[U-Boot] [PATCH 1/2] fdt: Add new fdt_set_node_status & fdt_set_status_by_alias helpers

[U-Boot] [PATCH 1/2] fdt: Add new fdt_set_node_status & fdt_set_status_by_alias helpers

[Kumar Gala]

From: Shengzhou Liu <Shengzhou.Liu@freescale.com>

Add common function fdt_set_node_status() to assist in various locations
that we set a nodes status.  This function utilizes the status values
that are part of the EPAPR spec (on power.org).

fdt_set_status_by_alias() is based on fdt_set_node_status() but uses an
alias string to identify the node to update.

We also add some shortcut functions to help the common cases of setting
"okay" and "disabled":

	fdt_status_okay()
	fdt_status_disabled()
	fdt_status_okay_by_alias()
	fdt_status_disabled_by_alias()

Finally, we fixup the corenet_ds ethernet code which previously had
a function by the same name that can be replaced with the new helpers.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 board/freescale/corenet_ds/eth_hydra.c |   26 ++------------
 board/freescale/corenet_ds/eth_p4080.c |   36 +++++--------------
 common/fdt_support.c                   |   60 +++++++++++++++++++++++++++++++-
 include/fdt_support.h                  |   28 +++++++++++++++
 4 files changed, 101 insertions(+), 49 deletions(-)

diff --git a/board/freescale/corenet_ds/eth_hydra.c b/board/freescale/corenet_ds/eth_hydra.c
index 91b3408..a7a5e13 100644
--- a/board/freescale/corenet_ds/eth_hydra.c
+++ b/board/freescale/corenet_ds/eth_hydra.c
@@ -70,6 +70,7 @@
 #include <fm_eth.h>
 #include <fsl_mdio.h>
 #include <malloc.h>
+#include <fdt_support.h>
 #include <asm/fsl_dtsec.h>
 
 #include "../common/ngpixis.h"
@@ -200,25 +201,6 @@ static int hydra_mdio_init(char *realbusname, char *fakebusname)
 }
 
 /*
- * Given an alias or a path for a node, set the status of that node.
- *
- * If 'alias' is not a valid alias, then it is treated as a full path to the
- * node.  No error checking is performed.
- *
- * This function is normally called to set the status for a virtual MDIO node.
- */
-static void fdt_set_node_status(void *fdt, const char *alias,
-				const char *status)
-{
-	const char *path = fdt_get_alias(fdt, alias);
-
-	if (!path)
-		path = alias;
-
-	do_fixup_by_path(fdt, path, "status", status, strlen(status) + 1, 1);
-}
-
-/*
  * Given an alias or a path for a node, set the mux value of that node.
  *
  * If 'alias' is not a valid alias, then it is treated as a full path to the
@@ -372,14 +354,14 @@ void fdt_fixup_board_enet(void *fdt)
 		case PHY_INTERFACE_MODE_SGMII:
 			lane = serdes_get_first_lane(SGMII_FM1_DTSEC1 + idx);
 			if (lane >= 0) {
-				fdt_set_node_status(fdt, "emi1_sgmii", "okay");
+				fdt_status_okay_by_alias(fdt, "emi1_sgmii");
 				/* Also set the MUX value */
 				fdt_set_mdio_mux(fdt, "emi1_sgmii",
 						 mdio_mux[i].val);
 			}
 			break;
 		case PHY_INTERFACE_MODE_RGMII:
-			fdt_set_node_status(fdt, "emi1_rgmii", "okay");
+			fdt_status_okay_by_alias(fdt, "emi1_rgmii");
 			break;
 		default:
 			break;
@@ -388,7 +370,7 @@ void fdt_fixup_board_enet(void *fdt)
 
 	lane = serdes_get_first_lane(XAUI_FM1);
 	if (lane >= 0)
-		fdt_set_node_status(fdt, "emi2_xgmii", "okay");
+		fdt_status_okay_by_alias(fdt, "emi2_xgmii");
 #endif
 }
 
diff --git a/board/freescale/corenet_ds/eth_p4080.c b/board/freescale/corenet_ds/eth_p4080.c
index d4657f7..00dfa9a 100644
--- a/board/freescale/corenet_ds/eth_p4080.c
+++ b/board/freescale/corenet_ds/eth_p4080.c
@@ -199,22 +199,6 @@ static int p4080ds_mdio_init(char *realbusname, u32 muxval)
 	return mdio_register(bus);
 }
 
-/*
- * Sets the specified node's status to the value contained in "status"
- * If the first character of the specified path is "/" then we use
- * alias as a path.  Otherwise, we look for an alias of that name
- */
-static void fdt_set_node_status(void *fdt, const char *alias,
-			const char *status)
-{
-	const char *path = fdt_get_alias(fdt, alias);
-
-	if (!path)
-		path = alias;
-
-	do_fixup_by_path(fdt, path, "status", status, strlen(status) + 1, 1);
-}
-
 void board_ft_fman_fixup_port(void *blob, char * prop, phys_addr_t pa,
 				enum fm_port port, int offset)
 {
@@ -255,28 +239,28 @@ void fdt_fixup_board_enet(void *fdt)
 	 */
 
 	/* We've got six MDIO nodes that may or may not need to exist */
-	fdt_set_node_status(fdt, "emi1_slot3", "disabled");
-	fdt_set_node_status(fdt, "emi1_slot4", "disabled");
-	fdt_set_node_status(fdt, "emi1_slot5", "disabled");
-	fdt_set_node_status(fdt, "emi2_slot4", "disabled");
-	fdt_set_node_status(fdt, "emi2_slot5", "disabled");
+	fdt_status_disabled_by_alias(fdt, "emi1_slot3");
+	fdt_status_disabled_by_alias(fdt, "emi1_slot4");
+	fdt_status_disabled_by_alias(fdt, "emi1_slot5");
+	fdt_status_disabled_by_alias(fdt, "emi2_slot4");
+	fdt_status_disabled_by_alias(fdt, "emi2_slot5");
 
 	for (i = 0; i < NUM_FM_PORTS; i++) {
 		switch (mdio_mux[i]) {
 		case EMI1_SLOT3:
-			fdt_set_node_status(fdt, "emi1_slot3", "okay");
+			fdt_status_okay_by_alias(fdt, "emi1_slot3");
 			break;
 		case EMI1_SLOT4:
-			fdt_set_node_status(fdt, "emi1_slot4", "okay");
+			fdt_status_okay_by_alias(fdt, "emi1_slot4");
 			break;
 		case EMI1_SLOT5:
-			fdt_set_node_status(fdt, "emi1_slot5", "okay");
+			fdt_status_okay_by_alias(fdt, "emi1_slot5");
 			break;
 		case EMI2_SLOT4:
-			fdt_set_node_status(fdt, "emi2_slot4", "okay");
+			fdt_status_okay_by_alias(fdt, "emi2_slot4");
 			break;
 		case EMI2_SLOT5:
-			fdt_set_node_status(fdt, "emi2_slot5", "okay");
+			fdt_status_okay_by_alias(fdt, "emi2_slot5");
 			break;
 		}
 	}
diff --git a/common/fdt_support.c b/common/fdt_support.c
index 46aa842..16854f6 100644
--- a/common/fdt_support.c
+++ b/common/fdt_support.c
@@ -2,7 +2,7 @@
  * (C) Copyright 2007
  * Gerald Van Baren, Custom IDEAS, vanbaren@cideas.com
  *
- * Copyright 2010 Freescale Semiconductor, Inc.
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
  *
  * See file CREDITS for list of people who contributed to this
  * project.
@@ -1255,6 +1255,64 @@ int fdt_create_phandle(void *fdt, int nodeoffset)
 	return phandle;
 }
 
+/*
+ * fdt_set_node_status: Set status for the given node
+ *
+ * @fdt: ptr to device tree
+ * @nodeoffset: node to update
+ * @status: FDT_STATUS_OKAY, FDT_STATUS_DISABLED,
+ *	    FDT_STATUS_FAIL, FDT_STATUS_FAIL_ERROR_CODE
+ * @error_code: optional, only used if status is FDT_STATUS_FAIL_ERROR_CODE
+ */
+int fdt_set_node_status(void *fdt, int nodeoffset,
+			enum fdt_status status, unsigned int error_code)
+{
+	char buf[16];
+	int ret = 0;
+
+	if (nodeoffset < 0)
+		return nodeoffset;
+
+	switch (status) {
+	case FDT_STATUS_OKAY:
+		ret = fdt_setprop_string(fdt, nodeoffset, "status", "okay");
+		break;
+	case FDT_STATUS_DISABLED:
+		ret = fdt_setprop_string(fdt, nodeoffset, "status", "disabled");
+		break;
+	case FDT_STATUS_FAIL:
+		ret = fdt_setprop_string(fdt, nodeoffset, "status", "fail");
+		break;
+	case FDT_STATUS_FAIL_ERROR_CODE:
+		sprintf(buf, "fail-%d", error_code);
+		ret = fdt_setprop_string(fdt, nodeoffset, "status", buf);
+		break;
+	default:
+		printf("Invalid fdt status: %x\n", status);
+		ret = -1;
+		break;
+	}
+
+	return ret;
+}
+
+/*
+ * fdt_set_status_by_alias: Set status for the given node given an alias
+ *
+ * @fdt: ptr to device tree
+ * @alias: alias of node to update
+ * @status: FDT_STATUS_OKAY, FDT_STATUS_DISABLED,
+ *	    FDT_STATUS_FAIL, FDT_STATUS_FAIL_ERROR_CODE
+ * @error_code: optional, only used if status is FDT_STATUS_FAIL_ERROR_CODE
+ */
+int fdt_set_status_by_alias(void *fdt, const char* alias,
+			    enum fdt_status status, unsigned int error_code)
+{
+	int offset = fdt_path_offset(fdt, alias);
+
+	return fdt_set_node_status(fdt, offset, status, error_code);
+}
+
 #if defined(CONFIG_VIDEO)
 int fdt_add_edid(void *blob, const char *compat, unsigned char *edid_buf)
 {
diff --git a/include/fdt_support.h b/include/fdt_support.h
index 8f06aac..08b4de1 100644
--- a/include/fdt_support.h
+++ b/include/fdt_support.h
@@ -97,5 +97,33 @@ int fdt_verify_alias_address(void *fdt, int anode, const char *alias,
 			      u64 addr);
 u64 fdt_get_base_address(void *fdt, int node);
 
+enum fdt_status {
+	FDT_STATUS_OKAY,
+	FDT_STATUS_DISABLED,
+	FDT_STATUS_FAIL,
+	FDT_STATUS_FAIL_ERROR_CODE,
+};
+int fdt_set_node_status(void *fdt, int nodeoffset,
+			enum fdt_status status, unsigned int error_code);
+static inline int fdt_status_okay(void *fdt, int nodeoffset)
+{
+	return fdt_set_node_status(fdt, nodeoffset, FDT_STATUS_OKAY, 0);
+}
+static inline int fdt_status_disabled(void *fdt, int nodeoffset)
+{
+	return fdt_set_node_status(fdt, nodeoffset, FDT_STATUS_DISABLED, 0);
+}
+
+int fdt_set_status_by_alias(void *fdt, const char* alias,
+			    enum fdt_status status, unsigned int error_code);
+static inline int fdt_status_okay_by_alias(void *fdt, const char* alias)
+{
+	return fdt_set_status_by_alias(fdt, alias, FDT_STATUS_OKAY, 0);
+}
+static inline int fdt_status_disabled_by_alias(void *fdt, const char* alias)
+{
+	return fdt_set_status_by_alias(fdt, alias, FDT_STATUS_DISABLED, 0);
+}
+
 #endif /* ifdef CONFIG_OF_LIBFDT */
 #endif /* ifndef __FDT_SUPPORT_H */
-- 
1.7.3.4

[U-Boot] [PATCH 2/2] powerpc/85xx: Update USB device tree status based on pin settings

[Kumar Gala]

From: Shengzhou Liu <Shengzhou.Liu@freescale.com>

For P3060 and P4080, USB pins are multiplexed with other functions.
Update the device tree status for USB ports based on setting of
RCW[EC1] & RCW[EC2] which describe if pins are muxed to usb.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 arch/powerpc/cpu/mpc85xx/fdt.c |   23 +++++++++++++++++++++++
 1 files changed, 23 insertions(+), 0 deletions(-)

diff --git a/arch/powerpc/cpu/mpc85xx/fdt.c b/arch/powerpc/cpu/mpc85xx/fdt.c
index d20c94c..5c85a4f 100644
--- a/arch/powerpc/cpu/mpc85xx/fdt.c
+++ b/arch/powerpc/cpu/mpc85xx/fdt.c
@@ -538,6 +538,27 @@ void fdt_fixup_fman_firmware(void *blob)
 #define fdt_fixup_fman_firmware(x)
 #endif
 
+#if defined(CONFIG_PPC_P4080) || defined(CONFIG_PPC_P3060)
+static void fdt_fixup_usb(void *fdt)
+{
+	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	u32 rcwsr11 = in_be32(&gur->rcwsr[11]);
+	int off;
+
+	off = fdt_node_offset_by_compatible(fdt, -1, "fsl,mpc85xx-usb2-mph");
+	if ((rcwsr11 & FSL_CORENET_RCWSR11_EC1) !=
+				FSL_CORENET_RCWSR11_EC1_FM1_USB1)
+		fdt_status_disabled(fdt, off);
+
+	off = fdt_node_offset_by_compatible(fdt, -1, "fsl,mpc85xx-usb2-dr");
+	if ((rcwsr11 & FSL_CORENET_RCWSR11_EC2) !=
+				FSL_CORENET_RCWSR11_EC2_USB2)
+		fdt_status_disabled(fdt, off);
+}
+#else
+#define fdt_fixup_usb(x)
+#endif
+
 void ft_cpu_setup(void *blob, bd_t *bd)
 {
 	int off;
@@ -642,6 +663,8 @@ void ft_cpu_setup(void *blob, bd_t *bd)
 
 	do_fixup_by_compat_u32(blob, "fsl,flexcan-v1.0",
 			"clock_freq", gd->bus_clk, 1);
+
+	fdt_fixup_usb(blob);
 }
 
 /*
-- 
1.7.3.4

[U-Boot] [PATCH 1/2] fdt: Add new fdt_set_node_status & fdt_set_status_by_alias helpers

[Jerry Van Baren]

Hi Kumar, Shengzhou,

On 10/14/2011 03:10 PM, Kumar Gala wrote:
> From: Shengzhou Liu<Shengzhou.Liu@freescale.com>
>
> Add common function fdt_set_node_status() to assist in various locations
> that we set a nodes status.  This function utilizes the status values
> that are part of the EPAPR spec (on power.org).
>
> fdt_set_status_by_alias() is based on fdt_set_node_status() but uses an
> alias string to identify the node to update.
>
> We also add some shortcut functions to help the common cases of setting
> "okay" and "disabled":
>
> 	fdt_status_okay()
> 	fdt_status_disabled()
> 	fdt_status_okay_by_alias()
> 	fdt_status_disabled_by_alias()
>
> Finally, we fixup the corenet_ds ethernet code which previously had
> a function by the same name that can be replaced with the new helpers.
>
> Signed-off-by: Shengzhou Liu<Shengzhou.Liu@freescale.com>
> Signed-off-by: Kumar Gala<galak@kernel.crashing.org>
> ---
>   board/freescale/corenet_ds/eth_hydra.c |   26 ++------------
>   board/freescale/corenet_ds/eth_p4080.c |   36 +++++--------------
>   common/fdt_support.c                   |   60 +++++++++++++++++++++++++++++++-
>   include/fdt_support.h                  |   28 +++++++++++++++
>   4 files changed, 101 insertions(+), 49 deletions(-)

While this touches fdt_support.[ch] which is nominally "mine", it is 
coupled with the Freescale support.  I could make you break it into two, 
but then I would have to do more work and you (and wd) would have to 
make sure they went into u-boot in the right order.  That sounds ugly, 
so I would prefer Kumar apply it to his subrepo to feed into u-boot.

Acked-by: Gerald Van Baren <vanbaren@cideas.com>

Best regards,
gvb

[snip]

[U-Boot] [PATCH 1/2] fdt: Add new fdt_set_node_status & fdt_set_status_by_alias helpers

[Kumar Gala]

On Oct 15, 2011, at 8:04 AM, Jerry Van Baren wrote:

> Hi Kumar, Shengzhou,
> 
> On 10/14/2011 03:10 PM, Kumar Gala wrote:
>> From: Shengzhou Liu<Shengzhou.Liu@freescale.com>
>> 
>> Add common function fdt_set_node_status() to assist in various locations
>> that we set a nodes status.  This function utilizes the status values
>> that are part of the EPAPR spec (on power.org).
>> 
>> fdt_set_status_by_alias() is based on fdt_set_node_status() but uses an
>> alias string to identify the node to update.
>> 
>> We also add some shortcut functions to help the common cases of setting
>> "okay" and "disabled":
>> 
>> 	fdt_status_okay()
>> 	fdt_status_disabled()
>> 	fdt_status_okay_by_alias()
>> 	fdt_status_disabled_by_alias()
>> 
>> Finally, we fixup the corenet_ds ethernet code which previously had
>> a function by the same name that can be replaced with the new helpers.
>> 
>> Signed-off-by: Shengzhou Liu<Shengzhou.Liu@freescale.com>
>> Signed-off-by: Kumar Gala<galak@kernel.crashing.org>
>> ---
>>  board/freescale/corenet_ds/eth_hydra.c |   26 ++------------
>>  board/freescale/corenet_ds/eth_p4080.c |   36 +++++--------------
>>  common/fdt_support.c                   |   60 +++++++++++++++++++++++++++++++-
>>  include/fdt_support.h                  |   28 +++++++++++++++
>>  4 files changed, 101 insertions(+), 49 deletions(-)
> 
> While this touches fdt_support.[ch] which is nominally "mine", it is coupled with the Freescale support.  I could make you break it into two, but then I would have to do more work and you (and wd) would have to make sure they went into u-boot in the right order.  That sounds ugly, so I would prefer Kumar apply it to his subrepo to feed into u-boot.
> 
> Acked-by: Gerald Van Baren <vanbaren@cideas.com>
> 
> Best regards,
> gvb

applied to 85xx

- k

[U-Boot] [PATCH 2/2] powerpc/85xx: Update USB device tree status based on pin settings

[Kumar Gala]

On Oct 14, 2011, at 2:10 PM, Kumar Gala wrote:

> From: Shengzhou Liu <Shengzhou.Liu@freescale.com>
> 
> For P3060 and P4080, USB pins are multiplexed with other functions.
> Update the device tree status for USB ports based on setting of
> RCW[EC1] & RCW[EC2] which describe if pins are muxed to usb.
> 
> Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
> ---
> arch/powerpc/cpu/mpc85xx/fdt.c |   23 +++++++++++++++++++++++
> 1 files changed, 23 insertions(+), 0 deletions(-)

applied to 85xx

- k

[U-Boot] [PATCH 1/2] fdt: Add new fdt_set_node_status & fdt_set_status_by_alias helpers

[Wolfgang Denk]

Dear Kumar Gala,

In message <1318619444-2059-1-git-send-email-galak@kernel.crashing.org> you wrote:
> From: Shengzhou Liu <Shengzhou.Liu@freescale.com>
> 
> Add common function fdt_set_node_status() to assist in various locations
> that we set a nodes status.  This function utilizes the status values
> that are part of the EPAPR spec (on power.org).
> 
> fdt_set_status_by_alias() is based on fdt_set_node_status() but uses an
> alias string to identify the node to update.
> 
> We also add some shortcut functions to help the common cases of setting
> "okay" and "disabled":
> 
> 	fdt_status_okay()
> 	fdt_status_disabled()
> 	fdt_status_okay_by_alias()
> 	fdt_status_disabled_by_alias()
> 
> Finally, we fixup the corenet_ds ethernet code which previously had
> a function by the same name that can be replaced with the new helpers.
> 
> Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

This patch breaks a number of boards by growing the code size even for
boards which never make use of this new stuff.

Affected boards: TQM8555 TQM8541

[Building with ELDK 4.2]:

+ ./MAKEALL TQM8555
Configuring for TQM8555 - Board: TQM85xx, Options: MPC8555,TQM8555=y,HOSTNAME=tqm8555,BOARDNAME="TQM8555"
ppc_6xx-ld: warning: dot moved backwards before `.bss'
ppc_6xx-ld: warning: dot moved backwards before `.bss'
ppc_6xx-ld: u-boot: section .text lma 0xfffc0000 overlaps previous sections
ppc_6xx-ld: u-boot: section .rodata lma 0xfffef388 overlaps previous sections
ppc_6xx-ld: u-boot: section .reloc lma 0xffffa400 overlaps previous sections
ppc_6xx-ld: u-boot: section .data lma 0xffffcd3c overlaps previous sections
ppc_6xx-ld: u-boot: section .u_boot_cmd lma 0xffffea68 overlaps previous sections
ppc_6xx-ld: u-boot: section .bootpg lma 0xfffff0dc overlaps previous sections


Please fix.

Best regards,

Wolfgang Denk

-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Each honest calling, each walk of life, has its own  elite,  its  own
aristocracy based on excellence of performance. - James Bryant Conant

[U-Boot] [PATCH 1/2] fdt: Add new fdt_set_node_status & fdt_set_status_by_alias helpers

[Kumar Gala]

On Oct 23, 2011, at 3:49 AM, Wolfgang Denk wrote:

> Dear Kumar Gala,
> 
> In message <1318619444-2059-1-git-send-email-galak@kernel.crashing.org> you wrote:
>> From: Shengzhou Liu <Shengzhou.Liu@freescale.com>
>> 
>> Add common function fdt_set_node_status() to assist in various locations
>> that we set a nodes status.  This function utilizes the status values
>> that are part of the EPAPR spec (on power.org).
>> 
>> fdt_set_status_by_alias() is based on fdt_set_node_status() but uses an
>> alias string to identify the node to update.
>> 
>> We also add some shortcut functions to help the common cases of setting
>> "okay" and "disabled":
>> 
>> 	fdt_status_okay()
>> 	fdt_status_disabled()
>> 	fdt_status_okay_by_alias()
>> 	fdt_status_disabled_by_alias()
>> 
>> Finally, we fixup the corenet_ds ethernet code which previously had
>> a function by the same name that can be replaced with the new helpers.
>> 
>> Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
>> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
> 
> This patch breaks a number of boards by growing the code size even for
> boards which never make use of this new stuff.
> 
> Affected boards: TQM8555 TQM8541
> 
> [Building with ELDK 4.2]:
> 
> + ./MAKEALL TQM8555
> Configuring for TQM8555 - Board: TQM85xx, Options: MPC8555,TQM8555=y,HOSTNAME=tqm8555,BOARDNAME="TQM8555"
> ppc_6xx-ld: warning: dot moved backwards before `.bss'
> ppc_6xx-ld: warning: dot moved backwards before `.bss'
> ppc_6xx-ld: u-boot: section .text lma 0xfffc0000 overlaps previous sections
> ppc_6xx-ld: u-boot: section .rodata lma 0xfffef388 overlaps previous sections
> ppc_6xx-ld: u-boot: section .reloc lma 0xffffa400 overlaps previous sections
> ppc_6xx-ld: u-boot: section .data lma 0xffffcd3c overlaps previous sections
> ppc_6xx-ld: u-boot: section .u_boot_cmd lma 0xffffea68 overlaps previous sections
> ppc_6xx-ld: u-boot: section .bootpg lma 0xfffff0dc overlaps previous sections


Is part of our issue with older gcc-4.2 toolchain that the linker doesn't garbage collect unused functions?

- k

[U-Boot] [PATCH 1/2] fdt: Add new fdt_set_node_status & fdt_set_status_by_alias helpers

[Wolfgang Denk]

Dear Kumar Gala,

In message <8D0C487D-8573-4556-AD02-60DAF1104C38@kernel.crashing.org> you wrote:
> 
> > [Building with ELDK 4.2]:
...
> Is part of our issue with older gcc-4.2 toolchain that the linker
> doesn't garbage collect unused functions?

Which binutils version is minimally needed?  ElDK 4.2 uses GNU ld
version 2.17.50.0.12 20070128 ...

Best regards,

Wolfgang Denk

-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
I am more bored than you could ever possibly be.  Go back to work.