):
ARMV7: OMAP3: IGEP: Rename TEXT_BASE
ARMV7: Fix build for non-OMAP3 boards
ARMV7: OMAP3: Add expansion board detection for Overo
ARMV7: OMAP: Fix build after introduction of GENERATED_GBL_DATA_SIZE
mmc: Clean up generic mmc driver multi-block write functions
Wolfgang Denk (2):
Merge branch 'at91' of git://git.denx.de/u-boot-atmel
Merge branch 'master' of git://git.denx.de/u-boot-ti
arch/arm/cpu/arm1136/start.S | 16 ---
arch/arm/cpu/arm1136/u-boot.lds | 38 ++++---
arch/arm/cpu/arm1176/u-boot.lds | 37 +++----
arch/arm/cpu/arm926ejs/u-boot.lds | 30 +++--
arch/arm/cpu/armv7/omap3/sdrc.c | 7 ++
arch/arm/cpu/armv7/start.S | 24 ----
arch/arm/cpu/armv7/u-boot.lds | 46 +++++----
arch/arm/cpu/pxa/u-boot.lds | 35 ++++--
arch/arm/include/asm/arch-at91/at91_shdwn.h | 38 +++++++
arch/arm/include/asm/arch-at91/at91sam9260.h | 1 +
arch/arm/include/asm/arch-at91/hardware.h | 1 +
arch/arm/include/asm/arch-at91/memory-map.h | 1 +
arch/arm/lib/cache.c | 2 +-
board/isee/igep0020/config.mk | 2 +-
board/isee/igep0020/igep0020.c | 9 ++
board/isee/igep0030/config.mk | 3 +-
board/isee/igep0030/igep0030.c | 9 ++
board/overo/overo.c | 115 ++++++++++++++++++++
board/overo/overo.h | 4 +
board/ti/beagle/beagle.c | 95 ++++++++++++++++
board/ti/beagle/beagle.h | 46 ++++++++-
board/ti/evm/config.mk | 2 +-
board/ti/evm/evm.c | 24 ++++-
board/ti/evm/evm.h | 2 +
drivers/mmc/mmc.c | 148 +++++++++----------------
include/configs/igep0020.h | 9 ++-
include/configs/igep0030.h | 9 ++-
include/configs/omap3_beagle.h | 8 +-
include/configs/omap3_evm.h | 11 ++
include/configs/omap3_overo.h | 7 +-
include/configs/omap4_panda.h | 6 +-
include/configs/omap4_sdp4430.h | 6 +-
nand_spl/board/karo/tx25/u-boot.lds | 40 ++++----
33 files changed, 576 insertions(+), 255 deletions(-)
create mode 100644 arch/arm/include/asm/arch-at91/at91_shdwn.h
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
######## This message was made from 100% recycled electrons. ########
^ permalink raw reply [flat|nested] 40+ messages in thread* [U-Boot] Pull request: u-boot-arm
2010-11-17 19:50 Wolfgang Denk
@ 2010-11-17 19:55 ` Wolfgang Denk
2010-11-17 21:34 ` Loïc Minier
1 sibling, 0 replies; 40+ messages in thread
From: Wolfgang Denk @ 2010-11-17 19:55 UTC (permalink / raw)
To: u-boot
Dear Wolfgang Denk,
In message <20101117195029.907FB14E646@gemini.denx.de> you wrote:
> The following changes since commit d963e84c92a63b4e6c4f2f80482a5ecbe9b24fe0:
>
> Merge branch 'master' of /home/wd/git/u-boot/master (2010-11-12 22:24:06 +0100)
>
> are available in the git repository at:
>
> git://git.denx.de/u-boot-arm.git master
>
> Alagu Sankar (1):
> mmc: Add multi-block read support to the generic mmc driver
>
> Albert Aribaud (2):
> ARM: fix linker file for newer ld support
> tx25: fix linker file for newer ld support
>
> Enric Balletbo i Serra (2):
> ARMV7: OMAP3: Use generic mmc driver on IGEP v2
> ARMV7: OMAP3: Use generic mmc driver on OMAP3 IGEP module
>
> Heiko Schocher (1):
> armv7, beagle: Second SDRAM bank don;t work
>
> Koen Kooi (1):
> ARMV7: OMAP3: Add expansion board detection for Beagle
>
> Reinhard Meyer (2):
> AT91: add 2nd SPI to 9260/9XE/9G20
> AT91: add header file for the Shutdown Controller
>
> Sanjeev Premi (3):
> omap3evm: Support relocation
> omap3evm: Wrap function under CONFIG_USB_OMAP3
> omap3evm: Fix mechanism to identify board revision
>
> Steve Sakoman (5):
> ARMV7: OMAP3: IGEP: Rename TEXT_BASE
> ARMV7: Fix build for non-OMAP3 boards
> ARMV7: OMAP3: Add expansion board detection for Overo
> ARMV7: OMAP: Fix build after introduction of GENERATED_GBL_DATA_SIZE
> mmc: Clean up generic mmc driver multi-block write functions
>
> Wolfgang Denk (2):
> Merge branch 'at91' of git://git.denx.de/u-boot-atmel
> Merge branch 'master' of git://git.denx.de/u-boot-ti
>
> arch/arm/cpu/arm1136/start.S | 16 ---
> arch/arm/cpu/arm1136/u-boot.lds | 38 ++++---
> arch/arm/cpu/arm1176/u-boot.lds | 37 +++----
> arch/arm/cpu/arm926ejs/u-boot.lds | 30 +++--
> arch/arm/cpu/armv7/omap3/sdrc.c | 7 ++
> arch/arm/cpu/armv7/start.S | 24 ----
> arch/arm/cpu/armv7/u-boot.lds | 46 +++++----
> arch/arm/cpu/pxa/u-boot.lds | 35 ++++--
> arch/arm/include/asm/arch-at91/at91_shdwn.h | 38 +++++++
> arch/arm/include/asm/arch-at91/at91sam9260.h | 1 +
> arch/arm/include/asm/arch-at91/hardware.h | 1 +
> arch/arm/include/asm/arch-at91/memory-map.h | 1 +
> arch/arm/lib/cache.c | 2 +-
> board/isee/igep0020/config.mk | 2 +-
> board/isee/igep0020/igep0020.c | 9 ++
> board/isee/igep0030/config.mk | 3 +-
> board/isee/igep0030/igep0030.c | 9 ++
> board/overo/overo.c | 115 ++++++++++++++++++++
> board/overo/overo.h | 4 +
> board/ti/beagle/beagle.c | 95 ++++++++++++++++
> board/ti/beagle/beagle.h | 46 ++++++++-
> board/ti/evm/config.mk | 2 +-
> board/ti/evm/evm.c | 24 ++++-
> board/ti/evm/evm.h | 2 +
> drivers/mmc/mmc.c | 148 +++++++++----------------
> include/configs/igep0020.h | 9 ++-
> include/configs/igep0030.h | 9 ++-
> include/configs/omap3_beagle.h | 8 +-
> include/configs/omap3_evm.h | 11 ++
> include/configs/omap3_overo.h | 7 +-
> include/configs/omap4_panda.h | 6 +-
> include/configs/omap4_sdp4430.h | 6 +-
> nand_spl/board/karo/tx25/u-boot.lds | 40 ++++----
> 33 files changed, 576 insertions(+), 255 deletions(-)
> create mode 100644 arch/arm/include/asm/arch-at91/at91_shdwn.h
Applied.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"The whole world is about three drinks behind." - Humphrey Bogart
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
2010-11-17 19:50 Wolfgang Denk
2010-11-17 19:55 ` Wolfgang Denk
@ 2010-11-17 21:34 ` Loïc Minier
2010-11-17 21:54 ` Wolfgang Denk
1 sibling, 1 reply; 40+ messages in thread
From: Loïc Minier @ 2010-11-17 21:34 UTC (permalink / raw)
To: u-boot
Hey
On Wed, Nov 17, 2010, Wolfgang Denk wrote:
> Sanjeev Premi (3):
> omap3evm: Support relocation
> omap3evm: Wrap function under CONFIG_USB_OMAP3
> omap3evm: Fix mechanism to identify board revision
I was expecting this would fix the build of omap3_evm, but it still
fails for me:
http://hudson.dooz.org/job/u-boot_master/BOARD=omap3_evm/39/console
make[1]: Entering directory `/srv/hudson.dooz.org/home/jobs/u-boot_master/workspace/BOARD/omap3_evm/arch/arm/cpu/armv7'
arm-linux-gnueabi-gcc -D__ASSEMBLY__ -g -Os -fno-common -ffixed-r8 -msoft-float -D__KERNEL__ -DCONFIG_SYS_TEXT_BASE=0x80008000 -I/srv/hudson.dooz.org/home/jobs/u-boot_master/workspace/BOARD/omap3_evm/include -fno-builtin -ffreestanding -nostdinc -isystem /usr/lib/gcc/arm-linux-gnueabi/4.4.5/include -pipe -DCONFIG_ARM -D__ARM__ -marm -mabi=aapcs-linux -mno-thumb-interwork -march=armv5 \
-o start.o start.S -c
start.S: Assembler messages:
start.S:144: Error: constant expression expected -- `ldr sp,=((0x4020FFFC-CONFIG_SYS_GBL_DATA_SIZE))'
make[1]: *** [start.o] Error 1
make[1]: Leaving directory `/srv/hudson.dooz.org/home/jobs/u-boot_master/workspace/BOARD/omap3_evm/arch/arm/cpu/armv7'
Thanks,
--
Lo?c Minier
^ permalink raw reply [flat|nested] 40+ messages in thread* [U-Boot] Pull request: u-boot-arm
2010-11-17 21:34 ` Loïc Minier
@ 2010-11-17 21:54 ` Wolfgang Denk
0 siblings, 0 replies; 40+ messages in thread
From: Wolfgang Denk @ 2010-11-17 21:54 UTC (permalink / raw)
To: u-boot
Dear =?iso-8859-1?Q?Lo=EFc?= Minier,
In message <20101117213409.GA16160@bee.dooz.org> you wrote:
> Hey
>
> On Wed, Nov 17, 2010, Wolfgang Denk wrote:
> > Sanjeev Premi (3):
> > omap3evm: Support relocation
> > omap3evm: Wrap function under CONFIG_USB_OMAP3
> > omap3evm: Fix mechanism to identify board revision
>
> I was expecting this would fix the build of omap3_evm, but it still
> fails for me:
> http://hudson.dooz.org/job/u-boot_master/BOARD=3Domap3_evm/39/console
> make[1]: Entering directory `/srv/hudson.dooz.org/home/jobs/u-boot_master/w=
> orkspace/BOARD/omap3_evm/arch/arm/cpu/armv7'
> arm-linux-gnueabi-gcc -D__ASSEMBLY__ -g -Os -fno-common -ffixed-r8 -ms=
> oft-float -D__KERNEL__ -DCONFIG_SYS_TEXT_BASE=3D0x80008000 -I/srv/hudson.=
> dooz.org/home/jobs/u-boot_master/workspace/BOARD/omap3_evm/include -fno-bui=
> ltin -ffreestanding -nostdinc -isystem /usr/lib/gcc/arm-linux-gnueabi/4.4.5=
> /include -pipe -DCONFIG_ARM -D__ARM__ -marm -mabi=3Daapcs-linux -mno-thum=
> b-interwork -march=3Darmv5 \
> -o start.o start.S -c
> start.S: Assembler messages:
> start.S:144: Error: constant expression expected -- `ldr sp,=3D((0x4020FFFC=
> -CONFIG_SYS_GBL_DATA_SIZE))'
> make[1]: *** [start.o] Error 1
> make[1]: Leaving directory `/srv/hudson.dooz.org/home/jobs/u-boot_master/wo=
> rkspace/BOARD/omap3_evm/arch/arm/cpu/armv7'
CONFIG_SYS_GBL_DATA_SIZE does not exist any more; it now gets
auto-generated. Seems there are a few boards out there that escaped
the change:
-> find * -type f | xargs egrep -l CONFIG_SYS_GBL_DATA_SIZE
include/configs/io.h
include/configs/devkit8000.h
include/configs/omap3_evm.h
include/configs/iocon.h
Patches welcome.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"To take a significant step forward, you must make a series of finite
improvements." - Donald J. Atwood, General Motors
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
@ 2010-10-19 22:08 Wolfgang Denk
2010-10-19 22:14 ` Wolfgang Denk
0 siblings, 1 reply; 40+ messages in thread
From: Wolfgang Denk @ 2010-10-19 22:08 UTC (permalink / raw)
To: u-boot
The following changes since commit 1ba91ba23396005ef7b42381cc21f0baf78d0d60:
dlmalloc.c: Fix gcc alias warning (2010-10-18 22:44:31 +0200)
are available in the git repository at:
git://git.denx.de/u-boot-arm.git master
Albert Aribaud (2):
arm: implement ELF relocations
edminiv2: add support for ELF relocations
Andreas Bie?mann (3):
at91rm9200ek: convert to at91
at91rm9200: enable USB support
at91rm9200ek: enbable USB support
Eric Cooper (1):
Makefile: rename TEXT_BASE to CONFIG_SYS_TEXT_BASE
Heiko Schocher (4):
arm926ejs, magnesium: add support for ELF relocations
arm926ejs, tx25: add support for ELF relocations
armv7, beagle: add support for ELF relocations
arm1136, qong: add support for ELF relocations
Jason Liu (2):
MX5: rename mx51 to mx5
MX5: Remove dead code with ENABLE_IMPRECISE_ABORT
Jens Scharsig (1):
update board EB+CPUx9K2
John Rigby (7):
common/image.c fix length calculation in boot_relocate_fdt
common/image.c remove extra calls to be32_to_cpu in boot_get_fdt
FDT: Add fixup support for multiple banks of memory
FDT: only call boot_get_fdt from generic code
boot: change some arch ifdefs to feature ifdefs
ARM: add flat device tree support
ARM: enable device tree for beagle
Magnus Lilja (1):
i.MX31: Fix Litekit board to use new ARM relocation support.
Marek Vasut (19):
PXA: pxafb: Fix indent problems
PXA: pxa-regs.h cleanup
PXA: pxafb: Add ACX517AKN support
PXA: pxafb: Add support for Sharp LQ038J7DH53
PXA: pxafb: Marvell Littleton LCD definition
common: Enable serial for PXA250
PXA: Palm Tungsten|C Support
PXA: Add initial Palm LifeDrive support
PXA: Voipac270 improvements
PXA: Balloon3 board support
PXA: Add missing MAINTAINERS entries
PXA: Add necessary information for RELOC
PXA: Fix reloc, Push lowlevel init into C code
PXA: Fix vpac270 for Reloc
PXA: Fix ZipitZ2 for Reloc
PXA: Fix Balloon3 for Reloc
PXA: Fix vpac270 OneNAND booter
Build: PXA: Fix Vpac270 build variants
Build: PXA: Fix TrizepsIV build variants
Mikhail Kshevetskiy (4):
PXA: remove unused u-boot.lds from board/vpac270
PXA: cleanup vpac270 config and set CONFIG_SYS_HZ to 1000
PXA: fix environment sector size, kernel and environment location for vpac270
PXA: fix MDREFR[APD] bit setting
Reinhard Meyer (1):
AT91 clock/timer: move static data to global_data struct
Stefano Babic (1):
MX31: add delay between USB port setup and reset
Wolfgang Denk (4):
QONG: fix and update board config file
Merge branch 'master' of git://git.denx.de/u-boot-imx
Merge branch 'elf_reloc'
Merge branch 'at91' of git://git.denx.de/u-boot-atmel
MAINTAINERS | 13 +
MAKEALL | 7 +-
Makefile | 19 +-
README | 13 +
arch/arm/config.mk | 12 +-
arch/arm/cpu/arm1136/start.S | 171 +-
arch/arm/cpu/arm1136/u-boot.lds | 15 +-
arch/arm/cpu/arm926ejs/at91/clock.c | 55 +-
arch/arm/cpu/arm926ejs/at91/timer.c | 85 +-
arch/arm/cpu/arm926ejs/start.S | 162 +-
arch/arm/cpu/arm926ejs/u-boot.lds | 26 +-
arch/arm/cpu/armv7/{mx51 => mx5}/Makefile | 0
arch/arm/cpu/armv7/{mx51 => mx5}/clock.c | 42 +-
arch/arm/cpu/armv7/{mx51 => mx5}/iomux.c | 2 +-
arch/arm/cpu/armv7/{mx51 => mx5}/lowlevel_init.S | 14 -
arch/arm/cpu/armv7/{mx51 => mx5}/soc.c | 28 +-
arch/arm/cpu/armv7/{mx51 => mx5}/speed.c | 0
arch/arm/cpu/armv7/{mx51 => mx5}/timer.c | 8 +-
arch/arm/cpu/armv7/{mx51 => mx5}/u-boot.lds | 0
arch/arm/cpu/armv7/start.S | 131 +-
arch/arm/cpu/armv7/u-boot.lds | 7 +
arch/arm/cpu/pxa/cpu.c | 255 ++-
arch/arm/cpu/pxa/i2c.c | 69 +-
arch/arm/cpu/pxa/pxafb.c | 365 ++-
arch/arm/cpu/pxa/start.S | 344 +--
arch/arm/cpu/pxa/timer.c | 7 +-
arch/arm/cpu/pxa/usb.c | 61 +-
arch/arm/include/asm/arch-at91/hardware.h | 1 +
.../asm/{arch-mx51 => arch-mx5}/asm-offsets.h | 0
.../include/asm/{arch-mx51 => arch-mx5}/clock.h | 0
.../include/asm/{arch-mx51 => arch-mx5}/crm_regs.h | 0
.../include/asm/{arch-mx51 => arch-mx5}/imx-regs.h | 0
.../include/asm/{arch-mx51 => arch-mx5}/iomux.h | 8 +-
.../mx51_pins.h => arch-mx5/mx5x_pins.h} | 6 +-
.../asm/{arch-mx51 => arch-mx5}/sys_proto.h | 0
arch/arm/include/asm/arch-pxa/hardware.h | 61 +-
arch/arm/include/asm/arch-pxa/macro.h | 20 +-
arch/arm/include/asm/arch-pxa/pxa-regs.h | 2688 +++++++++++---------
arch/arm/include/asm/config.h | 5 +-
arch/arm/include/asm/global_data.h | 14 +
arch/arm/include/asm/u-boot-arm.h | 14 +-
arch/arm/lib/board.c | 8 +-
arch/arm/lib/bootm.c | 137 +-
arch/arm/lib/cache.c | 2 +-
arch/m68k/include/asm/config.h | 3 +
arch/microblaze/lib/bootm.c | 14 +-
arch/nios2/lib/bootm.c | 8 +-
arch/powerpc/include/asm/config.h | 3 +
arch/sparc/include/asm/config.h | 1 +
board/BuS/eb_cpux9k2/config.mk | 1 -
board/BuS/eb_cpux9k2/cpux9k2.c | 7 +-
board/LaCie/edminiv2/config.mk | 3 +-
board/atmel/at91rm9200ek/Makefile | 5 -
board/atmel/at91rm9200ek/at91rm9200ek.c | 60 +-
board/atmel/at91rm9200ek/config.mk | 3 +-
board/atmel/at91rm9200ek/led.c | 58 +-
board/atmel/at91rm9200ek/mux.c | 38 -
.../arm/cpu/armv7/mx51 => board/balloon3}/Makefile | 27 +-
board/balloon3/balloon3.c | 238 ++
board/colibri_pxa270/colibri_pxa270.c | 33 +-
board/cradle/cradle.c | 5 +-
board/cradle/lowlevel_init.S | 4 +-
board/csb226/csb226.c | 13 +-
board/delta/delta.c | 37 +-
board/delta/nand.c | 110 +-
board/freescale/mx51evk/mx51evk.c | 2 +-
board/innokom/innokom.c | 14 +-
board/karo/tx25/config.mk | 2 +-
board/logicpd/imx27lite/config.mk | 4 +
board/logicpd/imx31_litekit/config.mk | 2 +-
board/logicpd/imx31_litekit/imx31_litekit.c | 10 +-
{arch/arm/cpu/armv7/mx51 => board/palmld}/Makefile | 27 +-
board/palmld/config.mk | 1 +
board/{zipitz2 => palmld}/lowlevel_init.S | 9 +-
board/palmld/palmld.c | 69 +
board/{vpac270 => palmld}/u-boot.lds | 7 +-
{arch/arm/cpu/armv7/mx51 => board/palmtc}/Makefile | 27 +-
board/palmtc/config.mk | 1 +
board/{vpac270 => palmtc}/lowlevel_init.S | 3 +-
.../at91rm9200ek/partition.c => palmtc/palmtc.c} | 61 +-
.../at91rm9200ek/misc.c => palmtc/u-boot.lds} | 50 +-
board/pxa255_idp/pxa_idp.c | 27 +-
board/trizepsiv/conxs.c | 35 +-
board/ttcontrol/vision2/vision2.c | 2 +-
board/vpac270/Makefile | 17 +-
board/vpac270/config.mk | 1 -
board/vpac270/vpac270.c | 92 +-
board/wepep250/wepep250.c | 11 +-
board/zipitz2/Makefile | 10 +-
board/zipitz2/config.mk | 1 -
board/zipitz2/zipitz2.c | 57 +-
board/zylonite/nand.c | 110 +-
boards.cfg | 14 +-
common/cmd_bootm.c | 6 +-
common/fdt_support.c | 86 +-
common/image.c | 16 +-
common/serial.c | 2 +-
doc/README.arm-relocation | 222 +--
drivers/mmc/pxa_mmc.c | 98 +-
drivers/serial/serial_pxa.c | 94 +-
drivers/usb/host/ehci-mxc.c | 2 +
include/configs/at91rm9200ek.h | 286 +--
include/configs/balloon3.h | 274 ++
include/configs/cerf250.h | 3 +
include/configs/colibri_pxa270.h | 3 +
include/configs/cradle.h | 5 +-
include/configs/csb226.h | 3 +
include/configs/delta.h | 4 +
include/configs/eb_cpux9k2.h | 23 +-
include/configs/edminiv2.h | 5 +
include/configs/imx31_litekit.h | 7 +
include/configs/innokom.h | 3 +
include/configs/lubbock.h | 3 +
include/configs/mx51evk.h | 4 +-
include/configs/omap3_beagle.h | 9 +
include/configs/palmld.h | 276 ++
include/configs/palmtc.h | 248 ++
include/configs/pleb2.h | 3 +
include/configs/pxa255_idp.h | 3 +
include/configs/qong.h | 32 +-
include/configs/trizepsiv.h | 3 +
include/configs/tx25.h | 2 +-
include/configs/vision2.h | 4 +-
include/configs/vpac270.h | 138 +-
include/configs/wepep250.h | 4 +
include/configs/xaeniax.h | 3 +
include/configs/xm250.h | 3 +
include/configs/xsengine.h | 3 +
include/configs/zipitz2.h | 10 +-
include/configs/zylonite.h | 3 +
include/fdt_support.h | 1 +
include/image.h | 9 +-
nand_spl/board/karo/tx25/u-boot.lds | 13 +
onenand_ipl/board/vpac270/Makefile | 5 +-
134 files changed, 4843 insertions(+), 3290 deletions(-)
copy arch/arm/cpu/armv7/{mx51 => mx5}/Makefile (100%)
rename arch/arm/cpu/armv7/{mx51 => mx5}/clock.c (85%)
rename arch/arm/cpu/armv7/{mx51 => mx5}/iomux.c (99%)
rename arch/arm/cpu/armv7/{mx51 => mx5}/lowlevel_init.S (95%)
rename arch/arm/cpu/armv7/{mx51 => mx5}/soc.c (81%)
rename arch/arm/cpu/armv7/{mx51 => mx5}/speed.c (100%)
rename arch/arm/cpu/armv7/{mx51 => mx5}/timer.c (92%)
rename arch/arm/cpu/armv7/{mx51 => mx5}/u-boot.lds (100%)
rename arch/arm/include/asm/{arch-mx51 => arch-mx5}/asm-offsets.h (100%)
rename arch/arm/include/asm/{arch-mx51 => arch-mx5}/clock.h (100%)
rename arch/arm/include/asm/{arch-mx51 => arch-mx5}/crm_regs.h (100%)
rename arch/arm/include/asm/{arch-mx51 => arch-mx5}/imx-regs.h (100%)
rename arch/arm/include/asm/{arch-mx51 => arch-mx5}/iomux.h (98%)
rename arch/arm/include/asm/{arch-mx51/mx51_pins.h => arch-mx5/mx5x_pins.h} (99%)
rename arch/arm/include/asm/{arch-mx51 => arch-mx5}/sys_proto.h (100%)
delete mode 100644 board/BuS/eb_cpux9k2/config.mk
delete mode 100644 board/atmel/at91rm9200ek/mux.c
copy {arch/arm/cpu/armv7/mx51 => board/balloon3}/Makefile (70%)
create mode 100644 board/balloon3/balloon3.c
copy {arch/arm/cpu/armv7/mx51 => board/palmld}/Makefile (70%)
create mode 100644 board/palmld/config.mk
rename board/{zipitz2 => palmld}/lowlevel_init.S (90%)
create mode 100644 board/palmld/palmld.c
rename board/{vpac270 => palmld}/u-boot.lds (90%)
rename {arch/arm/cpu/armv7/mx51 => board/palmtc}/Makefile (70%)
create mode 100644 board/palmtc/config.mk
rename board/{vpac270 => palmtc}/lowlevel_init.S (95%)
rename board/{atmel/at91rm9200ek/partition.c => palmtc/palmtc.c} (50%)
rename board/{atmel/at91rm9200ek/misc.c => palmtc/u-boot.lds} (57%)
delete mode 100644 board/vpac270/config.mk
delete mode 100644 board/zipitz2/config.mk
create mode 100644 include/configs/balloon3.h
create mode 100644 include/configs/palmld.h
create mode 100644 include/configs/palmtc.h
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
He'd heard her use that sweet, innocent tone of voice before. It
meant that, pretty soon, there was going to be trouble.
- Terry Pratchett, _Truckers_
^ permalink raw reply [flat|nested] 40+ messages in thread* [U-Boot] Pull request: u-boot-arm
2010-10-19 22:08 Wolfgang Denk
@ 2010-10-19 22:14 ` Wolfgang Denk
0 siblings, 0 replies; 40+ messages in thread
From: Wolfgang Denk @ 2010-10-19 22:14 UTC (permalink / raw)
To: u-boot
In message <20101019220814.50EA1136320@gemini.denx.de> I wrote:
> The following changes since commit 1ba91ba23396005ef7b42381cc21f0baf78d0d60:
>
> dlmalloc.c: Fix gcc alias warning (2010-10-18 22:44:31 +0200)
>
> are available in the git repository at:
> git://git.denx.de/u-boot-arm.git master
>
> Albert Aribaud (2):
> arm: implement ELF relocations
> edminiv2: add support for ELF relocations
>
> Andreas Bie?mann (3):
> at91rm9200ek: convert to at91
> at91rm9200: enable USB support
> at91rm9200ek: enbable USB support
>
> Eric Cooper (1):
> Makefile: rename TEXT_BASE to CONFIG_SYS_TEXT_BASE
>
> Heiko Schocher (4):
> arm926ejs, magnesium: add support for ELF relocations
> arm926ejs, tx25: add support for ELF relocations
> armv7, beagle: add support for ELF relocations
> arm1136, qong: add support for ELF relocations
>
> Jason Liu (2):
> MX5: rename mx51 to mx5
> MX5: Remove dead code with ENABLE_IMPRECISE_ABORT
>
> Jens Scharsig (1):
> update board EB+CPUx9K2
>
> John Rigby (7):
> common/image.c fix length calculation in boot_relocate_fdt
> common/image.c remove extra calls to be32_to_cpu in boot_get_fdt
> FDT: Add fixup support for multiple banks of memory
> FDT: only call boot_get_fdt from generic code
> boot: change some arch ifdefs to feature ifdefs
> ARM: add flat device tree support
> ARM: enable device tree for beagle
>
> Magnus Lilja (1):
> i.MX31: Fix Litekit board to use new ARM relocation support.
>
> Marek Vasut (19):
> PXA: pxafb: Fix indent problems
> PXA: pxa-regs.h cleanup
> PXA: pxafb: Add ACX517AKN support
> PXA: pxafb: Add support for Sharp LQ038J7DH53
> PXA: pxafb: Marvell Littleton LCD definition
> common: Enable serial for PXA250
> PXA: Palm Tungsten|C Support
> PXA: Add initial Palm LifeDrive support
> PXA: Voipac270 improvements
> PXA: Balloon3 board support
> PXA: Add missing MAINTAINERS entries
> PXA: Add necessary information for RELOC
> PXA: Fix reloc, Push lowlevel init into C code
> PXA: Fix vpac270 for Reloc
> PXA: Fix ZipitZ2 for Reloc
> PXA: Fix Balloon3 for Reloc
> PXA: Fix vpac270 OneNAND booter
> Build: PXA: Fix Vpac270 build variants
> Build: PXA: Fix TrizepsIV build variants
>
> Mikhail Kshevetskiy (4):
> PXA: remove unused u-boot.lds from board/vpac270
> PXA: cleanup vpac270 config and set CONFIG_SYS_HZ to 1000
> PXA: fix environment sector size, kernel and environment location for> vpac270
> PXA: fix MDREFR[APD] bit setting
>
> Reinhard Meyer (1):
> AT91 clock/timer: move static data to global_data struct
>
> Stefano Babic (1):
> MX31: add delay between USB port setup and reset
>
> Wolfgang Denk (4):
> QONG: fix and update board config file
> Merge branch 'master' of git://git.denx.de/u-boot-imx
> Merge branch 'elf_reloc'
> Merge branch 'at91' of git://git.denx.de/u-boot-atmel
>
> MAINTAINERS | 13 +
> MAKEALL | 7 +-
> Makefile | 19 +-
> README | 13 +
> arch/arm/config.mk | 12 +-
> arch/arm/cpu/arm1136/start.S | 171 +-
> arch/arm/cpu/arm1136/u-boot.lds | 15 +-
> arch/arm/cpu/arm926ejs/at91/clock.c | 55 +-
> arch/arm/cpu/arm926ejs/at91/timer.c | 85 +-
> arch/arm/cpu/arm926ejs/start.S | 162 +-
> arch/arm/cpu/arm926ejs/u-boot.lds | 26 +-
> arch/arm/cpu/armv7/{mx51 => mx5}/Makefile | 0
> arch/arm/cpu/armv7/{mx51 => mx5}/clock.c | 42 +-
> arch/arm/cpu/armv7/{mx51 => mx5}/iomux.c | 2 +-
> arch/arm/cpu/armv7/{mx51 => mx5}/lowlevel_init.S | 14 -
> arch/arm/cpu/armv7/{mx51 => mx5}/soc.c | 28 +-
> arch/arm/cpu/armv7/{mx51 => mx5}/speed.c | 0
> arch/arm/cpu/armv7/{mx51 => mx5}/timer.c | 8 +-
> arch/arm/cpu/armv7/{mx51 => mx5}/u-boot.lds | 0
> arch/arm/cpu/armv7/start.S | 131 +-
> arch/arm/cpu/armv7/u-boot.lds | 7 +
> arch/arm/cpu/pxa/cpu.c | 255 ++-
> arch/arm/cpu/pxa/i2c.c | 69 +-
> arch/arm/cpu/pxa/pxafb.c | 365 ++-
> arch/arm/cpu/pxa/start.S | 344 +--
> arch/arm/cpu/pxa/timer.c | 7 +-
> arch/arm/cpu/pxa/usb.c | 61 +-
> arch/arm/include/asm/arch-at91/hardware.h | 1 +
> .../asm/{arch-mx51 => arch-mx5}/asm-offsets.h | 0
> .../include/asm/{arch-mx51 => arch-mx5}/clock.h | 0
> .../include/asm/{arch-mx51 => arch-mx5}/crm_regs.h | 0
> .../include/asm/{arch-mx51 => arch-mx5}/imx-regs.h | 0
> .../include/asm/{arch-mx51 => arch-mx5}/iomux.h | 8 +-
> .../mx51_pins.h => arch-mx5/mx5x_pins.h} | 6 +-
> .../asm/{arch-mx51 => arch-mx5}/sys_proto.h | 0
> arch/arm/include/asm/arch-pxa/hardware.h | 61 +-
> arch/arm/include/asm/arch-pxa/macro.h | 20 +-
> arch/arm/include/asm/arch-pxa/pxa-regs.h | 2688 +++++++++++-----> ----
> arch/arm/include/asm/config.h | 5 +-
> arch/arm/include/asm/global_data.h | 14 +
> arch/arm/include/asm/u-boot-arm.h | 14 +-
> arch/arm/lib/board.c | 8 +-
> arch/arm/lib/bootm.c | 137 +-
> arch/arm/lib/cache.c | 2 +-
> arch/m68k/include/asm/config.h | 3 +
> arch/microblaze/lib/bootm.c | 14 +-
> arch/nios2/lib/bootm.c | 8 +-
> arch/powerpc/include/asm/config.h | 3 +
> arch/sparc/include/asm/config.h | 1 +
> board/BuS/eb_cpux9k2/config.mk | 1 -
> board/BuS/eb_cpux9k2/cpux9k2.c | 7 +-
> board/LaCie/edminiv2/config.mk | 3 +-
> board/atmel/at91rm9200ek/Makefile | 5 -
> board/atmel/at91rm9200ek/at91rm9200ek.c | 60 +-
> board/atmel/at91rm9200ek/config.mk | 3 +-
> board/atmel/at91rm9200ek/led.c | 58 +-
> board/atmel/at91rm9200ek/mux.c | 38 -
> .../arm/cpu/armv7/mx51 => board/balloon3}/Makefile | 27 +-
> board/balloon3/balloon3.c | 238 ++
> board/colibri_pxa270/colibri_pxa270.c | 33 +-
> board/cradle/cradle.c | 5 +-
> board/cradle/lowlevel_init.S | 4 +-
> board/csb226/csb226.c | 13 +-
> board/delta/delta.c | 37 +-
> board/delta/nand.c | 110 +-
> board/freescale/mx51evk/mx51evk.c | 2 +-
> board/innokom/innokom.c | 14 +-
> board/karo/tx25/config.mk | 2 +-
> board/logicpd/imx27lite/config.mk | 4 +
> board/logicpd/imx31_litekit/config.mk | 2 +-
> board/logicpd/imx31_litekit/imx31_litekit.c | 10 +-
> {arch/arm/cpu/armv7/mx51 => board/palmld}/Makefile | 27 +-
> board/palmld/config.mk | 1 +
> board/{zipitz2 => palmld}/lowlevel_init.S | 9 +-
> board/palmld/palmld.c | 69 +
> board/{vpac270 => palmld}/u-boot.lds | 7 +-
> {arch/arm/cpu/armv7/mx51 => board/palmtc}/Makefile | 27 +-
> board/palmtc/config.mk | 1 +
> board/{vpac270 => palmtc}/lowlevel_init.S | 3 +-
> .../at91rm9200ek/partition.c => palmtc/palmtc.c} | 61 +-
> .../at91rm9200ek/misc.c => palmtc/u-boot.lds} | 50 +-
> board/pxa255_idp/pxa_idp.c | 27 +-
> board/trizepsiv/conxs.c | 35 +-
> board/ttcontrol/vision2/vision2.c | 2 +-
> board/vpac270/Makefile | 17 +-
> board/vpac270/config.mk | 1 -
> board/vpac270/vpac270.c | 92 +-
> board/wepep250/wepep250.c | 11 +-
> board/zipitz2/Makefile | 10 +-
> board/zipitz2/config.mk | 1 -
> board/zipitz2/zipitz2.c | 57 +-
> board/zylonite/nand.c | 110 +-
> boards.cfg | 14 +-
> common/cmd_bootm.c | 6 +-
> common/fdt_support.c | 86 +-
> common/image.c | 16 +-
> common/serial.c | 2 +-
> doc/README.arm-relocation | 222 +--
> drivers/mmc/pxa_mmc.c | 98 +-
> drivers/serial/serial_pxa.c | 94 +-
> drivers/usb/host/ehci-mxc.c | 2 +
> include/configs/at91rm9200ek.h | 286 +--
> include/configs/balloon3.h | 274 ++
> include/configs/cerf250.h | 3 +
> include/configs/colibri_pxa270.h | 3 +
> include/configs/cradle.h | 5 +-
> include/configs/csb226.h | 3 +
> include/configs/delta.h | 4 +
> include/configs/eb_cpux9k2.h | 23 +-
> include/configs/edminiv2.h | 5 +
> include/configs/imx31_litekit.h | 7 +
> include/configs/innokom.h | 3 +
> include/configs/lubbock.h | 3 +
> include/configs/mx51evk.h | 4 +-
> include/configs/omap3_beagle.h | 9 +
> include/configs/palmld.h | 276 ++
> include/configs/palmtc.h | 248 ++
> include/configs/pleb2.h | 3 +
> include/configs/pxa255_idp.h | 3 +
> include/configs/qong.h | 32 +-
> include/configs/trizepsiv.h | 3 +
> include/configs/tx25.h | 2 +-
> include/configs/vision2.h | 4 +-
> include/configs/vpac270.h | 138 +-
> include/configs/wepep250.h | 4 +
> include/configs/xaeniax.h | 3 +
> include/configs/xm250.h | 3 +
> include/configs/xsengine.h | 3 +
> include/configs/zipitz2.h | 10 +-
> include/configs/zylonite.h | 3 +
> include/fdt_support.h | 1 +
> include/image.h | 9 +-
> nand_spl/board/karo/tx25/u-boot.lds | 13 +
> onenand_ipl/board/vpac270/Makefile | 5 +-
> 134 files changed, 4843 insertions(+), 3290 deletions(-)
> copy arch/arm/cpu/armv7/{mx51 => mx5}/Makefile (100%)
> rename arch/arm/cpu/armv7/{mx51 => mx5}/clock.c (85%)
> rename arch/arm/cpu/armv7/{mx51 => mx5}/iomux.c (99%)
> rename arch/arm/cpu/armv7/{mx51 => mx5}/lowlevel_init.S (95%)
> rename arch/arm/cpu/armv7/{mx51 => mx5}/soc.c (81%)
> rename arch/arm/cpu/armv7/{mx51 => mx5}/speed.c (100%)
> rename arch/arm/cpu/armv7/{mx51 => mx5}/timer.c (92%)
> rename arch/arm/cpu/armv7/{mx51 => mx5}/u-boot.lds (100%)
> rename arch/arm/include/asm/{arch-mx51 => arch-mx5}/asm-offsets.h (100%)
> rename arch/arm/include/asm/{arch-mx51 => arch-mx5}/clock.h (100%)
> rename arch/arm/include/asm/{arch-mx51 => arch-mx5}/crm_regs.h (100%)
> rename arch/arm/include/asm/{arch-mx51 => arch-mx5}/imx-regs.h (100%)
> rename arch/arm/include/asm/{arch-mx51 => arch-mx5}/iomux.h (98%)
> rename arch/arm/include/asm/{arch-mx51/mx51_pins.h => arch-mx5/mx5x_pins> .h} (99%)
> rename arch/arm/include/asm/{arch-mx51 => arch-mx5}/sys_proto.h (100%)
> delete mode 100644 board/BuS/eb_cpux9k2/config.mk
> delete mode 100644 board/atmel/at91rm9200ek/mux.c
> copy {arch/arm/cpu/armv7/mx51 => board/balloon3}/Makefile (70%)
> create mode 100644 board/balloon3/balloon3.c
> copy {arch/arm/cpu/armv7/mx51 => board/palmld}/Makefile (70%)
> create mode 100644 board/palmld/config.mk
> rename board/{zipitz2 => palmld}/lowlevel_init.S (90%)
> create mode 100644 board/palmld/palmld.c
> rename board/{vpac270 => palmld}/u-boot.lds (90%)
> rename {arch/arm/cpu/armv7/mx51 => board/palmtc}/Makefile (70%)
> create mode 100644 board/palmtc/config.mk
> rename board/{vpac270 => palmtc}/lowlevel_init.S (95%)
> rename board/{atmel/at91rm9200ek/partition.c => palmtc/palmtc.c} (50%)
> rename board/{atmel/at91rm9200ek/misc.c => palmtc/u-boot.lds} (57%)
> delete mode 100644 board/vpac270/config.mk
> delete mode 100644 board/zipitz2/config.mk
> create mode 100644 include/configs/balloon3.h
> create mode 100644 include/configs/palmld.h
> create mode 100644 include/configs/palmtc.h
Applied.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
If the facts don't fit the theory, change the facts.
-- Albert Einstein
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
@ 2010-10-17 18:24 Wolfgang Denk
2010-10-17 18:36 ` Wolfgang Denk
0 siblings, 1 reply; 40+ messages in thread
From: Wolfgang Denk @ 2010-10-17 18:24 UTC (permalink / raw)
To: u-boot
The following changes since commit e1b4c57096b87b4ada56df4154d9acee6a59141f:
Merge branch 'master' of git://git.denx.de/u-boot-arm (2010-10-13 20:59:47 +0200)
are available in the git repository at:
git://git.denx.de/u-boot-arm.git master
Ben Gardiner (7):
davinci_nand, trivial : use symbolic ECC start command
da850evm : enable NAND even when not in NAND boot mode
da850evm: setup the NAND flash timings
da850evm: setup NAND support under CONFIG_USE_NAND
da850evm: add mtdpart and ubi commands with NAND support
da850evm: basic MII EMAC support
da850evm: fix linux bootparam address
Enric Balletbo i Serra (3):
OMAP3: SDRC: Introduce Numonyx DDR type
OMAP3: Add support for the IGEP v2 board.
OMAP3: Add support for the OMAP3 IGEP module.
Loic Minier (1):
mx51evk: add u-boot.imx to ALL target
Stefano Babic (6):
FPGA: add support for downloading Lattice bitstream
MX31: Adding missing iomux pin to MX.31 registers
MX31: Add support to update FPGA bitstream
MX31: add support for setting pin pads
MX31: Add support for MXC EHCI controller
MX31: Add USB Host support to the QONG board
Steve Sakoman (8):
env_mmc: Fix crashing bug encountered after enabling ARM relocation
ARMV7: OMAP: Use default vendor/product ID for USB gadget
ARMV7: OMAP4: Use generic mmc driver on Beagle
ARMV7: OMAP4: Use generic mmc driver on Overo
ARMV7: OMAP3: Implement relocation for Overo
ARMV7: OMAP3: Enable cache support on Overo
ARMV7: OMAP3: Fix bug in get_sdr_cs_offset()
ARMV7: OMAP4: Implement relocation for Panda and OMAP4430SDP
Sukumar Ghorai (5):
MMC: Fix for capacity calculation on eMMC
ARMV7: OMAP: Add new mmc driver compatible with CONFIG_GENERIC_MMC
ARMV7: OMAP4: Use generic mmc driver on Panda
ARMV7: OMAP4: Use generic mmc driver on SDP4430
ARMV7: OMAP4: Enable saveenv to eMMC for SDP4430
Wolfgang Denk (1):
Merge branch 'master' of git://git.denx.de/u-boot-imx
MAINTAINERS | 5 +
MAKEALL | 2 +
arch/arm/cpu/arm1136/mx31/generic.c | 17 +
arch/arm/cpu/armv7/omap3/sdrc.c | 2 +-
arch/arm/cpu/armv7/omap4/board.c | 5 +
arch/arm/include/asm/arch-mx31/mx31-regs.h | 411 +++
arch/arm/include/asm/arch-omap3/mem.h | 43 +
arch/arm/include/asm/arch-omap3/mmc_host_def.h | 10 +
arch/arm/include/asm/arch-omap4/mmc_host_def.h | 10 +
arch/arm/lib/board.c | 10 +-
board/davedenx/qong/Makefile | 2 +-
board/davedenx/qong/fpga.c | 95 +
board/davedenx/qong/qong.c | 44 +
board/davedenx/qong/qong_fpga.h | 3 +-
board/davinci/da8xxevm/da850evm.c | 89 +
board/freescale/mx51evk/config.mk | 1 +
board/isee/igep0020/Makefile | 49 +
board/isee/igep0020/config.mk | 33 +
board/isee/igep0020/igep0020.c | 129 +
board/isee/igep0020/igep0020.h | 156 ++
board/isee/igep0030/Makefile | 49 +
board/isee/igep0030/config.mk | 34 +
board/isee/igep0030/igep0030.c | 71 +
board/isee/igep0030/igep0030.h | 147 ++
board/overo/config.mk | 2 +-
board/overo/overo.c | 9 +
board/ti/beagle/beagle.c | 9 +
board/ti/panda/config.mk | 4 +-
board/ti/panda/panda.c | 9 +
board/ti/sdp4430/config.mk | 3 +-
board/ti/sdp4430/sdp.c | 10 +
boards.cfg | 2 +
common/env_mmc.c | 17 +-
drivers/fpga/Makefile | 1 +
drivers/fpga/fpga.c | 11 +
drivers/fpga/ivm_core.c | 3167 ++++++++++++++++++++++++
drivers/fpga/lattice.c | 399 +++
drivers/mmc/Makefile | 1 +
drivers/mmc/mmc.c | 11 +
drivers/mmc/omap_hsmmc.c | 415 ++++
drivers/mtd/nand/davinci_nand.c | 3 +-
drivers/usb/host/Makefile | 1 +
drivers/usb/host/ehci-mxc.c | 130 +
drivers/video/mx3fb.c | 31 -
include/configs/da850evm.h | 54 +-
include/configs/igep0020.h | 228 ++
include/configs/igep0030.h | 215 ++
include/configs/omap3_beagle.h | 15 +-
include/configs/omap3_overo.h | 14 +-
include/configs/omap4_panda.h | 23 +-
include/configs/omap4_sdp4430.h | 35 +-
include/configs/qong.h | 21 +-
include/fpga.h | 1 +
include/lattice.h | 319 +++
54 files changed, 6472 insertions(+), 105 deletions(-)
create mode 100644 board/davedenx/qong/fpga.c
create mode 100644 board/isee/igep0020/Makefile
create mode 100644 board/isee/igep0020/config.mk
create mode 100644 board/isee/igep0020/igep0020.c
create mode 100644 board/isee/igep0020/igep0020.h
create mode 100644 board/isee/igep0030/Makefile
create mode 100644 board/isee/igep0030/config.mk
create mode 100644 board/isee/igep0030/igep0030.c
create mode 100644 board/isee/igep0030/igep0030.h
create mode 100755 drivers/fpga/ivm_core.c
create mode 100644 drivers/fpga/lattice.c
create mode 100644 drivers/mmc/omap_hsmmc.c
create mode 100644 drivers/usb/host/ehci-mxc.c
create mode 100644 include/configs/igep0020.h
create mode 100644 include/configs/igep0030.h
create mode 100755 include/lattice.h
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Documentation is like sex: when it is good, it is very, very good;
and when it is bad, it is better than nothing. - Dick Brandon
^ permalink raw reply [flat|nested] 40+ messages in thread* [U-Boot] Pull request: u-boot-arm
2010-10-17 18:24 Wolfgang Denk
@ 2010-10-17 18:36 ` Wolfgang Denk
0 siblings, 0 replies; 40+ messages in thread
From: Wolfgang Denk @ 2010-10-17 18:36 UTC (permalink / raw)
To: u-boot
In message <20101017182418.DE8EF13558AD@gemini.denx.de> you wrote:
> The following changes since commit e1b4c57096b87b4ada56df4154d9acee6a59141f:
>
> Merge branch 'master' of git://git.denx.de/u-boot-arm (2010-10-13 20:59:47 +0200)
>
> are available in the git repository at:
>
> git://git.denx.de/u-boot-arm.git master
>
> Ben Gardiner (7):
> davinci_nand, trivial : use symbolic ECC start command
> da850evm : enable NAND even when not in NAND boot mode
> da850evm: setup the NAND flash timings
> da850evm: setup NAND support under CONFIG_USE_NAND
> da850evm: add mtdpart and ubi commands with NAND support
> da850evm: basic MII EMAC support
> da850evm: fix linux bootparam address
>
> Enric Balletbo i Serra (3):
> OMAP3: SDRC: Introduce Numonyx DDR type
> OMAP3: Add support for the IGEP v2 board.
> OMAP3: Add support for the OMAP3 IGEP module.
>
> Loic Minier (1):
> mx51evk: add u-boot.imx to ALL target
>
> Stefano Babic (6):
> FPGA: add support for downloading Lattice bitstream
> MX31: Adding missing iomux pin to MX.31 registers
> MX31: Add support to update FPGA bitstream
> MX31: add support for setting pin pads
> MX31: Add support for MXC EHCI controller
> MX31: Add USB Host support to the QONG board
>
> Steve Sakoman (8):
> env_mmc: Fix crashing bug encountered after enabling ARM relocation
> ARMV7: OMAP: Use default vendor/product ID for USB gadget
> ARMV7: OMAP4: Use generic mmc driver on Beagle
> ARMV7: OMAP4: Use generic mmc driver on Overo
> ARMV7: OMAP3: Implement relocation for Overo
> ARMV7: OMAP3: Enable cache support on Overo
> ARMV7: OMAP3: Fix bug in get_sdr_cs_offset()
> ARMV7: OMAP4: Implement relocation for Panda and OMAP4430SDP
>
> Sukumar Ghorai (5):
> MMC: Fix for capacity calculation on eMMC
> ARMV7: OMAP: Add new mmc driver compatible with CONFIG_GENERIC_MMC
> ARMV7: OMAP4: Use generic mmc driver on Panda
> ARMV7: OMAP4: Use generic mmc driver on SDP4430
> ARMV7: OMAP4: Enable saveenv to eMMC for SDP4430
>
> Wolfgang Denk (1):
> Merge branch 'master' of git://git.denx.de/u-boot-imx
>
> MAINTAINERS | 5 +
> MAKEALL | 2 +
> arch/arm/cpu/arm1136/mx31/generic.c | 17 +
> arch/arm/cpu/armv7/omap3/sdrc.c | 2 +-
> arch/arm/cpu/armv7/omap4/board.c | 5 +
> arch/arm/include/asm/arch-mx31/mx31-regs.h | 411 +++
> arch/arm/include/asm/arch-omap3/mem.h | 43 +
> arch/arm/include/asm/arch-omap3/mmc_host_def.h | 10 +
> arch/arm/include/asm/arch-omap4/mmc_host_def.h | 10 +
> arch/arm/lib/board.c | 10 +-
> board/davedenx/qong/Makefile | 2 +-
> board/davedenx/qong/fpga.c | 95 +
> board/davedenx/qong/qong.c | 44 +
> board/davedenx/qong/qong_fpga.h | 3 +-
> board/davinci/da8xxevm/da850evm.c | 89 +
> board/freescale/mx51evk/config.mk | 1 +
> board/isee/igep0020/Makefile | 49 +
> board/isee/igep0020/config.mk | 33 +
> board/isee/igep0020/igep0020.c | 129 +
> board/isee/igep0020/igep0020.h | 156 ++
> board/isee/igep0030/Makefile | 49 +
> board/isee/igep0030/config.mk | 34 +
> board/isee/igep0030/igep0030.c | 71 +
> board/isee/igep0030/igep0030.h | 147 ++
> board/overo/config.mk | 2 +-
> board/overo/overo.c | 9 +
> board/ti/beagle/beagle.c | 9 +
> board/ti/panda/config.mk | 4 +-
> board/ti/panda/panda.c | 9 +
> board/ti/sdp4430/config.mk | 3 +-
> board/ti/sdp4430/sdp.c | 10 +
> boards.cfg | 2 +
> common/env_mmc.c | 17 +-
> drivers/fpga/Makefile | 1 +
> drivers/fpga/fpga.c | 11 +
> drivers/fpga/ivm_core.c | 3167 ++++++++++++++++++++++++
> drivers/fpga/lattice.c | 399 +++
> drivers/mmc/Makefile | 1 +
> drivers/mmc/mmc.c | 11 +
> drivers/mmc/omap_hsmmc.c | 415 ++++
> drivers/mtd/nand/davinci_nand.c | 3 +-
> drivers/usb/host/Makefile | 1 +
> drivers/usb/host/ehci-mxc.c | 130 +
> drivers/video/mx3fb.c | 31 -
> include/configs/da850evm.h | 54 +-
> include/configs/igep0020.h | 228 ++
> include/configs/igep0030.h | 215 ++
> include/configs/omap3_beagle.h | 15 +-
> include/configs/omap3_overo.h | 14 +-
> include/configs/omap4_panda.h | 23 +-
> include/configs/omap4_sdp4430.h | 35 +-
> include/configs/qong.h | 21 +-
> include/fpga.h | 1 +
> include/lattice.h | 319 +++
> 54 files changed, 6472 insertions(+), 105 deletions(-)
> create mode 100644 board/davedenx/qong/fpga.c
> create mode 100644 board/isee/igep0020/Makefile
> create mode 100644 board/isee/igep0020/config.mk
> create mode 100644 board/isee/igep0020/igep0020.c
> create mode 100644 board/isee/igep0020/igep0020.h
> create mode 100644 board/isee/igep0030/Makefile
> create mode 100644 board/isee/igep0030/config.mk
> create mode 100644 board/isee/igep0030/igep0030.c
> create mode 100644 board/isee/igep0030/igep0030.h
> create mode 100755 drivers/fpga/ivm_core.c
> create mode 100644 drivers/fpga/lattice.c
> create mode 100644 drivers/mmc/omap_hsmmc.c
> create mode 100644 drivers/usb/host/ehci-mxc.c
> create mode 100644 include/configs/igep0020.h
> create mode 100644 include/configs/igep0030.h
> create mode 100755 include/lattice.h
Applied, thanks.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Computers are not intelligent. They only think they are.
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request: u-boot-arm
@ 2010-10-13 18:40 Wolfgang Denk
2010-10-13 19:00 ` Wolfgang Denk
0 siblings, 1 reply; 40+ messages in thread
From: Wolfgang Denk @ 2010-10-13 18:40 UTC (permalink / raw)
To: u-boot
The following changes since commit bfc7bea6adc46e1db2f5a5e3464d7652ed67c864:
Merge branch 'master' of git://git.denx.de/u-boot-x86 (2010-10-11 10:00:34 +0200)
are available in the git repository at:
git://git.denx.de/u-boot-arm.git master
Albert Aribaud (6):
arm: bugfix: replace ble with blo in start.S files
orion5x: fix relocation-incompatible code
mvsata_ide: adjust port init sequence
orion5x: optimize window size computation
mvsata_ide: adjust port init sequence
orion5x: optimize window size computation
Alexander Stein (1):
at91: Add arch_preboot_os which disables PIT in a faster way
Andreas Bie?mann (6):
at91_emac.c: fix 'Warning: eth device name has a space!'
at91_emac.c: poll for IDLE when writing PHY
at91_emac.h: fix typo in register definition
atmel_usart: change register access to C structure
arch/arm/include/asm/sizes.h: cleanups
board/armltd/integrator/split_by_variant.sh: fix 'echo -n'
Ben Gardiner (1):
ARM: relocation: don't undef CONFIG_SYS_ARM_WITHOUT_RELOC
Heiko Schocher (1):
ARM: relocation: fix typo in comment
Matt Waddel (2):
ARMV7: Versatile Express Coretile CortexA9x4 support
ARMV7: Fixed baudrate setting in pl01x driver
Prafulla Wadaskar (8):
Kirkwood: print_cpuinfo fixed for valid devid revid
Kirkwood: dram_init is moved to dram.c
kirkwood: added common config file mv-common.h
Kirkwood: Changes specific to ARM relocation support
Kirkwood: print_cpuinfo fixed for valid devid revid
Kirkwood: dram_init is moved to dram.c
kirkwood: added common config file mv-common.h
Kirkwood: Changes specific to ARM relocation support
Reinhard Meyer (1):
AT91: convert cpu.c to struct SoC access
Stefano Babic (10):
Use common function to set GPIOs for MX3 and MX5
ARM: Use syslib functions for all CORTEXA8
MX51: Added pins definition to set up pads
MX51: add structure to access System Reset Controller
MXC: Add watchdog support to serial driver
MX51: Drop unused header file for mx51evk
MXC: Correct SPI_CPOL setting in SPI driver
MXC: Fix byte-ordering in SPI driver for i.MX31/i.MX51
MX51: Register definitions cannot be included in board config file
MX51: Support for TTECH vision2 board
Wolfgang Denk (3):
Merge branch 'master' of git://git.denx.de/u-boot-imx
Merge branch 'at91' of git://git.denx.de/u-boot-atmel
Merge branch 'master' of git://git.denx.de/u-boot-marvell
MAINTAINERS | 5 +
MAKEALL | 1 +
arch/arm/cpu/arm1136/start.S | 8 +-
arch/arm/cpu/arm1176/start.S | 10 +-
arch/arm/cpu/arm720t/start.S | 10 +-
arch/arm/cpu/arm920t/start.S | 10 +-
arch/arm/cpu/arm925t/start.S | 10 +-
arch/arm/cpu/arm926ejs/at91/cpu.c | 48 +-
arch/arm/cpu/arm926ejs/kirkwood/cpu.c | 34 +-
arch/arm/cpu/arm926ejs/kirkwood/dram.c | 38 +
arch/arm/cpu/arm926ejs/orion5x/cpu.c | 112 ++--
arch/arm/cpu/arm926ejs/orion5x/timer.c | 6 +-
arch/arm/cpu/arm926ejs/start.S | 10 +-
arch/arm/cpu/arm946es/start.S | 8 +-
arch/arm/cpu/arm_intcm/start.S | 10 +-
arch/arm/cpu/armv7/Makefile | 3 +-
arch/arm/cpu/armv7/omap-common/Makefile | 1 -
arch/arm/cpu/armv7/start.S | 8 +-
arch/arm/cpu/armv7/{omap-common => }/syslib.c | 0
arch/arm/cpu/ixp/start.S | 10 +-
arch/arm/cpu/lh7a40x/start.S | 11 +-
arch/arm/cpu/pxa/start.S | 8 +-
arch/arm/cpu/s3c44b0/start.S | 12 +-
arch/arm/cpu/sa1100/start.S | 10 +-
arch/arm/include/asm/arch-arm925t/sizes.h | 50 --
arch/arm/include/asm/arch-arm926ejs/sizes.h | 51 --
arch/arm/include/asm/arch-armv7/sysctrl.h | 70 ++
.../arm/include/asm/arch-armv7/systimer.h | 54 +-
.../arm/include/asm/arch-armv7/wdt.h | 57 +-
arch/arm/include/asm/arch-at91/at91_emac.h | 2 +-
arch/arm/include/asm/arch-kirkwood/cpu.h | 2 +
arch/arm/include/asm/arch-mx31/mx31-regs.h | 14 +-
arch/arm/include/asm/arch-mx31/mx31.h | 25 -
arch/arm/include/asm/arch-mx51/imx-regs.h | 26 +-
arch/arm/include/asm/arch-mx51/mx51_pins.h | 44 ++
arch/arm/include/asm/arch-mx51/sys_proto.h | 1 +
arch/arm/include/asm/arch-omap/sizes.h | 52 --
arch/arm/include/asm/arch-omap24xx/omap2420.h | 2 +-
arch/arm/include/asm/arch-omap24xx/sizes.h | 49 --
arch/arm/include/asm/arch-orion5x/cpu.h | 1 +
arch/arm/include/asm/sizes.h | 5 +-
board/Marvell/guruplug/guruplug.c | 11 -
board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c | 11 -
board/Marvell/openrd_base/openrd_base.c | 11 -
board/Marvell/rd6281a/rd6281a.c | 11 -
board/Marvell/sheevaplug/sheevaplug.c | 11 -
board/armltd/integrator/split_by_variant.sh | 129 ++--
board/armltd/vexpress/Makefile | 49 ++
board/armltd/vexpress/ca9x4_ct_vxp.c | 220 ++++++
board/armltd/vexpress/config.mk | 23 +
board/armltd/vexpress/u-boot.lds | 65 ++
board/davedenx/qong/qong.c | 29 +-
board/freescale/mx51evk/mx51evk.c | 2 -
board/ttcontrol/vision2/Makefile | 48 ++
board/ttcontrol/vision2/config.mk | 25 +
board/ttcontrol/vision2/imximage_hynix.cfg | 209 ++++++
board/ttcontrol/vision2/vision2.c | 711 ++++++++++++++++++++
boards.cfg | 2 +
drivers/block/mvsata_ide.c | 42 +-
drivers/gpio/Makefile | 2 +-
drivers/gpio/{mx31_gpio.c => mxc_gpio.c} | 47 +-
drivers/misc/fsl_pmic.c | 10 +-
drivers/net/at91_emac.c | 22 +-
drivers/serial/atmel_usart.c | 36 +-
drivers/serial/atmel_usart.h | 56 +-
drivers/serial/serial_mxc.c | 7 +-
drivers/serial/serial_pl01x.c | 93 +--
drivers/spi/mxc_spi.c | 168 ++++--
include/configs/ca9x4_ct_vxp.h | 196 ++++++
include/configs/da850evm.h | 1 -
include/configs/guruplug.h | 103 +---
include/configs/h2_p2_dbg_board.h | 2 +-
include/configs/imx27lite-common.h | 3 +-
include/configs/imx31_litekit.h | 4 +-
include/configs/imx31_phycore.h | 2 +-
include/configs/keymile-common.h | 1 +
include/configs/km_arm.h | 2 +-
include/configs/mv-common.h | 230 +++++++
include/configs/mv88f6281gtw_ge.h | 120 +---
include/configs/mx31ads.h | 4 +-
include/configs/mx31pdk.h | 4 +-
include/configs/mx51evk.h | 2 +-
include/configs/omap1510.h | 2 +-
include/configs/omap3_beagle.h | 3 +-
include/configs/omap730.h | 2 +-
include/configs/openrd_base.h | 146 +----
include/configs/qong.h | 9 +-
include/configs/rd6281a.h | 101 +---
include/configs/sheevaplug.h | 104 +---
include/configs/tx25.h | 3 +-
include/configs/vision2.h | 214 ++++++
include/mc13892.h | 3 +
.../mx51evk/mx51evk.h => include/mxc_gpio.h | 50 +-
93 files changed, 2904 insertions(+), 1345 deletions(-)
rename arch/arm/cpu/armv7/{omap-common => }/syslib.c (100%)
delete mode 100644 arch/arm/include/asm/arch-arm925t/sizes.h
delete mode 100644 arch/arm/include/asm/arch-arm926ejs/sizes.h
create mode 100644 arch/arm/include/asm/arch-armv7/sysctrl.h
copy board/freescale/mx51evk/mx51evk.h => arch/arm/include/asm/arch-armv7/systimer.h (55%)
copy board/freescale/mx51evk/mx51evk.h => arch/arm/include/asm/arch-armv7/wdt.h (55%)
delete mode 100644 arch/arm/include/asm/arch-omap/sizes.h
delete mode 100644 arch/arm/include/asm/arch-omap24xx/sizes.h
create mode 100644 board/armltd/vexpress/Makefile
create mode 100644 board/armltd/vexpress/ca9x4_ct_vxp.c
create mode 100644 board/armltd/vexpress/config.mk
create mode 100644 board/armltd/vexpress/u-boot.lds
create mode 100644 board/ttcontrol/vision2/Makefile
create mode 100644 board/ttcontrol/vision2/config.mk
create mode 100644 board/ttcontrol/vision2/imximage_hynix.cfg
create mode 100644 board/ttcontrol/vision2/vision2.c
rename drivers/gpio/{mx31_gpio.c => mxc_gpio.c} (63%)
create mode 100644 include/configs/ca9x4_ct_vxp.h
create mode 100644 include/configs/mv-common.h
create mode 100644 include/configs/vision2.h
rename board/freescale/mx51evk/mx51evk.h => include/mxc_gpio.h (54%)
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Making files is easy under the UNIX operating system. Therefore,
users tend to create numerous files using large amounts of file
space. It has been said that the only standard thing about all UNIX
systems is the message-of-the-day telling users to clean up their
files. - System V.2 administrator's guide
^ permalink raw reply [flat|nested] 40+ messages in thread* [U-Boot] Pull request: u-boot-arm
2010-10-13 18:40 Wolfgang Denk
@ 2010-10-13 19:00 ` Wolfgang Denk
0 siblings, 0 replies; 40+ messages in thread
From: Wolfgang Denk @ 2010-10-13 19:00 UTC (permalink / raw)
To: u-boot
In message <20101013184030.B935C1365CC@gemini.denx.de> you wrote:
> The following changes since commit bfc7bea6adc46e1db2f5a5e3464d7652ed67c864:
>
> Merge branch 'master' of git://git.denx.de/u-boot-x86 (2010-10-11 10:00:34 +0200)
>
> are available in the git repository at:
>
> git://git.denx.de/u-boot-arm.git master
>
> Albert Aribaud (6):
> arm: bugfix: replace ble with blo in start.S files
> orion5x: fix relocation-incompatible code
> mvsata_ide: adjust port init sequence
> orion5x: optimize window size computation
> mvsata_ide: adjust port init sequence
> orion5x: optimize window size computation
>
> Alexander Stein (1):
> at91: Add arch_preboot_os which disables PIT in a faster way
>
> Andreas Bie?mann (6):
> at91_emac.c: fix 'Warning: eth device name has a space!'
> at91_emac.c: poll for IDLE when writing PHY
> at91_emac.h: fix typo in register definition
> atmel_usart: change register access to C structure
> arch/arm/include/asm/sizes.h: cleanups
> board/armltd/integrator/split_by_variant.sh: fix 'echo -n'
>
> Ben Gardiner (1):
> ARM: relocation: don't undef CONFIG_SYS_ARM_WITHOUT_RELOC
>
> Heiko Schocher (1):
> ARM: relocation: fix typo in comment
>
> Matt Waddel (2):
> ARMV7: Versatile Express Coretile CortexA9x4 support
> ARMV7: Fixed baudrate setting in pl01x driver
>
> Prafulla Wadaskar (8):
> Kirkwood: print_cpuinfo fixed for valid devid revid
> Kirkwood: dram_init is moved to dram.c
> kirkwood: added common config file mv-common.h
> Kirkwood: Changes specific to ARM relocation support
> Kirkwood: print_cpuinfo fixed for valid devid revid
> Kirkwood: dram_init is moved to dram.c
> kirkwood: added common config file mv-common.h
> Kirkwood: Changes specific to ARM relocation support
>
> Reinhard Meyer (1):
> AT91: convert cpu.c to struct SoC access
>
> Stefano Babic (10):
> Use common function to set GPIOs for MX3 and MX5
> ARM: Use syslib functions for all CORTEXA8
> MX51: Added pins definition to set up pads
> MX51: add structure to access System Reset Controller
> MXC: Add watchdog support to serial driver
> MX51: Drop unused header file for mx51evk
> MXC: Correct SPI_CPOL setting in SPI driver
> MXC: Fix byte-ordering in SPI driver for i.MX31/i.MX51
> MX51: Register definitions cannot be included in board config file
> MX51: Support for TTECH vision2 board
>
> Wolfgang Denk (3):
> Merge branch 'master' of git://git.denx.de/u-boot-imx
> Merge branch 'at91' of git://git.denx.de/u-boot-atmel
> Merge branch 'master' of git://git.denx.de/u-boot-marvell
>
> MAINTAINERS | 5 +
> MAKEALL | 1 +
> arch/arm/cpu/arm1136/start.S | 8 +-
> arch/arm/cpu/arm1176/start.S | 10 +-
> arch/arm/cpu/arm720t/start.S | 10 +-
> arch/arm/cpu/arm920t/start.S | 10 +-
> arch/arm/cpu/arm925t/start.S | 10 +-
> arch/arm/cpu/arm926ejs/at91/cpu.c | 48 +-
> arch/arm/cpu/arm926ejs/kirkwood/cpu.c | 34 +-
> arch/arm/cpu/arm926ejs/kirkwood/dram.c | 38 +
> arch/arm/cpu/arm926ejs/orion5x/cpu.c | 112 ++--
> arch/arm/cpu/arm926ejs/orion5x/timer.c | 6 +-
> arch/arm/cpu/arm926ejs/start.S | 10 +-
> arch/arm/cpu/arm946es/start.S | 8 +-
> arch/arm/cpu/arm_intcm/start.S | 10 +-
> arch/arm/cpu/armv7/Makefile | 3 +-
> arch/arm/cpu/armv7/omap-common/Makefile | 1 -
> arch/arm/cpu/armv7/start.S | 8 +-
> arch/arm/cpu/armv7/{omap-common => }/syslib.c | 0
> arch/arm/cpu/ixp/start.S | 10 +-
> arch/arm/cpu/lh7a40x/start.S | 11 +-
> arch/arm/cpu/pxa/start.S | 8 +-
> arch/arm/cpu/s3c44b0/start.S | 12 +-
> arch/arm/cpu/sa1100/start.S | 10 +-
> arch/arm/include/asm/arch-arm925t/sizes.h | 50 --
> arch/arm/include/asm/arch-arm926ejs/sizes.h | 51 --
> arch/arm/include/asm/arch-armv7/sysctrl.h | 70 ++
> .../arm/include/asm/arch-armv7/systimer.h | 54 +-
> .../arm/include/asm/arch-armv7/wdt.h | 57 +-
> arch/arm/include/asm/arch-at91/at91_emac.h | 2 +-
> arch/arm/include/asm/arch-kirkwood/cpu.h | 2 +
> arch/arm/include/asm/arch-mx31/mx31-regs.h | 14 +-
> arch/arm/include/asm/arch-mx31/mx31.h | 25 -
> arch/arm/include/asm/arch-mx51/imx-regs.h | 26 +-
> arch/arm/include/asm/arch-mx51/mx51_pins.h | 44 ++
> arch/arm/include/asm/arch-mx51/sys_proto.h | 1 +
> arch/arm/include/asm/arch-omap/sizes.h | 52 --
> arch/arm/include/asm/arch-omap24xx/omap2420.h | 2 +-
> arch/arm/include/asm/arch-omap24xx/sizes.h | 49 --
> arch/arm/include/asm/arch-orion5x/cpu.h | 1 +
> arch/arm/include/asm/sizes.h | 5 +-
> board/Marvell/guruplug/guruplug.c | 11 -
> board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c | 11 -
> board/Marvell/openrd_base/openrd_base.c | 11 -
> board/Marvell/rd6281a/rd6281a.c | 11 -
> board/Marvell/sheevaplug/sheevaplug.c | 11 -
> board/armltd/integrator/split_by_variant.sh | 129 ++--
> board/armltd/vexpress/Makefile | 49 ++
> board/armltd/vexpress/ca9x4_ct_vxp.c | 220 ++++++
> board/armltd/vexpress/config.mk | 23 +
> board/armltd/vexpress/u-boot.lds | 65 ++
> board/davedenx/qong/qong.c | 29 +-
> board/freescale/mx51evk/mx51evk.c | 2 -
> board/ttcontrol/vision2/Makefile | 48 ++
> board/ttcontrol/vision2/config.mk | 25 +
> board/ttcontrol/vision2/imximage_hynix.cfg | 209 ++++++
> board/ttcontrol/vision2/vision2.c | 711 ++++++++++++++++> ++++
> boards.cfg | 2 +
> drivers/block/mvsata_ide.c | 42 +-
> drivers/gpio/Makefile | 2 +-
> drivers/gpio/{mx31_gpio.c => mxc_gpio.c} | 47 +-
> drivers/misc/fsl_pmic.c | 10 +-
> drivers/net/at91_emac.c | 22 +-
> drivers/serial/atmel_usart.c | 36 +-
> drivers/serial/atmel_usart.h | 56 +-
> drivers/serial/serial_mxc.c | 7 +-
> drivers/serial/serial_pl01x.c | 93 +--
> drivers/spi/mxc_spi.c | 168 ++++--
> include/configs/ca9x4_ct_vxp.h | 196 ++++++
> include/configs/da850evm.h | 1 -
> include/configs/guruplug.h | 103 +---
> include/configs/h2_p2_dbg_board.h | 2 +-
> include/configs/imx27lite-common.h | 3 +-
> include/configs/imx31_litekit.h | 4 +-
> include/configs/imx31_phycore.h | 2 +-
> include/configs/keymile-common.h | 1 +
> include/configs/km_arm.h | 2 +-
> include/configs/mv-common.h | 230 +++++++
> include/configs/mv88f6281gtw_ge.h | 120 +---
> include/configs/mx31ads.h | 4 +-
> include/configs/mx31pdk.h | 4 +-
> include/configs/mx51evk.h | 2 +-
> include/configs/omap1510.h | 2 +-
> include/configs/omap3_beagle.h | 3 +-
> include/configs/omap730.h | 2 +-
> include/configs/openrd_base.h | 146 +----
> include/configs/qong.h | 9 +-
> include/configs/rd6281a.h | 101 +---
> include/configs/sheevaplug.h | 104 +---
> include/configs/tx25.h | 3 +-
> include/configs/vision2.h | 214 ++++++
> include/mc13892.h | 3 +
> .../mx51evk/mx51evk.h => include/mxc_gpio.h | 50 +-
> 93 files changed, 2904 insertions(+), 1345 deletions(-)
> rename arch/arm/cpu/armv7/{omap-common => }/syslib.c (100%)
> delete mode 100644 arch/arm/include/asm/arch-arm925t/sizes.h
> delete mode 100644 arch/arm/include/asm/arch-arm926ejs/sizes.h
> create mode 100644 arch/arm/include/asm/arch-armv7/sysctrl.h
> copy board/freescale/mx51evk/mx51evk.h => arch/arm/include/asm/arch-armv> 7/systimer.h (55%)
> copy board/freescale/mx51evk/mx51evk.h => arch/arm/include/asm/arch-armv> 7/wdt.h (55%)
> delete mode 100644 arch/arm/include/asm/arch-omap/sizes.h
> delete mode 100644 arch/arm/include/asm/arch-omap24xx/sizes.h
> create mode 100644 board/armltd/vexpress/Makefile
> create mode 100644 board/armltd/vexpress/ca9x4_ct_vxp.c
> create mode 100644 board/armltd/vexpress/config.mk
> create mode 100644 board/armltd/vexpress/u-boot.lds
> create mode 100644 board/ttcontrol/vision2/Makefile
> create mode 100644 board/ttcontrol/vision2/config.mk
> create mode 100644 board/ttcontrol/vision2/imximage_hynix.cfg
> create mode 100644 board/ttcontrol/vision2/vision2.c
> rename drivers/gpio/{mx31_gpio.c => mxc_gpio.c} (63%)
> create mode 100644 include/configs/ca9x4_ct_vxp.h
> create mode 100644 include/configs/mv-common.h
> create mode 100644 include/configs/vision2.h
> rename board/freescale/mx51evk/mx51evk.h => include/mxc_gpio.h (54%)
Applied.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Stupidity, like virtue, is its own reward.
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request u-boot-arm
@ 2010-08-10 21:03 Wolfgang Denk
0 siblings, 0 replies; 40+ messages in thread
From: Wolfgang Denk @ 2010-08-10 21:03 UTC (permalink / raw)
To: u-boot
> The following changes since commit 201532a69cf7e7a84bff354fdab45947425d22b4:
>
> Merge branch 'master' of ../master (2010-08-10 22:20:27 +0200)
>
> are available in the git repository at:
>
> git://git.denx.de/u-boot-arm.git master
>
> Albert Aribaud (6):
> ide: add configuration
> ide: reorder object files alphabetically
> ide: add mvsata_ide driver
> cmd_ide: add support for orion5x
> edminiv2: add mvsata_ide and cmd_ide support
> orion5x: allow overriding default mappings windows
>
> Li Haibo (1):
> MX51EVK: fix return value of get_timer_masked
>
> Prafulla Wadaskar (2):
> cmd_ide: add support for Kirkwood
> Kirkwood: openrd_base: Added SATA support
>
> Reinhard Meyer (1):
> fix cmd_mmc.c, line 136 missing "
>
> Steve Sakoman (8):
> ARMV7: Add pad mux support for OMAP4
> ARMV7: Fix udelay for OMAP4
> ARMV7: Modify i2c driver for more reliable operation on OMAP4
> ARMV7: Add support for the TWL6030 I2C power chip used in OMAP4 systems
> ARMV7: Restructure omap3 musb driver to allow code sharing between OMAP3 and OMAP4
> ARMV7: Enable musb driver and usbtty on OMAP4430 SDP
> ARMV7: Enable musb driver and usbtty on OMAP4 Panda
> ARMV7: Update default environment for OMAP4 boards
>
> arch/arm/cpu/arm926ejs/orion5x/cpu.c | 40 ++--
> arch/arm/cpu/armv7/mx51/timer.c | 2 +-
> arch/arm/cpu/armv7/omap-common/timer.c | 9 -
> arch/arm/cpu/armv7/omap4/board.c | 11 +
> arch/arm/include/asm/arch-kirkwood/kirkwood.h | 5 +
> arch/arm/include/asm/arch-omap3/cpu.h | 3 +
> arch/arm/include/asm/arch-omap3/i2c.h | 4 +-
> arch/arm/include/asm/arch-omap4/cpu.h | 3 +
> arch/arm/include/asm/arch-omap4/mux_omap4.h | 344 +++++++++++++++++++++++++
> arch/arm/include/asm/arch-omap4/omap4.h | 2 +
> arch/arm/include/asm/arch-omap4/sys_proto.h | 1 +
> arch/arm/include/asm/arch-orion5x/cpu.h | 98 ++++++--
> arch/arm/include/asm/arch-orion5x/orion5x.h | 3 +
> arch/powerpc/include/asm/config.h | 3 +
> board/ti/panda/panda.c | 26 ++
> board/ti/panda/panda.h | 265 +++++++++++++++++++
> board/ti/sdp4430/sdp.c | 26 ++
> board/ti/sdp4430/sdp.h | 265 +++++++++++++++++++
> common/cmd_ide.c | 25 ++-
> common/cmd_mmc.c | 2 +-
> doc/README.PXA_CF | 8 +
> drivers/block/Makefile | 7 +-
> drivers/block/mvsata_ide.c | 140 ++++++++++
> drivers/i2c/omap24xx_i2c.c | 31 ++-
> drivers/i2c/omap24xx_i2c.h | 4 +
> drivers/power/Makefile | 1 +
> drivers/power/twl6030.c | 78 ++++++
> drivers/usb/musb/omap3.c | 16 ++
> drivers/usb/musb/omap3.h | 3 +-
> include/configs/ap325rxa.h | 1 +
> include/configs/edminiv2.h | 34 +++-
> include/configs/ms7720se.h | 1 +
> include/configs/omap4_panda.h | 26 ++-
> include/configs/omap4_sdp4430.h | 26 ++-
> include/configs/openrd_base.h | 31 +++
> include/configs/r2dplus.h | 1 +
> include/configs/r7780mp.h | 1 +
> include/twl6030.h | 91 +++++++
> 38 files changed, 1556 insertions(+), 81 deletions(-)
> create mode 100644 arch/arm/include/asm/arch-omap4/mux_omap4.h
> create mode 100644 board/ti/panda/panda.h
> create mode 100644 board/ti/sdp4430/sdp.h
> create mode 100644 drivers/block/mvsata_ide.c
> create mode 100644 drivers/power/twl6030.c
> create mode 100644 include/twl6030.h
Applied, thanks.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"Confound these ancestors.... They've stolen our best ideas!"
- Ben Jonson
^ permalink raw reply [flat|nested] 40+ messages in thread
* [U-Boot] Pull request u-boot-arm
@ 2010-08-10 20:51 Wolfgang Denk
0 siblings, 0 replies; 40+ messages in thread
From: Wolfgang Denk @ 2010-08-10 20:51 UTC (permalink / raw)
To: u-boot
The following changes since commit 201532a69cf7e7a84bff354fdab45947425d22b4:
Merge branch 'master' of ../master (2010-08-10 22:20:27 +0200)
are available in the git repository at:
git://git.denx.de/u-boot-arm.git master
Albert Aribaud (6):
ide: add configuration
ide: reorder object files alphabetically
ide: add mvsata_ide driver
cmd_ide: add support for orion5x
edminiv2: add mvsata_ide and cmd_ide support
orion5x: allow overriding default mappings windows
Li Haibo (1):
MX51EVK: fix return value of get_timer_masked
Prafulla Wadaskar (2):
cmd_ide: add support for Kirkwood
Kirkwood: openrd_base: Added SATA support
Reinhard Meyer (1):
fix cmd_mmc.c, line 136 missing "
Steve Sakoman (8):
ARMV7: Add pad mux support for OMAP4
ARMV7: Fix udelay for OMAP4
ARMV7: Modify i2c driver for more reliable operation on OMAP4
ARMV7: Add support for the TWL6030 I2C power chip used in OMAP4 systems
ARMV7: Restructure omap3 musb driver to allow code sharing between OMAP3 and OMAP4
ARMV7: Enable musb driver and usbtty on OMAP4430 SDP
ARMV7: Enable musb driver and usbtty on OMAP4 Panda
ARMV7: Update default environment for OMAP4 boards
arch/arm/cpu/arm926ejs/orion5x/cpu.c | 40 ++--
arch/arm/cpu/armv7/mx51/timer.c | 2 +-
arch/arm/cpu/armv7/omap-common/timer.c | 9 -
arch/arm/cpu/armv7/omap4/board.c | 11 +
arch/arm/include/asm/arch-kirkwood/kirkwood.h | 5 +
arch/arm/include/asm/arch-omap3/cpu.h | 3 +
arch/arm/include/asm/arch-omap3/i2c.h | 4 +-
arch/arm/include/asm/arch-omap4/cpu.h | 3 +
arch/arm/include/asm/arch-omap4/mux_omap4.h | 344 +++++++++++++++++++++++++
arch/arm/include/asm/arch-omap4/omap4.h | 2 +
arch/arm/include/asm/arch-omap4/sys_proto.h | 1 +
arch/arm/include/asm/arch-orion5x/cpu.h | 98 ++++++--
arch/arm/include/asm/arch-orion5x/orion5x.h | 3 +
arch/powerpc/include/asm/config.h | 3 +
board/ti/panda/panda.c | 26 ++
board/ti/panda/panda.h | 265 +++++++++++++++++++
board/ti/sdp4430/sdp.c | 26 ++
board/ti/sdp4430/sdp.h | 265 +++++++++++++++++++
common/cmd_ide.c | 25 ++-
common/cmd_mmc.c | 2 +-
doc/README.PXA_CF | 8 +
drivers/block/Makefile | 7 +-
drivers/block/mvsata_ide.c | 140 ++++++++++
drivers/i2c/omap24xx_i2c.c | 31 ++-
drivers/i2c/omap24xx_i2c.h | 4 +
drivers/power/Makefile | 1 +
drivers/power/twl6030.c | 78 ++++++
drivers/usb/musb/omap3.c | 16 ++
drivers/usb/musb/omap3.h | 3 +-
include/configs/ap325rxa.h | 1 +
include/configs/edminiv2.h | 34 +++-
include/configs/ms7720se.h | 1 +
include/configs/omap4_panda.h | 26 ++-
include/configs/omap4_sdp4430.h | 26 ++-
include/configs/openrd_base.h | 31 +++
include/configs/r2dplus.h | 1 +
include/configs/r7780mp.h | 1 +
include/twl6030.h | 91 +++++++
38 files changed, 1556 insertions(+), 81 deletions(-)
create mode 100644 arch/arm/include/asm/arch-omap4/mux_omap4.h
create mode 100644 board/ti/panda/panda.h
create mode 100644 board/ti/sdp4430/sdp.h
create mode 100644 drivers/block/mvsata_ide.c
create mode 100644 drivers/power/twl6030.c
create mode 100644 include/twl6030.h
^ permalink raw reply [flat|nested] 40+ messages in thread
end of thread, other threads:[~2011-05-23 7:06 UTC | newest]
Thread overview: 40+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-02-17 20:49 [U-Boot] Pull request: u-boot-arm Albert ARIBAUD
2011-02-18 6:24 ` [U-Boot] PLEASE HOLD - " Albert ARIBAUD
-- strict thread matches above, loose matches on Subject: below --
2011-05-23 7:06 [U-Boot] " Albert ARIBAUD
2011-05-18 12:20 Albert ARIBAUD
2011-05-18 12:42 ` Wolfgang Denk
2011-02-21 7:33 Albert ARIBAUD
2011-02-21 22:16 ` Wolfgang Denk
2011-02-02 0:09 Albert ARIBAUD
2011-02-02 20:57 ` Wolfgang Denk
2010-11-26 20:29 Wolfgang Denk
2010-11-26 20:55 ` Wolfgang Denk
2010-11-27 7:43 ` Dirk Behme
2010-11-27 9:06 ` Albert ARIBAUD
2010-11-27 17:19 ` Paulraj, Sandeep
2010-11-27 19:36 ` Wolfgang Denk
2010-11-27 18:50 ` Wolfgang Denk
2010-11-27 19:42 ` Albert ARIBAUD
2010-11-27 20:50 ` Wolfgang Denk
2010-11-27 21:15 ` Albert ARIBAUD
2010-11-27 22:09 ` Albert ARIBAUD
2010-11-27 22:27 ` Albert ARIBAUD
2010-11-28 7:40 ` Dirk Behme
2010-11-28 5:15 ` Thomas Weber
2010-11-27 23:33 ` Steve Sakoman
2010-11-27 23:57 ` Paulraj, Sandeep
2010-11-28 3:15 ` Steve Sakoman
2010-11-29 20:16 ` Dirk Behme
2010-11-29 20:27 ` Paulraj, Sandeep
2010-11-17 19:50 Wolfgang Denk
2010-11-17 19:55 ` Wolfgang Denk
2010-11-17 21:34 ` Loïc Minier
2010-11-17 21:54 ` Wolfgang Denk
2010-10-19 22:08 Wolfgang Denk
2010-10-19 22:14 ` Wolfgang Denk
2010-10-17 18:24 Wolfgang Denk
2010-10-17 18:36 ` Wolfgang Denk
2010-10-13 18:40 Wolfgang Denk
2010-10-13 19:00 ` Wolfgang Denk
2010-08-10 21:03 [U-Boot] Pull request u-boot-arm Wolfgang Denk
2010-08-10 20:51 Wolfgang Denk
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox