[U-Boot] [PATCH v2 5/5] I2C: add i2c support for Armada100 platform

[Heiko Schocher <heiko.schocher@invitel.hu>]

Hello Lei,

Lei Wen wrote:
> Signed-off-by: Lei Wen <leiwen@marvell.com>
> ---
>  arch/arm/cpu/arm926ejs/armada100/cpu.c    |   14 ++++++++++++++
>  arch/arm/include/asm/arch-armada100/mfp.h |    4 ++++
>  board/Marvell/aspenite/aspenite.c         |    5 +++++
>  include/configs/aspenite.h                |   12 ++++++++++++
>  4 files changed, 35 insertions(+), 0 deletions(-)
> 
> diff --git a/arch/arm/cpu/arm926ejs/armada100/cpu.c b/arch/arm/cpu/arm926ejs/armada100/cpu.c
> index 62aa175..8039ad2 100644
> --- a/arch/arm/cpu/arm926ejs/armada100/cpu.c
> +++ b/arch/arm/cpu/arm926ejs/armada100/cpu.c
> @@ -62,6 +62,14 @@ int arch_cpu_init(void)
>  	/* Enable GPIO clock */
>  	writel(APBC_APBCLK, &apb1clkres->gpio);
>  
> +	/* Enable general I2C clock */
> +	writel(APBC_RST | APBC_FNCLK | APBC_APBCLK, &apb1clkres->twsi0);
> +	writel(APBC_FNCLK | APBC_APBCLK, &apb1clkres->twsi0);
> +
> +	/* Enable power I2C clock */
> +	writel(APBC_RST | APBC_FNCLK | APBC_APBCLK, &apb1clkres->twsi1);
> +	writel(APBC_FNCLK | APBC_APBCLK, &apb1clkres->twsi1);
> +

If boards based on this cpu type don;t use i2c, i2c clock and
power would be enabled ... wouldn;t it be better, if we enable
this only if CONFIG_I2C_MV is defined?

Hmm.. are the comments OK? In the first "block" you only
use twsi0 register, in the second "block" only twsi1 ...?

>  	/*
>  	 * Enable Functional and APB clock at 14.7456MHz
>  	 * for configured UART console
> @@ -90,3 +98,9 @@ int print_cpuinfo(void)
>  	return 0;
>  }
>  #endif
> +
> +#ifdef CONFIG_I2C_MV
> +void i2c_clk_enable (void)
> +{
> +}
> +#endif
> diff --git a/arch/arm/include/asm/arch-armada100/mfp.h b/arch/arm/include/asm/arch-armada100/mfp.h
> index d21a79f..f22b5e7 100644
> --- a/arch/arm/include/asm/arch-armada100/mfp.h
> +++ b/arch/arm/include/asm/arch-armada100/mfp.h
> @@ -60,6 +60,10 @@
>  #define MFPO8_UART3_RXD		MFP_REG(0x06c) | MFP_AF2 | MFP_DRIVE_MEDIUM
>  #define MFPO9_UART3_TXD		MFP_REG(0x070) | MFP_AF2 | MFP_DRIVE_MEDIUM
>  
> +/* I2c */
> +#define MFP105_CI2C_SDA		MFP_REG(0x1a4) | MFP_AF1 | MFP_DRIVE_MEDIUM
> +#define MFP106_CI2C_SCL		MFP_REG(0x1a8) | MFP_AF1 | MFP_DRIVE_MEDIUM
> +

Please add braces around this multiple or concatenation

>  /* More macros can be defined here... */
>  
>  #define MFP_PIN_MAX	117
> diff --git a/board/Marvell/aspenite/aspenite.c b/board/Marvell/aspenite/aspenite.c
> index 046ffd6..34ac7aa 100644
> --- a/board/Marvell/aspenite/aspenite.c
> +++ b/board/Marvell/aspenite/aspenite.c
> @@ -33,9 +33,14 @@ DECLARE_GLOBAL_DATA_PTR;
>  int board_early_init_f(void)
>  {
>  	u32 mfp_cfg[] = {
> +		/* I2C */
> +		MFP105_CI2C_SDA,
> +		MFP106_CI2C_SCL,
> +
>  		/* Enable Console on UART1 */
>  		MFP107_UART1_RXD,
>  		MFP108_UART1_TXD,
> +
>  		MFP_EOC		/*End of configureation*/
>  	};
>  	/* configure MFP's */
> diff --git a/include/configs/aspenite.h b/include/configs/aspenite.h
> index fd35f3e..50f8ed7 100644
> --- a/include/configs/aspenite.h
> +++ b/include/configs/aspenite.h
> @@ -63,6 +63,18 @@
>  #undef CONFIG_ARCH_MISC_INIT
>  
>  /*
> + * I2C definition
> + */
> +#define CONFIG_CMD_I2C		1
> +#define CONFIG_I2C_MV		1
> +#define CONFIG_PXA_I2C_NUM	2
> +#define CONFIG_I2C_MULTI_BUS	1
> +#define CONFIG_PXA_I2C_REG	{0xd4011000, 0xd4025000}
> +#define CONFIG_HARD_I2C		1
> +#define CONFIG_SYS_I2C_SPEED	0
> +#define CONFIG_SYS_I2C_SLAVE	0xfe
> +
> +/*
>   * Environment variables configurations
>   */
>  #define CONFIG_ENV_IS_NOWHERE	1	/* if env in SDRAM */

Thanks!

bye,
Heiko