* [U-Boot] [PATCH] net: Add \n before warning message so it prints on a new line.
@ 2011-09-07 11:57 Philip Balister
2011-09-07 11:57 ` [U-Boot] [PATCH] OMAP3: Overo: Update GPMC timing for ethernet chip Philip Balister
` (2 more replies)
0 siblings, 3 replies; 10+ messages in thread
From: Philip Balister @ 2011-09-07 11:57 UTC (permalink / raw)
To: u-boot
Signed-off-by: Philip Balister <philip@opensdr.com>
---
net/eth.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
diff --git a/net/eth.c b/net/eth.c
index dbd1e2d..67a8039 100644
--- a/net/eth.c
+++ b/net/eth.c
@@ -305,7 +305,7 @@ int eth_initialize(bd_t *bis)
puts("\nWarning: eth device name has a space!\n");
if (eth_write_hwaddr(dev, "eth", eth_number))
- puts("Warning: failed to set MAC address\n");
+ puts("\nWarning: failed to set MAC address\n");
eth_number++;
dev = dev->next;
--
1.7.4.4
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH] OMAP3: Overo: Update GPMC timing for ethernet chip.
2011-09-07 11:57 [U-Boot] [PATCH] net: Add \n before warning message so it prints on a new line Philip Balister
@ 2011-09-07 11:57 ` Philip Balister
2011-09-08 14:21 ` Steve Sakoman
2011-09-07 11:57 ` [U-Boot] [PATCH] overo: Set IEN on GPMC_CLK to support CS's that use synchronous clocking Philip Balister
2011-09-08 15:01 ` [U-Boot] [PATCH] net: Add \n before warning message so it prints on a new line Albert ARIBAUD
2 siblings, 1 reply; 10+ messages in thread
From: Philip Balister @ 2011-09-07 11:57 UTC (permalink / raw)
To: u-boot
The existing timing does not quite meet the minimum requirements
in the LAN9221 datasheet. The timing in this patch solves problems
noticed on some parts.
Signed-off-by: Philip Balister <philip@opensdr.com>
---
board/overo/overo.h | 6 +++---
1 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/board/overo/overo.h b/board/overo/overo.h
index 68e1243..617c0c3 100644
--- a/board/overo/overo.h
+++ b/board/overo/overo.h
@@ -35,10 +35,10 @@ const omap3_sysinfo sysinfo = {
/* GPMC CS 5 connected to an SMSC LAN9221 ethernet controller */
#define NET_LAN9221_GPMC_CONFIG1 0x00001000
-#define NET_LAN9221_GPMC_CONFIG2 0x00080701
+#define NET_LAN9221_GPMC_CONFIG2 0x00060700
#define NET_LAN9221_GPMC_CONFIG3 0x00020201
-#define NET_LAN9221_GPMC_CONFIG4 0x08030703
-#define NET_LAN9221_GPMC_CONFIG5 0x00060908
+#define NET_LAN9221_GPMC_CONFIG4 0x06000700
+#define NET_LAN9221_GPMC_CONFIG5 0x0006090A
#define NET_LAN9221_GPMC_CONFIG6 0x87030000
#define NET_LAN9221_GPMC_CONFIG7 0x00000f6c
--
1.7.4.4
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH] overo: Set IEN on GPMC_CLK to support CS's that use synchronous clocking.
2011-09-07 11:57 [U-Boot] [PATCH] net: Add \n before warning message so it prints on a new line Philip Balister
2011-09-07 11:57 ` [U-Boot] [PATCH] OMAP3: Overo: Update GPMC timing for ethernet chip Philip Balister
@ 2011-09-07 11:57 ` Philip Balister
2011-09-08 15:01 ` [U-Boot] [PATCH] net: Add \n before warning message so it prints on a new line Albert ARIBAUD
2 siblings, 0 replies; 10+ messages in thread
From: Philip Balister @ 2011-09-07 11:57 UTC (permalink / raw)
To: u-boot
Without this change CS's configured for synchronous clocking cannot
read data.
Signed-off-by: Philip Balister <philip@opensdr.com>
---
board/overo/overo.h | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
diff --git a/board/overo/overo.h b/board/overo/overo.h
index 68e1243..1f94669 100644
--- a/board/overo/overo.h
+++ b/board/overo/overo.h
@@ -128,7 +128,7 @@ const omap3_sysinfo sysinfo = {
MUX_VAL(CP(GPMC_NCS6), (IEN | PTD | DIS | M0)) /*GPMC_nCS6*/\
MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | EN | M0)) /*GPMC_nCS7*/\
MUX_VAL(CP(GPMC_NBE1), (IEN | PTD | DIS | M0)) /*GPMC_nCS3*/\
- MUX_VAL(CP(GPMC_CLK), (IDIS | PTU | EN | M0)) /*GPMC_CLK*/\
+ MUX_VAL(CP(GPMC_CLK), (IEN | PTU | EN | M0)) /*GPMC_CLK*/\
MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) /*GPMC_nADV_ALE*/\
MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) /*GPMC_nOE*/\
MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) /*GPMC_nWE*/\
--
1.7.4.4
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH] OMAP3: Overo: Update GPMC timing for ethernet chip.
2011-09-07 11:57 ` [U-Boot] [PATCH] OMAP3: Overo: Update GPMC timing for ethernet chip Philip Balister
@ 2011-09-08 14:21 ` Steve Sakoman
2011-09-08 14:45 ` Enric Balletbò i Serra
0 siblings, 1 reply; 10+ messages in thread
From: Steve Sakoman @ 2011-09-08 14:21 UTC (permalink / raw)
To: u-boot
On Wed, Sep 7, 2011 at 4:57 AM, Philip Balister <philip@balister.org> wrote:
> The existing timing does not quite meet the minimum requirements
> in the LAN9221 datasheet. The timing in this patch solves problems
> noticed on some parts.
>
> Signed-off-by: Philip Balister <philip@opensdr.com>
Acked-by: Steve Sakoman <steve@sakoman.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
> ---
> ?board/overo/overo.h | ? ?6 +++---
> ?1 files changed, 3 insertions(+), 3 deletions(-)
>
> diff --git a/board/overo/overo.h b/board/overo/overo.h
> index 68e1243..617c0c3 100644
> --- a/board/overo/overo.h
> +++ b/board/overo/overo.h
> @@ -35,10 +35,10 @@ const omap3_sysinfo sysinfo = {
>
> ?/* GPMC CS 5 connected to an SMSC LAN9221 ethernet controller */
> ?#define NET_LAN9221_GPMC_CONFIG1 ? ?0x00001000
> -#define NET_LAN9221_GPMC_CONFIG2 ? ?0x00080701
> +#define NET_LAN9221_GPMC_CONFIG2 ? ?0x00060700
> ?#define NET_LAN9221_GPMC_CONFIG3 ? ?0x00020201
> -#define NET_LAN9221_GPMC_CONFIG4 ? ?0x08030703
> -#define NET_LAN9221_GPMC_CONFIG5 ? ?0x00060908
> +#define NET_LAN9221_GPMC_CONFIG4 ? ?0x06000700
> +#define NET_LAN9221_GPMC_CONFIG5 ? ?0x0006090A
> ?#define NET_LAN9221_GPMC_CONFIG6 ? ?0x87030000
> ?#define NET_LAN9221_GPMC_CONFIG7 ? ?0x00000f6c
>
> --
> 1.7.4.4
>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
>
^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH] OMAP3: Overo: Update GPMC timing for ethernet chip.
2011-09-08 14:21 ` Steve Sakoman
@ 2011-09-08 14:45 ` Enric Balletbò i Serra
2011-09-08 18:50 ` Philip Balister
0 siblings, 1 reply; 10+ messages in thread
From: Enric Balletbò i Serra @ 2011-09-08 14:45 UTC (permalink / raw)
To: u-boot
2011/9/8 Steve Sakoman <sakoman@gmail.com>:
> On Wed, Sep 7, 2011 at 4:57 AM, Philip Balister <philip@balister.org> wrote:
>> The existing timing does not quite meet the minimum requirements
>> in the LAN9221 datasheet. The timing in this patch solves problems
>> noticed on some parts.
>>
>> Signed-off-by: Philip Balister <philip@opensdr.com>
>
> Acked-by: Steve Sakoman <steve@sakoman.com>
> Tested-by: Steve Sakoman <steve@sakoman.com>
>
>> ---
>> ?board/overo/overo.h | ? ?6 +++---
>> ?1 files changed, 3 insertions(+), 3 deletions(-)
>>
>> diff --git a/board/overo/overo.h b/board/overo/overo.h
>> index 68e1243..617c0c3 100644
>> --- a/board/overo/overo.h
>> +++ b/board/overo/overo.h
>> @@ -35,10 +35,10 @@ const omap3_sysinfo sysinfo = {
>>
>> ?/* GPMC CS 5 connected to an SMSC LAN9221 ethernet controller */
>> ?#define NET_LAN9221_GPMC_CONFIG1 ? ?0x00001000
>> -#define NET_LAN9221_GPMC_CONFIG2 ? ?0x00080701
>> +#define NET_LAN9221_GPMC_CONFIG2 ? ?0x00060700
>> ?#define NET_LAN9221_GPMC_CONFIG3 ? ?0x00020201
>> -#define NET_LAN9221_GPMC_CONFIG4 ? ?0x08030703
>> -#define NET_LAN9221_GPMC_CONFIG5 ? ?0x00060908
>> +#define NET_LAN9221_GPMC_CONFIG4 ? ?0x06000700
>> +#define NET_LAN9221_GPMC_CONFIG5 ? ?0x0006090A
>> ?#define NET_LAN9221_GPMC_CONFIG6 ? ?0x87030000
>> ?#define NET_LAN9221_GPMC_CONFIG7 ? ?0x00000f6c
>>
>> --
>> 1.7.4.4
>>
>> _______________________________________________
>> U-Boot mailing list
>> U-Boot at lists.denx.de
>> http://lists.denx.de/mailman/listinfo/u-boot
>>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
>
Other boards like IGEP v2 board uses the same LAN9221 ethernet
controller, so this code is duplicated on overo.h and igep0020.h
files. Maybe could be a good idea move this part to
arch/arm/include/asm/arch-omap3/omap_gpmc.h or another file to not
duplicate the code.
^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH] net: Add \n before warning message so it prints on a new line.
2011-09-07 11:57 [U-Boot] [PATCH] net: Add \n before warning message so it prints on a new line Philip Balister
2011-09-07 11:57 ` [U-Boot] [PATCH] OMAP3: Overo: Update GPMC timing for ethernet chip Philip Balister
2011-09-07 11:57 ` [U-Boot] [PATCH] overo: Set IEN on GPMC_CLK to support CS's that use synchronous clocking Philip Balister
@ 2011-09-08 15:01 ` Albert ARIBAUD
2011-09-08 15:04 ` Philip Balister
2 siblings, 1 reply; 10+ messages in thread
From: Albert ARIBAUD @ 2011-09-08 15:01 UTC (permalink / raw)
To: u-boot
Hi Philip,
Le 07/09/2011 13:57, Philip Balister a ?crit :
> Signed-off-by: Philip Balister<philip@opensdr.com>
> ---
> net/eth.c | 2 +-
> 1 files changed, 1 insertions(+), 1 deletions(-)
>
> diff --git a/net/eth.c b/net/eth.c
> index dbd1e2d..67a8039 100644
> --- a/net/eth.c
> +++ b/net/eth.c
> @@ -305,7 +305,7 @@ int eth_initialize(bd_t *bis)
> puts("\nWarning: eth device name has a space!\n");
>
> if (eth_write_hwaddr(dev, "eth", eth_number))
> - puts("Warning: failed to set MAC address\n");
> + puts("\nWarning: failed to set MAC address\n");
I believe warning messages with \n on more than one end are frowned upon.
> eth_number++;
> dev = dev->next;
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH] net: Add \n before warning message so it prints on a new line.
2011-09-08 15:01 ` [U-Boot] [PATCH] net: Add \n before warning message so it prints on a new line Albert ARIBAUD
@ 2011-09-08 15:04 ` Philip Balister
2011-09-08 16:08 ` Albert ARIBAUD
0 siblings, 1 reply; 10+ messages in thread
From: Philip Balister @ 2011-09-08 15:04 UTC (permalink / raw)
To: u-boot
On 09/08/2011 11:01 AM, Albert ARIBAUD wrote:
> Hi Philip,
>
> Le 07/09/2011 13:57, Philip Balister a ?crit :
>> Signed-off-by: Philip Balister<philip@opensdr.com>
>> ---
>> net/eth.c | 2 +-
>> 1 files changed, 1 insertions(+), 1 deletions(-)
>>
>> diff --git a/net/eth.c b/net/eth.c
>> index dbd1e2d..67a8039 100644
>> --- a/net/eth.c
>> +++ b/net/eth.c
>> @@ -305,7 +305,7 @@ int eth_initialize(bd_t *bis)
>> puts("\nWarning: eth device name has a space!\n");
>>
>> if (eth_write_hwaddr(dev, "eth", eth_number))
>> - puts("Warning: failed to set MAC address\n");
>> + puts("\nWarning: failed to set MAC address\n");
>
> I believe warning messages with \n on more than one end are frowned upon.
Look closely at the patch, the warning message above has to do the same
thing. Without the leading \n on the message, it prints directly after
the ethernet chip name, with no space. This is not right. I chose to
copy the existing code, rather than add a leading space.
Philip
>
>> eth_number++;
>> dev = dev->next;
>
> Amicalement,
^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH] net: Add \n before warning message so it prints on a new line.
2011-09-08 15:04 ` Philip Balister
@ 2011-09-08 16:08 ` Albert ARIBAUD
0 siblings, 0 replies; 10+ messages in thread
From: Albert ARIBAUD @ 2011-09-08 16:08 UTC (permalink / raw)
To: u-boot
Le 08/09/2011 17:04, Philip Balister a ?crit :
> On 09/08/2011 11:01 AM, Albert ARIBAUD wrote:
>> Hi Philip,
>>
>> Le 07/09/2011 13:57, Philip Balister a ?crit :
>>> Signed-off-by: Philip Balister<philip@opensdr.com>
>>> ---
>>> net/eth.c | 2 +-
>>> 1 files changed, 1 insertions(+), 1 deletions(-)
>>>
>>> diff --git a/net/eth.c b/net/eth.c
>>> index dbd1e2d..67a8039 100644
>>> --- a/net/eth.c
>>> +++ b/net/eth.c
>>> @@ -305,7 +305,7 @@ int eth_initialize(bd_t *bis)
>>> puts("\nWarning: eth device name has a space!\n");
>>>
>>> if (eth_write_hwaddr(dev, "eth", eth_number))
>>> - puts("Warning: failed to set MAC address\n");
>>> + puts("\nWarning: failed to set MAC address\n");
>>
>> I believe warning messages with \n on more than one end are frowned upon.
>
> Look closely at the patch, the warning message above has to do the same
> thing. Without the leading \n on the message, it prints directly after
> the ethernet chip name, with no space. This is not right. I chose to
> copy the existing code, rather than add a leading space.
Just because original code has an error does not make it right to
reproduce it. :)
More seriously, heterogeneous \n placement makes it complicated to get
and keep printing right -- for instance here the warning messages have a
trailing \n but the code loop adds one at the end.
I would prefer that the code do a first loop (while dev!= eth_devices)
to try and set up ethernet devices, emitting simple "warning\n" messages
as needed, then a second loop (for dev=0 to eth_number-1) to print a
summary of the final list of eth devices found and initialized.
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH] OMAP3: Overo: Update GPMC timing for ethernet chip.
2011-09-08 14:45 ` Enric Balletbò i Serra
@ 2011-09-08 18:50 ` Philip Balister
2011-09-08 19:48 ` Enric Balletbò i Serra
0 siblings, 1 reply; 10+ messages in thread
From: Philip Balister @ 2011-09-08 18:50 UTC (permalink / raw)
To: u-boot
On 09/08/2011 10:45 AM, Enric Balletb? i Serra wrote:
> 2011/9/8 Steve Sakoman<sakoman@gmail.com>:
>> On Wed, Sep 7, 2011 at 4:57 AM, Philip Balister<philip@balister.org> wrote:
>>> The existing timing does not quite meet the minimum requirements
>>> in the LAN9221 datasheet. The timing in this patch solves problems
>>> noticed on some parts.
>>>
>>> Signed-off-by: Philip Balister<philip@opensdr.com>
>>
>> Acked-by: Steve Sakoman<steve@sakoman.com>
>> Tested-by: Steve Sakoman<steve@sakoman.com>
>>
>>> ---
>>> board/overo/overo.h | 6 +++---
>>> 1 files changed, 3 insertions(+), 3 deletions(-)
>>>
>>> diff --git a/board/overo/overo.h b/board/overo/overo.h
>>> index 68e1243..617c0c3 100644
>>> --- a/board/overo/overo.h
>>> +++ b/board/overo/overo.h
>>> @@ -35,10 +35,10 @@ const omap3_sysinfo sysinfo = {
>>>
>>> /* GPMC CS 5 connected to an SMSC LAN9221 ethernet controller */
>>> #define NET_LAN9221_GPMC_CONFIG1 0x00001000
>>> -#define NET_LAN9221_GPMC_CONFIG2 0x00080701
>>> +#define NET_LAN9221_GPMC_CONFIG2 0x00060700
>>> #define NET_LAN9221_GPMC_CONFIG3 0x00020201
>>> -#define NET_LAN9221_GPMC_CONFIG4 0x08030703
>>> -#define NET_LAN9221_GPMC_CONFIG5 0x00060908
>>> +#define NET_LAN9221_GPMC_CONFIG4 0x06000700
>>> +#define NET_LAN9221_GPMC_CONFIG5 0x0006090A
>>> #define NET_LAN9221_GPMC_CONFIG6 0x87030000
>>> #define NET_LAN9221_GPMC_CONFIG7 0x00000f6c
>>>
>>> --
>>> 1.7.4.4
>>>
>>> _______________________________________________
>>> U-Boot mailing list
>>> U-Boot at lists.denx.de
>>> http://lists.denx.de/mailman/listinfo/u-boot
>>>
>> _______________________________________________
>> U-Boot mailing list
>> U-Boot at lists.denx.de
>> http://lists.denx.de/mailman/listinfo/u-boot
>>
>
> Other boards like IGEP v2 board uses the same LAN9221 ethernet
> controller, so this code is duplicated on overo.h and igep0020.h
> files. Maybe could be a good idea move this part to
> arch/arm/include/asm/arch-omap3/omap_gpmc.h or another file to not
> duplicate the code.
Is there anyone around with an igep v2 board who could test/ack such a
patch?
Philip
^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH] OMAP3: Overo: Update GPMC timing for ethernet chip.
2011-09-08 18:50 ` Philip Balister
@ 2011-09-08 19:48 ` Enric Balletbò i Serra
0 siblings, 0 replies; 10+ messages in thread
From: Enric Balletbò i Serra @ 2011-09-08 19:48 UTC (permalink / raw)
To: u-boot
2011/9/8 Philip Balister <philip@opensdr.com>:
> On 09/08/2011 10:45 AM, Enric Balletb? i Serra wrote:
>>
>> 2011/9/8 Steve Sakoman<sakoman@gmail.com>:
>>>
>>> On Wed, Sep 7, 2011 at 4:57 AM, Philip Balister<philip@balister.org>
>>> ?wrote:
>>>>
>>>> The existing timing does not quite meet the minimum requirements
>>>> in the LAN9221 datasheet. The timing in this patch solves problems
>>>> noticed on some parts.
>>>>
>>>> Signed-off-by: Philip Balister<philip@opensdr.com>
>>>
>>> Acked-by: Steve Sakoman<steve@sakoman.com>
>>> Tested-by: Steve Sakoman<steve@sakoman.com>
>>>
>>>> ---
>>>> ?board/overo/overo.h | ? ?6 +++---
>>>> ?1 files changed, 3 insertions(+), 3 deletions(-)
>>>>
>>>> diff --git a/board/overo/overo.h b/board/overo/overo.h
>>>> index 68e1243..617c0c3 100644
>>>> --- a/board/overo/overo.h
>>>> +++ b/board/overo/overo.h
>>>> @@ -35,10 +35,10 @@ const omap3_sysinfo sysinfo = {
>>>>
>>>> ?/* GPMC CS 5 connected to an SMSC LAN9221 ethernet controller */
>>>> ?#define NET_LAN9221_GPMC_CONFIG1 ? ?0x00001000
>>>> -#define NET_LAN9221_GPMC_CONFIG2 ? ?0x00080701
>>>> +#define NET_LAN9221_GPMC_CONFIG2 ? ?0x00060700
>>>> ?#define NET_LAN9221_GPMC_CONFIG3 ? ?0x00020201
>>>> -#define NET_LAN9221_GPMC_CONFIG4 ? ?0x08030703
>>>> -#define NET_LAN9221_GPMC_CONFIG5 ? ?0x00060908
>>>> +#define NET_LAN9221_GPMC_CONFIG4 ? ?0x06000700
>>>> +#define NET_LAN9221_GPMC_CONFIG5 ? ?0x0006090A
>>>> ?#define NET_LAN9221_GPMC_CONFIG6 ? ?0x87030000
>>>> ?#define NET_LAN9221_GPMC_CONFIG7 ? ?0x00000f6c
>>>>
>>>> --
>>>> 1.7.4.4
>>>>
>>>> _______________________________________________
>>>> U-Boot mailing list
>>>> U-Boot at lists.denx.de
>>>> http://lists.denx.de/mailman/listinfo/u-boot
>>>>
>>> _______________________________________________
>>> U-Boot mailing list
>>> U-Boot at lists.denx.de
>>> http://lists.denx.de/mailman/listinfo/u-boot
>>>
>>
>> Other boards like IGEP v2 board uses the same LAN9221 ethernet
>> controller, so this code is duplicated on overo.h and igep0020.h
>> files. Maybe could be a good idea move this part to
>> arch/arm/include/asm/arch-omap3/omap_gpmc.h or another file to not
>> duplicate the code.
>
> Is there anyone around with an igep v2 board who could test/ack such a
> patch?
>
> Philip
>
Yes, I can, I expect test the patch tomorrow ...
Enric
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2011-09-08 19:48 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-09-07 11:57 [U-Boot] [PATCH] net: Add \n before warning message so it prints on a new line Philip Balister
2011-09-07 11:57 ` [U-Boot] [PATCH] OMAP3: Overo: Update GPMC timing for ethernet chip Philip Balister
2011-09-08 14:21 ` Steve Sakoman
2011-09-08 14:45 ` Enric Balletbò i Serra
2011-09-08 18:50 ` Philip Balister
2011-09-08 19:48 ` Enric Balletbò i Serra
2011-09-07 11:57 ` [U-Boot] [PATCH] overo: Set IEN on GPMC_CLK to support CS's that use synchronous clocking Philip Balister
2011-09-08 15:01 ` [U-Boot] [PATCH] net: Add \n before warning message so it prints on a new line Albert ARIBAUD
2011-09-08 15:04 ` Philip Balister
2011-09-08 16:08 ` Albert ARIBAUD
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox