* [U-Boot] [PATCH 1/5] mx53loco: Configure the pins as GPIOs prior to using gpio_get_value
@ 2011-11-15 15:51 Fabio Estevam
2011-11-15 15:51 ` [U-Boot] [PATCH 2/5] mx53ard: " Fabio Estevam
` (5 more replies)
0 siblings, 6 replies; 12+ messages in thread
From: Fabio Estevam @ 2011-11-15 15:51 UTC (permalink / raw)
To: u-boot
Configure the pins as GPIO prior to using gpio_get_value.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
board/freescale/mx53loco/mx53loco.c | 3 +++
1 files changed, 3 insertions(+), 0 deletions(-)
diff --git a/board/freescale/mx53loco/mx53loco.c b/board/freescale/mx53loco/mx53loco.c
index b4c7f33..5e5c38f 100644
--- a/board/freescale/mx53loco/mx53loco.c
+++ b/board/freescale/mx53loco/mx53loco.c
@@ -139,6 +139,9 @@ struct fsl_esdhc_cfg esdhc_cfg[2] = {
int board_mmc_getcd(u8 *cd, struct mmc *mmc)
{
struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+
+ mxc_request_iomux(MX53_PIN_EIM_DA11, IOMUX_CONFIG_ALT1);
+ mxc_request_iomux(MX53_PIN_EIM_DA13, IOMUX_CONFIG_ALT1);
if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
*cd = gpio_get_value(77); /*GPIO3_13*/
--
1.7.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH 2/5] mx53ard: Configure the pins as GPIOs prior to using gpio_get_value
2011-11-15 15:51 [U-Boot] [PATCH 1/5] mx53loco: Configure the pins as GPIOs prior to using gpio_get_value Fabio Estevam
@ 2011-11-15 15:51 ` Fabio Estevam
2011-11-17 6:39 ` Stefano Babic
2011-11-15 15:51 ` [U-Boot] [PATCH 3/5] mx53evk: " Fabio Estevam
` (4 subsequent siblings)
5 siblings, 1 reply; 12+ messages in thread
From: Fabio Estevam @ 2011-11-15 15:51 UTC (permalink / raw)
To: u-boot
Configure the pins as GPIO prior to using gpio_get_value.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
board/freescale/mx53ard/mx53ard.c | 3 +++
1 files changed, 3 insertions(+), 0 deletions(-)
diff --git a/board/freescale/mx53ard/mx53ard.c b/board/freescale/mx53ard/mx53ard.c
index be32aee..e5a1142 100644
--- a/board/freescale/mx53ard/mx53ard.c
+++ b/board/freescale/mx53ard/mx53ard.c
@@ -87,6 +87,9 @@ int board_mmc_getcd(u8 *cd, struct mmc *mmc)
{
struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ mxc_request_iomux(MX53_PIN_GPIO_1, IOMUX_CONFIG_ALT1);
+ mxc_request_iomux(MX53_PIN_GPIO_4, IOMUX_CONFIG_ALT1);
+
if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
*cd = gpio_get_value(1); /*GPIO1_1*/
else
--
1.7.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH 3/5] mx53evk: Configure the pins as GPIOs prior to using gpio_get_value
2011-11-15 15:51 [U-Boot] [PATCH 1/5] mx53loco: Configure the pins as GPIOs prior to using gpio_get_value Fabio Estevam
2011-11-15 15:51 ` [U-Boot] [PATCH 2/5] mx53ard: " Fabio Estevam
@ 2011-11-15 15:51 ` Fabio Estevam
2011-11-16 6:53 ` Jason Liu
2011-11-17 6:39 ` Stefano Babic
2011-11-15 15:51 ` [U-Boot] [PATCH 4/5] mx53smd: " Fabio Estevam
` (3 subsequent siblings)
5 siblings, 2 replies; 12+ messages in thread
From: Fabio Estevam @ 2011-11-15 15:51 UTC (permalink / raw)
To: u-boot
Configure the pins as GPIO prior to using gpio_get_value.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
board/freescale/mx53evk/mx53evk.c | 3 +++
1 files changed, 3 insertions(+), 0 deletions(-)
diff --git a/board/freescale/mx53evk/mx53evk.c b/board/freescale/mx53evk/mx53evk.c
index 335661f..aa4a2c9 100644
--- a/board/freescale/mx53evk/mx53evk.c
+++ b/board/freescale/mx53evk/mx53evk.c
@@ -212,6 +212,9 @@ int board_mmc_getcd(u8 *cd, struct mmc *mmc)
{
struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ mxc_request_iomux(MX53_PIN_EIM_DA11, IOMUX_CONFIG_ALT1);
+ mxc_request_iomux(MX53_PIN_EIM_DA13, IOMUX_CONFIG_ALT1);
+
if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
*cd = gpio_get_value(77); /*GPIO3_13*/
else
--
1.7.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH 4/5] mx53smd: Configure the pins as GPIOs prior to using gpio_get_value
2011-11-15 15:51 [U-Boot] [PATCH 1/5] mx53loco: Configure the pins as GPIOs prior to using gpio_get_value Fabio Estevam
2011-11-15 15:51 ` [U-Boot] [PATCH 2/5] mx53ard: " Fabio Estevam
2011-11-15 15:51 ` [U-Boot] [PATCH 3/5] mx53evk: " Fabio Estevam
@ 2011-11-15 15:51 ` Fabio Estevam
2011-11-17 6:39 ` Stefano Babic
2011-11-15 15:51 ` [U-Boot] [PATCH 5/5] mx51evk: " Fabio Estevam
` (2 subsequent siblings)
5 siblings, 1 reply; 12+ messages in thread
From: Fabio Estevam @ 2011-11-15 15:51 UTC (permalink / raw)
To: u-boot
Configure the pins as GPIO prior to using gpio_get_value.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
board/freescale/mx53smd/mx53smd.c | 1 +
1 files changed, 1 insertions(+), 0 deletions(-)
diff --git a/board/freescale/mx53smd/mx53smd.c b/board/freescale/mx53smd/mx53smd.c
index 87fa7fa..55af4e4 100644
--- a/board/freescale/mx53smd/mx53smd.c
+++ b/board/freescale/mx53smd/mx53smd.c
@@ -134,6 +134,7 @@ struct fsl_esdhc_cfg esdhc_cfg[1] = {
int board_mmc_getcd(u8 *cd, struct mmc *mmc)
{
+ mxc_request_iomux(MX53_PIN_EIM_DA13, IOMUX_CONFIG_ALT1);
*cd = gpio_get_value(77); /*GPIO3_13*/
return 0;
--
1.7.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH 5/5] mx51evk: Configure the pins as GPIOs prior to using gpio_get_value
2011-11-15 15:51 [U-Boot] [PATCH 1/5] mx53loco: Configure the pins as GPIOs prior to using gpio_get_value Fabio Estevam
` (2 preceding siblings ...)
2011-11-15 15:51 ` [U-Boot] [PATCH 4/5] mx53smd: " Fabio Estevam
@ 2011-11-15 15:51 ` Fabio Estevam
2011-11-17 6:40 ` Stefano Babic
2011-11-16 6:53 ` [U-Boot] [PATCH 1/5] mx53loco: " Jason Liu
2011-11-17 6:39 ` Stefano Babic
5 siblings, 1 reply; 12+ messages in thread
From: Fabio Estevam @ 2011-11-15 15:51 UTC (permalink / raw)
To: u-boot
Configure the pins as GPIO prior to using gpio_get_value.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
board/freescale/mx51evk/mx51evk.c | 3 +++
1 files changed, 3 insertions(+), 0 deletions(-)
diff --git a/board/freescale/mx51evk/mx51evk.c b/board/freescale/mx51evk/mx51evk.c
index 37e6e4d..e5b0929 100644
--- a/board/freescale/mx51evk/mx51evk.c
+++ b/board/freescale/mx51evk/mx51evk.c
@@ -265,6 +265,9 @@ int board_mmc_getcd(u8 *cd, struct mmc *mmc)
{
struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ mxc_request_iomux(MX51_PIN_GPIO1_0, IOMUX_CONFIG_ALT1);
+ mxc_request_iomux(MX51_PIN_GPIO1_6, IOMUX_CONFIG_ALT0);
+
if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
*cd = gpio_get_value(0);
else
--
1.7.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH 1/5] mx53loco: Configure the pins as GPIOs prior to using gpio_get_value
2011-11-15 15:51 [U-Boot] [PATCH 1/5] mx53loco: Configure the pins as GPIOs prior to using gpio_get_value Fabio Estevam
` (3 preceding siblings ...)
2011-11-15 15:51 ` [U-Boot] [PATCH 5/5] mx51evk: " Fabio Estevam
@ 2011-11-16 6:53 ` Jason Liu
2011-11-17 6:39 ` Stefano Babic
5 siblings, 0 replies; 12+ messages in thread
From: Jason Liu @ 2011-11-16 6:53 UTC (permalink / raw)
To: u-boot
2011/11/15 Fabio Estevam <festevam@gmail.com>:
> Configure the pins as GPIO prior to using gpio_get_value.
>
> Cc: Jason Liu <r64343@freescale.com>
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <jason.hui@linaro.org>
> ---
> ?board/freescale/mx53loco/mx53loco.c | ? ?3 +++
> ?1 files changed, 3 insertions(+), 0 deletions(-)
>
> diff --git a/board/freescale/mx53loco/mx53loco.c b/board/freescale/mx53loco/mx53loco.c
> index b4c7f33..5e5c38f 100644
> --- a/board/freescale/mx53loco/mx53loco.c
> +++ b/board/freescale/mx53loco/mx53loco.c
> @@ -139,6 +139,9 @@ struct fsl_esdhc_cfg esdhc_cfg[2] = {
> ?int board_mmc_getcd(u8 *cd, struct mmc *mmc)
> ?{
> ? ? ? ?struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
> +
> + ? ? ? mxc_request_iomux(MX53_PIN_EIM_DA11, IOMUX_CONFIG_ALT1);
> + ? ? ? mxc_request_iomux(MX53_PIN_EIM_DA13, IOMUX_CONFIG_ALT1);
>
> ? ? ? ?if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
> ? ? ? ? ? ? ? ?*cd = gpio_get_value(77); /*GPIO3_13*/
> --
> 1.7.1
>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH 3/5] mx53evk: Configure the pins as GPIOs prior to using gpio_get_value
2011-11-15 15:51 ` [U-Boot] [PATCH 3/5] mx53evk: " Fabio Estevam
@ 2011-11-16 6:53 ` Jason Liu
2011-11-17 6:39 ` Stefano Babic
1 sibling, 0 replies; 12+ messages in thread
From: Jason Liu @ 2011-11-16 6:53 UTC (permalink / raw)
To: u-boot
2011/11/15 Fabio Estevam <festevam@gmail.com>:
> Configure the pins as GPIO prior to using gpio_get_value.
>
> Cc: Jason Liu <r64343@freescale.com>
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <jason.hui@linaro.org>
> ---
> ?board/freescale/mx53evk/mx53evk.c | ? ?3 +++
> ?1 files changed, 3 insertions(+), 0 deletions(-)
>
> diff --git a/board/freescale/mx53evk/mx53evk.c b/board/freescale/mx53evk/mx53evk.c
> index 335661f..aa4a2c9 100644
> --- a/board/freescale/mx53evk/mx53evk.c
> +++ b/board/freescale/mx53evk/mx53evk.c
> @@ -212,6 +212,9 @@ int board_mmc_getcd(u8 *cd, struct mmc *mmc)
> ?{
> ? ? ? ?struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
>
> + ? ? ? mxc_request_iomux(MX53_PIN_EIM_DA11, IOMUX_CONFIG_ALT1);
> + ? ? ? mxc_request_iomux(MX53_PIN_EIM_DA13, IOMUX_CONFIG_ALT1);
> +
> ? ? ? ?if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
> ? ? ? ? ? ? ? ?*cd = gpio_get_value(77); /*GPIO3_13*/
> ? ? ? ?else
> --
> 1.7.1
>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH 1/5] mx53loco: Configure the pins as GPIOs prior to using gpio_get_value
2011-11-15 15:51 [U-Boot] [PATCH 1/5] mx53loco: Configure the pins as GPIOs prior to using gpio_get_value Fabio Estevam
` (4 preceding siblings ...)
2011-11-16 6:53 ` [U-Boot] [PATCH 1/5] mx53loco: " Jason Liu
@ 2011-11-17 6:39 ` Stefano Babic
5 siblings, 0 replies; 12+ messages in thread
From: Stefano Babic @ 2011-11-17 6:39 UTC (permalink / raw)
To: u-boot
On 11/15/2011 04:51 PM, Fabio Estevam wrote:
> Configure the pins as GPIO prior to using gpio_get_value.
>
> Cc: Jason Liu<r64343@freescale.com>
> Signed-off-by: Fabio Estevam<fabio.estevam@freescale.com>
> ---
> board/freescale/mx53loco/mx53loco.c | 3 +++
> 1 files changed, 3 insertions(+), 0 deletions(-)
>
Applied to u-boot-imx, thanks
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH 2/5] mx53ard: Configure the pins as GPIOs prior to using gpio_get_value
2011-11-15 15:51 ` [U-Boot] [PATCH 2/5] mx53ard: " Fabio Estevam
@ 2011-11-17 6:39 ` Stefano Babic
0 siblings, 0 replies; 12+ messages in thread
From: Stefano Babic @ 2011-11-17 6:39 UTC (permalink / raw)
To: u-boot
On 11/15/2011 04:51 PM, Fabio Estevam wrote:
> Configure the pins as GPIO prior to using gpio_get_value.
>
> Signed-off-by: Fabio Estevam<fabio.estevam@freescale.com>
> ---
> board/freescale/mx53ard/mx53ard.c | 3 +++
> 1 files changed, 3 insertions(+), 0 deletions(-)
>
> diff --git a/board/freescale/mx53ard/mx53ard.c b/board/freescale/mx53ard/mx53ard.c
> index be32aee..e5a1142 100644
> --- a/board/freescale/mx53ard/mx53ard.c
> +++ b/board/freescale/mx53ard/mx53ard.c
> @@ -87,6 +87,9 @@ int board_mmc_getcd(u8 *cd, struct mmc *mmc)
> {
> struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
>
> + mxc_request_iomux(MX53_PIN_GPIO_1, IOMUX_CONFIG_ALT1);
> + mxc_request_iomux(MX53_PIN_GPIO_4, IOMUX_CONFIG_ALT1);
> +
> if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
> *cd = gpio_get_value(1); /*GPIO1_1*/
> else
Applied to u-boot-imx, thanks
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH 3/5] mx53evk: Configure the pins as GPIOs prior to using gpio_get_value
2011-11-15 15:51 ` [U-Boot] [PATCH 3/5] mx53evk: " Fabio Estevam
2011-11-16 6:53 ` Jason Liu
@ 2011-11-17 6:39 ` Stefano Babic
1 sibling, 0 replies; 12+ messages in thread
From: Stefano Babic @ 2011-11-17 6:39 UTC (permalink / raw)
To: u-boot
On 11/15/2011 04:51 PM, Fabio Estevam wrote:
> Configure the pins as GPIO prior to using gpio_get_value.
>
> Cc: Jason Liu<r64343@freescale.com>
> Signed-off-by: Fabio Estevam<fabio.estevam@freescale.com>
> ---
> board/freescale/mx53evk/mx53evk.c | 3 +++
> 1 files changed, 3 insertions(+), 0 deletions(-)
>
> diff --git a/board/freescale/mx53evk/mx53evk.c b/board/freescale/mx53evk/mx53evk.c
> index 335661f..aa4a2c9 100644
> --- a/board/freescale/mx53evk/mx53evk.c
> +++ b/board/freescale/mx53evk/mx53evk.c
> @@ -212,6 +212,9 @@ int board_mmc_getcd(u8 *cd, struct mmc *mmc)
> {
> struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
>
> + mxc_request_iomux(MX53_PIN_EIM_DA11, IOMUX_CONFIG_ALT1);
> + mxc_request_iomux(MX53_PIN_EIM_DA13, IOMUX_CONFIG_ALT1);
> +
> if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
> *cd = gpio_get_value(77); /*GPIO3_13*/
> else
Applied to u-boot-imx, thanks
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH 4/5] mx53smd: Configure the pins as GPIOs prior to using gpio_get_value
2011-11-15 15:51 ` [U-Boot] [PATCH 4/5] mx53smd: " Fabio Estevam
@ 2011-11-17 6:39 ` Stefano Babic
0 siblings, 0 replies; 12+ messages in thread
From: Stefano Babic @ 2011-11-17 6:39 UTC (permalink / raw)
To: u-boot
On 11/15/2011 04:51 PM, Fabio Estevam wrote:
> Configure the pins as GPIO prior to using gpio_get_value.
>
> Signed-off-by: Fabio Estevam<fabio.estevam@freescale.com>
> ---
> board/freescale/mx53smd/mx53smd.c | 1 +
> 1 files changed, 1 insertions(+), 0 deletions(-)
>
> diff --git a/board/freescale/mx53smd/mx53smd.c b/board/freescale/mx53smd/mx53smd.c
> index 87fa7fa..55af4e4 100644
> --- a/board/freescale/mx53smd/mx53smd.c
> +++ b/board/freescale/mx53smd/mx53smd.c
> @@ -134,6 +134,7 @@ struct fsl_esdhc_cfg esdhc_cfg[1] = {
>
> int board_mmc_getcd(u8 *cd, struct mmc *mmc)
> {
> + mxc_request_iomux(MX53_PIN_EIM_DA13, IOMUX_CONFIG_ALT1);
> *cd = gpio_get_value(77); /*GPIO3_13*/
>
> return 0;
Applied to u-boot-imx, thanks
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 12+ messages in thread
* [U-Boot] [PATCH 5/5] mx51evk: Configure the pins as GPIOs prior to using gpio_get_value
2011-11-15 15:51 ` [U-Boot] [PATCH 5/5] mx51evk: " Fabio Estevam
@ 2011-11-17 6:40 ` Stefano Babic
0 siblings, 0 replies; 12+ messages in thread
From: Stefano Babic @ 2011-11-17 6:40 UTC (permalink / raw)
To: u-boot
On 11/15/2011 04:51 PM, Fabio Estevam wrote:
> Configure the pins as GPIO prior to using gpio_get_value.
>
> Signed-off-by: Fabio Estevam<fabio.estevam@freescale.com>
> ---
> board/freescale/mx51evk/mx51evk.c | 3 +++
> 1 files changed, 3 insertions(+), 0 deletions(-)
>
> diff --git a/board/freescale/mx51evk/mx51evk.c b/board/freescale/mx51evk/mx51evk.c
> index 37e6e4d..e5b0929 100644
> --- a/board/freescale/mx51evk/mx51evk.c
> +++ b/board/freescale/mx51evk/mx51evk.c
> @@ -265,6 +265,9 @@ int board_mmc_getcd(u8 *cd, struct mmc *mmc)
> {
> struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
>
> + mxc_request_iomux(MX51_PIN_GPIO1_0, IOMUX_CONFIG_ALT1);
> + mxc_request_iomux(MX51_PIN_GPIO1_6, IOMUX_CONFIG_ALT0);
> +
> if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
> *cd = gpio_get_value(0);
> else
Applied to u-boot-imx, thanks
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2011-11-17 6:40 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-11-15 15:51 [U-Boot] [PATCH 1/5] mx53loco: Configure the pins as GPIOs prior to using gpio_get_value Fabio Estevam
2011-11-15 15:51 ` [U-Boot] [PATCH 2/5] mx53ard: " Fabio Estevam
2011-11-17 6:39 ` Stefano Babic
2011-11-15 15:51 ` [U-Boot] [PATCH 3/5] mx53evk: " Fabio Estevam
2011-11-16 6:53 ` Jason Liu
2011-11-17 6:39 ` Stefano Babic
2011-11-15 15:51 ` [U-Boot] [PATCH 4/5] mx53smd: " Fabio Estevam
2011-11-17 6:39 ` Stefano Babic
2011-11-15 15:51 ` [U-Boot] [PATCH 5/5] mx51evk: " Fabio Estevam
2011-11-17 6:40 ` Stefano Babic
2011-11-16 6:53 ` [U-Boot] [PATCH 1/5] mx53loco: " Jason Liu
2011-11-17 6:39 ` Stefano Babic
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox