From: Albert ARIBAUD <albert.u.boot@aribaud.net>
To: u-boot@lists.denx.de
Subject: [U-Boot] Please pull u-boot-ti/master Update
Date: Sun, 04 Sep 2011 07:49:17 +0200 [thread overview]
Message-ID: <4E63115D.10907@aribaud.net> (raw)
In-Reply-To: <1315109686-2625-1-git-send-email-s-paulraj@ti.com>
Le 04/09/2011 06:14, s-paulraj at ti.com a ?crit :
> Albert,
>
> Please pull u-boot-ti/master.
> I was unable to apply a couple of patches.
> I have asked the developers to send updated patches for those.
> In the meanwhile can you please accept this pull request.
> This set should apply clean on top of u-boot-arm.
>
> Regards,
> Sandeep
>
> The following changes since commit d91dd34bf113e8e23d52e8a5267858ddb07de88c:
> Marek Vasut (1):
> PXA: vpac270: Remove re-defined CONFIG_SYS_TEXT_BASE
>
> are available in the git repository at:
>
> git://git.denx.de/u-boot-ti.git master
>
> Bob Feretich (1):
> OMAP3 Beagle Pin Mux initialization glitch fix
>
> Christian Spielberger (1):
> beagleboard: enable HUB power on all variants of the BeagleBoard
>
> Eric Benard (1):
> dm3730: enable dpll5
>
> Jason Kridner (12):
> USB: Remove __attribute__ ((packed)) for struct ehci_hccr and ehci_hcor
> BeagleBoard: Added userbutton command
> BeagleBoard: Configure DVI/S-video
> BeagleBoard: config: make mtest run
> BeagleBoard: config: increase command-line functionality
> BeagleBoard: config: add optargs/buddy/camera
> BeagleBoard: config: Enabled multibus support for I2C in configuration
> BeagleBoard: config: updated default configuration
> Corrected LED name match finding avoiding extraneous Usage printouts
> BeagleBoard: fix LED 0/1 in driver
> led: added cmd_led to Makefile
> led: correct off/on locations in structure
>
> Joel A Fernandes (4):
> BeagleBoard: config: hardcode MAC for onboard SMSC
> BeagleBoard: config: use uImage.beagle for tftp
> led: Fixed setting of STATUS_LED_BIT1 when led_name is 'all'
> led: Remove state-saving of led for toggle functionality and add toggle option to led command
>
> Joel Fernandes (1):
> ehci-hcd: Allow cleanups to happen gracefully on a timeout.
>
> Koen Kooi (8):
> beagle: pass expansionboard name in bootargs
> beagleboard: add support for xM revision C
> BeagleBoard: turn off clocks in ehci_stop
> BeagleBoard: config: load kernel from MMC ext, not FAT
> BeagleBoard: config: decrease bootdelay to 2 seconds
> BeagleBoard: config: enable networking
> BeagleBoard: config: enable asix driver and dhcp
> BeagleBoard: config: enable DSS
>
> Manjunathappa, Prakash (1):
> da850: add support for Spectrum Digital AM18xx EVM
>
> Nagabhushana Netagunte (8):
> dm6446: disable cache usage due to coherency issues
> dm365: disable cache usage due to coherency issues
> da850: indicate cache usage disable in config file
> da850: add NOR boot mode support
> da850: modify the U-Boot prompt string
> da850: add support to wake up DSP during board init
> da850: fix the channel number for EMAC teardown init
> da850: modifications for Logic PD Rev.3 AM18xx EVM
>
> Rajashekhara, Sudhakar (1):
> dm365: modify boot prompt from dm365 to dm36x
>
> Steve Sakoman (1):
> OMAP: Remove omapfb.debug=y from Beagle and Overo env settings
>
> Sudhakar Rajashekhara (1):
> da8xx: add support for multiple PLL controllers
>
> Syed Mohammed Khasim (1):
> OMAP3: Add DSS driver for OMAP3
>
> Tom Rini (9):
> OMAP3: CM-T35: Use generic MMC driver
> OMAP3: DIG297: Use generic MMC driver
> OMAP3: Zoom1: Use generic MMC driver
> OMAP3: Zoom2: Use generic MMC driver
> OMAP3: pandora: Use generic MMC driver
> AM3517 CraneBoard: Use generic MMC driver
> TI OMAP3 SDP3430: Use generic MMC driver
> devkit8000: Use generic MMC driver
> OMAP3: Remove legacy mmc driver
>
> Vaibhav Hiremath (5):
> OMAP3/4: Increase console I/O buffer size
> omap3:clock: configure GFX clock to 200MHz for AM/DM37x
> omap3:clock: check cpu_family before enabling clks for IVA& CAM
> omap3evm: Use generic MMC driver
> am3517evm: Use generic MMC driver
>
> arch/arm/cpu/arm926ejs/davinci/cpu.c | 30 +-
> arch/arm/cpu/armv7/omap3/clock.c | 17 +-
> arch/arm/include/asm/arch-davinci/hardware.h | 14 +-
> arch/arm/include/asm/arch-omap3/clocks_omap3.h | 1 +
> arch/arm/include/asm/arch-omap3/dss.h | 174 +++++++
> board/cm_t35/cm_t35.c | 8 +
> board/comelit/dig297/dig297.c | 9 +
> board/davinci/da8xxevm/da850evm.c | 123 +++++
> board/logicpd/am3517evm/am3517evm.c | 9 +
> board/logicpd/zoom1/zoom1.c | 9 +
> board/logicpd/zoom2/zoom2.c | 9 +
> board/pandora/pandora.c | 9 +
> board/ti/am3517crane/am3517crane.c | 9 +
> board/ti/beagle/beagle.c | 118 +++++-
> board/ti/beagle/beagle.h | 87 ++++
> board/ti/beagle/led.c | 32 +-
> board/ti/evm/evm.c | 9 +
> board/ti/sdp3430/sdp.c | 9 +
> board/timll/devkit8000/devkit8000.c | 9 +
> common/Makefile | 1 +
> common/cmd_led.c | 73 ++--
> drivers/mmc/Makefile | 1 -
> drivers/mmc/omap3_mmc.c | 570 ------------------------
> drivers/mmc/omap3_mmc.h | 233 ----------
> drivers/net/davinci_emac.c | 4 +-
> drivers/usb/host/ehci-hcd.c | 1 -
> drivers/usb/host/ehci.h | 4 +-
> drivers/video/Makefile | 2 +
> drivers/video/omap3_dss.c | 131 ++++++
> include/configs/am3517_crane.h | 10 +-
> include/configs/am3517_evm.h | 10 +-
> include/configs/cm_t35.h | 3 +-
> include/configs/da850evm.h | 26 +-
> include/configs/davinci_dm365evm.h | 5 +-
> include/configs/davinci_dvevm.h | 3 +
> include/configs/devkit8000.h | 10 +-
> include/configs/dig297.h | 5 +-
> include/configs/omap3_beagle.h | 77 +++-
> include/configs/omap3_evm.h | 12 +-
> include/configs/omap3_overo.h | 4 +-
> include/configs/omap3_pandora.h | 7 +-
> include/configs/omap3_sdp3430.h | 5 +-
> include/configs/omap3_zoom1.h | 12 +-
> include/configs/omap3_zoom2.h | 5 +-
> include/configs/omap4_panda.h | 2 +-
> include/configs/omap4_sdp4430.h | 2 +-
> 46 files changed, 970 insertions(+), 933 deletions(-)
> create mode 100644 arch/arm/include/asm/arch-omap3/dss.h
> delete mode 100644 drivers/mmc/omap3_mmc.c
> delete mode 100644 drivers/mmc/omap3_mmc.h
> create mode 100644 drivers/video/omap3_dss.c
Applied to u-boot-arm/master, thanks.
Amicalement,
--
Albert.
prev parent reply other threads:[~2011-09-04 5:49 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-09-04 4:14 [U-Boot] Please pull u-boot-ti/master Update s-paulraj at ti.com
2011-09-04 5:49 ` Albert ARIBAUD [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4E63115D.10907@aribaud.net \
--to=albert.u.boot@aribaud.net \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox