* [U-Boot] [PATCH v7 2/4] tegra2: Move board_mmc_init into board files
2011-10-31 16:51 [U-Boot] [PATCH v7 1/4] tegra2: Move MMC clock initialization into MMC driver Stephen Warren
@ 2011-10-31 16:51 ` Stephen Warren
2011-10-31 16:51 ` [U-Boot] [PATCH v7 3/4] tegra2: Modify MMC driver to handle power and cd GPIOs Stephen Warren
` (2 subsequent siblings)
3 siblings, 0 replies; 7+ messages in thread
From: Stephen Warren @ 2011-10-31 16:51 UTC (permalink / raw)
To: u-boot
For Seaboard, this is mostly a cut/paste of board_mmc_init() and
pin_mux_mmc() into seaboard.c; pin_mux_mmc() was modified to add some
missing pinmux_tristate_disable calls for the GPIOs.
For Harmony, those functions were modified to configure SDMMC2 (index 2)
instead of SDMMC3 (index 1), since that's what is present on the board.
However, harmony.c is still missing the required GPIO setup, so neither
port is likely to function correctly yet. This will be fixed in the next
change.
v4: Include board.h to prototype tegra2_mmc_init().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
---
board/nvidia/common/board.c | 52 -----------------------------------
board/nvidia/harmony/harmony.c | 56 ++++++++++++++++++++++++++++++++++++++
board/nvidia/seaboard/seaboard.c | 53 +++++++++++++++++++++++++++++++++++
3 files changed, 109 insertions(+), 52 deletions(-)
diff --git a/board/nvidia/common/board.c b/board/nvidia/common/board.c
index 370a259..0f12de2 100644
--- a/board/nvidia/common/board.c
+++ b/board/nvidia/common/board.c
@@ -33,10 +33,6 @@
#include <asm/arch/uart.h>
#include "board.h"
-#ifdef CONFIG_TEGRA2_MMC
-#include <mmc.h>
-#endif
-
DECLARE_GLOBAL_DATA_PTR;
const struct tegra2_sysinfo sysinfo = {
@@ -100,33 +96,6 @@ static void pin_mux_uart(void)
#endif /* CONFIG_TEGRA2_ENABLE_UARTD */
}
-#ifdef CONFIG_TEGRA2_MMC
-/*
- * Routine: pin_mux_mmc
- * Description: setup the pin muxes/tristate values for the SDMMC(s)
- */
-static void pin_mux_mmc(void)
-{
- /* SDMMC4: config 3, x8 on 2nd set of pins */
- pinmux_set_func(PINGRP_ATB, PMUX_FUNC_SDIO4);
- pinmux_set_func(PINGRP_GMA, PMUX_FUNC_SDIO4);
- pinmux_set_func(PINGRP_GME, PMUX_FUNC_SDIO4);
-
- pinmux_tristate_disable(PINGRP_ATB);
- pinmux_tristate_disable(PINGRP_GMA);
- pinmux_tristate_disable(PINGRP_GME);
-
- /* SDMMC3: SDIO3_CLK, SDIO3_CMD, SDIO3_DAT[3:0] */
- pinmux_set_func(PINGRP_SDB, PMUX_FUNC_SDIO3);
- pinmux_set_func(PINGRP_SDC, PMUX_FUNC_SDIO3);
- pinmux_set_func(PINGRP_SDD, PMUX_FUNC_SDIO3);
-
- pinmux_tristate_disable(PINGRP_SDC);
- pinmux_tristate_disable(PINGRP_SDD);
- pinmux_tristate_disable(PINGRP_SDB);
-}
-#endif
-
/*
* Routine: board_init
* Description: Early hardware init.
@@ -142,27 +111,6 @@ int board_init(void)
return 0;
}
-#ifdef CONFIG_TEGRA2_MMC
-/* this is a weak define that we are overriding */
-int board_mmc_init(bd_t *bd)
-{
- debug("board_mmc_init called\n");
- /* Enable muxes, etc. for SDMMC controllers */
- pin_mux_mmc();
- gpio_config_mmc();
-
- debug("board_mmc_init: init eMMC\n");
- /* init dev 0, eMMC chip, with 4-bit bus */
- tegra2_mmc_init(0, 4);
-
- debug("board_mmc_init: init SD slot\n");
- /* init dev 1, SD slot, with 4-bit bus */
- tegra2_mmc_init(1, 4);
-
- return 0;
-}
-#endif
-
#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
diff --git a/board/nvidia/harmony/harmony.c b/board/nvidia/harmony/harmony.c
index cbb30d6..f2c3867 100644
--- a/board/nvidia/harmony/harmony.c
+++ b/board/nvidia/harmony/harmony.c
@@ -24,9 +24,11 @@
#include <common.h>
#include <asm/io.h>
#include <asm/arch/tegra2.h>
+#include <asm/arch/pinmux.h>
#ifdef CONFIG_TEGRA2_MMC
#include <mmc.h>
#endif
+#include "../common/board.h"
/*
* Routine: gpio_config_uart
@@ -38,6 +40,39 @@ void gpio_config_uart(void)
#ifdef CONFIG_TEGRA2_MMC
/*
+ * Routine: pin_mux_mmc
+ * Description: setup the pin muxes/tristate values for the SDMMC(s)
+ */
+static void pin_mux_mmc(void)
+{
+ /* SDMMC4: config 3, x8 on 2nd set of pins */
+ pinmux_set_func(PINGRP_ATB, PMUX_FUNC_SDIO4);
+ pinmux_set_func(PINGRP_GMA, PMUX_FUNC_SDIO4);
+ pinmux_set_func(PINGRP_GME, PMUX_FUNC_SDIO4);
+
+ pinmux_tristate_disable(PINGRP_ATB);
+ pinmux_tristate_disable(PINGRP_GMA);
+ pinmux_tristate_disable(PINGRP_GME);
+
+ /* For power GPIO PI6 */
+ pinmux_tristate_disable(PINGRP_ATA);
+ /* For CD GPIO PH2 */
+ pinmux_tristate_disable(PINGRP_ATD);
+
+ /* SDMMC2: SDIO2_CLK, SDIO2_CMD, SDIO2_DAT[7:0] */
+ pinmux_set_func(PINGRP_DTA, PMUX_FUNC_SDIO2);
+ pinmux_set_func(PINGRP_DTD, PMUX_FUNC_SDIO2);
+
+ pinmux_tristate_disable(PINGRP_DTA);
+ pinmux_tristate_disable(PINGRP_DTD);
+
+ /* For power GPIO PT3 */
+ pinmux_tristate_disable(PINGRP_DTB);
+ /* For CD GPIO PI5 */
+ pinmux_tristate_disable(PINGRP_ATC);
+}
+
+/*
* Routine: gpio_config_mmc
* Description: Set GPIOs for SD card
*/
@@ -47,6 +82,27 @@ void gpio_config_mmc(void)
}
/* this is a weak define that we are overriding */
+int board_mmc_init(bd_t *bd)
+{
+ debug("board_mmc_init called\n");
+
+ /* Enable muxes, etc. for SDMMC controllers */
+ pin_mux_mmc();
+ gpio_config_mmc();
+
+ debug("board_mmc_init: init SD slot J26\n");
+ /* init dev 0, SD slot J26, with 4-bit bus */
+ /* The board has an 8-bit bus, but 8-bit doesn't work yet */
+ tegra2_mmc_init(0, 4);
+
+ debug("board_mmc_init: init SD slot J5\n");
+ /* init dev 2, SD slot J5, with 4-bit bus */
+ tegra2_mmc_init(2, 4);
+
+ return 0;
+}
+
+/* this is a weak define that we are overriding */
int board_mmc_getcd(u8 *cd, struct mmc *mmc)
{
debug("board_mmc_getcd called\n");
diff --git a/board/nvidia/seaboard/seaboard.c b/board/nvidia/seaboard/seaboard.c
index bc67d0f..22a0e69 100644
--- a/board/nvidia/seaboard/seaboard.c
+++ b/board/nvidia/seaboard/seaboard.c
@@ -24,10 +24,12 @@
#include <common.h>
#include <asm/io.h>
#include <asm/arch/tegra2.h>
+#include <asm/arch/pinmux.h>
#include <asm/gpio.h>
#ifdef CONFIG_TEGRA2_MMC
#include <mmc.h>
#endif
+#include "../common/board.h"
/*
* Routine: gpio_config_uart
@@ -56,6 +58,36 @@ void gpio_config_uart(void)
#ifdef CONFIG_TEGRA2_MMC
/*
+ * Routine: pin_mux_mmc
+ * Description: setup the pin muxes/tristate values for the SDMMC(s)
+ */
+static void pin_mux_mmc(void)
+{
+ /* SDMMC4: config 3, x8 on 2nd set of pins */
+ pinmux_set_func(PINGRP_ATB, PMUX_FUNC_SDIO4);
+ pinmux_set_func(PINGRP_GMA, PMUX_FUNC_SDIO4);
+ pinmux_set_func(PINGRP_GME, PMUX_FUNC_SDIO4);
+
+ pinmux_tristate_disable(PINGRP_ATB);
+ pinmux_tristate_disable(PINGRP_GMA);
+ pinmux_tristate_disable(PINGRP_GME);
+
+ /* SDMMC3: SDIO3_CLK, SDIO3_CMD, SDIO3_DAT[3:0] */
+ pinmux_set_func(PINGRP_SDB, PMUX_FUNC_SDIO3);
+ pinmux_set_func(PINGRP_SDC, PMUX_FUNC_SDIO3);
+ pinmux_set_func(PINGRP_SDD, PMUX_FUNC_SDIO3);
+
+ pinmux_tristate_disable(PINGRP_SDC);
+ pinmux_tristate_disable(PINGRP_SDD);
+ pinmux_tristate_disable(PINGRP_SDB);
+
+ /* For power GPIO PI6 */
+ pinmux_tristate_disable(PINGRP_ATA);
+ /* For CD GPIO PI5 */
+ pinmux_tristate_disable(PINGRP_ATC);
+}
+
+/*
* Routine: gpio_config_mmc
* Description: Set GPIOs for SDMMC3 SDIO slot.
*/
@@ -69,6 +101,27 @@ void gpio_config_mmc(void)
}
/* this is a weak define that we are overriding */
+int board_mmc_init(bd_t *bd)
+{
+ debug("board_mmc_init called\n");
+
+ /* Enable muxes, etc. for SDMMC controllers */
+ pin_mux_mmc();
+ gpio_config_mmc();
+
+ debug("board_mmc_init: init eMMC\n");
+ /* init dev 0, eMMC chip, with 4-bit bus */
+ /* The board has an 8-bit bus, but 8-bit doesn't work yet */
+ tegra2_mmc_init(0, 4);
+
+ debug("board_mmc_init: init SD slot\n");
+ /* init dev 1, SD slot, with 4-bit bus */
+ tegra2_mmc_init(1, 4);
+
+ return 0;
+}
+
+/* this is a weak define that we are overriding */
int board_mmc_getcd(u8 *cd, struct mmc *mmc)
{
debug("board_mmc_getcd called\n");
--
1.7.0.4
^ permalink raw reply related [flat|nested] 7+ messages in thread* [U-Boot] [PATCH v7 3/4] tegra2: Modify MMC driver to handle power and cd GPIOs
2011-10-31 16:51 [U-Boot] [PATCH v7 1/4] tegra2: Move MMC clock initialization into MMC driver Stephen Warren
2011-10-31 16:51 ` [U-Boot] [PATCH v7 2/4] tegra2: Move board_mmc_init into board files Stephen Warren
@ 2011-10-31 16:51 ` Stephen Warren
2011-11-03 2:30 ` Andy Fleming
2011-10-31 16:51 ` [U-Boot] [PATCH v7 4/4] tegra2: Add support for Ventana Stephen Warren
2011-10-31 18:08 ` [U-Boot] [PATCH v7 1/4] tegra2: Move MMC clock initialization into MMC driver Simon Glass
3 siblings, 1 reply; 7+ messages in thread
From: Stephen Warren @ 2011-10-31 16:51 UTC (permalink / raw)
To: u-boot
Pass the GPIO numbers for power and card detect to tegra2_mmc_init(), and
modify that function to perform all required GPIO initialization. This
removes the need for board files to perform these operations.
Move board_mmc_getcd() into tegra2_mmc.c now that the driver knows which
GPIOs to use.
Update affected call-sites in seaboard.c and harmony.c. Note that this
change should make all SD ports work on Harmony, since the required GPIO
setup is now being performed.
v4: Fix prototype of tegra2_mmc_init() in board.h to match driver change.
Remove prototype of gpio_config_mmc() from board.h
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Andy Fleming <afleming@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
---
board/nvidia/common/board.h | 3 +-
board/nvidia/harmony/harmony.c | 27 ++---------------------
board/nvidia/seaboard/seaboard.c | 33 +----------------------------
drivers/mmc/tegra2_mmc.c | 42 ++++++++++++++++++++++++++++++++-----
drivers/mmc/tegra2_mmc.h | 4 ++-
5 files changed, 45 insertions(+), 64 deletions(-)
diff --git a/board/nvidia/common/board.h b/board/nvidia/common/board.h
index 344e702..35acbca 100644
--- a/board/nvidia/common/board.h
+++ b/board/nvidia/common/board.h
@@ -26,7 +26,6 @@
void tegra2_start(void);
void gpio_config_uart(void);
-void gpio_config_mmc(void);
-int tegra2_mmc_init(int dev_index, int bus_width);
+int tegra2_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio);
#endif /* BOARD_H */
diff --git a/board/nvidia/harmony/harmony.c b/board/nvidia/harmony/harmony.c
index f2c3867..3cbe820 100644
--- a/board/nvidia/harmony/harmony.c
+++ b/board/nvidia/harmony/harmony.c
@@ -25,6 +25,7 @@
#include <asm/io.h>
#include <asm/arch/tegra2.h>
#include <asm/arch/pinmux.h>
+#include <asm/gpio.h>
#ifdef CONFIG_TEGRA2_MMC
#include <mmc.h>
#endif
@@ -72,15 +73,6 @@ static void pin_mux_mmc(void)
pinmux_tristate_disable(PINGRP_ATC);
}
-/*
- * Routine: gpio_config_mmc
- * Description: Set GPIOs for SD card
- */
-void gpio_config_mmc(void)
-{
- /* Not implemented for now */
-}
-
/* this is a weak define that we are overriding */
int board_mmc_init(bd_t *bd)
{
@@ -88,29 +80,16 @@ int board_mmc_init(bd_t *bd)
/* Enable muxes, etc. for SDMMC controllers */
pin_mux_mmc();
- gpio_config_mmc();
debug("board_mmc_init: init SD slot J26\n");
/* init dev 0, SD slot J26, with 4-bit bus */
/* The board has an 8-bit bus, but 8-bit doesn't work yet */
- tegra2_mmc_init(0, 4);
+ tegra2_mmc_init(0, 4, GPIO_PI6, GPIO_PH2);
debug("board_mmc_init: init SD slot J5\n");
/* init dev 2, SD slot J5, with 4-bit bus */
- tegra2_mmc_init(2, 4);
+ tegra2_mmc_init(2, 4, GPIO_PT3, GPIO_PI5);
return 0;
}
-
-/* this is a weak define that we are overriding */
-int board_mmc_getcd(u8 *cd, struct mmc *mmc)
-{
- debug("board_mmc_getcd called\n");
- /*
- * Hard-code CD presence for now. Need to add GPIO inputs
- * for Harmony
- */
- *cd = 1;
- return 0;
-}
#endif
diff --git a/board/nvidia/seaboard/seaboard.c b/board/nvidia/seaboard/seaboard.c
index 22a0e69..356d616 100644
--- a/board/nvidia/seaboard/seaboard.c
+++ b/board/nvidia/seaboard/seaboard.c
@@ -87,19 +87,6 @@ static void pin_mux_mmc(void)
pinmux_tristate_disable(PINGRP_ATC);
}
-/*
- * Routine: gpio_config_mmc
- * Description: Set GPIOs for SDMMC3 SDIO slot.
- */
-void gpio_config_mmc(void)
-{
- /* Set EN_VDDIO_SD (GPIO I6) */
- gpio_direction_output(GPIO_PI6, 1);
-
- /* Config pin as GPI for Card Detect (GPIO I5) */
- gpio_direction_input(GPIO_PI5);
-}
-
/* this is a weak define that we are overriding */
int board_mmc_init(bd_t *bd)
{
@@ -107,31 +94,15 @@ int board_mmc_init(bd_t *bd)
/* Enable muxes, etc. for SDMMC controllers */
pin_mux_mmc();
- gpio_config_mmc();
debug("board_mmc_init: init eMMC\n");
/* init dev 0, eMMC chip, with 4-bit bus */
/* The board has an 8-bit bus, but 8-bit doesn't work yet */
- tegra2_mmc_init(0, 4);
+ tegra2_mmc_init(0, 4, -1, -1);
debug("board_mmc_init: init SD slot\n");
/* init dev 1, SD slot, with 4-bit bus */
- tegra2_mmc_init(1, 4);
-
- return 0;
-}
-
-/* this is a weak define that we are overriding */
-int board_mmc_getcd(u8 *cd, struct mmc *mmc)
-{
- debug("board_mmc_getcd called\n");
- *cd = 1; /* Assume card is inserted, or eMMC */
-
- if (IS_SD(mmc)) {
- /* Seaboard SDMMC3 = SDIO3_CD = GPIO_PI5 */
- if (gpio_get_value(GPIO_PI5))
- *cd = 0;
- }
+ tegra2_mmc_init(1, 4, GPIO_PI6, GPIO_PI5);
return 0;
}
diff --git a/drivers/mmc/tegra2_mmc.c b/drivers/mmc/tegra2_mmc.c
index 78b1190..3de9c5d 100644
--- a/drivers/mmc/tegra2_mmc.c
+++ b/drivers/mmc/tegra2_mmc.c
@@ -21,6 +21,7 @@
#include <common.h>
#include <mmc.h>
+#include <asm/gpio.h>
#include <asm/io.h>
#include <asm/arch/clk_rst.h>
#include <asm/arch/clock.h>
@@ -433,20 +434,37 @@ static int mmc_core_init(struct mmc *mmc)
return 0;
}
-static int tegra2_mmc_initialize(int dev_index, int bus_width)
+int tegra2_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio)
{
struct mmc_host *host;
+ char gpusage[12]; /* "SD/MMCn PWR" or "SD/MMCn CD" */
struct mmc *mmc;
- debug(" mmc_initialize called\n");
+ debug(" tegra2_mmc_init: index %d, bus width %d "
+ "pwr_gpio %d cd_gpio %d\n",
+ dev_index, bus_width, pwr_gpio, cd_gpio);
host = &mmc_host[dev_index];
host->clock = 0;
+ host->pwr_gpio = pwr_gpio;
+ host->cd_gpio = cd_gpio;
tegra2_get_setup(host, dev_index);
clock_start_periph_pll(host->mmc_id, CLOCK_ID_PERIPH, 20000000);
+ if (host->pwr_gpio >= 0) {
+ sprintf(gpusage, "SD/MMC%d PWR", dev_index);
+ gpio_request(host->pwr_gpio, gpusage);
+ gpio_direction_output(host->pwr_gpio, 1);
+ }
+
+ if (host->cd_gpio >= 0) {
+ sprintf(gpusage, "SD/MMC%d CD", dev_index);
+ gpio_request(host->cd_gpio, gpusage);
+ gpio_direction_input(host->cd_gpio);
+ }
+
mmc = &mmc_dev[dev_index];
sprintf(mmc->name, "Tegra2 SD/MMC");
@@ -478,9 +496,21 @@ static int tegra2_mmc_initialize(int dev_index, int bus_width)
return 0;
}
-int tegra2_mmc_init(int dev_index, int bus_width)
+/* this is a weak define that we are overriding */
+int board_mmc_getcd(u8 *cd, struct mmc *mmc)
{
- debug(" tegra2_mmc_init: index %d, bus width %d\n",
- dev_index, bus_width);
- return tegra2_mmc_initialize(dev_index, bus_width);
+ struct mmc_host *host = (struct mmc_host *)mmc->priv;
+
+ debug("board_mmc_getcd called\n");
+
+ *cd = 1; /* Assume card is inserted, or eMMC */
+
+ if (IS_SD(mmc)) {
+ if (host->cd_gpio >= 0) {
+ if (gpio_get_value(host->cd_gpio))
+ *cd = 0;
+ }
+ }
+
+ return 0;
}
diff --git a/drivers/mmc/tegra2_mmc.h b/drivers/mmc/tegra2_mmc.h
index 28698e0..72f587b 100644
--- a/drivers/mmc/tegra2_mmc.h
+++ b/drivers/mmc/tegra2_mmc.h
@@ -74,9 +74,11 @@ struct mmc_host {
unsigned int clock; /* Current clock (MHz) */
unsigned int base; /* Base address, SDMMC1/2/3/4 */
enum periph_id mmc_id; /* Peripheral ID: PERIPH_ID_... */
+ int pwr_gpio; /* Power GPIO */
+ int cd_gpio; /* Change Detect GPIO */
};
-int tegra2_mmc_init(int dev_index, int bus_width);
+int tegra2_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio);
#endif /* __ASSEMBLY__ */
#endif /* __TEGRA2_MMC_H_ */
--
1.7.0.4
^ permalink raw reply related [flat|nested] 7+ messages in thread* [U-Boot] [PATCH v7 3/4] tegra2: Modify MMC driver to handle power and cd GPIOs
2011-10-31 16:51 ` [U-Boot] [PATCH v7 3/4] tegra2: Modify MMC driver to handle power and cd GPIOs Stephen Warren
@ 2011-11-03 2:30 ` Andy Fleming
2011-11-15 21:51 ` Stephen Warren
0 siblings, 1 reply; 7+ messages in thread
From: Andy Fleming @ 2011-11-03 2:30 UTC (permalink / raw)
To: u-boot
On Mon, Oct 31, 2011 at 11:51 AM, Stephen Warren <swarren@nvidia.com> wrote:
> Pass the GPIO numbers for power and card detect to tegra2_mmc_init(), and
> modify that function to perform all required GPIO initialization. This
> removes the need for board files to perform these operations.
>
> Move board_mmc_getcd() into tegra2_mmc.c now that the driver knows which
> GPIOs to use.
>
> Update affected call-sites in seaboard.c and harmony.c. Note that this
> change should make all SD ports work on Harmony, since the required GPIO
> setup is now being performed.
>
> v4: Fix prototype of tegra2_mmc_init() in board.h to match driver change.
> ? ?Remove prototype of gpio_config_mmc() from board.h
>
> Signed-off-by: Stephen Warren <swarren@nvidia.com>
> Cc: Andy Fleming <afleming@gmail.com>
> Tested-by: Simon Glass <sjg@chromium.org>
> Acked-by: Simon Glass <sjg@chromium.org>
This patch depends heavily on patch #2 (ie, won't apply without it),
which doesn't touch drivers/mmc.
Lacking an ACK from Albert, I hesitate to just apply the whole series.
I've applied patch #1, and I'll let Albert decide whether to apply the
other 3:
Acked-by: Andy Fleming <afleming@freescale.com>
I have also re-assigned this patch in patchworks to Albert.
^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH v7 3/4] tegra2: Modify MMC driver to handle power and cd GPIOs
2011-11-03 2:30 ` Andy Fleming
@ 2011-11-15 21:51 ` Stephen Warren
0 siblings, 0 replies; 7+ messages in thread
From: Stephen Warren @ 2011-11-15 21:51 UTC (permalink / raw)
To: u-boot
On 11/02/2011 08:30 PM, Andy Fleming wrote:
> On Mon, Oct 31, 2011 at 11:51 AM, Stephen Warren <swarren@nvidia.com> wrote:
>> Pass the GPIO numbers for power and card detect to tegra2_mmc_init(), and
>> modify that function to perform all required GPIO initialization. This
>> removes the need for board files to perform these operations.
>>
>> Move board_mmc_getcd() into tegra2_mmc.c now that the driver knows which
>> GPIOs to use.
>>
>> Update affected call-sites in seaboard.c and harmony.c. Note that this
>> change should make all SD ports work on Harmony, since the required GPIO
>> setup is now being performed.
>>
>> v4: Fix prototype of tegra2_mmc_init() in board.h to match driver change.
>> Remove prototype of gpio_config_mmc() from board.h
>>
>> Signed-off-by: Stephen Warren <swarren@nvidia.com>
>> Cc: Andy Fleming <afleming@gmail.com>
>> Tested-by: Simon Glass <sjg@chromium.org>
>> Acked-by: Simon Glass <sjg@chromium.org>
>
> This patch depends heavily on patch #2 (ie, won't apply without it),
> which doesn't touch drivers/mmc.
>
> Lacking an ACK from Albert, I hesitate to just apply the whole series.
> I've applied patch #1, and I'll let Albert decide whether to apply the
> other 3:
>
> Acked-by: Andy Fleming <afleming@freescale.com>
>
> I have also re-assigned this patch in patchworks to Albert.
Albert, Do the remaining 3 patches in this series look good?
Thanks.
--
nvpublic
^ permalink raw reply [flat|nested] 7+ messages in thread
* [U-Boot] [PATCH v7 4/4] tegra2: Add support for Ventana
2011-10-31 16:51 [U-Boot] [PATCH v7 1/4] tegra2: Move MMC clock initialization into MMC driver Stephen Warren
2011-10-31 16:51 ` [U-Boot] [PATCH v7 2/4] tegra2: Move board_mmc_init into board files Stephen Warren
2011-10-31 16:51 ` [U-Boot] [PATCH v7 3/4] tegra2: Modify MMC driver to handle power and cd GPIOs Stephen Warren
@ 2011-10-31 16:51 ` Stephen Warren
2011-10-31 18:08 ` [U-Boot] [PATCH v7 1/4] tegra2: Move MMC clock initialization into MMC driver Simon Glass
3 siblings, 0 replies; 7+ messages in thread
From: Stephen Warren @ 2011-10-31 16:51 UTC (permalink / raw)
To: u-boot
Ventana is a board which is very similar to Seaboard. Support it by
re-using board/nvidia/seaboard/seaboard.c with minor run-time conditionals.
v5: Makefile: Use cmd_link_o_target, remove unused clean/distclean targets.
v6: Make gpio_config_uart_seaboard() static.
v7: Add MAINTAINERS entry for Ventana. Tom Warren doesn't have Ventana, so
he asked me to add myself for this board.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
---
MAINTAINERS | 5 +++
board/nvidia/seaboard/seaboard.c | 11 ++++++-
board/nvidia/ventana/Makefile | 49 +++++++++++++++++++++++++++++++++
boards.cfg | 1 +
include/configs/ventana.h | 55 ++++++++++++++++++++++++++++++++++++++
5 files changed, 119 insertions(+), 2 deletions(-)
create mode 100644 board/nvidia/ventana/Makefile
create mode 100644 include/configs/ventana.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 576fea8..6ff894c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -873,6 +873,11 @@ Tom Warren <twarren@nvidia.com>
harmony Tegra2 (ARM7 & A9 Dual Core)
seaboard Tegra2 (ARM7 & A9 Dual Core)
+Tom Warren <twarren@nvidia.com>
+Stephen Warren <twarren@nvidia.com>
+
+ ventana Tegra2 (ARM7 & A9 Dual Core)
+
Lei Wen <leiwen@marvell.com>
dkb ARM926EJS (PANTHEON 88AP920 SOC)
diff --git a/board/nvidia/seaboard/seaboard.c b/board/nvidia/seaboard/seaboard.c
index 356d616..aa77f12 100644
--- a/board/nvidia/seaboard/seaboard.c
+++ b/board/nvidia/seaboard/seaboard.c
@@ -32,10 +32,10 @@
#include "../common/board.h"
/*
- * Routine: gpio_config_uart
+ * Routine: gpio_config_uart_seaboard
* Description: Force GPIO_PI3 low on Seaboard so UART4 works.
*/
-void gpio_config_uart(void)
+static void gpio_config_uart_seaboard(void)
{
int gp = GPIO_PI3;
struct gpio_ctlr *gpio = (struct gpio_ctlr *)NV_PA_GPIO_BASE;
@@ -56,6 +56,13 @@ void gpio_config_uart(void)
writel(val, &bank->gpio_dir_out[GPIO_PORT(gp)]);
}
+void gpio_config_uart(void)
+{
+ if (machine_is_ventana())
+ return;
+ gpio_config_uart_seaboard();
+}
+
#ifdef CONFIG_TEGRA2_MMC
/*
* Routine: pin_mux_mmc
diff --git a/board/nvidia/ventana/Makefile b/board/nvidia/ventana/Makefile
new file mode 100644
index 0000000..9e5a87f
--- /dev/null
+++ b/board/nvidia/ventana/Makefile
@@ -0,0 +1,49 @@
+#
+# (C) Copyright 2010,2011
+# NVIDIA Corporation <www.nvidia.com>
+#
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+ifneq ($(OBJTREE),$(SRCTREE))
+$(shell mkdir -p $(obj)../common)
+endif
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS += ../seaboard/seaboard.o
+COBJS += ../common/board.o
+
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/boards.cfg b/boards.cfg
index 604becf..83a0039 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -194,6 +194,7 @@ s5pc210_universal arm armv7 universal_c210 samsung
smdkv310 arm armv7 smdkv310 samsung s5pc2xx
harmony arm armv7 harmony nvidia tegra2
seaboard arm armv7 seaboard nvidia tegra2
+ventana arm armv7 ventana nvidia tegra2
u8500_href arm armv7 u8500 st-ericsson u8500
actux1_4_16 arm ixp actux1 - - actux1:FLASH2X2
actux1_8_16 arm ixp actux1 - - actux1:FLASH1X8
diff --git a/include/configs/ventana.h b/include/configs/ventana.h
new file mode 100644
index 0000000..afd6ff6
--- /dev/null
+++ b/include/configs/ventana.h
@@ -0,0 +1,55 @@
+/*
+ * (C) Copyright 2010,2011
+ * NVIDIA Corporation <www.nvidia.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/sizes.h>
+#include "tegra2-common.h"
+
+/* High-level configuration options */
+#define TEGRA2_SYSMEM "mem=384M at 0M nvmem=128M at 384M mem=512M at 512M"
+#define V_PROMPT "Tegra2 (Ventana) # "
+#define CONFIG_TEGRA2_BOARD_STRING "NVIDIA Ventana"
+
+/* Board-specific serial config */
+#define CONFIG_SERIAL_MULTI
+#define CONFIG_TEGRA2_ENABLE_UARTD
+#define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTD_BASE
+
+#define CONFIG_MACH_TYPE MACH_TYPE_VENTANA
+#define CONFIG_SYS_BOARD_ODMDATA 0x300d8011 /* lp1, 1GB */
+
+#define CONFIG_BOARD_EARLY_INIT_F
+
+/* SD/MMC */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_TEGRA2_MMC
+#define CONFIG_CMD_MMC
+
+#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#endif /* __CONFIG_H */
--
1.7.0.4
^ permalink raw reply related [flat|nested] 7+ messages in thread* [U-Boot] [PATCH v7 1/4] tegra2: Move MMC clock initialization into MMC driver
2011-10-31 16:51 [U-Boot] [PATCH v7 1/4] tegra2: Move MMC clock initialization into MMC driver Stephen Warren
` (2 preceding siblings ...)
2011-10-31 16:51 ` [U-Boot] [PATCH v7 4/4] tegra2: Add support for Ventana Stephen Warren
@ 2011-10-31 18:08 ` Simon Glass
3 siblings, 0 replies; 7+ messages in thread
From: Simon Glass @ 2011-10-31 18:08 UTC (permalink / raw)
To: u-boot
Hi Stephen,
On Mon, Oct 31, 2011 at 9:51 AM, Stephen Warren <swarren@nvidia.com> wrote:
> This centralizes knowledge of MMC clocking into the MMC driver. This also
> removes clock setup from the board files, which will simplify later changes
> that modify the Harmony board to support the correct set of MMC controllers.
>
> Signed-off-by: Stephen Warren <swarren@nvidia.com>
> Cc: Andy Fleming <afleming@gmail.com>
> Acked-by: Simon Glass <sjg@chromium.org>
> Tested-by: Simon Glass <sjg@chromium.org>
I retested this new patch series with the latest master (mmc part,
ext2ls and ext2load) and it is fine.
Regards,
Simon
> ---
> ?board/nvidia/common/board.c | ? 13 +------------
> ?drivers/mmc/tegra2_mmc.c ? ?| ? 12 +++++++++---
> ?2 files changed, 10 insertions(+), 15 deletions(-)
>
> diff --git a/board/nvidia/common/board.c b/board/nvidia/common/board.c
> index d13537d..370a259 100644
> --- a/board/nvidia/common/board.c
> +++ b/board/nvidia/common/board.c
> @@ -102,16 +102,6 @@ static void pin_mux_uart(void)
>
> ?#ifdef CONFIG_TEGRA2_MMC
> ?/*
> - * Routine: clock_init_mmc
> - * Description: init the PLL and clocks for the SDMMC controllers
> - */
> -static void clock_init_mmc(void)
> -{
> - ? ? ? clock_start_periph_pll(PERIPH_ID_SDMMC4, CLOCK_ID_PERIPH, 20000000);
> - ? ? ? clock_start_periph_pll(PERIPH_ID_SDMMC3, CLOCK_ID_PERIPH, 20000000);
> -}
> -
> -/*
> ?* Routine: pin_mux_mmc
> ?* Description: setup the pin muxes/tristate values for the SDMMC(s)
> ?*/
> @@ -157,8 +147,7 @@ int board_init(void)
> ?int board_mmc_init(bd_t *bd)
> ?{
> ? ? ? ?debug("board_mmc_init called\n");
> - ? ? ? /* Enable clocks, muxes, etc. for SDMMC controllers */
> - ? ? ? clock_init_mmc();
> + ? ? ? /* Enable muxes, etc. for SDMMC controllers */
> ? ? ? ?pin_mux_mmc();
> ? ? ? ?gpio_config_mmc();
>
> diff --git a/drivers/mmc/tegra2_mmc.c b/drivers/mmc/tegra2_mmc.c
> index 9e741f2..78b1190 100644
> --- a/drivers/mmc/tegra2_mmc.c
> +++ b/drivers/mmc/tegra2_mmc.c
> @@ -435,14 +435,22 @@ static int mmc_core_init(struct mmc *mmc)
>
> ?static int tegra2_mmc_initialize(int dev_index, int bus_width)
> ?{
> + ? ? ? struct mmc_host *host;
> ? ? ? ?struct mmc *mmc;
>
> ? ? ? ?debug(" mmc_initialize called\n");
>
> + ? ? ? host = &mmc_host[dev_index];
> +
> + ? ? ? host->clock = 0;
> + ? ? ? tegra2_get_setup(host, dev_index);
> +
> + ? ? ? clock_start_periph_pll(host->mmc_id, CLOCK_ID_PERIPH, 20000000);
> +
> ? ? ? ?mmc = &mmc_dev[dev_index];
>
> ? ? ? ?sprintf(mmc->name, "Tegra2 SD/MMC");
> - ? ? ? mmc->priv = &mmc_host[dev_index];
> + ? ? ? mmc->priv = host;
> ? ? ? ?mmc->send_cmd = mmc_send_cmd;
> ? ? ? ?mmc->set_ios = mmc_set_ios;
> ? ? ? ?mmc->init = mmc_core_init;
> @@ -465,8 +473,6 @@ static int tegra2_mmc_initialize(int dev_index, int bus_width)
> ? ? ? ?mmc->f_min = 375000;
> ? ? ? ?mmc->f_max = 48000000;
>
> - ? ? ? mmc_host[dev_index].clock = 0;
> - ? ? ? tegra2_get_setup(&mmc_host[dev_index], dev_index);
> ? ? ? ?mmc_register(mmc);
>
> ? ? ? ?return 0;
> --
> 1.7.0.4
>
>
^ permalink raw reply [flat|nested] 7+ messages in thread