[U-Boot] [PATCH 0/8][v2] DaVinci EMAC for AM35x and HTKW mcx board support

[U-Boot] [PATCH 0/8][v2] DaVinci EMAC for AM35x and HTKW mcx board support

[Ilya Yanok]

Hello,

These series bring support of DaVinci EMAC interface on TI AM35xx
processors as well as support for HTKW mcx board which uses it.
Changes:
 1. Common defines and register definitions moved to
drivers/net/davinci_emac.h
 2. Added coding/decoding of internal RAM addresses.
 3. DaVinci-specific PHY parts moved under #ifdefs.
 4. Added support for running with D-Cache enabled.
 5. Speed is hardcoded to 100Mbps. This definetely needs a better
solution but somehow existing code causes troubles.
 6. AM35xx-specific defines added into the separate header.
 7. AM3517 specific mux defines moved to common header.

Regards,

Signed-off-by: Ilya Yanok <yanok@emcraft.com>

[U-Boot] [PATCH 1/8] davinci_emac: move arch-independent defines to separate header

[Ilya Yanok]

DaVinci EMAC is found not only on DaVinci SoCs but on some OMAP3 SoCs
also. This patch moves common defines from arch-davinci/emac_defs.h to
drivers/net/davinci_emac.h

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
 arch/arm/include/asm/arch-davinci/emac_defs.h |  293 -----------------------
 drivers/net/davinci_emac.c                    |    1 +
 drivers/net/davinci_emac.h                    |  318 +++++++++++++++++++++++++
 3 files changed, 319 insertions(+), 293 deletions(-)
 create mode 100644 drivers/net/davinci_emac.h

diff --git a/arch/arm/include/asm/arch-davinci/emac_defs.h b/arch/arm/include/asm/arch-davinci/emac_defs.h
index 294a9a8..8a17de9 100644
--- a/arch/arm/include/asm/arch-davinci/emac_defs.h
+++ b/arch/arm/include/asm/arch-davinci/emac_defs.h
@@ -84,299 +84,6 @@
 #define EMAC_MDIO_CLOCK_FREQ		2000000		/* 2.0 MHz */
 #endif
 
-/* PHY mask - set only those phy number bits where phy is/can be connected */
-#define EMAC_MDIO_PHY_NUM           CONFIG_EMAC_MDIO_PHY_NUM
-#define EMAC_MDIO_PHY_MASK          (1 << EMAC_MDIO_PHY_NUM)
-
-/* Ethernet Min/Max packet size */
-#define EMAC_MIN_ETHERNET_PKT_SIZE	60
-#define EMAC_MAX_ETHERNET_PKT_SIZE	1518
-#define EMAC_PKT_ALIGN			18	/* 1518 + 18 = 1536 (packet aligned on 32 byte boundry) */
-
-/* Number of RX packet buffers
- * NOTE: Only 1 buffer supported as of now
- */
-#define EMAC_MAX_RX_BUFFERS		10
-
-
-/***********************************************
- ******** Internally used macros ***************
- ***********************************************/
-
-#define EMAC_CH_TX			1
-#define EMAC_CH_RX			0
-
-/* Each descriptor occupies 4 words, lets start RX desc's@0 and
- * reserve space for 64 descriptors max
- */
-#define EMAC_RX_DESC_BASE		0x0
-#define EMAC_TX_DESC_BASE		0x1000
-
-/* EMAC Teardown value */
-#define EMAC_TEARDOWN_VALUE		0xfffffffc
-
-/* MII Status Register */
-#define MII_STATUS_REG			1
-
-/* Number of statistics registers */
-#define EMAC_NUM_STATS			36
-
-
-/* EMAC Descriptor */
-typedef volatile struct _emac_desc
-{
-	u_int32_t	next;		/* Pointer to next descriptor in chain */
-	u_int8_t	*buffer;	/* Pointer to data buffer */
-	u_int32_t	buff_off_len;	/* Buffer Offset(MSW) and Length(LSW) */
-	u_int32_t	pkt_flag_len;	/* Packet Flags(MSW) and Length(LSW) */
-} emac_desc;
-
-/* CPPI bit positions */
-#define EMAC_CPPI_SOP_BIT		(0x80000000)
-#define EMAC_CPPI_EOP_BIT		(0x40000000)
-#define EMAC_CPPI_OWNERSHIP_BIT		(0x20000000)
-#define EMAC_CPPI_EOQ_BIT		(0x10000000)
-#define EMAC_CPPI_TEARDOWN_COMPLETE_BIT	(0x08000000)
-#define EMAC_CPPI_PASS_CRC_BIT		(0x04000000)
-
-#define EMAC_CPPI_RX_ERROR_FRAME	(0x03fc0000)
-
-#define EMAC_MACCONTROL_MIIEN_ENABLE		(0x20)
-#define EMAC_MACCONTROL_FULLDUPLEX_ENABLE	(0x1)
-#define EMAC_MACCONTROL_GIGABIT_ENABLE		(1 << 7)
-#define EMAC_MACCONTROL_GIGFORCE		(1 << 17)
-#define EMAC_MACCONTROL_RMIISPEED_100		(1 << 15)
-
-#define EMAC_MAC_ADDR_MATCH		(1 << 19)
-#define EMAC_MAC_ADDR_IS_VALID		(1 << 20)
-
-#define EMAC_RXMBPENABLE_RXCAFEN_ENABLE	(0x200000)
-#define EMAC_RXMBPENABLE_RXBROADEN	(0x2000)
-
-
-#define MDIO_CONTROL_IDLE		(0x80000000)
-#define MDIO_CONTROL_ENABLE		(0x40000000)
-#define MDIO_CONTROL_FAULT_ENABLE	(0x40000)
-#define MDIO_CONTROL_FAULT		(0x80000)
-#define MDIO_USERACCESS0_GO		(0x80000000)
-#define MDIO_USERACCESS0_WRITE_READ	(0x0)
-#define MDIO_USERACCESS0_WRITE_WRITE	(0x40000000)
-#define MDIO_USERACCESS0_ACK		(0x20000000)
-
-/* Ethernet MAC Registers Structure */
-typedef struct  {
-	dv_reg		TXIDVER;
-	dv_reg		TXCONTROL;
-	dv_reg		TXTEARDOWN;
-	u_int8_t	RSVD0[4];
-	dv_reg		RXIDVER;
-	dv_reg		RXCONTROL;
-	dv_reg		RXTEARDOWN;
-	u_int8_t	RSVD1[100];
-	dv_reg		TXINTSTATRAW;
-	dv_reg		TXINTSTATMASKED;
-	dv_reg		TXINTMASKSET;
-	dv_reg		TXINTMASKCLEAR;
-	dv_reg		MACINVECTOR;
-	u_int8_t	RSVD2[12];
-	dv_reg		RXINTSTATRAW;
-	dv_reg		RXINTSTATMASKED;
-	dv_reg		RXINTMASKSET;
-	dv_reg		RXINTMASKCLEAR;
-	dv_reg		MACINTSTATRAW;
-	dv_reg		MACINTSTATMASKED;
-	dv_reg		MACINTMASKSET;
-	dv_reg		MACINTMASKCLEAR;
-	u_int8_t	RSVD3[64];
-	dv_reg		RXMBPENABLE;
-	dv_reg		RXUNICASTSET;
-	dv_reg		RXUNICASTCLEAR;
-	dv_reg		RXMAXLEN;
-	dv_reg		RXBUFFEROFFSET;
-	dv_reg		RXFILTERLOWTHRESH;
-	u_int8_t	RSVD4[8];
-	dv_reg		RX0FLOWTHRESH;
-	dv_reg		RX1FLOWTHRESH;
-	dv_reg		RX2FLOWTHRESH;
-	dv_reg		RX3FLOWTHRESH;
-	dv_reg		RX4FLOWTHRESH;
-	dv_reg		RX5FLOWTHRESH;
-	dv_reg		RX6FLOWTHRESH;
-	dv_reg		RX7FLOWTHRESH;
-	dv_reg		RX0FREEBUFFER;
-	dv_reg		RX1FREEBUFFER;
-	dv_reg		RX2FREEBUFFER;
-	dv_reg		RX3FREEBUFFER;
-	dv_reg		RX4FREEBUFFER;
-	dv_reg		RX5FREEBUFFER;
-	dv_reg		RX6FREEBUFFER;
-	dv_reg		RX7FREEBUFFER;
-	dv_reg		MACCONTROL;
-	dv_reg		MACSTATUS;
-	dv_reg		EMCONTROL;
-	dv_reg		FIFOCONTROL;
-	dv_reg		MACCONFIG;
-	dv_reg		SOFTRESET;
-	u_int8_t	RSVD5[88];
-	dv_reg		MACSRCADDRLO;
-	dv_reg		MACSRCADDRHI;
-	dv_reg		MACHASH1;
-	dv_reg		MACHASH2;
-	dv_reg		BOFFTEST;
-	dv_reg		TPACETEST;
-	dv_reg		RXPAUSE;
-	dv_reg		TXPAUSE;
-	u_int8_t	RSVD6[16];
-	dv_reg		RXGOODFRAMES;
-	dv_reg		RXBCASTFRAMES;
-	dv_reg		RXMCASTFRAMES;
-	dv_reg		RXPAUSEFRAMES;
-	dv_reg		RXCRCERRORS;
-	dv_reg		RXALIGNCODEERRORS;
-	dv_reg		RXOVERSIZED;
-	dv_reg		RXJABBER;
-	dv_reg		RXUNDERSIZED;
-	dv_reg		RXFRAGMENTS;
-	dv_reg		RXFILTERED;
-	dv_reg		RXQOSFILTERED;
-	dv_reg		RXOCTETS;
-	dv_reg		TXGOODFRAMES;
-	dv_reg		TXBCASTFRAMES;
-	dv_reg		TXMCASTFRAMES;
-	dv_reg		TXPAUSEFRAMES;
-	dv_reg		TXDEFERRED;
-	dv_reg		TXCOLLISION;
-	dv_reg		TXSINGLECOLL;
-	dv_reg		TXMULTICOLL;
-	dv_reg		TXEXCESSIVECOLL;
-	dv_reg		TXLATECOLL;
-	dv_reg		TXUNDERRUN;
-	dv_reg		TXCARRIERSENSE;
-	dv_reg		TXOCTETS;
-	dv_reg		FRAME64;
-	dv_reg		FRAME65T127;
-	dv_reg		FRAME128T255;
-	dv_reg		FRAME256T511;
-	dv_reg		FRAME512T1023;
-	dv_reg		FRAME1024TUP;
-	dv_reg		NETOCTETS;
-	dv_reg		RXSOFOVERRUNS;
-	dv_reg		RXMOFOVERRUNS;
-	dv_reg		RXDMAOVERRUNS;
-	u_int8_t	RSVD7[624];
-	dv_reg		MACADDRLO;
-	dv_reg		MACADDRHI;
-	dv_reg		MACINDEX;
-	u_int8_t	RSVD8[244];
-	dv_reg		TX0HDP;
-	dv_reg		TX1HDP;
-	dv_reg		TX2HDP;
-	dv_reg		TX3HDP;
-	dv_reg		TX4HDP;
-	dv_reg		TX5HDP;
-	dv_reg		TX6HDP;
-	dv_reg		TX7HDP;
-	dv_reg		RX0HDP;
-	dv_reg		RX1HDP;
-	dv_reg		RX2HDP;
-	dv_reg		RX3HDP;
-	dv_reg		RX4HDP;
-	dv_reg		RX5HDP;
-	dv_reg		RX6HDP;
-	dv_reg		RX7HDP;
-	dv_reg		TX0CP;
-	dv_reg		TX1CP;
-	dv_reg		TX2CP;
-	dv_reg		TX3CP;
-	dv_reg		TX4CP;
-	dv_reg		TX5CP;
-	dv_reg		TX6CP;
-	dv_reg		TX7CP;
-	dv_reg		RX0CP;
-	dv_reg		RX1CP;
-	dv_reg		RX2CP;
-	dv_reg		RX3CP;
-	dv_reg		RX4CP;
-	dv_reg		RX5CP;
-	dv_reg		RX6CP;
-	dv_reg		RX7CP;
-} emac_regs;
-
-/* EMAC Wrapper Registers Structure */
-typedef struct  {
-#ifdef DAVINCI_EMAC_VERSION2
-	dv_reg		idver;
-	dv_reg		softrst;
-	dv_reg		emctrl;
-	dv_reg		c0rxthreshen;
-	dv_reg		c0rxen;
-	dv_reg		c0txen;
-	dv_reg		c0miscen;
-	dv_reg		c1rxthreshen;
-	dv_reg		c1rxen;
-	dv_reg		c1txen;
-	dv_reg		c1miscen;
-	dv_reg		c2rxthreshen;
-	dv_reg		c2rxen;
-	dv_reg		c2txen;
-	dv_reg		c2miscen;
-	dv_reg		c0rxthreshstat;
-	dv_reg		c0rxstat;
-	dv_reg		c0txstat;
-	dv_reg		c0miscstat;
-	dv_reg		c1rxthreshstat;
-	dv_reg		c1rxstat;
-	dv_reg		c1txstat;
-	dv_reg		c1miscstat;
-	dv_reg		c2rxthreshstat;
-	dv_reg		c2rxstat;
-	dv_reg		c2txstat;
-	dv_reg		c2miscstat;
-	dv_reg		c0rximax;
-	dv_reg		c0tximax;
-	dv_reg		c1rximax;
-	dv_reg		c1tximax;
-	dv_reg		c2rximax;
-	dv_reg		c2tximax;
-#else
-	u_int8_t	RSVD0[4100];
-	dv_reg		EWCTL;
-	dv_reg		EWINTTCNT;
-#endif
-} ewrap_regs;
-
-/* EMAC MDIO Registers Structure */
-typedef struct  {
-	dv_reg		VERSION;
-	dv_reg		CONTROL;
-	dv_reg		ALIVE;
-	dv_reg		LINK;
-	dv_reg		LINKINTRAW;
-	dv_reg		LINKINTMASKED;
-	u_int8_t	RSVD0[8];
-	dv_reg		USERINTRAW;
-	dv_reg		USERINTMASKED;
-	dv_reg		USERINTMASKSET;
-	dv_reg		USERINTMASKCLEAR;
-	u_int8_t	RSVD1[80];
-	dv_reg		USERACCESS0;
-	dv_reg		USERPHYSEL0;
-	dv_reg		USERACCESS1;
-	dv_reg		USERPHYSEL1;
-} mdio_regs;
-
-int davinci_eth_phy_read(u_int8_t phy_addr, u_int8_t reg_num, u_int16_t *data);
-int davinci_eth_phy_write(u_int8_t phy_addr, u_int8_t reg_num, u_int16_t data);
-
-typedef struct
-{
-	char	name[64];
-	int	(*init)(int phy_addr);
-	int	(*is_phy_connected)(int phy_addr);
-	int	(*get_link_speed)(int phy_addr);
-	int	(*auto_negotiate)(int phy_addr);
-} phy_t;
-
 #define PHY_KSZ8873	(0x00221450)
 int ksz8873_is_phy_connected(int phy_addr);
 int ksz8873_get_link_speed(int phy_addr);
diff --git a/drivers/net/davinci_emac.c b/drivers/net/davinci_emac.c
index a8905b8..0e980ec 100644
--- a/drivers/net/davinci_emac.c
+++ b/drivers/net/davinci_emac.c
@@ -43,6 +43,7 @@
 #include <malloc.h>
 #include <asm/arch/emac_defs.h>
 #include <asm/io.h>
+#include "davinci_emac.h"
 
 unsigned int	emac_dbg = 0;
 #define debug_emac(fmt,args...)	if (emac_dbg) printf(fmt,##args)
diff --git a/drivers/net/davinci_emac.h b/drivers/net/davinci_emac.h
new file mode 100644
index 0000000..a0d82ff
--- /dev/null
+++ b/drivers/net/davinci_emac.h
@@ -0,0 +1,318 @@
+/*
+ * Copyright (C) 2011 Ilya Yanok, Emcraft Systems
+ *
+ * Based on: mach-davinci/emac_defs.h
+ * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, write to the Free Software
+ *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef _DAVINCI_EMAC_H_
+#define _DAVINCI_EMAC_H_
+/* PHY mask - set only those phy number bits where phy is/can be connected */
+#define EMAC_MDIO_PHY_NUM           CONFIG_EMAC_MDIO_PHY_NUM
+#define EMAC_MDIO_PHY_MASK          (1 << EMAC_MDIO_PHY_NUM)
+
+/* Ethernet Min/Max packet size */
+#define EMAC_MIN_ETHERNET_PKT_SIZE	60
+#define EMAC_MAX_ETHERNET_PKT_SIZE	1518
+/* 1518 + 18 = 1536 (packet aligned on 32 byte boundry) */
+#define EMAC_PKT_ALIGN			18
+
+/* Number of RX packet buffers
+ * NOTE: Only 1 buffer supported as of now
+ */
+#define EMAC_MAX_RX_BUFFERS		10
+
+
+/***********************************************
+ ******** Internally used macros ***************
+ ***********************************************/
+
+#define EMAC_CH_TX			1
+#define EMAC_CH_RX			0
+
+/* Each descriptor occupies 4 words, lets start RX desc's@0 and
+ * reserve space for 64 descriptors max
+ */
+#define EMAC_RX_DESC_BASE		0x0
+#define EMAC_TX_DESC_BASE		0x1000
+
+/* EMAC Teardown value */
+#define EMAC_TEARDOWN_VALUE		0xfffffffc
+
+/* MII Status Register */
+#define MII_STATUS_REG			1
+
+/* Number of statistics registers */
+#define EMAC_NUM_STATS			36
+
+
+/* EMAC Descriptor */
+typedef volatile struct _emac_desc
+{
+	u_int32_t	next;		/* Pointer to next descriptor
+					   in chain */
+	u_int8_t	*buffer;	/* Pointer to data buffer */
+	u_int32_t	buff_off_len;	/* Buffer Offset(MSW) and Length(LSW) */
+	u_int32_t	pkt_flag_len;	/* Packet Flags(MSW) and Length(LSW) */
+} emac_desc;
+
+/* CPPI bit positions */
+#define EMAC_CPPI_SOP_BIT		(0x80000000)
+#define EMAC_CPPI_EOP_BIT		(0x40000000)
+#define EMAC_CPPI_OWNERSHIP_BIT		(0x20000000)
+#define EMAC_CPPI_EOQ_BIT		(0x10000000)
+#define EMAC_CPPI_TEARDOWN_COMPLETE_BIT	(0x08000000)
+#define EMAC_CPPI_PASS_CRC_BIT		(0x04000000)
+
+#define EMAC_CPPI_RX_ERROR_FRAME	(0x03fc0000)
+
+#define EMAC_MACCONTROL_MIIEN_ENABLE		(0x20)
+#define EMAC_MACCONTROL_FULLDUPLEX_ENABLE	(0x1)
+#define EMAC_MACCONTROL_GIGABIT_ENABLE		(1 << 7)
+#define EMAC_MACCONTROL_GIGFORCE		(1 << 17)
+#define EMAC_MACCONTROL_RMIISPEED_100		(1 << 15)
+
+#define EMAC_MAC_ADDR_MATCH		(1 << 19)
+#define EMAC_MAC_ADDR_IS_VALID		(1 << 20)
+
+#define EMAC_RXMBPENABLE_RXCAFEN_ENABLE	(0x200000)
+#define EMAC_RXMBPENABLE_RXBROADEN	(0x2000)
+
+
+#define MDIO_CONTROL_IDLE		(0x80000000)
+#define MDIO_CONTROL_ENABLE		(0x40000000)
+#define MDIO_CONTROL_FAULT_ENABLE	(0x40000)
+#define MDIO_CONTROL_FAULT		(0x80000)
+#define MDIO_USERACCESS0_GO		(0x80000000)
+#define MDIO_USERACCESS0_WRITE_READ	(0x0)
+#define MDIO_USERACCESS0_WRITE_WRITE	(0x40000000)
+#define MDIO_USERACCESS0_ACK		(0x20000000)
+
+/* Ethernet MAC Registers Structure */
+typedef struct  {
+	dv_reg		TXIDVER;
+	dv_reg		TXCONTROL;
+	dv_reg		TXTEARDOWN;
+	u_int8_t	RSVD0[4];
+	dv_reg		RXIDVER;
+	dv_reg		RXCONTROL;
+	dv_reg		RXTEARDOWN;
+	u_int8_t	RSVD1[100];
+	dv_reg		TXINTSTATRAW;
+	dv_reg		TXINTSTATMASKED;
+	dv_reg		TXINTMASKSET;
+	dv_reg		TXINTMASKCLEAR;
+	dv_reg		MACINVECTOR;
+	u_int8_t	RSVD2[12];
+	dv_reg		RXINTSTATRAW;
+	dv_reg		RXINTSTATMASKED;
+	dv_reg		RXINTMASKSET;
+	dv_reg		RXINTMASKCLEAR;
+	dv_reg		MACINTSTATRAW;
+	dv_reg		MACINTSTATMASKED;
+	dv_reg		MACINTMASKSET;
+	dv_reg		MACINTMASKCLEAR;
+	u_int8_t	RSVD3[64];
+	dv_reg		RXMBPENABLE;
+	dv_reg		RXUNICASTSET;
+	dv_reg		RXUNICASTCLEAR;
+	dv_reg		RXMAXLEN;
+	dv_reg		RXBUFFEROFFSET;
+	dv_reg		RXFILTERLOWTHRESH;
+	u_int8_t	RSVD4[8];
+	dv_reg		RX0FLOWTHRESH;
+	dv_reg		RX1FLOWTHRESH;
+	dv_reg		RX2FLOWTHRESH;
+	dv_reg		RX3FLOWTHRESH;
+	dv_reg		RX4FLOWTHRESH;
+	dv_reg		RX5FLOWTHRESH;
+	dv_reg		RX6FLOWTHRESH;
+	dv_reg		RX7FLOWTHRESH;
+	dv_reg		RX0FREEBUFFER;
+	dv_reg		RX1FREEBUFFER;
+	dv_reg		RX2FREEBUFFER;
+	dv_reg		RX3FREEBUFFER;
+	dv_reg		RX4FREEBUFFER;
+	dv_reg		RX5FREEBUFFER;
+	dv_reg		RX6FREEBUFFER;
+	dv_reg		RX7FREEBUFFER;
+	dv_reg		MACCONTROL;
+	dv_reg		MACSTATUS;
+	dv_reg		EMCONTROL;
+	dv_reg		FIFOCONTROL;
+	dv_reg		MACCONFIG;
+	dv_reg		SOFTRESET;
+	u_int8_t	RSVD5[88];
+	dv_reg		MACSRCADDRLO;
+	dv_reg		MACSRCADDRHI;
+	dv_reg		MACHASH1;
+	dv_reg		MACHASH2;
+	dv_reg		BOFFTEST;
+	dv_reg		TPACETEST;
+	dv_reg		RXPAUSE;
+	dv_reg		TXPAUSE;
+	u_int8_t	RSVD6[16];
+	dv_reg		RXGOODFRAMES;
+	dv_reg		RXBCASTFRAMES;
+	dv_reg		RXMCASTFRAMES;
+	dv_reg		RXPAUSEFRAMES;
+	dv_reg		RXCRCERRORS;
+	dv_reg		RXALIGNCODEERRORS;
+	dv_reg		RXOVERSIZED;
+	dv_reg		RXJABBER;
+	dv_reg		RXUNDERSIZED;
+	dv_reg		RXFRAGMENTS;
+	dv_reg		RXFILTERED;
+	dv_reg		RXQOSFILTERED;
+	dv_reg		RXOCTETS;
+	dv_reg		TXGOODFRAMES;
+	dv_reg		TXBCASTFRAMES;
+	dv_reg		TXMCASTFRAMES;
+	dv_reg		TXPAUSEFRAMES;
+	dv_reg		TXDEFERRED;
+	dv_reg		TXCOLLISION;
+	dv_reg		TXSINGLECOLL;
+	dv_reg		TXMULTICOLL;
+	dv_reg		TXEXCESSIVECOLL;
+	dv_reg		TXLATECOLL;
+	dv_reg		TXUNDERRUN;
+	dv_reg		TXCARRIERSENSE;
+	dv_reg		TXOCTETS;
+	dv_reg		FRAME64;
+	dv_reg		FRAME65T127;
+	dv_reg		FRAME128T255;
+	dv_reg		FRAME256T511;
+	dv_reg		FRAME512T1023;
+	dv_reg		FRAME1024TUP;
+	dv_reg		NETOCTETS;
+	dv_reg		RXSOFOVERRUNS;
+	dv_reg		RXMOFOVERRUNS;
+	dv_reg		RXDMAOVERRUNS;
+	u_int8_t	RSVD7[624];
+	dv_reg		MACADDRLO;
+	dv_reg		MACADDRHI;
+	dv_reg		MACINDEX;
+	u_int8_t	RSVD8[244];
+	dv_reg		TX0HDP;
+	dv_reg		TX1HDP;
+	dv_reg		TX2HDP;
+	dv_reg		TX3HDP;
+	dv_reg		TX4HDP;
+	dv_reg		TX5HDP;
+	dv_reg		TX6HDP;
+	dv_reg		TX7HDP;
+	dv_reg		RX0HDP;
+	dv_reg		RX1HDP;
+	dv_reg		RX2HDP;
+	dv_reg		RX3HDP;
+	dv_reg		RX4HDP;
+	dv_reg		RX5HDP;
+	dv_reg		RX6HDP;
+	dv_reg		RX7HDP;
+	dv_reg		TX0CP;
+	dv_reg		TX1CP;
+	dv_reg		TX2CP;
+	dv_reg		TX3CP;
+	dv_reg		TX4CP;
+	dv_reg		TX5CP;
+	dv_reg		TX6CP;
+	dv_reg		TX7CP;
+	dv_reg		RX0CP;
+	dv_reg		RX1CP;
+	dv_reg		RX2CP;
+	dv_reg		RX3CP;
+	dv_reg		RX4CP;
+	dv_reg		RX5CP;
+	dv_reg		RX6CP;
+	dv_reg		RX7CP;
+} emac_regs;
+
+/* EMAC Wrapper Registers Structure */
+typedef struct  {
+#ifdef DAVINCI_EMAC_VERSION2
+	dv_reg		idver;
+	dv_reg		softrst;
+	dv_reg		emctrl;
+	dv_reg		c0rxthreshen;
+	dv_reg		c0rxen;
+	dv_reg		c0txen;
+	dv_reg		c0miscen;
+	dv_reg		c1rxthreshen;
+	dv_reg		c1rxen;
+	dv_reg		c1txen;
+	dv_reg		c1miscen;
+	dv_reg		c2rxthreshen;
+	dv_reg		c2rxen;
+	dv_reg		c2txen;
+	dv_reg		c2miscen;
+	dv_reg		c0rxthreshstat;
+	dv_reg		c0rxstat;
+	dv_reg		c0txstat;
+	dv_reg		c0miscstat;
+	dv_reg		c1rxthreshstat;
+	dv_reg		c1rxstat;
+	dv_reg		c1txstat;
+	dv_reg		c1miscstat;
+	dv_reg		c2rxthreshstat;
+	dv_reg		c2rxstat;
+	dv_reg		c2txstat;
+	dv_reg		c2miscstat;
+	dv_reg		c0rximax;
+	dv_reg		c0tximax;
+	dv_reg		c1rximax;
+	dv_reg		c1tximax;
+	dv_reg		c2rximax;
+	dv_reg		c2tximax;
+#else
+	u_int8_t	RSVD0[4100];
+	dv_reg		EWCTL;
+	dv_reg		EWINTTCNT;
+#endif
+} ewrap_regs;
+
+/* EMAC MDIO Registers Structure */
+typedef struct  {
+	dv_reg		VERSION;
+	dv_reg		CONTROL;
+	dv_reg		ALIVE;
+	dv_reg		LINK;
+	dv_reg		LINKINTRAW;
+	dv_reg		LINKINTMASKED;
+	u_int8_t	RSVD0[8];
+	dv_reg		USERINTRAW;
+	dv_reg		USERINTMASKED;
+	dv_reg		USERINTMASKSET;
+	dv_reg		USERINTMASKCLEAR;
+	u_int8_t	RSVD1[80];
+	dv_reg		USERACCESS0;
+	dv_reg		USERPHYSEL0;
+	dv_reg		USERACCESS1;
+	dv_reg		USERPHYSEL1;
+} mdio_regs;
+
+int davinci_eth_phy_read(u_int8_t phy_addr, u_int8_t reg_num, u_int16_t *data);
+int davinci_eth_phy_write(u_int8_t phy_addr, u_int8_t reg_num, u_int16_t data);
+
+typedef struct {
+	char	name[64];
+	int	(*init)(int phy_addr);
+	int	(*is_phy_connected)(int phy_addr);
+	int	(*get_link_speed)(int phy_addr);
+	int	(*auto_negotiate)(int phy_addr);
+} phy_t;
+
+#endif /* _DAVINCI_EMAC_H_ */
-- 
1.7.6.2

[U-Boot] [PATCH 2/8] davinci_emac: use internal addresses in buffer descriptors

[Ilya Yanok]

On AM35xx CPPI RAM had different addresses when accessed from the CPU
and from the EMAC. We need to account this to deal with the buffer
descriptors correctly.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
 drivers/net/davinci_emac.c |   39 ++++++++++++++++++++++++++++++---------
 1 files changed, 30 insertions(+), 9 deletions(-)

diff --git a/drivers/net/davinci_emac.c b/drivers/net/davinci_emac.c
index 0e980ec..3c442c4 100644
--- a/drivers/net/davinci_emac.c
+++ b/drivers/net/davinci_emac.c
@@ -48,6 +48,27 @@
 unsigned int	emac_dbg = 0;
 #define debug_emac(fmt,args...)	if (emac_dbg) printf(fmt,##args)
 
+#ifdef EMAC_HW_RAM_ADDR
+static inline unsigned long BD_TO_HW(unsigned long x)
+{
+	if (x == 0)
+		return 0;
+
+	return x - EMAC_WRAPPER_RAM_ADDR + EMAC_HW_RAM_ADDR;
+}
+
+static inline unsigned long HW_TO_BD(unsigned long x)
+{
+	if (x == 0)
+		return 0;
+
+	return x - EMAC_HW_RAM_ADDR + EMAC_WRAPPER_RAM_ADDR;
+}
+#else
+#define BD_TO_HW(x)	(x)
+#define HW_TO_BD(x)	(x)
+#endif
+
 #ifdef DAVINCI_EMAC_GIG_ENABLE
 #define emac_gigabit_enable()	davinci_eth_gigabit_enable()
 #else
@@ -389,7 +410,7 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis)
 	/* Create RX queue and set receive process in place */
 	emac_rx_active_head = emac_rx_desc;
 	for (cnt = 0; cnt < EMAC_MAX_RX_BUFFERS; cnt++) {
-		rx_desc->next = (u_int32_t)(rx_desc + 1);
+		rx_desc->next = BD_TO_HW((u_int32_t)(rx_desc + 1));
 		rx_desc->buffer = &emac_rx_buffers[cnt * (EMAC_MAX_ETHERNET_PKT_SIZE + EMAC_PKT_ALIGN)];
 		rx_desc->buff_off_len = EMAC_MAX_ETHERNET_PKT_SIZE;
 		rx_desc->pkt_flag_len = EMAC_CPPI_OWNERSHIP_BIT;
@@ -441,7 +462,7 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis)
 	emac_gigabit_enable();
 
 	/* Start receive process */
-	writel((u_int32_t)emac_rx_desc, &adap_emac->RX0HDP);
+	writel(BD_TO_HW((u_int32_t)emac_rx_desc), &adap_emac->RX0HDP);
 
 	debug_emac("- emac_open\n");
 
@@ -559,7 +580,7 @@ static int davinci_eth_send_packet (struct eth_device *dev,
 				      EMAC_CPPI_OWNERSHIP_BIT |
 				      EMAC_CPPI_EOP_BIT);
 	/* Send the packet */
-	writel((unsigned long)emac_tx_desc, &adap_emac->TX0HDP);
+	writel(BD_TO_HW((unsigned long)emac_tx_desc), &adap_emac->TX0HDP);
 
 	/* Wait for packet to complete or link down */
 	while (1) {
@@ -603,14 +624,14 @@ static int davinci_eth_rcv_packet (struct eth_device *dev)
 		}
 
 		/* Ack received packet descriptor */
-		writel((unsigned long)rx_curr_desc, &adap_emac->RX0CP);
+		writel(BD_TO_HW((ulong)rx_curr_desc), &adap_emac->RX0CP);
 		curr_desc = rx_curr_desc;
 		emac_rx_active_head =
-			(volatile emac_desc *) rx_curr_desc->next;
+			(volatile emac_desc *) (HW_TO_BD(rx_curr_desc->next));
 
 		if (status & EMAC_CPPI_EOQ_BIT) {
 			if (emac_rx_active_head) {
-				writel((unsigned long)emac_rx_active_head,
+				writel(BD_TO_HW((ulong)emac_rx_active_head),
 				       &adap_emac->RX0HDP);
 			} else {
 				emac_rx_queue_active = 0;
@@ -628,7 +649,7 @@ static int davinci_eth_rcv_packet (struct eth_device *dev)
 			emac_rx_active_head = curr_desc;
 			emac_rx_active_tail = curr_desc;
 			if (emac_rx_queue_active != 0) {
-				writel((unsigned long)emac_rx_active_head,
+				writel(BD_TO_HW((ulong)emac_rx_active_head),
 				       &adap_emac->RX0HDP);
 				printf ("INFO: emac_rcv_pkt: active queue head = 0, HDP fired\n");
 				emac_rx_queue_active = 1;
@@ -636,10 +657,10 @@ static int davinci_eth_rcv_packet (struct eth_device *dev)
 		} else {
 			tail_desc = emac_rx_active_tail;
 			emac_rx_active_tail = curr_desc;
-			tail_desc->next = (unsigned int) curr_desc;
+			tail_desc->next = BD_TO_HW((ulong) curr_desc);
 			status = tail_desc->pkt_flag_len;
 			if (status & EMAC_CPPI_EOQ_BIT) {
-				writel((unsigned long)curr_desc,
+				writel(BD_TO_HW((ulong)curr_desc),
 				       &adap_emac->RX0HDP);
 				status &= ~EMAC_CPPI_EOQ_BIT;
 				tail_desc->pkt_flag_len = status;
-- 
1.7.6.2

[U-Boot] [PATCH 3/8] davinci_emac: conditionally compile specific PHY support

[Ilya Yanok]

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
 drivers/net/davinci_emac.c |    8 ++++++++
 1 files changed, 8 insertions(+), 0 deletions(-)

diff --git a/drivers/net/davinci_emac.c b/drivers/net/davinci_emac.c
index 3c442c4..d413478 100644
--- a/drivers/net/davinci_emac.c
+++ b/drivers/net/davinci_emac.c
@@ -736,6 +736,7 @@ int davinci_emac_initialize(void)
 	phy_id |= tmp & 0x0000ffff;
 
 	switch (phy_id) {
+#ifdef PHY_KSZ8873
 	case PHY_KSZ8873:
 		sprintf(phy.name, "KSZ8873 @ 0x%02x", active_phy_addr);
 		phy.init = ksz8873_init_phy;
@@ -743,6 +744,8 @@ int davinci_emac_initialize(void)
 		phy.get_link_speed = ksz8873_get_link_speed;
 		phy.auto_negotiate = ksz8873_auto_negotiate;
 		break;
+#endif
+#ifdef PHY_LXT972
 		case PHY_LXT972:
 			sprintf(phy.name, "LXT972 @ 0x%02x", active_phy_addr);
 			phy.init = lxt972_init_phy;
@@ -750,6 +753,8 @@ int davinci_emac_initialize(void)
 			phy.get_link_speed = lxt972_get_link_speed;
 			phy.auto_negotiate = lxt972_auto_negotiate;
 			break;
+#endif
+#ifdef PHY_DP83848
 		case PHY_DP83848:
 			sprintf(phy.name, "DP83848 @ 0x%02x", active_phy_addr);
 			phy.init = dp83848_init_phy;
@@ -757,6 +762,8 @@ int davinci_emac_initialize(void)
 			phy.get_link_speed = dp83848_get_link_speed;
 			phy.auto_negotiate = dp83848_auto_negotiate;
 			break;
+#endif
+#ifdef PHY_ET1011C
 		case PHY_ET1011C:
 			sprintf(phy.name, "ET1011C @ 0x%02x", active_phy_addr);
 			phy.init = gen_init_phy;
@@ -764,6 +771,7 @@ int davinci_emac_initialize(void)
 			phy.get_link_speed = et1011c_get_link_speed;
 			phy.auto_negotiate = gen_auto_negotiate;
 			break;
+#endif
 		default:
 			sprintf(phy.name, "GENERIC @ 0x%02x", active_phy_addr);
 			phy.init = gen_init_phy;
-- 
1.7.6.2

[U-Boot] [PATCH 4/8] davinci_emac: fix for running with dcache enabled

[Ilya Yanok]

DaVinci EMAC is present on TI AM35xx SoCs (ARMv7) which run with D-Cache
enabled by default. So we have to take care and flush/invalidate the
cache before/after the DMA operations.

Please note that the receive buffer alignment to 32 byte boundary comes
from the old driver version I don't know if it is really needed or
alignment to cache line size is enough.

!!!NOTE!!! This actually breaks builds for all DaVinci boards that use
this driver (as there is no {invalidate,flush}_dcache_range for
ARM926EJS).

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
 drivers/net/davinci_emac.c |   41 +++++++++++++++++++++++++++++++++++++++--
 drivers/net/davinci_emac.h |    5 +++--
 2 files changed, 42 insertions(+), 4 deletions(-)

diff --git a/drivers/net/davinci_emac.c b/drivers/net/davinci_emac.c
index d413478..4318a39 100644
--- a/drivers/net/davinci_emac.c
+++ b/drivers/net/davinci_emac.c
@@ -41,6 +41,7 @@
 #include <net.h>
 #include <miiphy.h>
 #include <malloc.h>
+#include <linux/compiler.h>
 #include <asm/arch/emac_defs.h>
 #include <asm/io.h>
 #include "davinci_emac.h"
@@ -100,13 +101,34 @@ static volatile emac_desc	*emac_rx_active_tail = 0;
 static int			emac_rx_queue_active = 0;
 
 /* Receive packet buffers */
-static unsigned char		emac_rx_buffers[EMAC_MAX_RX_BUFFERS * (EMAC_MAX_ETHERNET_PKT_SIZE + EMAC_PKT_ALIGN)];
+static unsigned char emac_rx_buffers[EMAC_MAX_RX_BUFFERS * EMAC_RXBUF_SIZE]
+				__aligned(CONFIG_SYS_CACHELINE_SIZE);
 
 /* PHY address for a discovered PHY (0xff - not found) */
 static volatile u_int8_t	active_phy_addr = 0xff;
 
 phy_t				phy;
 
+static inline void davinci_flush_rx_descs(void)
+{
+	/* flush the whole RX descs area */
+	flush_dcache_range(EMAC_WRAPPER_RAM_ADDR + EMAC_RX_DESC_BASE,
+			EMAC_WRAPPER_RAM_ADDR + EMAC_TX_DESC_BASE);
+}
+
+static inline void davinci_invalidate_rx_descs(void)
+{
+	/* invalidate the whole RX descs area */
+	invalidate_dcache_range(EMAC_WRAPPER_RAM_ADDR + EMAC_RX_DESC_BASE,
+			EMAC_WRAPPER_RAM_ADDR + EMAC_TX_DESC_BASE);
+}
+
+static inline void davinci_flush_desc(emac_desc *desc)
+{
+	flush_dcache_range((unsigned long)desc,
+			(unsigned long)desc + sizeof(*desc));
+}
+
 static int davinci_eth_set_mac_addr(struct eth_device *dev)
 {
 	unsigned long		mac_hi;
@@ -411,7 +433,7 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis)
 	emac_rx_active_head = emac_rx_desc;
 	for (cnt = 0; cnt < EMAC_MAX_RX_BUFFERS; cnt++) {
 		rx_desc->next = BD_TO_HW((u_int32_t)(rx_desc + 1));
-		rx_desc->buffer = &emac_rx_buffers[cnt * (EMAC_MAX_ETHERNET_PKT_SIZE + EMAC_PKT_ALIGN)];
+		rx_desc->buffer = &emac_rx_buffers[cnt * EMAC_RXBUF_SIZE];
 		rx_desc->buff_off_len = EMAC_MAX_ETHERNET_PKT_SIZE;
 		rx_desc->pkt_flag_len = EMAC_CPPI_OWNERSHIP_BIT;
 		rx_desc++;
@@ -423,6 +445,8 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis)
 	emac_rx_active_tail = rx_desc;
 	emac_rx_queue_active = 1;
 
+	davinci_flush_rx_descs();
+
 	/* Enable TX/RX */
 	writel(EMAC_MAX_ETHERNET_PKT_SIZE, &adap_emac->RXMAXLEN);
 	writel(0, &adap_emac->RXBUFFEROFFSET);
@@ -579,6 +603,11 @@ static int davinci_eth_send_packet (struct eth_device *dev,
 				      EMAC_CPPI_SOP_BIT |
 				      EMAC_CPPI_OWNERSHIP_BIT |
 				      EMAC_CPPI_EOP_BIT);
+
+	flush_dcache_range((unsigned long)packet,
+			(unsigned long)packet + length);
+	davinci_flush_desc(emac_tx_desc);
+
 	/* Send the packet */
 	writel(BD_TO_HW((unsigned long)emac_tx_desc), &adap_emac->TX0HDP);
 
@@ -611,6 +640,8 @@ static int davinci_eth_rcv_packet (struct eth_device *dev)
 	volatile emac_desc *tail_desc;
 	int status, ret = -1;
 
+	davinci_invalidate_rx_descs();
+
 	rx_curr_desc = emac_rx_active_head;
 	status = rx_curr_desc->pkt_flag_len;
 	if ((rx_curr_desc) && ((status & EMAC_CPPI_OWNERSHIP_BIT) == 0)) {
@@ -618,6 +649,9 @@ static int davinci_eth_rcv_packet (struct eth_device *dev)
 			/* Error in packet - discard it and requeue desc */
 			printf ("WARN: emac_rcv_pkt: Error in packet\n");
 		} else {
+			unsigned long tmp = (unsigned long)rx_curr_desc->buffer;
+
+			invalidate_dcache_range(tmp, tmp + EMAC_RXBUF_SIZE);
 			NetReceive (rx_curr_desc->buffer,
 				    (rx_curr_desc->buff_off_len & 0xffff));
 			ret = rx_curr_desc->buff_off_len & 0xffff;
@@ -643,6 +677,7 @@ static int davinci_eth_rcv_packet (struct eth_device *dev)
 		rx_curr_desc->buff_off_len = EMAC_MAX_ETHERNET_PKT_SIZE;
 		rx_curr_desc->pkt_flag_len = EMAC_CPPI_OWNERSHIP_BIT;
 		rx_curr_desc->next = 0;
+		davinci_flush_desc(rx_curr_desc);
 
 		if (emac_rx_active_head == 0) {
 			printf ("INFO: emac_rcv_pkt: active queue head = 0\n");
@@ -660,11 +695,13 @@ static int davinci_eth_rcv_packet (struct eth_device *dev)
 			tail_desc->next = BD_TO_HW((ulong) curr_desc);
 			status = tail_desc->pkt_flag_len;
 			if (status & EMAC_CPPI_EOQ_BIT) {
+				davinci_flush_desc(tail_desc);
 				writel(BD_TO_HW((ulong)curr_desc),
 				       &adap_emac->RX0HDP);
 				status &= ~EMAC_CPPI_EOQ_BIT;
 				tail_desc->pkt_flag_len = status;
 			}
+			davinci_flush_desc(tail_desc);
 		}
 		return (ret);
 	}
diff --git a/drivers/net/davinci_emac.h b/drivers/net/davinci_emac.h
index a0d82ff..9d47303 100644
--- a/drivers/net/davinci_emac.h
+++ b/drivers/net/davinci_emac.h
@@ -28,8 +28,9 @@
 /* Ethernet Min/Max packet size */
 #define EMAC_MIN_ETHERNET_PKT_SIZE	60
 #define EMAC_MAX_ETHERNET_PKT_SIZE	1518
-/* 1518 + 18 = 1536 (packet aligned on 32 byte boundry) */
-#define EMAC_PKT_ALIGN			18
+/* Buffer size (should be aligned on 32 byte and cache line) */
+#define EMAC_RXBUF_SIZE	ALIGN(ALIGN(EMAC_MAX_ETHERNET_PKT_SIZE, 32),\
+				CONFIG_SYS_CACHELINE_SIZE)
 
 /* Number of RX packet buffers
  * NOTE: Only 1 buffer supported as of now
-- 
1.7.6.2

[U-Boot] [PATCH 5/8] davinci_emac: hardcode 100Mbps for AM35xx and RMII

[Ilya Yanok]

For some reason code setting the speed based on the PHY feedback causes
troubles on AM3517 so hardcode 100Mbps for now.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
 drivers/net/davinci_emac.c |    3 ++-
 1 files changed, 2 insertions(+), 1 deletions(-)

diff --git a/drivers/net/davinci_emac.c b/drivers/net/davinci_emac.c
index 4318a39..a35ebeb 100644
--- a/drivers/net/davinci_emac.c
+++ b/drivers/net/davinci_emac.c
@@ -461,7 +461,8 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis)
 	writel(1, &adap_emac->RXUNICASTSET);
 
 	/* Enable MII interface and Full duplex mode */
-#ifdef CONFIG_SOC_DA8XX
+#if defined(CONFIG_SOC_DA8XX) || \
+	(defined(CONFIG_OMAP34XX) && defined(CONFIG_DRIVER_TI_EMAC_USE_RMII))
 	writel((EMAC_MACCONTROL_MIIEN_ENABLE |
 		EMAC_MACCONTROL_FULLDUPLEX_ENABLE |
 		EMAC_MACCONTROL_RMIISPEED_100),
-- 
1.7.6.2

[U-Boot] [PATCH 6/8] AM35xx: add EMAC support

[Ilya Yanok]

AM35xx has DaVinci-compatible EMAC.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
 arch/arm/cpu/armv7/omap3/Makefile           |    1 +
 arch/arm/cpu/armv7/omap3/emac.c             |   37 ++++++++++++++++++
 arch/arm/include/asm/arch-omap3/emac_defs.h |   56 +++++++++++++++++++++++++++
 3 files changed, 94 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/cpu/armv7/omap3/emac.c
 create mode 100644 arch/arm/include/asm/arch-omap3/emac_defs.h

diff --git a/arch/arm/cpu/armv7/omap3/Makefile b/arch/arm/cpu/armv7/omap3/Makefile
index 8e85891..6ebfd32 100644
--- a/arch/arm/cpu/armv7/omap3/Makefile
+++ b/arch/arm/cpu/armv7/omap3/Makefile
@@ -32,6 +32,7 @@ COBJS	+= clock.o
 COBJS	+= mem.o
 COBJS	+= sys_info.o
 
+COBJS-$(CONFIG_DRIVER_TI_EMAC)	+= emac.o
 COBJS-$(CONFIG_EMIF4)	+= emif4.o
 COBJS-$(CONFIG_SDRC)	+= sdrc.o
 
diff --git a/arch/arm/cpu/armv7/omap3/emac.c b/arch/arm/cpu/armv7/omap3/emac.c
new file mode 100644
index 0000000..71b4424
--- /dev/null
+++ b/arch/arm/cpu/armv7/omap3/emac.c
@@ -0,0 +1,37 @@
+/*
+ *
+ * DaVinci EMAC initialization.
+ *
+ * (C) Copyright 2011, Ilya Yanok, Emcraft Systems
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc.
+ */
+
+#include <common.h>
+#include <netdev.h>
+
+/*
+ * Initializes on-chip ethernet controllers.
+ * to override, implement board_eth_init()
+ */
+int cpu_eth_init(bd_t *bis)
+{
+	davinci_emac_initialize();
+
+	return 0;
+}
diff --git a/arch/arm/include/asm/arch-omap3/emac_defs.h b/arch/arm/include/asm/arch-omap3/emac_defs.h
new file mode 100644
index 0000000..8506c55
--- /dev/null
+++ b/arch/arm/include/asm/arch-omap3/emac_defs.h
@@ -0,0 +1,56 @@
+/*
+ * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
+ *
+ * Based on:
+ *
+ * ----------------------------------------------------------------------------
+ *
+ * dm644x_emac.h
+ *
+ * TI DaVinci (DM644X) EMAC peripheral driver header for DV-EVM
+ *
+ * Copyright (C) 2005 Texas Instruments.
+ *
+ * ----------------------------------------------------------------------------
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, write to the Free Software
+ *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ * ----------------------------------------------------------------------------
+
+ * Modifications:
+ * ver. 1.0: Sep 2005, TI PSP Team - Created EMAC version for uBoot.
+ *
+ */
+
+#ifndef _AM3517_EMAC_H_
+#define _AM3517_EMAC_H_
+
+#define EMAC_BASE_ADDR                 0x5C010000
+#define EMAC_WRAPPER_BASE_ADDR         0x5C000000
+#define EMAC_WRAPPER_RAM_ADDR          0x5C020000
+#define EMAC_MDIO_BASE_ADDR            0x5C030000
+#define EMAC_HW_RAM_ADDR               0x01E20000
+
+#define EMAC_MDIO_BUS_FREQ             166000000       /* 166 MHZ check */
+#define EMAC_MDIO_CLOCK_FREQ           1000000         /* 2.0 MHz */
+
+/* SOFTRESET macro definition interferes with emac_regs structure definition */
+#undef SOFTRESET
+
+typedef volatile unsigned int	dv_reg;
+typedef volatile unsigned int	*dv_reg_p;
+
+#define DAVINCI_EMAC_VERSION2
+
+#endif  /* _AM3517_EMAC_H_ */
-- 
1.7.6.2

[U-Boot] [PATCH 7/8] AM3517: move AM3517 specific mux defines to generic header

[Ilya Yanok]

AM3517 specific CONTROL_PADCONF_* defines moved from board-specific
files to <asm/arch-omap3/mux.h>

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
 arch/arm/include/asm/arch-omap3/mux.h |   41 +++++++++++++++++++++++++++++++++
 board/logicpd/am3517evm/am3517evm.h   |   40 --------------------------------
 board/ti/am3517crane/am3517crane.h    |   39 -------------------------------
 3 files changed, 41 insertions(+), 79 deletions(-)

diff --git a/arch/arm/include/asm/arch-omap3/mux.h b/arch/arm/include/asm/arch-omap3/mux.h
index 0c01c73..6daef49 100644
--- a/arch/arm/include/asm/arch-omap3/mux.h
+++ b/arch/arm/include/asm/arch-omap3/mux.h
@@ -404,6 +404,47 @@
 #define CONTROL_PADCONF_SDRC_CKE0	0x0262
 #define CONTROL_PADCONF_SDRC_CKE1	0x0264
 
+/* AM3517 specific mux configuration */
+#define CONTROL_PADCONF_SYS_NRESWARM	0x0A08
+/* CCDC */
+#define CONTROL_PADCONF_CCDC_PCLK	0x01E4
+#define CONTROL_PADCONF_CCDC_FIELD	0x01E6
+#define CONTROL_PADCONF_CCDC_HD		0x01E8
+#define CONTROL_PADCONF_CCDC_VD		0x01EA
+#define CONTROL_PADCONF_CCDC_WEN	0x01EC
+#define CONTROL_PADCONF_CCDC_DATA0	0x01EE
+#define CONTROL_PADCONF_CCDC_DATA1	0x01F0
+#define CONTROL_PADCONF_CCDC_DATA2	0x01F2
+#define CONTROL_PADCONF_CCDC_DATA3	0x01F4
+#define CONTROL_PADCONF_CCDC_DATA4	0x01F6
+#define CONTROL_PADCONF_CCDC_DATA5	0x01F8
+#define CONTROL_PADCONF_CCDC_DATA6	0x01FA
+#define CONTROL_PADCONF_CCDC_DATA7	0x01FC
+/* RMII */
+#define CONTROL_PADCONF_RMII_MDIO_DATA	0x01FE
+#define CONTROL_PADCONF_RMII_MDIO_CLK	0x0200
+#define CONTROL_PADCONF_RMII_RXD0	0x0202
+#define CONTROL_PADCONF_RMII_RXD1	0x0204
+#define CONTROL_PADCONF_RMII_CRS_DV	0x0206
+#define CONTROL_PADCONF_RMII_RXER	0x0208
+#define CONTROL_PADCONF_RMII_TXD0	0x020A
+#define CONTROL_PADCONF_RMII_TXD1	0x020C
+#define CONTROL_PADCONF_RMII_TXEN	0x020E
+#define CONTROL_PADCONF_RMII_50MHZ_CLK	0x0210
+#define CONTROL_PADCONF_USB0_DRVBUS	0x0212
+/* CAN */
+#define CONTROL_PADCONF_HECC1_TXD	0x0214
+#define CONTROL_PADCONF_HECC1_RXD	0x0216
+
+#define CONTROL_PADCONF_SYS_BOOT7	0x0218
+#define CONTROL_PADCONF_SDRC_DQS0N	0x021A
+#define CONTROL_PADCONF_SDRC_DQS1N	0x021C
+#define CONTROL_PADCONF_SDRC_DQS2N	0x021E
+#define CONTROL_PADCONF_SDRC_DQS3N	0x0220
+#define CONTROL_PADCONF_STRBEN_DLY0	0x0222
+#define CONTROL_PADCONF_STRBEN_DLY1	0x0224
+#define CONTROL_PADCONF_SYS_BOOT8	0x0226
+
 #define MUX_VAL(OFFSET,VALUE)\
 	writew((VALUE), OMAP34XX_CTRL_BASE + (OFFSET));
 
diff --git a/board/logicpd/am3517evm/am3517evm.h b/board/logicpd/am3517evm/am3517evm.h
index 3d74ef1..68d746c 100644
--- a/board/logicpd/am3517evm/am3517evm.h
+++ b/board/logicpd/am3517evm/am3517evm.h
@@ -31,46 +31,6 @@ const omap3_sysinfo sysinfo = {
 	"AM3517EVM Board",
 	"NAND",
 };
-/* AM3517 specific mux configuration */
-#define CONTROL_PADCONF_SYS_NRESWARM	0x0A08
-/* CCDC */
-#define CONTROL_PADCONF_CCDC_PCLK	0x01E4
-#define CONTROL_PADCONF_CCDC_FIELD	0x01E6
-#define CONTROL_PADCONF_CCDC_HD		0x01E8
-#define CONTROL_PADCONF_CCDC_VD		0x01EA
-#define CONTROL_PADCONF_CCDC_WEN	0x01EC
-#define CONTROL_PADCONF_CCDC_DATA0	0x01EE
-#define CONTROL_PADCONF_CCDC_DATA1	0x01F0
-#define CONTROL_PADCONF_CCDC_DATA2	0x01F2
-#define CONTROL_PADCONF_CCDC_DATA3	0x01F4
-#define CONTROL_PADCONF_CCDC_DATA4	0x01F6
-#define CONTROL_PADCONF_CCDC_DATA5	0x01F8
-#define CONTROL_PADCONF_CCDC_DATA6	0x01FA
-#define CONTROL_PADCONF_CCDC_DATA7	0x01FC
-/* RMII */
-#define CONTROL_PADCONF_RMII_MDIO_DATA	0x01FE
-#define CONTROL_PADCONF_RMII_MDIO_CLK	0x0200
-#define CONTROL_PADCONF_RMII_RXD0	0x0202
-#define CONTROL_PADCONF_RMII_RXD1	0x0204
-#define CONTROL_PADCONF_RMII_CRS_DV	0x0206
-#define CONTROL_PADCONF_RMII_RXER	0x0208
-#define CONTROL_PADCONF_RMII_TXD0	0x020A
-#define CONTROL_PADCONF_RMII_TXD1	0x020C
-#define CONTROL_PADCONF_RMII_TXEN	0x020E
-#define CONTROL_PADCONF_RMII_50MHZ_CLK	0x0210
-#define CONTROL_PADCONF_USB0_DRVBUS	0x0212
-/* CAN */
-#define CONTROL_PADCONF_HECC1_TXD	0x0214
-#define CONTROL_PADCONF_HECC1_RXD	0x0216
-
-#define CONTROL_PADCONF_SYS_BOOT7	0x0218
-#define CONTROL_PADCONF_SDRC_DQS0N	0x021A
-#define CONTROL_PADCONF_SDRC_DQS1N	0x021C
-#define CONTROL_PADCONF_SDRC_DQS2N	0x021E
-#define CONTROL_PADCONF_SDRC_DQS3N	0x0220
-#define CONTROL_PADCONF_STRBEN_DLY0	0x0222
-#define CONTROL_PADCONF_STRBEN_DLY1	0x0224
-#define CONTROL_PADCONF_SYS_BOOT8	0x0226
 
 /*
  * IEN  - Input Enable
diff --git a/board/ti/am3517crane/am3517crane.h b/board/ti/am3517crane/am3517crane.h
index 41db972..71335a3 100644
--- a/board/ti/am3517crane/am3517crane.h
+++ b/board/ti/am3517crane/am3517crane.h
@@ -30,45 +30,6 @@ const omap3_sysinfo sysinfo = {
 	"CraneBoard",
 	"NAND",
 };
-/* AM3517 specific mux configuration */
-#define CONTROL_PADCONF_SYS_NRESWARM	0x0A08
-/* CCDC */
-#define CONTROL_PADCONF_CCDC_PCLK	0x01E4
-#define CONTROL_PADCONF_CCDC_FIELD	0x01E6
-#define CONTROL_PADCONF_CCDC_HD		0x01E8
-#define CONTROL_PADCONF_CCDC_VD		0x01EA
-#define CONTROL_PADCONF_CCDC_WEN	0x01EC
-#define CONTROL_PADCONF_CCDC_DATA0	0x01EE
-#define CONTROL_PADCONF_CCDC_DATA1	0x01F0
-#define CONTROL_PADCONF_CCDC_DATA2	0x01F2
-#define CONTROL_PADCONF_CCDC_DATA3	0x01F4
-#define CONTROL_PADCONF_CCDC_DATA4	0x01F6
-#define CONTROL_PADCONF_CCDC_DATA5	0x01F8
-#define CONTROL_PADCONF_CCDC_DATA6	0x01FA
-#define CONTROL_PADCONF_CCDC_DATA7	0x01FC
-/* RMII */
-#define CONTROL_PADCONF_RMII_MDIO_DATA	0x01FE
-#define CONTROL_PADCONF_RMII_MDIO_CLK	0x0200
-#define CONTROL_PADCONF_RMII_RXD0	0x0202
-#define CONTROL_PADCONF_RMII_RXD1	0x0204
-#define CONTROL_PADCONF_RMII_CRS_DV	0x0206
-#define CONTROL_PADCONF_RMII_RXER	0x0208
-#define CONTROL_PADCONF_RMII_TXD0	0x020A
-#define CONTROL_PADCONF_RMII_TXD1	0x020C
-#define CONTROL_PADCONF_RMII_TXEN	0x020E
-#define CONTROL_PADCONF_RMII_50MHZ_CLK	0x0210
-#define CONTROL_PADCONF_USB0_DRVBUS	0x0212
-/* CAN */
-#define CONTROL_PADCONF_HECC1_TXD	0x0214
-#define CONTROL_PADCONF_HECC1_RXD	0x0216
-#define CONTROL_PADCONF_SYS_BOOT7	0x0218
-#define CONTROL_PADCONF_SDRC_DQS0N	0x021A
-#define CONTROL_PADCONF_SDRC_DQS1N	0x021C
-#define CONTROL_PADCONF_SDRC_DQS2N	0x021E
-#define CONTROL_PADCONF_SDRC_DQS3N	0x0220
-#define CONTROL_PADCONF_STRBEN_DLY0	0x0222
-#define CONTROL_PADCONF_STRBEN_DLY1	0x0224
-#define CONTROL_PADCONF_SYS_BOOT8	0x0226
 
 /*
  * IEN  - Input Enable
-- 
1.7.6.2

[U-Boot] [PATCH 8/8] mcx: support for HTKW mcx board

[Ilya Yanok]

This patch adds support for the HTKW mcx AM3517-based board.
Serial, Ethernet, NAND and MMC are supported.

Requires updated mach-types file.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
 MAINTAINERS             |    4 +
 board/htkw/mcx/Makefile |   44 +++++
 board/htkw/mcx/mcx.c    |   89 ++++++++++
 board/htkw/mcx/mcx.h    |  408 +++++++++++++++++++++++++++++++++++++++++++++++
 boards.cfg              |    1 +
 include/configs/mcx.h   |  315 ++++++++++++++++++++++++++++++++++++
 6 files changed, 861 insertions(+), 0 deletions(-)
 create mode 100644 board/htkw/mcx/Makefile
 create mode 100644 board/htkw/mcx/mcx.c
 create mode 100644 board/htkw/mcx/mcx.h
 create mode 100644 include/configs/mcx.h

diff --git a/MAINTAINERS b/MAINTAINERS
index bb95e6d..c09e19a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -878,6 +878,10 @@ Richard Woodruff <r-woodruff2@ti.com>
 
 	omap2420h4	ARM1136EJS
 
+Ilya Yanok <yanok@emcraft.com>
+
+	mcx		ARM ARMV7 (AM35x SoC)
+
 Syed Mohammed Khasim <sm.khasim@gmail.com>
 Sughosh Ganu <urwithsughosh@gmail.com>
 
diff --git a/board/htkw/mcx/Makefile b/board/htkw/mcx/Makefile
new file mode 100644
index 0000000..ce20ec7
--- /dev/null
+++ b/board/htkw/mcx/Makefile
@@ -0,0 +1,44 @@
+#
+# Copyright (C) 2011 Ilya Yanok, Emcraft Systems
+#
+# Based on ti/evm/Makefile
+#
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation; either version 2 of the License, or
+# (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc.
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS	:= $(BOARD).o
+
+SRCS	:= $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+clean:
+	rm -f $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
diff --git a/board/htkw/mcx/mcx.c b/board/htkw/mcx/mcx.c
new file mode 100644
index 0000000..00bd564
--- /dev/null
+++ b/board/htkw/mcx/mcx.c
@@ -0,0 +1,89 @@
+/*
+ * Copyright (C) 2011 Ilya Yanok, Emcraft Systems
+ *
+ * Based on ti/evm/evm.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc.
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-types.h>
+#include <asm/omap_gpio.h>
+#include <i2c.h>
+#include "mcx.h"
+
+#define AM3517_IP_SW_RESET	0x48002598
+#define CPGMACSS_SW_RST		(1 << 1)
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Routine: board_init
+ * Description: Early hardware init.
+ */
+int board_init(void)
+{
+	gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
+	/* boot param addr */
+	gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
+
+	return 0;
+}
+
+/*
+ * Routine: misc_init_r
+ * Description: Init i2c, ethernet, etc... (done here so udelay works)
+ */
+int misc_init_r(void)
+{
+#if defined(CONFIG_DRIVER_TI_EMAC)
+	u32 reset;
+#endif
+
+	dieid_num_r();
+
+#if defined(CONFIG_DRIVER_TI_EMAC)
+	/* ensure that the module is out of reset */
+	reset = readl(AM3517_IP_SW_RESET);
+	reset &= ~CPGMACSS_SW_RST;
+	writel(reset, AM3517_IP_SW_RESET);
+
+#endif
+	return 0;
+}
+
+/*
+ * Routine: set_muxconf_regs
+ * Description: Setting up the configuration Mux registers specific to the
+ *		hardware. Many pins need to be moved from protect to primary
+ *		mode.
+ */
+void set_muxconf_regs(void)
+{
+	MUX_MCX();
+}
+
+#if defined(CONFIG_GENERIC_MMC) && defined(CONFIG_OMAP_HSMMC)
+int board_mmc_init(bd_t *bis)
+{
+	omap_mmc_init(0);
+	return 0;
+}
+#endif
diff --git a/board/htkw/mcx/mcx.h b/board/htkw/mcx/mcx.h
new file mode 100644
index 0000000..d675a48
--- /dev/null
+++ b/board/htkw/mcx/mcx.h
@@ -0,0 +1,408 @@
+/*
+ * Copyright (C) 2011 Ilya Yanok, Emcraft Systems
+ *
+ * Based on ti/evm/evm.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc.
+ */
+
+#ifndef _AM3517EVM_H_
+#define _AM3517EVM_H_
+
+const omap3_sysinfo sysinfo = {
+	DDR_DISCRETE,
+	"HTKW mcx Board",
+	"NAND",
+};
+
+/*
+ * IEN  - Input Enable
+ * IDIS - Input Disable
+ * PTD  - Pull type Down
+ * PTU  - Pull type Up
+ * DIS  - Pull type selection is inactive
+ * EN   - Pull type selection is active
+ * M0   - Mode 0
+ * The commented string gives the final mux configuration for that pin
+ */
+#define MUX_MCX() \
+	/* SDRC */\
+	MUX_VAL(CP(SDRC_D0),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D1),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D2),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D3),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D4),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D5),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D6),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D7),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D8),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D9),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D10),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D11),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D12),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D13),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D14),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D15),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D16),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D17),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D18),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D19),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D20),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D21),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D22),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D23),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D24),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D25),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D26),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D27),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D28),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D29),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D30),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D31),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_CLK),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_DQS0),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_DQS1),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_DQS2),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_DQS3),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_DQS0N),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(SDRC_DQS1N),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(SDRC_DQS2N),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(SDRC_DQS3N),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(SDRC_CKE0),		(M0)) \
+	MUX_VAL(CP(SDRC_CKE1),		(M0)) \
+	MUX_VAL(CP(STRBEN_DLY0),	(IEN  | PTD | EN  | M0)) \
+					/*sdrc_strben_dly0*/\
+	MUX_VAL(CP(STRBEN_DLY1),	(IEN  | PTD | EN  | M0)) \
+					/*sdrc_strben_dly1*/\
+	/* GPMC */\
+	MUX_VAL(CP(GPMC_A1),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_A2),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_A3),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_A4),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_A5),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_A6),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_A7),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_A8),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_A9),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_A10),		(IDIS | PTU | DIS | M4)) \
+					/* GPIO_43 LCD buffer enable */ \
+	MUX_VAL(CP(GPMC_D0),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D1),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D2),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D3),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D4),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D5),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D6),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D7),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D8),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D9),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D10),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D11),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D12),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D13),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D14),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D15),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_NCS0),		(IDIS | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_NCS1),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_NCS2),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_NCS3),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_NCS4),		(IEN | PTU | EN  | M4))\
+	MUX_VAL(CP(GPMC_NCS5),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_NCS6),		(IEN | PTU | EN  | M4)) \
+					/* GPIO_57 TS_PenIRQn */\
+	MUX_VAL(CP(GPMC_NCS7),		(IEN | PTU | EN  | M4)) \
+					/* GPIO_58 ETHERNET RESET */\
+	MUX_VAL(CP(GPMC_CLK),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_NADV_ALE),	(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(GPMC_NOE),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(GPMC_NWE),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(GPMC_NBE0_CLE),	(IDIS | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_NBE1),		(IEN  | PTU | DIS  | M4)) \
+					/* GPIO_61 SD-CARD CD */ \
+	MUX_VAL(CP(GPMC_NWP),		(IDIS  | PTU | EN | M4)) \
+			/* GPIO_62 Nand write protect, keep enabled */ \
+	MUX_VAL(CP(GPMC_WAIT0),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_WAIT1),		(IEN | PTU | EN  | M4))\
+	MUX_VAL(CP(GPMC_WAIT2),		(IEN  | PTU | EN  | M4))\
+	MUX_VAL(CP(GPMC_WAIT3),		(IEN | PTU | EN  | M4)) \
+					/* GPIO_65 SD-CARD WP */\
+	/* DSS */\
+	MUX_VAL(CP(DSS_PCLK),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_HSYNC),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_VSYNC),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_ACBIAS),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA0),		(IEN | PTU | EN  | M4))\
+	MUX_VAL(CP(DSS_DATA1),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(DSS_DATA2),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(DSS_DATA3),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA4),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA5),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA6),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA7),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA8),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(DSS_DATA9),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(DSS_DATA10),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA11),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA12),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA13),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA14),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA15),		(IDIS | PTD | DIS | M0))\
+	MUX_VAL(CP(DSS_DATA16),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(DSS_DATA17),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(DSS_DATA18),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(DSS_DATA19),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA20),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA21),		(IDIS | PTD | DIS | M0))  \
+	MUX_VAL(CP(DSS_DATA22),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA23),		(IDIS | PTD | DIS | M0)) \
+	/* CAMERA */\
+	MUX_VAL(CP(CAM_HS),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(CAM_VS),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(CAM_XCLKA),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_PCLK),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(CAM_FLD),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D0),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D1),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D2),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D3),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D4),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D5),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D6),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D7),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D8),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D9),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D10),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D11),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_XCLKB),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_WEN),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_STROBE),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CSI2_DX0),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CSI2_DY0),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CSI2_DX1),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CSI2_DY1),		(IEN  | PTD | EN  | M4)) \
+	/* MMC */\
+	MUX_VAL(CP(MMC1_CLK),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(MMC1_CMD),		(IEN  | PTU | DIS | M0)) \
+	MUX_VAL(CP(MMC1_DAT0),		(IEN  | PTU | DIS | M0)) \
+	MUX_VAL(CP(MMC1_DAT1),		(IEN  | PTU | DIS | M0)) \
+	MUX_VAL(CP(MMC1_DAT2),		(IEN  | PTU | DIS | M0)) \
+	MUX_VAL(CP(MMC1_DAT3),		(IEN  | PTU | DIS | M0)) \
+	MUX_VAL(CP(MMC1_DAT4),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MMC1_DAT5),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MMC1_DAT6),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MMC1_DAT7),		(IEN  | PTU | EN  | M4)) \
+	\
+	MUX_VAL(CP(MMC2_CLK),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(MMC2_CMD),		(IDIS | PTD | DIS | M4)) \
+					/* GPIO_131 LCD Enable */ \
+	MUX_VAL(CP(MMC2_DAT0),		(IDIS | PTD | DIS  | M4)) \
+					/* GPIO_132 USB host Enable */\
+	MUX_VAL(CP(MMC2_DAT1),		(IDIS  | PTD | DIS  | M4)) \
+					/* GPIO_133 HDMI PD */\
+	MUX_VAL(CP(MMC2_DAT2),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MMC2_DAT3),		(IEN  | PTU | EN  | M4))\
+	/* McBSP */\
+	MUX_VAL(CP(MCBSP_CLKS),		(IEN  | PTU | DIS | M0)) \
+	MUX_VAL(CP(MCBSP1_CLKR),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(MCBSP1_FSR),		(IDIS | PTU | EN  | M0)) \
+	MUX_VAL(CP(MCBSP1_DX),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(MCBSP1_DR),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(MCBSP1_FSX),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(MCBSP1_CLKX),	(IEN  | PTD | DIS | M0)) \
+	\
+	MUX_VAL(CP(MCBSP2_FSX),		(IEN  | PTU | EN  | M4))\
+	MUX_VAL(CP(MCBSP2_CLKX),	(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MCBSP2_DR),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MCBSP2_DX),		(IEN  | PTU | EN  | M4))\
+	\
+	MUX_VAL(CP(MCBSP3_DX),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MCBSP3_DR),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MCBSP3_CLKX),	(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MCBSP3_FSX),		(IEN  | PTU | EN  | M4))\
+	\
+	MUX_VAL(CP(MCBSP4_CLKX),	(IDIS | PTD | DIS | M4)) \
+					/* GPIO_152 USB phy2 reset */\
+	MUX_VAL(CP(MCBSP4_DR),		(IEN | PTU | EN | M4)) \
+					/* GPIO_153 */\
+	MUX_VAL(CP(MCBSP4_DX),		(IDIS | PTD | DIS | M4)) \
+					/* GPIO_154 USB phy1 reset */\
+	MUX_VAL(CP(MCBSP4_FSX),		(IEN | PTU | EN | M4)) \
+					/* GPIO_155 TS_BUSY */\
+	/* UART */\
+	MUX_VAL(CP(UART1_TX),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(UART1_RTS),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(UART1_CTS),		(IEN  | PTU | DIS | M0)) \
+	MUX_VAL(CP(UART1_RX),		(IEN  | PTD | DIS | M0)) \
+	\
+	MUX_VAL(CP(UART2_CTS),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(UART2_RTS),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(UART2_TX),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(UART2_RX),		(IEN  | PTD | DIS | M0)) \
+	\
+	MUX_VAL(CP(UART3_CTS_RCTX),	(IEN  | PTU | DIS | M0)) \
+	MUX_VAL(CP(UART3_RTS_SD),	(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(UART3_RX_IRRX),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(UART3_TX_IRTX),	(IDIS | PTD | DIS | M0)) \
+	/* I2C */\
+	MUX_VAL(CP(I2C1_SCL),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(I2C1_SDA),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(I2C2_SCL),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(I2C2_SDA),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(I2C3_SCL),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(I2C3_SDA),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(I2C4_SCL),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(I2C4_SDA),		(IEN  | PTU | EN  | M0)) \
+	/* McSPI */\
+	MUX_VAL(CP(MCSPI1_CLK),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(MCSPI1_SIMO),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(MCSPI1_SOMI),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(MCSPI1_CS0),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(MCSPI1_CS1),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MCSPI1_CS2),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MCSPI1_CS3),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MCSPI2_CLK),		(IEN  | PTD | DIS | M3)) \
+					/* HSUSB2_dat7 */\
+	MUX_VAL(CP(MCSPI2_SIMO),	(IEN  | PTD | DIS | M3)) \
+					/* HSUSB2_dat4 */\
+	MUX_VAL(CP(MCSPI2_SOMI),	(IEN  | PTD | DIS | M3)) \
+					/* HSUSB2_dat5 */\
+	MUX_VAL(CP(MCSPI2_CS0),		(IEN  | PTD | DIS | M3)) \
+					/* HSUSB2_dat6 */\
+	MUX_VAL(CP(MCSPI2_CS1),		(IEN  | PTD | DIS | M3)) \
+					/* HSUSB2_dat3 */\
+	/* CCDC */\
+	MUX_VAL(CP(CCDC_PCLK),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_FIELD),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_HD),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_VD),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_WEN),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_DATA0),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_DATA1),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_DATA2),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_DATA3),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_DATA4),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_DATA5),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_DATA6),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_DATA7),		(IEN  | PTD | EN  | M4)) \
+	/* RMII */\
+	MUX_VAL(CP(RMII_MDIO_DATA),	(IEN  |  M0)) \
+	MUX_VAL(CP(RMII_MDIO_CLK),	(M0)) \
+	MUX_VAL(CP(RMII_RXD0),		(IEN  | PTD | M0)) \
+	MUX_VAL(CP(RMII_RXD1),		(IEN  | PTD | M0)) \
+	MUX_VAL(CP(RMII_CRS_DV),	(IEN  | PTD | M0)) \
+	MUX_VAL(CP(RMII_RXER),		(PTD | M0)) \
+	MUX_VAL(CP(RMII_TXD0),		(PTD | M0)) \
+	MUX_VAL(CP(RMII_TXD1),		(PTD | M0)) \
+	MUX_VAL(CP(RMII_TXEN),		(PTD | M0)) \
+	MUX_VAL(CP(RMII_50MHZ_CLK),	(IEN  | PTD | EN  | M0)) \
+	/* HECC */\
+	MUX_VAL(CP(HECC1_TXD),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(HECC1_RXD),		(IEN  | PTD | EN  | M4)) \
+	/* HSUSB */\
+	MUX_VAL(CP(HSUSB0_CLK),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(HSUSB0_STP),		(IDIS | PTU | EN  | M0)) \
+	MUX_VAL(CP(HSUSB0_DIR),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(HSUSB0_NXT),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(HSUSB0_DATA0),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(HSUSB0_DATA1),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(HSUSB0_DATA2),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(HSUSB0_DATA3),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(HSUSB0_DATA4),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(HSUSB0_DATA5),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(HSUSB0_DATA6),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(HSUSB0_DATA7),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(USB0_DRVBUS),	(IEN  | PTD | EN  | M0)) \
+	/* HDQ */\
+	MUX_VAL(CP(HDQ_SIO),		(IEN  | PTD | EN  | M4)) \
+	/* Control and debug */\
+	MUX_VAL(CP(SYS_32K),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(SYS_CLKREQ),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SYS_NIRQ),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(SYS_NRESWARM),	(IEN | PTU | DIS | M4)) \
+					/* SYS_nRESWARM */\
+	MUX_VAL(CP(SYS_BOOT0),		(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(SYS_BOOT1),		(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(SYS_BOOT2),		(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(SYS_BOOT3),		(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(SYS_BOOT4),		(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(SYS_BOOT5),		(IEN  | PTD | DIS | M4))\
+	MUX_VAL(CP(SYS_BOOT6),		(IEN  | PTD | DIS | M4))\
+	MUX_VAL(CP(SYS_BOOT7),		(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(SYS_BOOT8),		(IEN  | PTD | DIS | M4)) \
+	\
+	MUX_VAL(CP(SYS_OFF_MODE),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SYS_CLKOUT1),	(IEN  | PTD | DIS | M4))\
+	MUX_VAL(CP(SYS_CLKOUT2),	(IDIS | PTU | DIS | M4))\
+	/* JTAG */\
+	MUX_VAL(CP(JTAG_nTRST),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(JTAG_TCK),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(JTAG_TMS),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(JTAG_TDI),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(JTAG_EMU0),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(JTAG_EMU1),		(IEN | PTU | EN  | M4))\
+	/* ETK (ES2 onwards) */\
+	MUX_VAL(CP(ETK_CLK_ES2),	(IDIS  | PTD | DIS | M3)) \
+					/* hsusb1_stp */ \
+	MUX_VAL(CP(ETK_CTL_ES2),	(IDIS  | PTD | DIS | M3)) \
+					/* hsusb1_clk */\
+	MUX_VAL(CP(ETK_D0_ES2),		(IEN  | PTD | EN | M3)) \
+	MUX_VAL(CP(ETK_D1_ES2),		(IEN  | PTD | EN | M3)) \
+	MUX_VAL(CP(ETK_D2_ES2),		(IEN  | PTD | EN | M3)) \
+	MUX_VAL(CP(ETK_D3_ES2),		(IEN  | PTD | EN | M3)) \
+	MUX_VAL(CP(ETK_D4_ES2),		(IEN  | PTD | EN | M3)) \
+	MUX_VAL(CP(ETK_D5_ES2),		(IEN  | PTD | EN | M3)) \
+	MUX_VAL(CP(ETK_D6_ES2),		(IEN  | PTD | EN | M3)) \
+	MUX_VAL(CP(ETK_D7_ES2),		(IEN  | PTD | EN | M3)) \
+	MUX_VAL(CP(ETK_D8_ES2),		(IEN  | PTD | EN | M3)) \
+	MUX_VAL(CP(ETK_D9_ES2),		(IEN  | PTD | EN | M3)) \
+	MUX_VAL(CP(ETK_D10_ES2),	(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(ETK_D11_ES2),	(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(ETK_D13_ES2),	(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(ETK_D14_ES2),	(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(ETK_D15_ES2),	(IEN  | PTD | DIS | M4)) \
+	/* Die to Die */\
+	MUX_VAL(CP(D2D_MCAD34),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(D2D_MCAD35),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(D2D_MCAD36),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(D2D_CLK26MI),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_NRESPWRON),	(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(D2D_NRESWARM),	(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(D2D_ARM9NIRQ),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_UMA2P6FIQ),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_SPINT),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(D2D_FRINT),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(D2D_DMAREQ0),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_DMAREQ1),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_DMAREQ2),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_DMAREQ3),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_N3GTRST),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_N3GTDI),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_N3GTDO),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_N3GTMS),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_N3GTCK),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_N3GRTCK),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_MSTDBY),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(D2D_SWAKEUP),	(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(D2D_IDLEREQ),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_IDLEACK),	(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(D2D_MWRITE),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_SWRITE),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_MREAD),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_SREAD),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_MBUSFLAG),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_SBUSFLAG),	(IEN  | PTD | DIS | M0)) \
+
+#endif
diff --git a/boards.cfg b/boards.cfg
index d3d610d..7f656f6 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -183,6 +183,7 @@ omap3_beagle                 arm         armv7       beagle              ti
 omap3_evm                    arm         armv7       evm                 ti             omap3
 omap3_sdp3430                arm         armv7       sdp3430             ti             omap3
 devkit8000                   arm         armv7       devkit8000          timll          omap3
+mcx                          arm         armv7       mcx                 htkw           omap3
 omap4_panda                  arm         armv7       panda               ti             omap4
 omap4_sdp4430                arm         armv7       sdp4430             ti             omap4
 s5p_goni                     arm         armv7       goni                samsung        s5pc1xx
diff --git a/include/configs/mcx.h b/include/configs/mcx.h
new file mode 100644
index 0000000..434fb1c
--- /dev/null
+++ b/include/configs/mcx.h
@@ -0,0 +1,315 @@
+/*
+ * Copyright (C) 2011 Ilya Yanok, Emcraft Systems
+ *
+ * Based on omap3_evm_config.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_OMAP			/* in a TI OMAP core */
+#define CONFIG_OMAP34XX			/* which is a 34XX */
+#define CONFIG_OMAP3_MCX		/* working with mcx */
+
+#define CONFIG_MACH_TYPE	MACH_TYPE_MCX
+
+#define CONFIG_SYS_CACHELINE_SIZE	64
+
+#define CONFIG_EMIF4	/* The chip has EMIF4 controller */
+
+#include <asm/arch/cpu.h>		/* get chip and board defs */
+#include <asm/arch/omap3.h>
+
+#define CONFIG_OF_LIBFDT
+#define CONFIG_FIT
+
+#define CONFIG_SYS_TEXT_BASE		0x80008000
+
+/*
+ * Display CPU and Board information
+ */
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+/* Clock Defines */
+#define V_OSCK			26000000	/* Clock output from T2 */
+#define V_SCLK			(V_OSCK >> 1)
+
+#undef CONFIG_USE_IRQ				/* no support for IRQs */
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_CMDLINE_TAG			/* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_ENV_SIZE			(128 << 10)	/* 128 KiB sector */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (128 << 10))
+/*
+ * DDR related
+ */
+#define CONFIG_OMAP3_MICRON_DDR			/* Micron DDR */
+#define CONFIG_SYS_CS0_SIZE		(256 * 1024 * 1024)
+
+/*
+ * Hardware drivers
+ */
+
+/*
+ * NS16550 Configuration
+ */
+#define V_NS16550_CLK			48000000	/* 48MHz (APLL96/2) */
+
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
+#define CONFIG_SYS_NS16550_CLK		V_NS16550_CLK
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_CONS_INDEX		3
+#define CONFIG_SYS_NS16550_COM3		OMAP34XX_UART3
+#define CONFIG_SERIAL3			3	/* UART3 */
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{4800, 9600, 19200, 38400, 57600,\
+					115200}
+#define CONFIG_MMC
+#define CONFIG_OMAP_HSMMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_DOS_PARTITION
+
+/* commands to include */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_EXT2		/* EXT2 Support			*/
+#define CONFIG_CMD_FAT		/* FAT support			*/
+#define CONFIG_CMD_JFFS2	/* JFFS2 Support		*/
+
+#define CONFIG_CMD_I2C		/* I2C serial bus support	*/
+#define CONFIG_CMD_MMC		/* MMC support			*/
+#define CONFIG_CMD_FAT		/* FAT support			*/
+#define CONFIG_CMD_NAND		/* NAND support			*/
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+
+#undef CONFIG_CMD_FLASH		/* flinfo, erase, protect	*/
+#undef CONFIG_CMD_FPGA		/* FPGA configuration Support	*/
+#undef CONFIG_CMD_IMI		/* iminfo			*/
+#undef CONFIG_CMD_IMLS		/* List all found images	*/
+
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_HARD_I2C
+#define CONFIG_SYS_I2C_SPEED		100000
+#define CONFIG_SYS_I2C_SLAVE		1
+#define CONFIG_SYS_I2C_BUS		0
+#define CONFIG_DRIVER_OMAP34XX_I2C
+
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NFS
+/*
+ * Board NAND Info.
+ */
+#define CONFIG_SYS_NAND_ADDR		NAND_BASE	/* physical address */
+							/* to access nand */
+#define CONFIG_SYS_NAND_BASE		NAND_BASE	/* physical address */
+							/* to access */
+							/* nand at CS0 */
+
+#define CONFIG_SYS_MAX_NAND_DEVICE	1		/* Max number of */
+							/* NAND devices */
+#define CONFIG_SYS_64BIT_VSPRINTF		/* needed for nand_util.c */
+
+#define CONFIG_JFFS2_NAND
+/* nand device jffs2 lives on */
+#define CONFIG_JFFS2_DEV		"nand0"
+/* start of jffs2 partition */
+#define CONFIG_JFFS2_PART_OFFSET	0x680000
+#define CONFIG_JFFS2_PART_SIZE		0xf980000	/* sz of jffs2 part */
+
+/* Environment information */
+#define CONFIG_BOOTDELAY	10
+
+#define CONFIG_BOOTFILE		uImage
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"loadaddr=0x82000000\0" \
+	"console=ttyO2,115200n8\0" \
+	"mmcargs=setenv bootargs console=${console} " \
+		"root=/dev/mmcblk0p2 rw " \
+		"rootfstype=ext3 rootwait\0" \
+	"nandargs=setenv bootargs console=${console} " \
+		"root=/dev/mtdblock4 rw " \
+		"rootfstype=jffs2\0" \
+	"loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
+	"bootscript=echo Running bootscript from mmc ...; " \
+		"source ${loadaddr}\0" \
+	"loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; " \
+		"bootm ${loadaddr}\0" \
+	"nandboot=echo Booting from nand ...; " \
+		"run nandargs; " \
+		"nand read ${loadaddr} 280000 400000; " \
+		"bootm ${loadaddr}\0" \
+
+#define CONFIG_BOOTCOMMAND \
+	"if mmc init; then " \
+		"if run loadbootscript; then " \
+			"run bootscript; " \
+		"else " \
+			"if run loaduimage; then " \
+				"run mmcboot; " \
+			"else run nandboot; " \
+			"fi; " \
+		"fi; " \
+	"else run nandboot; fi"
+
+#define CONFIG_AUTO_COMPLETE
+/*
+ * Miscellaneous configurable options
+ */
+#define V_PROMPT			"mcx # "
+
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser */
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+#define CONFIG_SYS_PROMPT		V_PROMPT
+#define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
+					sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS		32	/* max number of command */
+						/* args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE		(CONFIG_SYS_CBSIZE)
+/* memtest works on */
+#define CONFIG_SYS_MEMTEST_START	(OMAP34XX_SDRC_CS0)
+#define CONFIG_SYS_MEMTEST_END		(OMAP34XX_SDRC_CS0 + \
+					0x01F00000) /* 31MB */
+
+#define CONFIG_SYS_LOAD_ADDR		(OMAP34XX_SDRC_CS0) /* default load */
+								/* address */
+
+/*
+ * AM3517 has 12 GP timers, they can be driven by the system clock
+ * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
+ * This rate is divided by a local divisor.
+ */
+#define CONFIG_SYS_TIMERBASE		OMAP34XX_GPT2
+#define CONFIG_SYS_PTV			2	/* Divisor: 2^(PTV+1) => 8 */
+#define CONFIG_SYS_HZ			1000
+
+/*-----------------------------------------------------------------------
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE	(128 << 10)	/* regular stack 128 KiB */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ	(4 << 10)	/* IRQ stack 4 KiB */
+#define CONFIG_STACKSIZE_FIQ	(4 << 10)	/* FIQ stack 4 KiB */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS	2	/* CS1 may or may not be populated */
+#define PHYS_SDRAM_1		OMAP34XX_SDRC_CS0
+#define PHYS_SDRAM_1_SIZE	(32 << 20)	/* at least 32 MiB */
+#define PHYS_SDRAM_2		OMAP34XX_SDRC_CS1
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+
+/* **** PISMO SUPPORT *** */
+
+/* Configure the PISMO */
+#define PISMO1_NAND_SIZE		GPMC_SIZE_128M
+#define PISMO1_ONEN_SIZE		GPMC_SIZE_128M
+
+#define CONFIG_SYS_MAX_FLASH_SECT	520	/* max number of sectors */
+						/* on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of flash banks */
+#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 2 sectors */
+
+#if defined(CONFIG_CMD_NAND)
+#define CONFIG_SYS_FLASH_BASE		PISMO1_NAND_BASE
+#endif
+
+/* Monitor@start of flash */
+#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
+
+#define CONFIG_NAND_OMAP_GPMC
+#define GPMC_NAND_ECC_LP_x16_LAYOUT
+#define CONFIG_ENV_IS_IN_NAND
+#define SMNAND_ENV_OFFSET		0x260000 /* environment starts here */
+
+#define CONFIG_SYS_ENV_SECT_SIZE	(128 << 10)	/* 128 KiB */
+#define CONFIG_ENV_OFFSET		SMNAND_ENV_OFFSET
+#define CONFIG_ENV_ADDR			SMNAND_ENV_OFFSET
+
+/*-----------------------------------------------------------------------
+ * CFI FLASH driver setup
+ */
+/* timeout values are in ticks */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	(100 * CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT	(100 * CONFIG_SYS_HZ)
+
+/* Flash banks JFFS2 should use */
+#define CONFIG_SYS_MAX_MTD_BANKS	(CONFIG_SYS_MAX_FLASH_BANKS + \
+					CONFIG_SYS_MAX_NAND_DEVICE)
+#define CONFIG_SYS_JFFS2_MEM_NAND
+/* use flash_info[2] */
+#define CONFIG_SYS_JFFS2_FIRST_BANK	CONFIG_SYS_MAX_FLASH_BANKS
+#define CONFIG_SYS_JFFS2_NUM_BANKS	1
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_ADDR	0x4020f800
+#define CONFIG_SYS_INIT_RAM_SIZE	0x800
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
+					 CONFIG_SYS_INIT_RAM_SIZE - \
+					 GENERATED_GBL_DATA_SIZE)
+
+/*
+ * ethernet support
+ *
+ */
+#if defined(CONFIG_CMD_NET)
+#define CONFIG_DRIVER_TI_EMAC
+#define CONFIG_DRIVER_TI_EMAC_USE_RMII
+#define CONFIG_MII
+#define CONFIG_EMAC_MDIO_PHY_NUM	0
+#define	CONFIG_BOOTP_DEFAULT
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_NET_RETRY_COUNT 10
+#endif
+
+#endif /* __CONFIG_H */
-- 
1.7.6.2

[U-Boot] [PATCH 6/8] AM35xx: add EMAC support

[Mike Frysinger]

On Thursday 13 October 2011 17:11:50 Ilya Yanok wrote:
> --- /dev/null
> +++ b/arch/arm/cpu/armv7/omap3/emac.c
>
> +/*
> + * Initializes on-chip ethernet controllers.
> + * to override, implement board_eth_init()
> + */
> +int cpu_eth_init(bd_t *bis)
> +{
> +	davinci_emac_initialize();
> +
> +	return 0;
> +}

shouldn't emac support always be up to the board porter and not the SoC code ?  
also, this should be:
int cpu_eth_init(bd_t *bis)
{
	return davinci_emac_initialize();
}
-mike
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: This is a digitally signed message part.
Url : http://lists.denx.de/pipermail/u-boot/attachments/20111013/02c93de5/attachment.pgp 

[U-Boot] [PATCH 8/8] mcx: support for HTKW mcx board

[Mike Frysinger]

On Thursday 13 October 2011 17:11:52 Ilya Yanok wrote:
> --- /dev/null
> +++ b/board/htkw/mcx/Makefile
>
> +clean:
> +	rm -f $(OBJS)
> +
> +distclean:	clean
> +	rm -f $(LIB) core *.bak $(obj).depend

dead code; please drop
-mike
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: This is a digitally signed message part.
Url : http://lists.denx.de/pipermail/u-boot/attachments/20111013/a9a3f7c9/attachment.pgp 

[U-Boot] [PATCH 1/8] davinci_emac: move arch-independent defines to separate header

[Mike Frysinger]

On Thursday 13 October 2011 17:11:45 Ilya Yanok wrote:
> DaVinci EMAC is found not only on DaVinci SoCs but on some OMAP3 SoCs
> also. This patch moves common defines from arch-davinci/emac_defs.h to
> drivers/net/davinci_emac.h

nice work !
-mike
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: This is a digitally signed message part.
Url : http://lists.denx.de/pipermail/u-boot/attachments/20111013/9d8432e3/attachment.pgp 

[U-Boot] [PATCH 6/8] AM35xx: add EMAC support

[Ilya Yanok]

Hi Mike,

On 14.10.2011 02:55, Mike Frysinger wrote:
>> --- /dev/null
>> +++ b/arch/arm/cpu/armv7/omap3/emac.c
>>
>> +/*
>> + * Initializes on-chip ethernet controllers.
>> + * to override, implement board_eth_init()
>> + */
>> +int cpu_eth_init(bd_t *bis)
>> +{
>> +	davinci_emac_initialize();
>> +
>> +	return 0;
>> +}
> 
> shouldn't emac support always be up to the board porter and not the SoC code ?  

It's up to the board porter to define CONFIG_DRIVER_TI_EMAC (or not),
isn't it enough?

> also, this should be:
> int cpu_eth_init(bd_t *bis)
> {
> 	return davinci_emac_initialize();
> }

Agreed.

Regards, Ilya.

[U-Boot] [PATCH 6/8] AM35xx: add EMAC support

[Igor Grinberg]

On 10/14/11 09:51, Ilya Yanok wrote:
> Hi Mike,
> 
> On 14.10.2011 02:55, Mike Frysinger wrote:
>>> --- /dev/null
>>> +++ b/arch/arm/cpu/armv7/omap3/emac.c
>>>
>>> +/*
>>> + * Initializes on-chip ethernet controllers.
>>> + * to override, implement board_eth_init()
>>> + */
>>> +int cpu_eth_init(bd_t *bis)
>>> +{
>>> +	davinci_emac_initialize();
>>> +
>>> +	return 0;
>>> +}
>>
>> shouldn't emac support always be up to the board porter and not the SoC code ?  
> 
> It's up to the board porter to define CONFIG_DRIVER_TI_EMAC (or not),
> isn't it enough?

Yes, it should be enough, especially in case of EMAC on Davinci and AM35x,
when this IP block is always present inside the SoC.

> 
>> also, this should be:
>> int cpu_eth_init(bd_t *bis)
>> {
>> 	return davinci_emac_initialize();
>> }
> 
> Agreed.
> 
> Regards, Ilya.
> 
> 
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
> 

-- 
Regards,
Igor.

[U-Boot] [PATCH 7/8] AM3517: move AM3517 specific mux defines to generic header

[Igor Grinberg]

On 10/13/11 23:11, Ilya Yanok wrote:
> AM3517 specific CONTROL_PADCONF_* defines moved from board-specific
> files to <asm/arch-omap3/mux.h>

Thanks, this is something I wanted to do a long time before,
but had no time to get my hands on...

> 
> Signed-off-by: Ilya Yanok <yanok@emcraft.com>

Acked-by: Igor Grinberg <grinberg@compulab.co.il>

> ---
>  arch/arm/include/asm/arch-omap3/mux.h |   41 +++++++++++++++++++++++++++++++++
>  board/logicpd/am3517evm/am3517evm.h   |   40 --------------------------------
>  board/ti/am3517crane/am3517crane.h    |   39 -------------------------------
>  3 files changed, 41 insertions(+), 79 deletions(-)
> 
> diff --git a/arch/arm/include/asm/arch-omap3/mux.h b/arch/arm/include/asm/arch-omap3/mux.h
> index 0c01c73..6daef49 100644
> --- a/arch/arm/include/asm/arch-omap3/mux.h
> +++ b/arch/arm/include/asm/arch-omap3/mux.h
> @@ -404,6 +404,47 @@
>  #define CONTROL_PADCONF_SDRC_CKE0	0x0262
>  #define CONTROL_PADCONF_SDRC_CKE1	0x0264
>  
> +/* AM3517 specific mux configuration */
> +#define CONTROL_PADCONF_SYS_NRESWARM	0x0A08
> +/* CCDC */
> +#define CONTROL_PADCONF_CCDC_PCLK	0x01E4
> +#define CONTROL_PADCONF_CCDC_FIELD	0x01E6
> +#define CONTROL_PADCONF_CCDC_HD		0x01E8
> +#define CONTROL_PADCONF_CCDC_VD		0x01EA
> +#define CONTROL_PADCONF_CCDC_WEN	0x01EC
> +#define CONTROL_PADCONF_CCDC_DATA0	0x01EE
> +#define CONTROL_PADCONF_CCDC_DATA1	0x01F0
> +#define CONTROL_PADCONF_CCDC_DATA2	0x01F2
> +#define CONTROL_PADCONF_CCDC_DATA3	0x01F4
> +#define CONTROL_PADCONF_CCDC_DATA4	0x01F6
> +#define CONTROL_PADCONF_CCDC_DATA5	0x01F8
> +#define CONTROL_PADCONF_CCDC_DATA6	0x01FA
> +#define CONTROL_PADCONF_CCDC_DATA7	0x01FC
> +/* RMII */
> +#define CONTROL_PADCONF_RMII_MDIO_DATA	0x01FE
> +#define CONTROL_PADCONF_RMII_MDIO_CLK	0x0200
> +#define CONTROL_PADCONF_RMII_RXD0	0x0202
> +#define CONTROL_PADCONF_RMII_RXD1	0x0204
> +#define CONTROL_PADCONF_RMII_CRS_DV	0x0206
> +#define CONTROL_PADCONF_RMII_RXER	0x0208
> +#define CONTROL_PADCONF_RMII_TXD0	0x020A
> +#define CONTROL_PADCONF_RMII_TXD1	0x020C
> +#define CONTROL_PADCONF_RMII_TXEN	0x020E
> +#define CONTROL_PADCONF_RMII_50MHZ_CLK	0x0210
> +#define CONTROL_PADCONF_USB0_DRVBUS	0x0212
> +/* CAN */
> +#define CONTROL_PADCONF_HECC1_TXD	0x0214
> +#define CONTROL_PADCONF_HECC1_RXD	0x0216
> +
> +#define CONTROL_PADCONF_SYS_BOOT7	0x0218
> +#define CONTROL_PADCONF_SDRC_DQS0N	0x021A
> +#define CONTROL_PADCONF_SDRC_DQS1N	0x021C
> +#define CONTROL_PADCONF_SDRC_DQS2N	0x021E
> +#define CONTROL_PADCONF_SDRC_DQS3N	0x0220
> +#define CONTROL_PADCONF_STRBEN_DLY0	0x0222
> +#define CONTROL_PADCONF_STRBEN_DLY1	0x0224
> +#define CONTROL_PADCONF_SYS_BOOT8	0x0226
> +
>  #define MUX_VAL(OFFSET,VALUE)\
>  	writew((VALUE), OMAP34XX_CTRL_BASE + (OFFSET));
>  
> diff --git a/board/logicpd/am3517evm/am3517evm.h b/board/logicpd/am3517evm/am3517evm.h
> index 3d74ef1..68d746c 100644
> --- a/board/logicpd/am3517evm/am3517evm.h
> +++ b/board/logicpd/am3517evm/am3517evm.h
> @@ -31,46 +31,6 @@ const omap3_sysinfo sysinfo = {
>  	"AM3517EVM Board",
>  	"NAND",
>  };
> -/* AM3517 specific mux configuration */
> -#define CONTROL_PADCONF_SYS_NRESWARM	0x0A08
> -/* CCDC */
> -#define CONTROL_PADCONF_CCDC_PCLK	0x01E4
> -#define CONTROL_PADCONF_CCDC_FIELD	0x01E6
> -#define CONTROL_PADCONF_CCDC_HD		0x01E8
> -#define CONTROL_PADCONF_CCDC_VD		0x01EA
> -#define CONTROL_PADCONF_CCDC_WEN	0x01EC
> -#define CONTROL_PADCONF_CCDC_DATA0	0x01EE
> -#define CONTROL_PADCONF_CCDC_DATA1	0x01F0
> -#define CONTROL_PADCONF_CCDC_DATA2	0x01F2
> -#define CONTROL_PADCONF_CCDC_DATA3	0x01F4
> -#define CONTROL_PADCONF_CCDC_DATA4	0x01F6
> -#define CONTROL_PADCONF_CCDC_DATA5	0x01F8
> -#define CONTROL_PADCONF_CCDC_DATA6	0x01FA
> -#define CONTROL_PADCONF_CCDC_DATA7	0x01FC
> -/* RMII */
> -#define CONTROL_PADCONF_RMII_MDIO_DATA	0x01FE
> -#define CONTROL_PADCONF_RMII_MDIO_CLK	0x0200
> -#define CONTROL_PADCONF_RMII_RXD0	0x0202
> -#define CONTROL_PADCONF_RMII_RXD1	0x0204
> -#define CONTROL_PADCONF_RMII_CRS_DV	0x0206
> -#define CONTROL_PADCONF_RMII_RXER	0x0208
> -#define CONTROL_PADCONF_RMII_TXD0	0x020A
> -#define CONTROL_PADCONF_RMII_TXD1	0x020C
> -#define CONTROL_PADCONF_RMII_TXEN	0x020E
> -#define CONTROL_PADCONF_RMII_50MHZ_CLK	0x0210
> -#define CONTROL_PADCONF_USB0_DRVBUS	0x0212
> -/* CAN */
> -#define CONTROL_PADCONF_HECC1_TXD	0x0214
> -#define CONTROL_PADCONF_HECC1_RXD	0x0216
> -
> -#define CONTROL_PADCONF_SYS_BOOT7	0x0218
> -#define CONTROL_PADCONF_SDRC_DQS0N	0x021A
> -#define CONTROL_PADCONF_SDRC_DQS1N	0x021C
> -#define CONTROL_PADCONF_SDRC_DQS2N	0x021E
> -#define CONTROL_PADCONF_SDRC_DQS3N	0x0220
> -#define CONTROL_PADCONF_STRBEN_DLY0	0x0222
> -#define CONTROL_PADCONF_STRBEN_DLY1	0x0224
> -#define CONTROL_PADCONF_SYS_BOOT8	0x0226
>  
>  /*
>   * IEN  - Input Enable
> diff --git a/board/ti/am3517crane/am3517crane.h b/board/ti/am3517crane/am3517crane.h
> index 41db972..71335a3 100644
> --- a/board/ti/am3517crane/am3517crane.h
> +++ b/board/ti/am3517crane/am3517crane.h
> @@ -30,45 +30,6 @@ const omap3_sysinfo sysinfo = {
>  	"CraneBoard",
>  	"NAND",
>  };
> -/* AM3517 specific mux configuration */
> -#define CONTROL_PADCONF_SYS_NRESWARM	0x0A08
> -/* CCDC */
> -#define CONTROL_PADCONF_CCDC_PCLK	0x01E4
> -#define CONTROL_PADCONF_CCDC_FIELD	0x01E6
> -#define CONTROL_PADCONF_CCDC_HD		0x01E8
> -#define CONTROL_PADCONF_CCDC_VD		0x01EA
> -#define CONTROL_PADCONF_CCDC_WEN	0x01EC
> -#define CONTROL_PADCONF_CCDC_DATA0	0x01EE
> -#define CONTROL_PADCONF_CCDC_DATA1	0x01F0
> -#define CONTROL_PADCONF_CCDC_DATA2	0x01F2
> -#define CONTROL_PADCONF_CCDC_DATA3	0x01F4
> -#define CONTROL_PADCONF_CCDC_DATA4	0x01F6
> -#define CONTROL_PADCONF_CCDC_DATA5	0x01F8
> -#define CONTROL_PADCONF_CCDC_DATA6	0x01FA
> -#define CONTROL_PADCONF_CCDC_DATA7	0x01FC
> -/* RMII */
> -#define CONTROL_PADCONF_RMII_MDIO_DATA	0x01FE
> -#define CONTROL_PADCONF_RMII_MDIO_CLK	0x0200
> -#define CONTROL_PADCONF_RMII_RXD0	0x0202
> -#define CONTROL_PADCONF_RMII_RXD1	0x0204
> -#define CONTROL_PADCONF_RMII_CRS_DV	0x0206
> -#define CONTROL_PADCONF_RMII_RXER	0x0208
> -#define CONTROL_PADCONF_RMII_TXD0	0x020A
> -#define CONTROL_PADCONF_RMII_TXD1	0x020C
> -#define CONTROL_PADCONF_RMII_TXEN	0x020E
> -#define CONTROL_PADCONF_RMII_50MHZ_CLK	0x0210
> -#define CONTROL_PADCONF_USB0_DRVBUS	0x0212
> -/* CAN */
> -#define CONTROL_PADCONF_HECC1_TXD	0x0214
> -#define CONTROL_PADCONF_HECC1_RXD	0x0216
> -#define CONTROL_PADCONF_SYS_BOOT7	0x0218
> -#define CONTROL_PADCONF_SDRC_DQS0N	0x021A
> -#define CONTROL_PADCONF_SDRC_DQS1N	0x021C
> -#define CONTROL_PADCONF_SDRC_DQS2N	0x021E
> -#define CONTROL_PADCONF_SDRC_DQS3N	0x0220
> -#define CONTROL_PADCONF_STRBEN_DLY0	0x0222
> -#define CONTROL_PADCONF_STRBEN_DLY1	0x0224
> -#define CONTROL_PADCONF_SYS_BOOT8	0x0226
>  
>  /*
>   * IEN  - Input Enable

-- 
Regards,
Igor.

[U-Boot] [PATCH 8/8] mcx: support for HTKW mcx board

[Igor Grinberg]

Hi Ilya,

On 10/13/11 23:11, Ilya Yanok wrote:
> This patch adds support for the HTKW mcx AM3517-based board.
> Serial, Ethernet, NAND and MMC are supported.
> 
> Requires updated mach-types file.
> 
> Signed-off-by: Ilya Yanok <yanok@emcraft.com>
> ---

[...]

> diff --git a/board/htkw/mcx/mcx.c b/board/htkw/mcx/mcx.c
> new file mode 100644
> index 0000000..00bd564
> --- /dev/null
> +++ b/board/htkw/mcx/mcx.c

[...]

> +
> +#define AM3517_IP_SW_RESET	0x48002598
> +#define CPGMACSS_SW_RST		(1 << 1)

[...]

> +int misc_init_r(void)
> +{
> +#if defined(CONFIG_DRIVER_TI_EMAC)
> +	u32 reset;
> +#endif
> +
> +	dieid_num_r();
> +
> +#if defined(CONFIG_DRIVER_TI_EMAC)
> +	/* ensure that the module is out of reset */
> +	reset = readl(AM3517_IP_SW_RESET);
> +	reset &= ~CPGMACSS_SW_RST;
> +	writel(reset, AM3517_IP_SW_RESET);
> +
> +#endif
> +	return 0;
> +}

I don't really insist, but couldn't the EMAC reset be handled
in the cpu_eth_init() function, instead of each board does
the reset itself?

[...]


-- 
Regards,
Igor.

[U-Boot] [PATCH] AM35xx: add EMAC support

[Ilya Yanok]

AM35xx has DaVinci-compatible EMAC.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---
 arch/arm/cpu/armv7/omap3/Makefile           |    1 +
 arch/arm/cpu/armv7/omap3/emac.c             |   44 +++++++++++++++++++++
 arch/arm/include/asm/arch-omap3/am35x_def.h |    3 +
 arch/arm/include/asm/arch-omap3/emac_defs.h |   56 +++++++++++++++++++++++++++
 4 files changed, 104 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/cpu/armv7/omap3/emac.c
 create mode 100644 arch/arm/include/asm/arch-omap3/emac_defs.h

diff --git a/arch/arm/cpu/armv7/omap3/Makefile b/arch/arm/cpu/armv7/omap3/Makefile
index 8e85891..6ebfd32 100644
--- a/arch/arm/cpu/armv7/omap3/Makefile
+++ b/arch/arm/cpu/armv7/omap3/Makefile
@@ -32,6 +32,7 @@ COBJS	+= clock.o
 COBJS	+= mem.o
 COBJS	+= sys_info.o
 
+COBJS-$(CONFIG_DRIVER_TI_EMAC)	+= emac.o
 COBJS-$(CONFIG_EMIF4)	+= emif4.o
 COBJS-$(CONFIG_SDRC)	+= sdrc.o
 
diff --git a/arch/arm/cpu/armv7/omap3/emac.c b/arch/arm/cpu/armv7/omap3/emac.c
new file mode 100644
index 0000000..14667f1
--- /dev/null
+++ b/arch/arm/cpu/armv7/omap3/emac.c
@@ -0,0 +1,44 @@
+/*
+ *
+ * DaVinci EMAC initialization.
+ *
+ * (C) Copyright 2011, Ilya Yanok, Emcraft Systems
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc.
+ */
+
+#include <common.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/arch/am35x_def.h>
+
+/*
+ * Initializes on-chip ethernet controllers.
+ * to override, implement board_eth_init()
+ */
+int cpu_eth_init(bd_t *bis)
+{
+	u32 reset;
+
+	/* ensure that the module is out of reset */
+	reset = readl(&am35x_scm_general_regs->ip_sw_reset);
+	reset &= ~CPGMACSS_SW_RST;
+	writel(reset, &am35x_scm_general_regs->ip_sw_reset);
+
+	return davinci_emac_initialize();
+}
diff --git a/arch/arm/include/asm/arch-omap3/am35x_def.h b/arch/arm/include/asm/arch-omap3/am35x_def.h
index 81942a8..bbaf1bc 100644
--- a/arch/arm/include/asm/arch-omap3/am35x_def.h
+++ b/arch/arm/include/asm/arch-omap3/am35x_def.h
@@ -32,6 +32,9 @@
 #ifndef __KERNEL_STRICT_NAMES
 #ifndef __ASSEMBLY__
 
+/* IP_SW_RESET bits */
+#define CPGMACSS_SW_RST		(1 << 1)	/* reset CPGMAC */
+
 /* General register mappings of system control module */
 #define AM35X_SCM_GEN_BASE	0x48002270
 struct am35x_scm_general {
diff --git a/arch/arm/include/asm/arch-omap3/emac_defs.h b/arch/arm/include/asm/arch-omap3/emac_defs.h
new file mode 100644
index 0000000..8506c55
--- /dev/null
+++ b/arch/arm/include/asm/arch-omap3/emac_defs.h
@@ -0,0 +1,56 @@
+/*
+ * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
+ *
+ * Based on:
+ *
+ * ----------------------------------------------------------------------------
+ *
+ * dm644x_emac.h
+ *
+ * TI DaVinci (DM644X) EMAC peripheral driver header for DV-EVM
+ *
+ * Copyright (C) 2005 Texas Instruments.
+ *
+ * ----------------------------------------------------------------------------
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, write to the Free Software
+ *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ * ----------------------------------------------------------------------------
+
+ * Modifications:
+ * ver. 1.0: Sep 2005, TI PSP Team - Created EMAC version for uBoot.
+ *
+ */
+
+#ifndef _AM3517_EMAC_H_
+#define _AM3517_EMAC_H_
+
+#define EMAC_BASE_ADDR                 0x5C010000
+#define EMAC_WRAPPER_BASE_ADDR         0x5C000000
+#define EMAC_WRAPPER_RAM_ADDR          0x5C020000
+#define EMAC_MDIO_BASE_ADDR            0x5C030000
+#define EMAC_HW_RAM_ADDR               0x01E20000
+
+#define EMAC_MDIO_BUS_FREQ             166000000       /* 166 MHZ check */
+#define EMAC_MDIO_CLOCK_FREQ           1000000         /* 2.0 MHz */
+
+/* SOFTRESET macro definition interferes with emac_regs structure definition */
+#undef SOFTRESET
+
+typedef volatile unsigned int	dv_reg;
+typedef volatile unsigned int	*dv_reg_p;
+
+#define DAVINCI_EMAC_VERSION2
+
+#endif  /* _AM3517_EMAC_H_ */
-- 
1.7.6.4

[U-Boot] [PATCH] AM35xx: add EMAC support

[Ilya Yanok]

On 18.10.2011 02:25, Ilya Yanok wrote:
> AM35xx has DaVinci-compatible EMAC.

Argh.. Sorry, replied to the wrong message.

Regards, Ilya.

[U-Boot] [PATCH 6/8][v3] AM35xx: add EMAC support

[Ilya Yanok]

AM35xx has DaVinci-compatible EMAC.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---

Diff from v2:
 1. Fixed the return value as Mike suggested.
 2. Moved EMAC reset from board file to cpu_eth_init() as Igor suggested.

 arch/arm/cpu/armv7/omap3/Makefile           |    1 +
 arch/arm/cpu/armv7/omap3/emac.c             |   44 +++++++++++++++++++++
 arch/arm/include/asm/arch-omap3/am35x_def.h |    3 +
 arch/arm/include/asm/arch-omap3/emac_defs.h |   56 +++++++++++++++++++++++++++
 4 files changed, 104 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/cpu/armv7/omap3/emac.c
 create mode 100644 arch/arm/include/asm/arch-omap3/emac_defs.h

diff --git a/arch/arm/cpu/armv7/omap3/Makefile b/arch/arm/cpu/armv7/omap3/Makefile
index 8e85891..6ebfd32 100644
--- a/arch/arm/cpu/armv7/omap3/Makefile
+++ b/arch/arm/cpu/armv7/omap3/Makefile
@@ -32,6 +32,7 @@ COBJS	+= clock.o
 COBJS	+= mem.o
 COBJS	+= sys_info.o
 
+COBJS-$(CONFIG_DRIVER_TI_EMAC)	+= emac.o
 COBJS-$(CONFIG_EMIF4)	+= emif4.o
 COBJS-$(CONFIG_SDRC)	+= sdrc.o
 
diff --git a/arch/arm/cpu/armv7/omap3/emac.c b/arch/arm/cpu/armv7/omap3/emac.c
new file mode 100644
index 0000000..14667f1
--- /dev/null
+++ b/arch/arm/cpu/armv7/omap3/emac.c
@@ -0,0 +1,44 @@
+/*
+ *
+ * DaVinci EMAC initialization.
+ *
+ * (C) Copyright 2011, Ilya Yanok, Emcraft Systems
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc.
+ */
+
+#include <common.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/arch/am35x_def.h>
+
+/*
+ * Initializes on-chip ethernet controllers.
+ * to override, implement board_eth_init()
+ */
+int cpu_eth_init(bd_t *bis)
+{
+	u32 reset;
+
+	/* ensure that the module is out of reset */
+	reset = readl(&am35x_scm_general_regs->ip_sw_reset);
+	reset &= ~CPGMACSS_SW_RST;
+	writel(reset, &am35x_scm_general_regs->ip_sw_reset);
+
+	return davinci_emac_initialize();
+}
diff --git a/arch/arm/include/asm/arch-omap3/am35x_def.h b/arch/arm/include/asm/arch-omap3/am35x_def.h
index 81942a8..bbaf1bc 100644
--- a/arch/arm/include/asm/arch-omap3/am35x_def.h
+++ b/arch/arm/include/asm/arch-omap3/am35x_def.h
@@ -32,6 +32,9 @@
 #ifndef __KERNEL_STRICT_NAMES
 #ifndef __ASSEMBLY__
 
+/* IP_SW_RESET bits */
+#define CPGMACSS_SW_RST		(1 << 1)	/* reset CPGMAC */
+
 /* General register mappings of system control module */
 #define AM35X_SCM_GEN_BASE	0x48002270
 struct am35x_scm_general {
diff --git a/arch/arm/include/asm/arch-omap3/emac_defs.h b/arch/arm/include/asm/arch-omap3/emac_defs.h
new file mode 100644
index 0000000..8506c55
--- /dev/null
+++ b/arch/arm/include/asm/arch-omap3/emac_defs.h
@@ -0,0 +1,56 @@
+/*
+ * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
+ *
+ * Based on:
+ *
+ * ----------------------------------------------------------------------------
+ *
+ * dm644x_emac.h
+ *
+ * TI DaVinci (DM644X) EMAC peripheral driver header for DV-EVM
+ *
+ * Copyright (C) 2005 Texas Instruments.
+ *
+ * ----------------------------------------------------------------------------
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, write to the Free Software
+ *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ * ----------------------------------------------------------------------------
+
+ * Modifications:
+ * ver. 1.0: Sep 2005, TI PSP Team - Created EMAC version for uBoot.
+ *
+ */
+
+#ifndef _AM3517_EMAC_H_
+#define _AM3517_EMAC_H_
+
+#define EMAC_BASE_ADDR                 0x5C010000
+#define EMAC_WRAPPER_BASE_ADDR         0x5C000000
+#define EMAC_WRAPPER_RAM_ADDR          0x5C020000
+#define EMAC_MDIO_BASE_ADDR            0x5C030000
+#define EMAC_HW_RAM_ADDR               0x01E20000
+
+#define EMAC_MDIO_BUS_FREQ             166000000       /* 166 MHZ check */
+#define EMAC_MDIO_CLOCK_FREQ           1000000         /* 2.0 MHz */
+
+/* SOFTRESET macro definition interferes with emac_regs structure definition */
+#undef SOFTRESET
+
+typedef volatile unsigned int	dv_reg;
+typedef volatile unsigned int	*dv_reg_p;
+
+#define DAVINCI_EMAC_VERSION2
+
+#endif  /* _AM3517_EMAC_H_ */
-- 
1.7.6.4

[U-Boot] [PATCH 8/8] mcx: support for HTKW mcx board

[Ilya Yanok]

Hi Igor,

On 16.10.2011 12:42, Igor Grinberg wrote:
> I don't really insist, but couldn't the EMAC reset be handled
> in the cpu_eth_init() function, instead of each board does
> the reset itself?

Thanks for review! I've done as you suggest in my v3 patch.

Regards, Ilya.

[U-Boot] [PATCH 8/8][v3] mcx: support for HTKW mcx board

[Ilya Yanok]

This patch adds support for the HTKW mcx AM3517-based board.
Serial, Ethernet, NAND and MMC are supported.

Requires updated mach-types file.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
---

Diff from v2:
 1. removed dead code from board/htkw/mcx/Makefile as Mike suggested
 2. removed EMAC reset (now done in generic cpu_eth_init())
 3. removed some unsuned defines from configuration header

 MAINTAINERS             |    4 +
 board/htkw/mcx/Makefile |   38 +++++
 board/htkw/mcx/mcx.c    |   75 +++++++++
 board/htkw/mcx/mcx.h    |  408 +++++++++++++++++++++++++++++++++++++++++++++++
 boards.cfg              |    1 +
 include/configs/mcx.h   |  302 +++++++++++++++++++++++++++++++++++
 6 files changed, 828 insertions(+), 0 deletions(-)
 create mode 100644 board/htkw/mcx/Makefile
 create mode 100644 board/htkw/mcx/mcx.c
 create mode 100644 board/htkw/mcx/mcx.h
 create mode 100644 include/configs/mcx.h

diff --git a/MAINTAINERS b/MAINTAINERS
index bb95e6d..c09e19a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -878,6 +878,10 @@ Richard Woodruff <r-woodruff2@ti.com>
 
 	omap2420h4	ARM1136EJS
 
+Ilya Yanok <yanok@emcraft.com>
+
+	mcx		ARM ARMV7 (AM35x SoC)
+
 Syed Mohammed Khasim <sm.khasim@gmail.com>
 Sughosh Ganu <urwithsughosh@gmail.com>
 
diff --git a/board/htkw/mcx/Makefile b/board/htkw/mcx/Makefile
new file mode 100644
index 0000000..4c8db10
--- /dev/null
+++ b/board/htkw/mcx/Makefile
@@ -0,0 +1,38 @@
+#
+# Copyright (C) 2011 Ilya Yanok, Emcraft Systems
+#
+# Based on ti/evm/Makefile
+#
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation; either version 2 of the License, or
+# (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc.
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS	:= $(BOARD).o
+
+SRCS	:= $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
diff --git a/board/htkw/mcx/mcx.c b/board/htkw/mcx/mcx.c
new file mode 100644
index 0000000..494065e
--- /dev/null
+++ b/board/htkw/mcx/mcx.c
@@ -0,0 +1,75 @@
+/*
+ * Copyright (C) 2011 Ilya Yanok, Emcraft Systems
+ *
+ * Based on ti/evm/evm.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc.
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-types.h>
+#include <asm/omap_gpio.h>
+#include <i2c.h>
+#include "mcx.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Routine: board_init
+ * Description: Early hardware init.
+ */
+int board_init(void)
+{
+	gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
+	/* boot param addr */
+	gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
+
+	return 0;
+}
+
+/*
+ * Routine: misc_init_r
+ * Description: Init i2c, ethernet, etc... (done here so udelay works)
+ */
+int misc_init_r(void)
+{
+	dieid_num_r();
+
+	return 0;
+}
+
+/*
+ * Routine: set_muxconf_regs
+ * Description: Setting up the configuration Mux registers specific to the
+ *		hardware. Many pins need to be moved from protect to primary
+ *		mode.
+ */
+void set_muxconf_regs(void)
+{
+	MUX_MCX();
+}
+
+#if defined(CONFIG_GENERIC_MMC) && defined(CONFIG_OMAP_HSMMC)
+int board_mmc_init(bd_t *bis)
+{
+	omap_mmc_init(0);
+	return 0;
+}
+#endif
diff --git a/board/htkw/mcx/mcx.h b/board/htkw/mcx/mcx.h
new file mode 100644
index 0000000..d675a48
--- /dev/null
+++ b/board/htkw/mcx/mcx.h
@@ -0,0 +1,408 @@
+/*
+ * Copyright (C) 2011 Ilya Yanok, Emcraft Systems
+ *
+ * Based on ti/evm/evm.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc.
+ */
+
+#ifndef _AM3517EVM_H_
+#define _AM3517EVM_H_
+
+const omap3_sysinfo sysinfo = {
+	DDR_DISCRETE,
+	"HTKW mcx Board",
+	"NAND",
+};
+
+/*
+ * IEN  - Input Enable
+ * IDIS - Input Disable
+ * PTD  - Pull type Down
+ * PTU  - Pull type Up
+ * DIS  - Pull type selection is inactive
+ * EN   - Pull type selection is active
+ * M0   - Mode 0
+ * The commented string gives the final mux configuration for that pin
+ */
+#define MUX_MCX() \
+	/* SDRC */\
+	MUX_VAL(CP(SDRC_D0),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D1),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D2),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D3),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D4),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D5),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D6),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D7),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D8),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D9),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D10),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D11),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D12),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D13),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D14),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D15),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D16),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D17),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D18),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D19),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D20),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D21),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D22),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D23),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D24),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D25),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D26),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D27),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D28),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D29),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D30),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_D31),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_CLK),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_DQS0),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_DQS1),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_DQS2),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_DQS3),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SDRC_DQS0N),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(SDRC_DQS1N),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(SDRC_DQS2N),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(SDRC_DQS3N),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(SDRC_CKE0),		(M0)) \
+	MUX_VAL(CP(SDRC_CKE1),		(M0)) \
+	MUX_VAL(CP(STRBEN_DLY0),	(IEN  | PTD | EN  | M0)) \
+					/*sdrc_strben_dly0*/\
+	MUX_VAL(CP(STRBEN_DLY1),	(IEN  | PTD | EN  | M0)) \
+					/*sdrc_strben_dly1*/\
+	/* GPMC */\
+	MUX_VAL(CP(GPMC_A1),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_A2),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_A3),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_A4),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_A5),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_A6),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_A7),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_A8),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_A9),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_A10),		(IDIS | PTU | DIS | M4)) \
+					/* GPIO_43 LCD buffer enable */ \
+	MUX_VAL(CP(GPMC_D0),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D1),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D2),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D3),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D4),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D5),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D6),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D7),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D8),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D9),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D10),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D11),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D12),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D13),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D14),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_D15),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_NCS0),		(IDIS | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_NCS1),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_NCS2),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_NCS3),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_NCS4),		(IEN | PTU | EN  | M4))\
+	MUX_VAL(CP(GPMC_NCS5),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_NCS6),		(IEN | PTU | EN  | M4)) \
+					/* GPIO_57 TS_PenIRQn */\
+	MUX_VAL(CP(GPMC_NCS7),		(IEN | PTU | EN  | M4)) \
+					/* GPIO_58 ETHERNET RESET */\
+	MUX_VAL(CP(GPMC_CLK),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(GPMC_NADV_ALE),	(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(GPMC_NOE),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(GPMC_NWE),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(GPMC_NBE0_CLE),	(IDIS | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_NBE1),		(IEN  | PTU | DIS  | M4)) \
+					/* GPIO_61 SD-CARD CD */ \
+	MUX_VAL(CP(GPMC_NWP),		(IDIS  | PTU | EN | M4)) \
+			/* GPIO_62 Nand write protect, keep enabled */ \
+	MUX_VAL(CP(GPMC_WAIT0),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(GPMC_WAIT1),		(IEN | PTU | EN  | M4))\
+	MUX_VAL(CP(GPMC_WAIT2),		(IEN  | PTU | EN  | M4))\
+	MUX_VAL(CP(GPMC_WAIT3),		(IEN | PTU | EN  | M4)) \
+					/* GPIO_65 SD-CARD WP */\
+	/* DSS */\
+	MUX_VAL(CP(DSS_PCLK),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_HSYNC),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_VSYNC),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_ACBIAS),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA0),		(IEN | PTU | EN  | M4))\
+	MUX_VAL(CP(DSS_DATA1),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(DSS_DATA2),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(DSS_DATA3),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA4),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA5),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA6),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA7),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA8),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(DSS_DATA9),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(DSS_DATA10),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA11),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA12),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA13),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA14),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA15),		(IDIS | PTD | DIS | M0))\
+	MUX_VAL(CP(DSS_DATA16),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(DSS_DATA17),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(DSS_DATA18),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(DSS_DATA19),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA20),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA21),		(IDIS | PTD | DIS | M0))  \
+	MUX_VAL(CP(DSS_DATA22),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(DSS_DATA23),		(IDIS | PTD | DIS | M0)) \
+	/* CAMERA */\
+	MUX_VAL(CP(CAM_HS),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(CAM_VS),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(CAM_XCLKA),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_PCLK),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(CAM_FLD),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D0),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D1),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D2),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D3),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D4),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D5),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D6),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D7),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D8),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D9),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D10),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_D11),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_XCLKB),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_WEN),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CAM_STROBE),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CSI2_DX0),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CSI2_DY0),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CSI2_DX1),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CSI2_DY1),		(IEN  | PTD | EN  | M4)) \
+	/* MMC */\
+	MUX_VAL(CP(MMC1_CLK),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(MMC1_CMD),		(IEN  | PTU | DIS | M0)) \
+	MUX_VAL(CP(MMC1_DAT0),		(IEN  | PTU | DIS | M0)) \
+	MUX_VAL(CP(MMC1_DAT1),		(IEN  | PTU | DIS | M0)) \
+	MUX_VAL(CP(MMC1_DAT2),		(IEN  | PTU | DIS | M0)) \
+	MUX_VAL(CP(MMC1_DAT3),		(IEN  | PTU | DIS | M0)) \
+	MUX_VAL(CP(MMC1_DAT4),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MMC1_DAT5),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MMC1_DAT6),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MMC1_DAT7),		(IEN  | PTU | EN  | M4)) \
+	\
+	MUX_VAL(CP(MMC2_CLK),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(MMC2_CMD),		(IDIS | PTD | DIS | M4)) \
+					/* GPIO_131 LCD Enable */ \
+	MUX_VAL(CP(MMC2_DAT0),		(IDIS | PTD | DIS  | M4)) \
+					/* GPIO_132 USB host Enable */\
+	MUX_VAL(CP(MMC2_DAT1),		(IDIS  | PTD | DIS  | M4)) \
+					/* GPIO_133 HDMI PD */\
+	MUX_VAL(CP(MMC2_DAT2),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MMC2_DAT3),		(IEN  | PTU | EN  | M4))\
+	/* McBSP */\
+	MUX_VAL(CP(MCBSP_CLKS),		(IEN  | PTU | DIS | M0)) \
+	MUX_VAL(CP(MCBSP1_CLKR),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(MCBSP1_FSR),		(IDIS | PTU | EN  | M0)) \
+	MUX_VAL(CP(MCBSP1_DX),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(MCBSP1_DR),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(MCBSP1_FSX),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(MCBSP1_CLKX),	(IEN  | PTD | DIS | M0)) \
+	\
+	MUX_VAL(CP(MCBSP2_FSX),		(IEN  | PTU | EN  | M4))\
+	MUX_VAL(CP(MCBSP2_CLKX),	(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MCBSP2_DR),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MCBSP2_DX),		(IEN  | PTU | EN  | M4))\
+	\
+	MUX_VAL(CP(MCBSP3_DX),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MCBSP3_DR),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MCBSP3_CLKX),	(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MCBSP3_FSX),		(IEN  | PTU | EN  | M4))\
+	\
+	MUX_VAL(CP(MCBSP4_CLKX),	(IDIS | PTD | DIS | M4)) \
+					/* GPIO_152 USB phy2 reset */\
+	MUX_VAL(CP(MCBSP4_DR),		(IEN | PTU | EN | M4)) \
+					/* GPIO_153 */\
+	MUX_VAL(CP(MCBSP4_DX),		(IDIS | PTD | DIS | M4)) \
+					/* GPIO_154 USB phy1 reset */\
+	MUX_VAL(CP(MCBSP4_FSX),		(IEN | PTU | EN | M4)) \
+					/* GPIO_155 TS_BUSY */\
+	/* UART */\
+	MUX_VAL(CP(UART1_TX),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(UART1_RTS),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(UART1_CTS),		(IEN  | PTU | DIS | M0)) \
+	MUX_VAL(CP(UART1_RX),		(IEN  | PTD | DIS | M0)) \
+	\
+	MUX_VAL(CP(UART2_CTS),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(UART2_RTS),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(UART2_TX),		(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(UART2_RX),		(IEN  | PTD | DIS | M0)) \
+	\
+	MUX_VAL(CP(UART3_CTS_RCTX),	(IEN  | PTU | DIS | M0)) \
+	MUX_VAL(CP(UART3_RTS_SD),	(IDIS | PTD | DIS | M0)) \
+	MUX_VAL(CP(UART3_RX_IRRX),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(UART3_TX_IRTX),	(IDIS | PTD | DIS | M0)) \
+	/* I2C */\
+	MUX_VAL(CP(I2C1_SCL),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(I2C1_SDA),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(I2C2_SCL),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(I2C2_SDA),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(I2C3_SCL),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(I2C3_SDA),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(I2C4_SCL),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(I2C4_SDA),		(IEN  | PTU | EN  | M0)) \
+	/* McSPI */\
+	MUX_VAL(CP(MCSPI1_CLK),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(MCSPI1_SIMO),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(MCSPI1_SOMI),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(MCSPI1_CS0),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(MCSPI1_CS1),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MCSPI1_CS2),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MCSPI1_CS3),		(IEN  | PTU | EN  | M4)) \
+	MUX_VAL(CP(MCSPI2_CLK),		(IEN  | PTD | DIS | M3)) \
+					/* HSUSB2_dat7 */\
+	MUX_VAL(CP(MCSPI2_SIMO),	(IEN  | PTD | DIS | M3)) \
+					/* HSUSB2_dat4 */\
+	MUX_VAL(CP(MCSPI2_SOMI),	(IEN  | PTD | DIS | M3)) \
+					/* HSUSB2_dat5 */\
+	MUX_VAL(CP(MCSPI2_CS0),		(IEN  | PTD | DIS | M3)) \
+					/* HSUSB2_dat6 */\
+	MUX_VAL(CP(MCSPI2_CS1),		(IEN  | PTD | DIS | M3)) \
+					/* HSUSB2_dat3 */\
+	/* CCDC */\
+	MUX_VAL(CP(CCDC_PCLK),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_FIELD),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_HD),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_VD),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_WEN),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_DATA0),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_DATA1),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_DATA2),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_DATA3),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_DATA4),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_DATA5),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_DATA6),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(CCDC_DATA7),		(IEN  | PTD | EN  | M4)) \
+	/* RMII */\
+	MUX_VAL(CP(RMII_MDIO_DATA),	(IEN  |  M0)) \
+	MUX_VAL(CP(RMII_MDIO_CLK),	(M0)) \
+	MUX_VAL(CP(RMII_RXD0),		(IEN  | PTD | M0)) \
+	MUX_VAL(CP(RMII_RXD1),		(IEN  | PTD | M0)) \
+	MUX_VAL(CP(RMII_CRS_DV),	(IEN  | PTD | M0)) \
+	MUX_VAL(CP(RMII_RXER),		(PTD | M0)) \
+	MUX_VAL(CP(RMII_TXD0),		(PTD | M0)) \
+	MUX_VAL(CP(RMII_TXD1),		(PTD | M0)) \
+	MUX_VAL(CP(RMII_TXEN),		(PTD | M0)) \
+	MUX_VAL(CP(RMII_50MHZ_CLK),	(IEN  | PTD | EN  | M0)) \
+	/* HECC */\
+	MUX_VAL(CP(HECC1_TXD),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(HECC1_RXD),		(IEN  | PTD | EN  | M4)) \
+	/* HSUSB */\
+	MUX_VAL(CP(HSUSB0_CLK),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(HSUSB0_STP),		(IDIS | PTU | EN  | M0)) \
+	MUX_VAL(CP(HSUSB0_DIR),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(HSUSB0_NXT),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(HSUSB0_DATA0),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(HSUSB0_DATA1),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(HSUSB0_DATA2),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(HSUSB0_DATA3),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(HSUSB0_DATA4),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(HSUSB0_DATA5),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(HSUSB0_DATA6),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(HSUSB0_DATA7),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(USB0_DRVBUS),	(IEN  | PTD | EN  | M0)) \
+	/* HDQ */\
+	MUX_VAL(CP(HDQ_SIO),		(IEN  | PTD | EN  | M4)) \
+	/* Control and debug */\
+	MUX_VAL(CP(SYS_32K),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(SYS_CLKREQ),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SYS_NIRQ),		(IEN  | PTD | EN  | M4)) \
+	MUX_VAL(CP(SYS_NRESWARM),	(IEN | PTU | DIS | M4)) \
+					/* SYS_nRESWARM */\
+	MUX_VAL(CP(SYS_BOOT0),		(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(SYS_BOOT1),		(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(SYS_BOOT2),		(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(SYS_BOOT3),		(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(SYS_BOOT4),		(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(SYS_BOOT5),		(IEN  | PTD | DIS | M4))\
+	MUX_VAL(CP(SYS_BOOT6),		(IEN  | PTD | DIS | M4))\
+	MUX_VAL(CP(SYS_BOOT7),		(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(SYS_BOOT8),		(IEN  | PTD | DIS | M4)) \
+	\
+	MUX_VAL(CP(SYS_OFF_MODE),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(SYS_CLKOUT1),	(IEN  | PTD | DIS | M4))\
+	MUX_VAL(CP(SYS_CLKOUT2),	(IDIS | PTU | DIS | M4))\
+	/* JTAG */\
+	MUX_VAL(CP(JTAG_nTRST),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(JTAG_TCK),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(JTAG_TMS),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(JTAG_TDI),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(JTAG_EMU0),		(IEN | PTU | EN  | M4)) \
+	MUX_VAL(CP(JTAG_EMU1),		(IEN | PTU | EN  | M4))\
+	/* ETK (ES2 onwards) */\
+	MUX_VAL(CP(ETK_CLK_ES2),	(IDIS  | PTD | DIS | M3)) \
+					/* hsusb1_stp */ \
+	MUX_VAL(CP(ETK_CTL_ES2),	(IDIS  | PTD | DIS | M3)) \
+					/* hsusb1_clk */\
+	MUX_VAL(CP(ETK_D0_ES2),		(IEN  | PTD | EN | M3)) \
+	MUX_VAL(CP(ETK_D1_ES2),		(IEN  | PTD | EN | M3)) \
+	MUX_VAL(CP(ETK_D2_ES2),		(IEN  | PTD | EN | M3)) \
+	MUX_VAL(CP(ETK_D3_ES2),		(IEN  | PTD | EN | M3)) \
+	MUX_VAL(CP(ETK_D4_ES2),		(IEN  | PTD | EN | M3)) \
+	MUX_VAL(CP(ETK_D5_ES2),		(IEN  | PTD | EN | M3)) \
+	MUX_VAL(CP(ETK_D6_ES2),		(IEN  | PTD | EN | M3)) \
+	MUX_VAL(CP(ETK_D7_ES2),		(IEN  | PTD | EN | M3)) \
+	MUX_VAL(CP(ETK_D8_ES2),		(IEN  | PTD | EN | M3)) \
+	MUX_VAL(CP(ETK_D9_ES2),		(IEN  | PTD | EN | M3)) \
+	MUX_VAL(CP(ETK_D10_ES2),	(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(ETK_D11_ES2),	(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(ETK_D13_ES2),	(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(ETK_D14_ES2),	(IEN  | PTD | DIS | M4)) \
+	MUX_VAL(CP(ETK_D15_ES2),	(IEN  | PTD | DIS | M4)) \
+	/* Die to Die */\
+	MUX_VAL(CP(D2D_MCAD34),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(D2D_MCAD35),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(D2D_MCAD36),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(D2D_CLK26MI),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_NRESPWRON),	(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(D2D_NRESWARM),	(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(D2D_ARM9NIRQ),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_UMA2P6FIQ),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_SPINT),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(D2D_FRINT),		(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(D2D_DMAREQ0),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_DMAREQ1),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_DMAREQ2),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_DMAREQ3),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_N3GTRST),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_N3GTDI),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_N3GTDO),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_N3GTMS),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_N3GTCK),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_N3GRTCK),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_MSTDBY),		(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(D2D_SWAKEUP),	(IEN  | PTD | EN  | M0)) \
+	MUX_VAL(CP(D2D_IDLEREQ),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_IDLEACK),	(IEN  | PTU | EN  | M0)) \
+	MUX_VAL(CP(D2D_MWRITE),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_SWRITE),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_MREAD),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_SREAD),		(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_MBUSFLAG),	(IEN  | PTD | DIS | M0)) \
+	MUX_VAL(CP(D2D_SBUSFLAG),	(IEN  | PTD | DIS | M0)) \
+
+#endif
diff --git a/boards.cfg b/boards.cfg
index d3d610d..7f656f6 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -183,6 +183,7 @@ omap3_beagle                 arm         armv7       beagle              ti
 omap3_evm                    arm         armv7       evm                 ti             omap3
 omap3_sdp3430                arm         armv7       sdp3430             ti             omap3
 devkit8000                   arm         armv7       devkit8000          timll          omap3
+mcx                          arm         armv7       mcx                 htkw           omap3
 omap4_panda                  arm         armv7       panda               ti             omap4
 omap4_sdp4430                arm         armv7       sdp4430             ti             omap4
 s5p_goni                     arm         armv7       goni                samsung        s5pc1xx
diff --git a/include/configs/mcx.h b/include/configs/mcx.h
new file mode 100644
index 0000000..25fd610
--- /dev/null
+++ b/include/configs/mcx.h
@@ -0,0 +1,302 @@
+/*
+ * Copyright (C) 2011 Ilya Yanok, Emcraft Systems
+ *
+ * Based on omap3_evm_config.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_OMAP			/* in a TI OMAP core */
+#define CONFIG_OMAP34XX			/* which is a 34XX */
+#define CONFIG_OMAP3_MCX		/* working with mcx */
+
+#define CONFIG_MACH_TYPE	MACH_TYPE_MCX
+
+#define CONFIG_SYS_CACHELINE_SIZE	64
+
+#define CONFIG_EMIF4	/* The chip has EMIF4 controller */
+
+#include <asm/arch/cpu.h>		/* get chip and board defs */
+#include <asm/arch/omap3.h>
+
+#define CONFIG_OF_LIBFDT
+#define CONFIG_FIT
+
+#define CONFIG_SYS_TEXT_BASE		0x80008000
+
+/*
+ * Display CPU and Board information
+ */
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+/* Clock Defines */
+#define V_OSCK			26000000	/* Clock output from T2 */
+#define V_SCLK			(V_OSCK >> 1)
+
+#undef CONFIG_USE_IRQ				/* no support for IRQs */
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_CMDLINE_TAG			/* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_ENV_SIZE			(128 << 10)	/* 128 KiB sector */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (128 << 10))
+/*
+ * DDR related
+ */
+#define CONFIG_OMAP3_MICRON_DDR			/* Micron DDR */
+#define CONFIG_SYS_CS0_SIZE		(256 * 1024 * 1024)
+
+/*
+ * Hardware drivers
+ */
+
+/*
+ * NS16550 Configuration
+ */
+#define V_NS16550_CLK			48000000	/* 48MHz (APLL96/2) */
+
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
+#define CONFIG_SYS_NS16550_CLK		V_NS16550_CLK
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_CONS_INDEX		3
+#define CONFIG_SYS_NS16550_COM3		OMAP34XX_UART3
+#define CONFIG_SERIAL3			3	/* UART3 */
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{4800, 9600, 19200, 38400, 57600,\
+					115200}
+#define CONFIG_MMC
+#define CONFIG_OMAP_HSMMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_DOS_PARTITION
+
+/* commands to include */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_EXT2		/* EXT2 Support			*/
+#define CONFIG_CMD_FAT		/* FAT support			*/
+#define CONFIG_CMD_JFFS2	/* JFFS2 Support		*/
+
+#define CONFIG_CMD_I2C		/* I2C serial bus support	*/
+#define CONFIG_CMD_MMC		/* MMC support			*/
+#define CONFIG_CMD_FAT		/* FAT support			*/
+#define CONFIG_CMD_NAND		/* NAND support			*/
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+
+#undef CONFIG_CMD_FLASH		/* flinfo, erase, protect	*/
+#undef CONFIG_CMD_FPGA		/* FPGA configuration Support	*/
+#undef CONFIG_CMD_IMI		/* iminfo			*/
+#undef CONFIG_CMD_IMLS		/* List all found images	*/
+
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_HARD_I2C
+#define CONFIG_SYS_I2C_SPEED		100000
+#define CONFIG_SYS_I2C_SLAVE		1
+#define CONFIG_SYS_I2C_BUS		0
+#define CONFIG_DRIVER_OMAP34XX_I2C
+
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NFS
+/*
+ * Board NAND Info.
+ */
+#define CONFIG_SYS_NAND_ADDR		NAND_BASE	/* physical address */
+							/* to access nand */
+#define CONFIG_SYS_NAND_BASE		NAND_BASE	/* physical address */
+							/* to access */
+							/* nand at CS0 */
+
+#define CONFIG_SYS_MAX_NAND_DEVICE	1		/* Max number of */
+							/* NAND devices */
+#define CONFIG_SYS_64BIT_VSPRINTF		/* needed for nand_util.c */
+
+#define CONFIG_JFFS2_NAND
+/* nand device jffs2 lives on */
+#define CONFIG_JFFS2_DEV		"nand0"
+/* start of jffs2 partition */
+#define CONFIG_JFFS2_PART_OFFSET	0x680000
+#define CONFIG_JFFS2_PART_SIZE		0xf980000	/* sz of jffs2 part */
+
+/* Environment information */
+#define CONFIG_BOOTDELAY	10
+
+#define CONFIG_BOOTFILE		uImage
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"loadaddr=0x82000000\0" \
+	"console=ttyO2,115200n8\0" \
+	"mmcargs=setenv bootargs console=${console} " \
+		"root=/dev/mmcblk0p2 rw " \
+		"rootfstype=ext3 rootwait\0" \
+	"nandargs=setenv bootargs console=${console} " \
+		"root=/dev/mtdblock4 rw " \
+		"rootfstype=jffs2\0" \
+	"loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
+	"bootscript=echo Running bootscript from mmc ...; " \
+		"source ${loadaddr}\0" \
+	"loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; " \
+		"bootm ${loadaddr}\0" \
+	"nandboot=echo Booting from nand ...; " \
+		"run nandargs; " \
+		"nand read ${loadaddr} 280000 400000; " \
+		"bootm ${loadaddr}\0" \
+
+#define CONFIG_BOOTCOMMAND \
+	"if mmc init; then " \
+		"if run loadbootscript; then " \
+			"run bootscript; " \
+		"else " \
+			"if run loaduimage; then " \
+				"run mmcboot; " \
+			"else run nandboot; " \
+			"fi; " \
+		"fi; " \
+	"else run nandboot; fi"
+
+#define CONFIG_AUTO_COMPLETE
+/*
+ * Miscellaneous configurable options
+ */
+#define V_PROMPT			"mcx # "
+
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser */
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+#define CONFIG_SYS_PROMPT		V_PROMPT
+#define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
+					sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS		32	/* max number of command */
+						/* args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE		(CONFIG_SYS_CBSIZE)
+/* memtest works on */
+#define CONFIG_SYS_MEMTEST_START	(OMAP34XX_SDRC_CS0)
+#define CONFIG_SYS_MEMTEST_END		(OMAP34XX_SDRC_CS0 + \
+					0x01F00000) /* 31MB */
+
+#define CONFIG_SYS_LOAD_ADDR		(OMAP34XX_SDRC_CS0) /* default load */
+								/* address */
+
+/*
+ * AM3517 has 12 GP timers, they can be driven by the system clock
+ * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
+ * This rate is divided by a local divisor.
+ */
+#define CONFIG_SYS_TIMERBASE		OMAP34XX_GPT2
+#define CONFIG_SYS_PTV			2	/* Divisor: 2^(PTV+1) => 8 */
+#define CONFIG_SYS_HZ			1000
+
+/*-----------------------------------------------------------------------
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE	(128 << 10)	/* regular stack 128 KiB */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ	(4 << 10)	/* IRQ stack 4 KiB */
+#define CONFIG_STACKSIZE_FIQ	(4 << 10)	/* FIQ stack 4 KiB */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS	2	/* CS1 may or may not be populated */
+#define PHYS_SDRAM_1		OMAP34XX_SDRC_CS0
+#define PHYS_SDRAM_1_SIZE	(32 << 20)	/*@least 32 MiB */
+#define PHYS_SDRAM_2		OMAP34XX_SDRC_CS1
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+
+/* **** PISMO SUPPORT *** */
+
+/* Configure the PISMO */
+#define PISMO1_NAND_SIZE		GPMC_SIZE_128M
+
+#define CONFIG_NAND_OMAP_GPMC
+#define GPMC_NAND_ECC_LP_x16_LAYOUT
+#define CONFIG_ENV_IS_IN_NAND
+#define SMNAND_ENV_OFFSET		0x260000 /* environment starts here */
+
+#define CONFIG_SYS_ENV_SECT_SIZE	(128 << 10)	/* 128 KiB */
+#define CONFIG_ENV_OFFSET		SMNAND_ENV_OFFSET
+#define CONFIG_ENV_ADDR			SMNAND_ENV_OFFSET
+
+/*-----------------------------------------------------------------------
+ * CFI FLASH driver setup
+ */
+/* timeout values are in ticks */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	(100 * CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT	(100 * CONFIG_SYS_HZ)
+
+/* Flash banks JFFS2 should use */
+#define CONFIG_SYS_MAX_MTD_BANKS	(CONFIG_SYS_MAX_FLASH_BANKS + \
+					CONFIG_SYS_MAX_NAND_DEVICE)
+#define CONFIG_SYS_JFFS2_MEM_NAND
+/* use flash_info[2] */
+#define CONFIG_SYS_JFFS2_FIRST_BANK	CONFIG_SYS_MAX_FLASH_BANKS
+#define CONFIG_SYS_JFFS2_NUM_BANKS	1
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_ADDR	0x4020f800
+#define CONFIG_SYS_INIT_RAM_SIZE	0x800
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
+					 CONFIG_SYS_INIT_RAM_SIZE - \
+					 GENERATED_GBL_DATA_SIZE)
+
+/*
+ * ethernet support
+ *
+ */
+#if defined(CONFIG_CMD_NET)
+#define CONFIG_DRIVER_TI_EMAC
+#define CONFIG_DRIVER_TI_EMAC_USE_RMII
+#define CONFIG_MII
+#define CONFIG_EMAC_MDIO_PHY_NUM	0
+#define	CONFIG_BOOTP_DEFAULT
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_NET_RETRY_COUNT 10
+#endif
+
+#endif /* __CONFIG_H */
-- 
1.7.6.4