[U-Boot] [PATCH 17/20] M28: Add memory detection into SPL

[Stefano Babic <sbabic@denx.de>]

On 11/09/2011 10:18 AM, Marek Vasut wrote:
> This code allows the DDR DRAM size to be detected at runtime. The RAM size is
> stored into two scratch registers, from which it is then fetched in U-Boot.
> 
> Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
> Cc: Stefano Babic <sbabic@denx.de>
> Cc: Wolfgang Denk <wd@denx.de>
> Cc: Detlev Zundel <dzu@denx.de>
> 
> ---
>  board/denx/m28evk/Makefile   |    7 ++++++-
>  board/denx/m28evk/m28evk.c   |   18 ++++++++++++++++--
>  board/denx/m28evk/mem_init.c |   27 +++++++++++++++++++++++++++
>  include/configs/m28evk.h     |    2 +-
>  4 files changed, 50 insertions(+), 4 deletions(-)
> 
> diff --git a/board/denx/m28evk/Makefile b/board/denx/m28evk/Makefile
> index 47229e6..b6f002f 100644
> --- a/board/denx/m28evk/Makefile
> +++ b/board/denx/m28evk/Makefile
> @@ -30,7 +30,7 @@ COBJS	:= m28evk.o
>  endif
>  
>  ifdef	CONFIG_SPL_BUILD
> -COBJS	:= mem_init.o mmc_boot.o power_init.o
> +COBJS	:= mem_init.o mmc_boot.o power_init.o memsize.o
>  endif
>  
>  SRCS	:= $(COBJS:.o=.c)
> @@ -41,6 +41,11 @@ $(LIB):	$(obj).depend $(OBJS)
>  
>  all:	$(ALL)
>  
> +ifdef	CONFIG_SPL_BUILD
> +memsize.c:
> +	ln -sf $(TOPDIR)/common/memsize.c $@
> +endif
> +
>  #########################################################################
>  
>  # defines $(obj).depend target
> diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
> index 118e222..168ceeb 100644
> --- a/board/denx/m28evk/m28evk.c
> +++ b/board/denx/m28evk/m28evk.c
> @@ -63,10 +63,24 @@ int board_init(void)
>  	return 0;
>  }
>  
> +#define	HW_DIGCTRL_SCRATCH0	0x8001c280
> +#define	HW_DIGCTRL_SCRATCH1	0x8001c290
>  int dram_init(void)
>  {
> -	/* dram_init must store complete ramsize in gd->ram_size */
> -	gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE);
> +	uint32_t sz[2];
> +
> +	sz[0] = readl(HW_DIGCTRL_SCRATCH0);
> +	sz[1] = readl(HW_DIGCTRL_SCRATCH1);
> +
> +	if (sz[0] != sz[1]) {
> +		printf("MX28:\n"
> +			"Error, the RAM size in HW_DIGCTRL_SCRATCH0 and\n"
> +			"HW_DIGCTRL_SCRATCH1 is not the same. Please\n"
> +			"verify these two registers contain valid RAM size!\n");
> +		hang();
> +	}
> +
> +	gd->ram_size = sz[0];
>  	return 0;
>  }
>  
> diff --git a/board/denx/m28evk/mem_init.c b/board/denx/m28evk/mem_init.c
> index 066fe0d..17d1f9b 100644
> --- a/board/denx/m28evk/mem_init.c
> +++ b/board/denx/m28evk/mem_init.c
> @@ -165,6 +165,31 @@ void mx28_mem_setup_vddd(void)
>  		&power_regs->hw_power_vdddctrl);
>  }
>  
> +#define	HW_DIGCTRL_SCRATCH0	0x8001c280
> +#define	HW_DIGCTRL_SCRATCH1	0x8001c290
> +void data_abort_memdetect_handler(void) __attribute__((naked));
> +void data_abort_memdetect_handler(void)
> +{
> +	asm volatile("subs pc, r14, #4");
> +}
> +
> +void mx28_mem_get_size(void)
> +{
> +	uint32_t sz, da;
> +	uint32_t *vt = (uint32_t *)0x20;
> +
> +	/* Replace the DABT handler. */
> +	da = vt[4];
> +	vt[4] = (uint32_t)&data_abort_memdetect_handler;
> +
> +	sz = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE);
> +	writel(sz, HW_DIGCTRL_SCRATCH0);
> +	writel(sz, HW_DIGCTRL_SCRATCH1);
> +
> +	/* Restore the old DABT handler. */
> +	vt[4] = da;
> +}
> +
>  void mx28_mem_init(void)
>  {
>  	struct mx28_clkctrl_regs *clkctrl_regs =
> @@ -210,4 +235,6 @@ void mx28_mem_init(void)
>  	early_delay(10000);
>  
>  	mx28_mem_setup_cpu_and_hbus();
> +
> +	mx28_mem_get_size();
>  }
> diff --git a/include/configs/m28evk.h b/include/configs/m28evk.h
> index 381b01e..c8b0cf5 100644
> --- a/include/configs/m28evk.h
> +++ b/include/configs/m28evk.h
> @@ -81,7 +81,7 @@
>   */
>  #define	CONFIG_NR_DRAM_BANKS		1		/* 2 banks of DRAM */
>  #define	PHYS_SDRAM_1			0x40000000	/* Base address */
> -#define	PHYS_SDRAM_1_SIZE		0x08000000	/* 128 MB */
> +#define	PHYS_SDRAM_1_SIZE		0x40000000	/* Max 1 GB RAM */
>  #define	CONFIG_STACKSIZE		0x00010000	/* 128 KB stack */
>  #define	CONFIG_SYS_MALLOC_LEN		0x00400000	/* 4 MB for malloc */
>  #define	CONFIG_SYS_GBL_DATA_SIZE	128		/* Initial data */

Applied to u-boot-imx, thanks.

Best regards,
Stefano Babic


-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================