[U-Boot] [GIT PULL] Pull request: u-boot-imx

Wolfgang Denk
2010-10-11T08:23:22Z

Dear Stefano Babic,

In message <4CAD8492.3000702@denx.de> you wrote:
> Hi Wolfgang,
>
> please pull from u-boot-imx.
>
> The following changes since commit 2e6e1772c0e34871769be4aef79748fe3e47d953:
> Wolfgang Denk (1):
> Merge branch 'next' of /home/wd/git/u-boot/next
>
> are available in the git repository at:
>
> git://git.denx.de/u-boot-imx master
>
> Stefano Babic (10):
> Use common function to set GPIOs for MX3 and MX5
> ARM: Use syslib functions for all CORTEXA8
> MX51: Added pins definition to set up pads
> MX51: add structure to access System Reset Controller
> MXC: Add watchdog support to serial driver
> MX51: Drop unused header file for mx51evk
> MXC: Correct SPI_CPOL setting in SPI driver
> MXC: Fix byte-ordering in SPI driver for i.MX31/i.MX51
> MX51: Register definitions cannot be included in board config file
> MX51: Support for TTECH vision2 board
>
> MAINTAINERS | 1 +
> arch/arm/cpu/armv7/Makefile | 3 +-
> arch/arm/cpu/armv7/omap-common/Makefile | 1 -
> arch/arm/cpu/armv7/{omap-common => }/syslib.c | 0
> arch/arm/include/asm/arch-mx31/mx31-regs.h | 14 +-
> arch/arm/include/asm/arch-mx31/mx31.h | 25 -
> arch/arm/include/asm/arch-mx51/imx-regs.h | 26 +-
> arch/arm/include/asm/arch-mx51/mx51_pins.h | 44 ++
> arch/arm/include/asm/arch-mx51/sys_proto.h | 1 +
> board/davedenx/qong/qong.c | 29 +-
> board/freescale/mx51evk/mx51evk.c | 2 -
> board/ttcontrol/vision2/Makefile | 48 ++
> board/ttcontrol/vision2/config.mk | 25 +
> board/ttcontrol/vision2/imximage_hynix.cfg | 209 ++++++
> board/ttcontrol/vision2/vision2.c | 711
> ++++++++++++++++++++
> boards.cfg | 1 +
> drivers/gpio/Makefile | 2 +-
> drivers/gpio/{mx31_gpio.c => mxc_gpio.c} | 47 +-
> drivers/misc/fsl_pmic.c | 10 +-
> drivers/serial/serial_mxc.c | 7 +-
> drivers/spi/mxc_spi.c | 168 ++++--
> include/configs/imx31_litekit.h | 4 +-
> include/configs/imx31_phycore.h | 2 +-
> include/configs/mx31ads.h | 4 +-
> include/configs/mx31pdk.h | 4 +-
> include/configs/mx51evk.h | 2 +-
> include/configs/qong.h | 6 +-
> include/configs/vision2.h | 214 ++++++
> include/mc13892.h | 3 +
> .../mx51evk/mx51evk.h => include/mxc_gpio.h | 50 +-
> 30 files changed, 1510 insertions(+), 153 deletions(-)
> rename arch/arm/cpu/armv7/{omap-common => }/syslib.c (100%)
> create mode 100644 board/ttcontrol/vision2/Makefile
> create mode 100644 board/ttcontrol/vision2/config.mk
> create mode 100644 board/ttcontrol/vision2/imximage_hynix.cfg
> create mode 100644 board/ttcontrol/vision2/vision2.c
> rename drivers/gpio/{mx31_gpio.c => mxc_gpio.c} (63%)
> create mode 100644 include/configs/vision2.h
> rename board/freescale/mx51evk/mx51evk.h => include/mxc_gpio.h (54%)

Applied, thanks.

Best regards,

Wolfgang Denk

--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"Though a program be but three lines long,
someday it will have to be maintained."
- The Tao of Programming