[U-Boot] [PATCH v3] ulpi: add generic ULPI support header file

Igor Grinberg
2011-11-14T08:22:07Z

Also, now I think it makes sense to amend this patch into
the "ulpi: add generic ULPI functionality" patch.

On 11/14/11 10:01, Igor Grinberg wrote:
> Hi Jana,
>
> On 11/12/11 19:17, Jana Rapava wrote:
>> Add ULPI header file needed by Efika USB support patchset and generic
>> ULPI support patch.
>>
>> Signed-off-by: Jana Rapava <fermata7@gmail.com>
>> Cc: Marek Vasut <marek.vasut@gmail.com>
>> Cc: Remy Bohmer <linux@bohmer.net>
>> Cc: Stefano Babic <sbabic@denx.de>
>> Cc: Igor Grinberg <grinberg@compulab.co.il>
>> Cc: Wolfgang Grandegger <wg@denx.de>
>> ---
>> This patch is a prerequisite for Efika USB patchset.
>>
>> Changes for v2:
>> - whitespace and comment changes
>> Changes for v3:
>> - remove _write suffix in register names
>> - change first argument of ULPI-related functions from "ehci"
>> to "ulpi_viewport"
>>
>> include/usb/ulpi.h | 220 ++++++++++++++++++++++++++++++++++++++++++++++++++++
>> 1 files changed, 220 insertions(+), 0 deletions(-)
>> create mode 100644 include/usb/ulpi.h
>>
>> diff --git a/include/usb/ulpi.h b/include/usb/ulpi.h
>> new file mode 100644
>> index 0000000..f131861
>> --- /dev/null
>> +++ b/include/usb/ulpi.h
>> @@ -0,0 +1,220 @@
>> +/*
>> + * Copyright (C) 2011 Jana Rapava <fermata7@gmail.com>
>> + * Based on:
>> + * linux/include/linux/usb/ulpi.h
>> + * ULPI defines and function prototypes
>> + *
>> + * Original Copyrights follow:
>> + * Copyright (C) 2010 Nokia Corporation
>> + *
>> + * This software is distributed under the terms of the GNU General
>> + * Public License ("GPL") as published by the Free Software Foundation,
>> + * version 2 of that License.
>> + */
>> +
>> +#ifndef __USB_ULPI_H
>> +#define __USB_ULPI_H
>> +
>> +#define ULPI_ID_REGS_COUNT 4
>> +#define ULPI_TEST_VALUE 0x55
>> +/* value greater than 0xff indicates failure */
>> +#define ULPI_ERROR (1 << 8)
>> +#define ULPI_TIMEOUT 1000 /* some reasonable value */
>> +
>> +/* ULPI viewport control bits */
>> +#define ULPI_WU (1 << 31)
>> +#define ULPI_SS (1 << 27)
>> +#define ULPI_RWRUN (1 << 30)
>> +#define ULPI_RWCTRL (1 << 29)
>> +
>> +/* ULPI access modes */
>> +#define ULPI_WRITE 0x00
>> +#define ULPI_SET 0x01
>> +#define ULPI_CLEAR 0x02
>> +
>> +struct ulpi_regs {
>> + /* Vendor ID and Product ID: 0x00 - 0x03 Read-only */
>> + u8 vendor_id_low;
>> + u8 vendor_id_high;
>> + u8 product_id_low;
>> + u8 product_id_high;
>> + /* Function Control: 0x04 - 0x06 Read */
>> + u8 function_ctrl; /* 0x04 Write */
>> + u8 function_ctrl_set; /* 0x05 Set */
>> + u8 function_ctrl_clear; /* 0x06 Clear */
>> + /* Interface Control: 0x07 - 0x09 Read */
>> + u8 iface_ctrl; /* 0x07 Write */
>> + u8 iface_ctrl_set; /* 0x08 Set */
>> + u8 iface_ctrl_clear; /* 0x09 Clear */
>> + /* OTG Control: 0x0A - 0x0C Read */
>> + u8 otg_ctrl; /* 0x0A Write */
>> + u8 otg_ctrl_set; /* 0x0B Set */
>> + u8 otg_ctrl_clear; /* 0x0C Clear */
>> + /* USB Interrupt Enable Rising: 0x0D - 0x0F Read */
>> + u8 usb_ie_rising; /* 0x0D Write */
>> + u8 usb_ie_rising_set; /* 0x0E Set */
>> + u8 usb_ie_rising_clear; /* 0x0F Clear */
>> + /* USB Interrupt Enable Falling: 0x10 - 0x12 Read */
>> + u8 usb_ie_falling; /* 0x10 Write */
>> + u8 usb_ie_falling_set; /* 0x11 Set */
>> + u8 usb_ie_falling_clear; /* 0x12 Clear */
>> + /* USB Interrupt Status: 0x13 Read-only */
>> + u8 usb_int_status;
>> + /* USB Interrupt Latch: 0x14 Read-only with auto-clear */
>> + u8 usb_int_latch;
>> + /* Debug: 0x15 Read-only */
>> + u8 debug;
>> + /* Scratch Register: 0x16 - 0x18 Read */
>> + u8 scratch; /* 0x16 Write */
>> + u8 scratch_set; /* 0x17 Set */
>> + u8 scratch_clear; /* 0x18 Clear */
>> + /*
>> + * Optional Carkit registers
>> + */
>> + /* Carkit Control: 0x19 - 0x1B Read */
>> + u8 carkit_ctrl; /* 0x19 Write */
>> + u8 carkit_ctrl_set; /* 0x1A Set */
>> + u8 carkit_ctrl_clear; /* 0x1B Clear */
>> + /* Carkit Interrupt Delay: 0x1C Read, Write */
>> + u8 carkit_int_delay;
>> + /* Carkit Interrupt Enable: 0x1D - 0x1F Read */
>> + u8 carkit_ie; /* 0x1D Write */
>> + u8 carkit_ie_set; /* 0x1E Set */
>> + u8 carkit_ie_clear; /* 0x1F Clear */
>> + /* Carkit Interrupt Status: 0x20 Read-only */
>> + u8 carkit_int_status;
>> + /* Carkit Interrupt Latch: 0x21 Read-only with auto-clear */
>> + u8 carkit_int_latch;
>> + /* Carkit Pulse Control: 0x22 - 0x24 Read */
>> + u8 carkit_pulse_ctrl; /* 0x22 Write */
>> + u8 carkit_pulse_ctrl_set; /* 0x23 Set */
>> + u8 carkit_pulse_ctrl_clear; /* 0x24 Clear */
>> + /*
>> + * Other optional registers
>> + */
>> + /* Transmit Positive Width: 0x25 Read, Write */
>> + u8 transmit_pos_width;
>> + /* Transmit Negative Width: 0x26 Read, Write */
>> + u8 transmit_neg_width;
>> + /* Receive Polarity Recovery: 0x27 Read, Write */
>> + u8 recv_pol_recovery;
>> + /*
>> + * Addresses 0x28 - 0x2E are reserved, so we use offsets
>> + * for immediate registers with higher addresses
>> + */
>> +};
>> +
>> +/* Access Extended Register Set (indicator) */
>> +#define ACCESS_EXT_REGS_OFFSET 0x2f /* read-write */
>> +/* Vendor-specific */
>> +#define VENDOR_SPEC_OFFSET 0x30
>> +
>> +/*
>> + * Extended Register Set
>> + *
>> + * Addresses 0x00-0x3F map directly to Immediate Register Set.
>> + * Addresses 0x40-0x7F are reserved.
>> + * Addresses 0x80-0xff are vendor-specific.
>> + */
>> +#define EXT_VENDOR_SPEC_OFFSET 0x80
>> +
>> +/*
>> + * Register Bits
>> + */
>> +
>> +/* Function Control */
>> +#define ULPI_FC_XCVRSEL (1 << 0)
>> +#define ULPI_FC_XCVRSEL_MASK (3 << 0)
>> +#define ULPI_FC_HIGH_SPEED (0 << 0)
>> +#define ULPI_FC_FULL_SPEED (1 << 0)
>> +#define ULPI_FC_LOW_SPEED (2 << 0)
>> +#define ULPI_FC_FS4LS (3 << 0)
>> +#define ULPI_FC_TERMSELECT (1 << 2)
>> +#define ULPI_FC_OPMODE (1 << 3)
>> +#define ULPI_FC_OPMODE_MASK (3 << 3)
>> +#define ULPI_FC_OPMODE_NORMAL (0 << 3)
>> +#define ULPI_FC_OPMODE_NONDRIVING (1 << 3)
>> +#define ULPI_FC_OPMODE_DISABLE_NRZI (2 << 3)
>> +#define ULPI_FC_OPMODE_NOSYNC_NOEOP (3 << 3)
>> +#define ULPI_FC_RESET (1 << 5)
>> +#define ULPI_FC_SUSPENDM (1 << 6)
>> +
>> +/* Interface Control */
>> +#define ULPI_IFACE_6_PIN_SERIAL_MODE (1 << 0)
>> +#define ULPI_IFACE_3_PIN_SERIAL_MODE (1 << 1)
>> +#define ULPI_IFACE_CARKITMODE (1 << 2)
>> +#define ULPI_IFACE_CLOCKSUSPENDM (1 << 3)
>> +#define ULPI_IFACE_AUTORESUME (1 << 4)
>> +#define ULPI_IFACE_EXTVBUS_COMPLEMENT (1 << 5)
>> +#define ULPI_IFACE_PASSTHRU (1 << 6)
>> +#define ULPI_IFACE_PROTECT_IFC_DISABLE (1 << 7)
>> +
>> +/* OTG Control */
>> +#define ULPI_OTG_ID_PULLUP (1 << 0)
>> +#define ULPI_OTG_DP_PULLDOWN (1 << 1)
>> +#define ULPI_OTG_DM_PULLDOWN (1 << 2)
>> +#define ULPI_OTG_DISCHRGVBUS (1 << 3)
>> +#define ULPI_OTG_CHRGVBUS (1 << 4)
>> +#define ULPI_OTG_DRVVBUS (1 << 5)
>> +#define ULPI_OTG_DRVVBUS_EXT (1 << 6)
>> +#define ULPI_OTG_EXTVBUSIND (1 << 7)
>> +
>> +/*
>> + * USB Interrupt Enable Rising,
>> + * USB Interrupt Enable Falling,
>> + * USB Interrupt Status and
>> + * USB Interrupt Latch
>> + */
>> +#define ULPI_INT_HOST_DISCONNECT (1 << 0)
>> +#define ULPI_INT_VBUS_VALID (1 << 1)
>> +#define ULPI_INT_SESS_VALID (1 << 2)
>> +#define ULPI_INT_SESS_END (1 << 3)
>> +#define ULPI_INT_IDGRD (1 << 4)
>> +
>> +/* Debug */
>> +#define ULPI_DEBUG_LINESTATE0 (1 << 0)
>> +#define ULPI_DEBUG_LINESTATE1 (1 << 1)
>> +
>> +/* Carkit Control */
>> +#define ULPI_CARKIT_CTRL_CARKITPWR (1 << 0)
>> +#define ULPI_CARKIT_CTRL_IDGNDDRV (1 << 1)
>> +#define ULPI_CARKIT_CTRL_TXDEN (1 << 2)
>> +#define ULPI_CARKIT_CTRL_RXDEN (1 << 3)
>> +#define ULPI_CARKIT_CTRL_SPKLEFTEN (1 << 4)
>> +#define ULPI_CARKIT_CTRL_SPKRIGHTEN (1 << 5)
>> +#define ULPI_CARKIT_CTRL_MICEN (1 << 6)
>> +
>> +/* Carkit Interrupt Enable */
>> +#define ULPI_CARKIT_INT_EN_IDFLOAT_RISE (1 << 0)
>> +#define ULPI_CARKIT_INT_EN_IDFLOAT_FALL (1 << 1)
>> +#define ULPI_CARKIT_INT_EN_CARINTDET (1 << 2)
>> +#define ULPI_CARKIT_INT_EN_DP_RISE (1 << 3)
>> +#define ULPI_CARKIT_INT_EN_DP_FALL (1 << 4)
>> +
>> +/*
>> + * Carkit Interrupt Status and
>> + * Carkit Interrupt Latch
>> + */
>> +#define ULPI_CARKIT_INT_IDFLOAT (1 << 0)
>> +#define ULPI_CARKIT_INT_CARINTDET (1 << 1)
>> +#define ULPI_CARKIT_INT_DP (1 << 2)
>> +
>> +/* Carkit Pulse Control*/
>> +#define ULPI_CARKIT_PLS_CTRL_TXPLSEN (1 << 0)
>> +#define ULPI_CARKIT_PLS_CTRL_RXPLSEN (1 << 1)
>> +#define ULPI_CARKIT_PLS_CTRL_SPKRLEFT_BIASEN (1 << 2)
>> +#define ULPI_CARKIT_PLS_CTRL_SPKRRIGHT_BIASEN (1 << 3)
>> +
>> +void ulpi_write(u32 ulpi_viewport, u32 reg, u32 value);
>> +u32 ulpi_read(u32 ulpi_viewport, u32 reg);
>> +
>> +void ulpi_init(u32 ulpi_viewport, struct ulpi_regs *ulpi);
>
> Are there any ULPI transceivers with memory mapped access?
>
> Because if there are no such devices, then passing that
> struct ulpi_regs *ulpi pointer is redundant and it will
> always be 0.
>
> I think it will clearer _not_ to pass this pointer, but have it
> defined locally inside the ulpi.c. Any objections?
>
>> +
>> +void ulpi_otg_ctrl_flags(u32 ulpi_viewport,
>> + struct ulpi_regs *ulpi, int access_mode, u32 flags);
>> +void ulpi_function_ctrl_flags(u32 ulpi_viewport,
>> + struct ulpi_regs *ulpi, int access_mode, u32 flags);
>> +void ulpi_iface_ctrl_flags(u32 ulpi_viewport,
>> + struct ulpi_regs *ulpi, int access_mode, u32 flags);
>
> Once you have defined a functional API, I don't think there will
> be a need for these *_flags() functions.
>
>> +
>> +#endif /* __USB_ULPI_H */
>

--
Regards,
Igor.