[U-Boot] [PATCH v3] zmx25: Fix build warning due to 'get_reset_cause' defined but not used

[Stefano Babic <sbabic@denx.de>]

On 09/23/2011 05:13 PM, Fabio Estevam wrote:
> When building the zmx25 target we get:
> 
> Configuring for zmx25 board...
> generic.c:108: warning: 'get_reset_cause' defined but not used
> 
> Fix this warning by defining get_reset_cause only if CONFIG_DISPLAY_CPUINFO is defined.
> 
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> ---
> Changes since v2:
> - Move the location of get_reset_cause
> Changes since v1:
> - Only define get_reset_cause when CONFIG_DISPLAY_CPUINFO is defined.
>  arch/arm/cpu/arm926ejs/mx25/generic.c |   46 ++++++++++++++++----------------
>  1 files changed, 23 insertions(+), 23 deletions(-)
> 
> diff --git a/arch/arm/cpu/arm926ejs/mx25/generic.c b/arch/arm/cpu/arm926ejs/mx25/generic.c
> index 1261640..8e60a26 100644
> --- a/arch/arm/cpu/arm926ejs/mx25/generic.c
> +++ b/arch/arm/cpu/arm926ejs/mx25/generic.c
> @@ -105,29 +105,6 @@ ulong imx_get_perclk (int clk)
>  	return lldiv (fref, div);
>  }
>  
> -static char *get_reset_cause(void)
> -{
> -	/* read RCSR register from CCM module */
> -	struct ccm_regs *ccm =
> -		(struct ccm_regs *)IMX_CCM_BASE;
> -
> -	u32 cause = readl(&ccm->rcsr) & 0x0f;
> -
> -	if (cause == 0)
> -		return "POR";
> -	else if (cause == 1)
> -		return "RST";
> -	else if ((cause & 2) == 2)
> -		return "WDOG";
> -	else if ((cause & 4) == 4)
> -		return "SW RESET";
> -	else if ((cause & 8) == 8)
> -		return "JTAG";
> -	else
> -		return "unknown reset";
> -
> -}
> -
>  u32 get_cpu_rev(void)
>  {
>  	u32 srev;
> @@ -153,6 +130,29 @@ u32 get_cpu_rev(void)
>  }
>  
>  #if defined(CONFIG_DISPLAY_CPUINFO)
> +static char *get_reset_cause(void)
> +{
> +	/* read RCSR register from CCM module */
> +	struct ccm_regs *ccm =
> +		(struct ccm_regs *)IMX_CCM_BASE;
> +
> +	u32 cause = readl(&ccm->rcsr) & 0x0f;
> +
> +	if (cause == 0)
> +		return "POR";
> +	else if (cause == 1)
> +		return "RST";
> +	else if ((cause & 2) == 2)
> +		return "WDOG";
> +	else if ((cause & 4) == 4)
> +		return "SW RESET";
> +	else if ((cause & 8) == 8)
> +		return "JTAG";
> +	else
> +		return "unknown reset";
> +
> +}
> +
>  int print_cpuinfo (void)
>  {
>  	char buf[32];

Acked-by: Stefano Babic <sbabic@denx.de>

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================