From: Igor Grinberg <grinberg@compulab.co.il>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 02/31] iMX28: Add basic support for DENX M28EVK board
Date: Fri, 09 Sep 2011 10:13:14 +0300 [thread overview]
Message-ID: <4E69BC8A.501@compulab.co.il> (raw)
In-Reply-To: <1315514579-19215-3-git-send-email-marek.vasut@gmail.com>
On 09/08/2011 11:42 PM, Marek Vasut wrote:
> This contains support for booting the board and output via DUART.
>
> Signed-off-by: Marek Vasut<marek.vasut@gmail.com>
> Cc: Stefano Babic<sbabic@denx.de>
> Cc: Wolfgang Denk<wd@denx.de>
> Cc: Detlev Zundel<dzu@denx.de>
> ---
[...]
> diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
> new file mode 100644
> index 0000000..5f4f787
> --- /dev/null
> +++ b/board/denx/m28evk/m28evk.c
[...]
> +
> +int board_init(void)
> +{
> + /* Will change it for MX28 EVK later */
> + gd->bd->bi_arch_number = CONFIG_M28_MACHID;
This should be done in the board config file.
Please, see the CONFIG_MACH_TYPE in the U-Boot documentation (README file).
> + /* Adress of boot parameters */
> + gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
> +
> + return 0;
> +}
[...]
--
Regards,
Igor.
next prev parent reply other threads:[~2011-09-09 7:13 UTC|newest]
Thread overview: 68+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-09-08 20:42 [U-Boot] [PATCH 00/31] Support for the DENX M28 SoM Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 01/31] iMX28: Initial support for iMX28 CPU Marek Vasut
2011-09-09 8:23 ` Stefano Babic
2011-09-09 8:54 ` Heiko Schocher
2011-09-09 10:12 ` Marek Vasut
2011-09-09 10:29 ` Stefano Babic
2011-09-09 10:50 ` Marek Vasut
2011-09-09 11:04 ` Stefano Babic
2011-09-08 20:42 ` [U-Boot] [PATCH 02/31] iMX28: Add basic support for DENX M28EVK board Marek Vasut
2011-09-09 7:13 ` Igor Grinberg [this message]
2011-09-09 8:26 ` Stefano Babic
2011-09-08 20:42 ` [U-Boot] [PATCH 03/31] iMX28: Add support for SSP MMC Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 04/31] M28EVK: Enable MMC support Marek Vasut
2011-09-09 8:28 ` Stefano Babic
2011-09-08 20:42 ` [U-Boot] [PATCH 05/31] iMX28: Add pinctrl and ocotp register definitions Marek Vasut
2011-09-09 8:30 ` Stefano Babic
2011-09-08 20:42 ` [U-Boot] [PATCH 06/31] FEC: Add support for iMX28 quirks Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 07/31] iMX28: Add CPU-specific FEC ethernet init Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 08/31] M28EVK: Enable FEC0 and FEC1 Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 09/31] iMX28: Add PINMUX control Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 10/31] iMX28: Add RTC register definitions Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 11/31] iMX28: Add I2C " Marek Vasut
2011-09-09 5:44 ` Heiko Schocher
2011-09-08 20:42 ` [U-Boot] [PATCH 12/31] iMX28: Add I2C bus driver Marek Vasut
2011-09-09 5:45 ` Heiko Schocher
2011-09-09 11:18 ` Marek Vasut
2011-09-09 11:26 ` Stefan Roese
2011-09-09 11:52 ` Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 13/31] M28: Enable I2C, EEPROM and RTC Marek Vasut
2011-09-09 5:45 ` Heiko Schocher
2011-09-08 20:42 ` [U-Boot] [PATCH 14/31] iMX28: Add MMC SPL Marek Vasut
2011-09-09 5:44 ` Chander Kashyap
2011-09-09 7:33 ` Wolfgang Denk
[not found] ` <CANuQgHH_p-_HRf_jBKiPZz=br0+aCyWROWzHDZgV47xWg97aiQ@mail.gmail.com>
2011-09-09 12:49 ` Marek Vasut
2011-09-09 13:14 ` Chander Kashyap
2011-09-10 20:58 ` Marek Vasut
2011-09-10 21:04 ` Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 15/31] M28: Enable " Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 16/31] iMX28: Add GPIO control Marek Vasut
2011-09-09 8:46 ` Stefano Babic
2011-09-08 20:42 ` [U-Boot] [PATCH 17/31] M28: Enable use of GPIO configurators Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 18/31] iMX28: Add SPI driver Marek Vasut
2011-09-09 8:51 ` Stefano Babic
2011-09-09 11:50 ` Marek Vasut
2011-09-09 12:34 ` Stefano Babic
2011-09-09 12:50 ` Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 19/31] M28EVK: Enable SPI and SPI flash Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 20/31] iMX28: Add APBH DMA driver Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 21/31] iMX28: Add BCH and GPMI register definitions Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 22/31] iMX28: Add GPMI NAND driver Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 23/31] M28: Enable NAND Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 24/31] iMX28: Add driver for internal RTC Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 25/31] M28: Enable the internal RTC instead of the M41T62 Marek Vasut
2011-09-09 12:45 ` Stefano Babic
2011-09-09 12:51 ` Marek Vasut
2011-09-09 12:55 ` Stefano Babic
2011-09-08 20:42 ` [U-Boot] [PATCH 26/31] M28: Enable UBI and UBIFS Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 27/31] M28: Save environment in NAND Marek Vasut
2011-09-16 19:15 ` Scott Wood
2011-09-17 8:20 ` Marek Vasut
2011-09-19 17:54 ` Scott Wood
2011-09-17 7:10 ` Fabio Estevam
2011-09-08 20:42 ` [U-Boot] [PATCH 28/31] iMX28: Add image header generator tool Marek Vasut
2011-09-09 8:58 ` Stefano Babic
2011-09-09 11:51 ` Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 29/31] M28: Add NAND update scripts Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 30/31] i.MX28: Add u-boot.sb target to Makefile Marek Vasut
2011-09-08 20:42 ` [U-Boot] [PATCH 31/31] M28: Add doc/README.m28 documentation Marek Vasut
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4E69BC8A.501@compulab.co.il \
--to=grinberg@compulab.co.il \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox