[U-Boot] [PATCH] ulpi: add generic ULPI support header file

[Igor Grinberg <grinberg@compulab.co.il>]

Hi Jana,

On 11/01/11 21:12, Jana Rapava wrote:
> Add ULPI header file needed by Efika USB support patchset and generic
> ULPI support patch, which is to be posted soon.
> 
> Signed-off-by: Jana Rapava <fermata7@gmail.com>
> Cc: Marek Vasut <marek.vasut@gmail.com>
> Cc: Remy Bohmer <linux@bohmer.net>
> Cc: Stefano Babic <sbabic@denx.de>
> Cc: Igor Grinberg <grinberg@compulab.co.il>
> ---
>  include/usb/ulpi.h |  195 ++++++++++++++++++++++++++++++++++++++++++++++++++++
>  1 files changed, 195 insertions(+), 0 deletions(-)
>  create mode 100644 include/usb/ulpi.h
> 
> diff --git a/include/usb/ulpi.h b/include/usb/ulpi.h
> new file mode 100644
> index 0000000..4a88b5f
> --- /dev/null
> +++ b/include/usb/ulpi.h
> @@ -0,0 +1,195 @@
> +/*
> + * Copyright (C) 2011 Jana Rapava <fermata7@gmail.com>
> + * Based on:
> + * linux/include/linux/usb/ulpi.h
> + * ULPI defines and function prototypes
> + *
> + * Original Copyrights follow:
> + * Copyright (C) 2010 Nokia Corporation
> + *
> + * This software is distributed under the terms of the GNU General
> + * Public License ("GPL") as published by the Free Software Foundation,
> + * version 2 of that License.
> + */
> +
> +#ifndef __USB_ULPI_H
> +#define __USB_ULPI_H
> +
> +#define ULPI_ID_REGS_COUNT	4
> +#define ULPI_TEST_VALUE		0x55
> +#define ULPI_TIMEOUT		1000 /* some reasonable value */
> +
> +/* ULPI viewport control bits */
> +#define ULPI_WU		(1 << 31)
> +#define ULPI_SS		(1 << 27)
> +#define ULPI_RWRUN	(1 << 30)
> +#define ULPI_RWCTRL	(1 << 29)
> +
> +struct ulpi_regs {
> +	u8	vendor_id_low;		/* 0x00 - Vendor ID lower byte */
> +	u8	vendor_id_high;		/* 0x01 - Vendor ID upper byte */
> +	u8	product_id_low;		/* 0x02 - Product ID lower byte */
> +	u8	product_id_high;	/* 0x03 - Product ID higher byte */
> +	/* Function Control; 0x04 - 0x06 Read, 0x04 Write */
> +	u8	function_ctrl_write;
> +	u8	function_ctrl_set;	/* 0x05 Set */
> +	u8	function_ctrl_clear;	/* 0x06 Clear */
> +	/* Interface Control; 0x07 - 0x09 Read, 0x07 Write */
> +	u8	iface_ctrl_write;
> +	u8	iface_ctrl_set;		/* 0x08 Set */
> +	u8	iface_ctrl_clear;	/* 0x09 Clear */
> +	/* OTG Control; 0x0A - 0x0C Read, 0x0A Write */
> +	u8	otg_ctrl_write;
> +	u8	otg_ctrl_set;		/* 0x0B Set */
> +	u8	otg_ctrl_clear;		/* 0x0C Clear */
> +	/* USB Interrupt Enable Rising; 0x0D - 0x0F Read, 0x0D Write */
> +	u8	usb_ie_rising_write;
> +	u8	usb_ie_rising_set;	/* 0x0E Set */
> +	u8	usb_ie_rising_clear;	/* 0x0F Clear */
> +	/* USB Interrupt Enable Falling; 0x10 - 0x12 Read, 0x10 Write */
> +	u8	usb_ie_falling_write;
> +	u8	usb_ie_falling_set;	/* 0x11 Set */
> +	u8	usb_ie_falling_clear;	/* 0x12 Clear */
> +	u8	usb_int_status;		/* 0x13 - USB Interrupt Status */
> +	u8	usb_int_latch;		/* 0x14 - USB Interrupt Latch */
> +	u8	debug;			/* 0x15 - Debug */
> +	/* Scratch Register; 0x16 - 0x18 Read, 0x16 Write */
> +	u8	scratch_write;
> +	u8	scratch_set;		/* 0x17 Set */
> +	u8	scratch_clear;		/* 0x18 Clear */
> +	/*
> +	 * Optional Carkit registers
> +	 */
> +	/* Carkit Control; 0x19 - 0x1B Read, 0x19 Write */
> +	u8 carkit_ctrl_write;
> +	u8 carkit_ctrl_set;
> +	u8 carkit_ctrl_clear;
> +	/* Carkit Interrupt Delay */
> +	u8 carkit_int_delay;		/* 0x1C Read, Write */
> +	/* Carkit Interrupt Enable; 0x1D - 0x1F Read, 0x1D Write */
> +	u8 carkit_ie_write;
> +	u8 carkit_ie_set;
> +	u8 carkit_ie_clear;
> +	u8 carkit_int_status;		/* 0x20 - Carkit Interrupt Status */
> +	u8 carkit_int_latch;		/* 0x21 - Carkit Interrupt Latch */
> +	/* Carkit Pulse Control; 0x22 - 0x24 Read, 0x22 Write */
> +	u8 carkit_pulse_ctrl_write;
> +	u8 carkit_pulse_ctrl_set;
> +	u8 carkit_pulse_ctrl_clear;
> +	/*
> +	 * Other optional registers
> +	 */
> +	u8	transmit_pos_width;	/* 0x25 - Transmit Positive Width */
> +	u8	transmit_neg_width;	/* 0x26 - Transmit Negative Width */
> +	u8	recv_pol_recovery;	/* 0x27 - Receive Polarity Recovery */
> +	/*
> +	 * Addresses 0x28 - 0x2E are reserved, so we use offsets
> +	 * for immediate registers with higher addresses
> +	 */
> +};

In the structure above, you have a mixture of tab and spaces
after the type before the name.
You can use either tabs or spaces (I prefer spaces), but not both.

> +
> +/* Access Extended Register Set (indicator) */
> +#define ACCESS_EXT_REGS_OFFSET	0x2f	/* read-write */
> +/* Vendor-specific */
> +#define VENDOR_SPEC_OFFSET	0x30
> +
> +/*
> + * Extended Register Set
> + *
> + * Addresses 0x00-0x3F map directly to Immediate Register Set.
> + * Addresses 0x40-0x7F are reserved.
> + * Addresses 0x80-0xff are vendor-specific.
> + */
> +#define EXT_VENDOR_SPEC_OFFSET	0x80
> +
> +/*
> + * Register Bits
> + */
> +
> +/* Function Control */
> +#define ULPI_FC_XCVRSEL			(1 << 0)
> +#define ULPI_FC_XCVRSEL_MASK		(3 << 0)
> +#define ULPI_FC_HIGH_SPEED		(0 << 0)
> +#define ULPI_FC_FULL_SPEED		(1 << 0)
> +#define ULPI_FC_LOW_SPEED		(2 << 0)
> +#define ULPI_FC_FS4LS			(3 << 0)
> +#define ULPI_FC_TERMSELECT		(1 << 2)
> +#define ULPI_FC_OPMODE			(1 << 3)
> +#define ULPI_FC_OPMODE_MASK		(3 << 3)
> +#define ULPI_FC_OPMODE_NORMAL		(0 << 3)
> +#define ULPI_FC_OPMODE_NONDRIVING	(1 << 3)
> +#define ULPI_FC_OPMODE_DISABLE_NRZI	(2 << 3)
> +#define ULPI_FC_OPMODE_NOSYNC_NOEOP	(3 << 3)
> +#define ULPI_FC_RESET			(1 << 5)
> +#define ULPI_FC_SUSPENDM		(1 << 6)
> +
> +/* Interface Control */
> +#define ULPI_IFACE_6_PIN_SERIAL_MODE	(1 << 0)
> +#define ULPI_IFACE_3_PIN_SERIAL_MODE	(1 << 1)
> +#define ULPI_IFACE_CARKITMODE		(1 << 2)
> +#define ULPI_IFACE_CLOCKSUSPENDM	(1 << 3)
> +#define ULPI_IFACE_AUTORESUME		(1 << 4)
> +#define ULPI_IFACE_EXTVBUS_COMPLEMENT	(1 << 5)
> +#define ULPI_IFACE_PASSTHRU		(1 << 6)
> +#define ULPI_IFACE_PROTECT_IFC_DISABLE	(1 << 7)
> +
> +/* OTG Control */
> +#define ULPI_OTG_ID_PULLUP		(1 << 0)
> +#define ULPI_OTG_DP_PULLDOWN		(1 << 1)
> +#define ULPI_OTG_DM_PULLDOWN		(1 << 2)
> +#define ULPI_OTG_DISCHRGVBUS		(1 << 3)
> +#define ULPI_OTG_CHRGVBUS		(1 << 4)
> +#define ULPI_OTG_DRVVBUS		(1 << 5)
> +#define ULPI_OTG_DRVVBUS_EXT		(1 << 6)
> +#define ULPI_OTG_EXTVBUSIND		(1 << 7)
> +
> +/*
> + * USB Interrupt Enable Rising,
> + * USB Interrupt Enable Falling,
> + * USB Interrupt Status and
> + * USB Interrupt Latch
> + */
> +#define ULPI_INT_HOST_DISCONNECT		(1 << 0)
> +#define ULPI_INT_VBUS_VALID			(1 << 1)
> +#define ULPI_INT_SESS_VALID			(1 << 2)
> +#define ULPI_INT_SESS_END			(1 << 3)
> +#define ULPI_INT_IDGRD				(1 << 4)
> +
> +/* Debug */
> +#define ULPI_DEBUG_LINESTATE0			(1 << 0)
> +#define ULPI_DEBUG_LINESTATE1			(1 << 1)
> +
> +/* Carkit Control */
> +#define ULPI_CARKIT_CTRL_CARKITPWR		(1 << 0)
> +#define ULPI_CARKIT_CTRL_IDGNDDRV		(1 << 1)
> +#define ULPI_CARKIT_CTRL_TXDEN			(1 << 2)
> +#define ULPI_CARKIT_CTRL_RXDEN			(1 << 3)
> +#define ULPI_CARKIT_CTRL_SPKLEFTEN		(1 << 4)
> +#define ULPI_CARKIT_CTRL_SPKRIGHTEN		(1 << 5)
> +#define ULPI_CARKIT_CTRL_MICEN			(1 << 6)
> +
> +/* Carkit Interrupt Enable */
> +#define ULPI_CARKIT_INT_EN_IDFLOAT_RISE		(1 << 0)
> +#define ULPI_CARKIT_INT_EN_IDFLOAT_FALL		(1 << 1)
> +#define ULPI_CARKIT_INT_EN_CARINTDET		(1 << 2)
> +#define ULPI_CARKIT_INT_EN_DP_RISE		(1 << 3)
> +#define ULPI_CARKIT_INT_EN_DP_FALL		(1 << 4)
> +
> +/*
> + * Carkit Interrupt Status and
> + * Carkit Interrupt Latch
> + */
> +#define ULPI_CARKIT_INT_IDFLOAT			(1 << 0)
> +#define ULPI_CARKIT_INT_CARINTDET		(1 << 1)
> +#define ULPI_CARKIT_INT_DP			(1 << 2)
> +
> +/* Carkit Pulse Control*/
> +#define ULPI_CARKIT_PLS_CTRL_TXPLSEN		(1 << 0)
> +#define ULPI_CARKIT_PLS_CTRL_RXPLSEN		(1 << 1)
> +#define ULPI_CARKIT_PLS_CTRL_SPKRLEFT_BIASEN	(1 << 2)
> +#define ULPI_CARKIT_PLS_CTRL_SPKRRIGHT_BIASEN	(1 << 3)
> +
> +void ulpi_write(struct usb_ehci *ehci, u32 reg, u32 value);
> +u32 ulpi_read(struct usb_ehci *ehci, u32 reg);
> +
> +#endif /* __USB_ULPI_H */

-- 
Regards,
Igor.