[U-Boot] [PATCH v7 1/4] net: imx: Add multi-FEC support for imx_get_mac_from_fuse

[U-Boot] [PATCH v7 1/4] net: imx: Add multi-FEC support for imx_get_mac_from_fuse

[Fabio Estevam]

Add multi-FEC support for imx_get_mac_from_fuse by passing dev_id as a parameter.

This feature is important on mx28 SoC for example that has two FEC ports.

Cc: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
Change since v6:
- No changes. Introduced on this series

 arch/arm/cpu/arm1136/mx35/generic.c      |    2 +-
 arch/arm/cpu/arm926ejs/mx25/generic.c    |    2 +-
 arch/arm/cpu/arm926ejs/mx27/generic.c    |    2 +-
 arch/arm/cpu/armv7/mx6/soc.c             |    2 +-
 arch/arm/include/asm/arch-mx6/imx-regs.h |    2 +-
 board/denx/m28evk/m28evk.c               |    4 ++--
 drivers/net/fec_mxc.c                    |    9 +++++----
 drivers/net/fec_mxc.h                    |    2 +-
 8 files changed, 13 insertions(+), 12 deletions(-)

diff --git a/arch/arm/cpu/arm1136/mx35/generic.c b/arch/arm/cpu/arm1136/mx35/generic.c
index ac4838f..d41613e 100644
--- a/arch/arm/cpu/arm1136/mx35/generic.c
+++ b/arch/arm/cpu/arm1136/mx35/generic.c
@@ -393,7 +393,7 @@ unsigned int mxc_get_clock(enum mxc_clock clk)
 /*
  * The MX35 has no fuse for MAC, return a NULL MAC
  */
-void imx_get_mac_from_fuse(unsigned char *mac)
+void imx_get_mac_from_fuse(int dev_id, unsigned char *mac)
 {
 	memset(mac, 0, 6);
 }
diff --git a/arch/arm/cpu/arm926ejs/mx25/generic.c b/arch/arm/cpu/arm926ejs/mx25/generic.c
index c045a0b..9cadb7c 100644
--- a/arch/arm/cpu/arm926ejs/mx25/generic.c
+++ b/arch/arm/cpu/arm926ejs/mx25/generic.c
@@ -312,7 +312,7 @@ void mx25_fec_init_pins(void)
 
 }
 
-void imx_get_mac_from_fuse(unsigned char *mac)
+void imx_get_mac_from_fuse(int dev_id, unsigned char *mac)
 {
 	int i;
 	struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE;
diff --git a/arch/arm/cpu/arm926ejs/mx27/generic.c b/arch/arm/cpu/arm926ejs/mx27/generic.c
index 222a8e9..34c20e1 100644
--- a/arch/arm/cpu/arm926ejs/mx27/generic.c
+++ b/arch/arm/cpu/arm926ejs/mx27/generic.c
@@ -314,7 +314,7 @@ void mx27_fec_init_pins(void)
 		imx_gpio_mode(mode[i]);
 }
 
-void imx_get_mac_from_fuse(unsigned char *mac)
+void imx_get_mac_from_fuse(int dev_id, unsigned char *mac)
 {
 	int i;
 	struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE;
diff --git a/arch/arm/cpu/armv7/mx6/soc.c b/arch/arm/cpu/armv7/mx6/soc.c
index dff5e4e..5a6f9e2 100644
--- a/arch/arm/cpu/armv7/mx6/soc.c
+++ b/arch/arm/cpu/armv7/mx6/soc.c
@@ -63,7 +63,7 @@ int arch_cpu_init(void)
 #endif
 
 #if defined(CONFIG_FEC_MXC)
-void imx_get_mac_from_fuse(unsigned char *mac)
+void imx_get_mac_from_fuse(int dev_id, unsigned char *mac)
 {
 	struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE;
 	struct fuse_bank *bank = &iim->bank[4];
diff --git a/arch/arm/include/asm/arch-mx6/imx-regs.h b/arch/arm/include/asm/arch-mx6/imx-regs.h
index 85d55b7..dfec6b0 100644
--- a/arch/arm/include/asm/arch-mx6/imx-regs.h
+++ b/arch/arm/include/asm/arch-mx6/imx-regs.h
@@ -167,7 +167,7 @@
 #if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__))
 #include <asm/types.h>
 
-extern void imx_get_mac_from_fuse(unsigned char *mac);
+extern void imx_get_mac_from_fuse(int dev_id, unsigned char *mac);
 
 /* System Reset Controller (SRC) */
 struct src {
diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
index fcee046..a0fabc0 100644
--- a/board/denx/m28evk/m28evk.c
+++ b/board/denx/m28evk/m28evk.c
@@ -181,7 +181,7 @@ int board_eth_init(bd_t *bis)
 #ifdef	CONFIG_M28_FEC_MAC_IN_OCOTP
 
 #define	MXS_OCOTP_MAX_TIMEOUT	1000000
-void imx_get_mac_from_fuse(char *mac)
+void imx_get_mac_from_fuse(int dev_id, char *mac)
 {
 	struct mx28_ocotp_regs *ocotp_regs =
 		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
@@ -207,7 +207,7 @@ void imx_get_mac_from_fuse(char *mac)
 	mac[5] = data & 0xff;
 }
 #else
-void imx_get_mac_from_fuse(char *mac)
+void imx_get_mac_from_fuse(int dev_id, char *mac)
 {
 	memset(mac, 0, 6);
 }
diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c
index b05a4c0..1529a27 100644
--- a/drivers/net/fec_mxc.c
+++ b/drivers/net/fec_mxc.c
@@ -345,9 +345,10 @@ static void fec_rbd_clean(int last, struct fec_bd *pRbd)
 	writew(0, &pRbd->data_length);
 }
 
-static int fec_get_hwaddr(struct eth_device *dev, unsigned char *mac)
+static int fec_get_hwaddr(struct eth_device *dev, int dev_id,
+						unsigned char *mac)
 {
-	imx_get_mac_from_fuse(mac);
+	imx_get_mac_from_fuse(dev_id, mac);
 	return !is_valid_ether_addr(mac);
 }
 
@@ -812,8 +813,8 @@ static int fec_probe(bd_t *bd, int dev_id, int phy_id, uint32_t base_addr)
 
 	eth_register(edev);
 
-	if (fec_get_hwaddr(edev, ethaddr) == 0) {
-		debug("got MAC address from fuse: %pM\n", ethaddr);
+	if (fec_get_hwaddr(edev, dev_id, ethaddr) == 0) {
+		debug("got MAC%d address from fuse: %pM\n", dev_id, ethaddr);
 		memcpy(edev->enetaddr, ethaddr, 6);
 	}
 
diff --git a/drivers/net/fec_mxc.h b/drivers/net/fec_mxc.h
index 8b26645..6c4aa4b 100644
--- a/drivers/net/fec_mxc.h
+++ b/drivers/net/fec_mxc.h
@@ -32,7 +32,7 @@
 #ifndef __FEC_MXC_H
 #define __FEC_MXC_H
 
-void imx_get_mac_from_fuse(unsigned char *mac);
+void imx_get_mac_from_fuse(int dev_id, unsigned char *mac);
 
 /**
  * Layout description of the FEC
-- 
1.7.1

[U-Boot] [PATCH v7 2/4] mx28: Let imx_get_mac_from_fuse be common for mx28

[Fabio Estevam]

Let imx_get_mac_from_fuse function be a common function, so that other
mx28 boards can reuse it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
Changes since v6:
- Let mac[5] be set inside mx28_adjust_mac
Changes since v5:
- Allow the MAC vendor to be overriden
Changes since v4:
- No changes
Change since v3:
- Add a note about the first two MAC addresses being from Freescale vendor.
 arch/arm/cpu/arm926ejs/mx28/mx28.c |   46 ++++++++++++++++++++++++++++++++++++
 board/denx/m28evk/m28evk.c         |   35 ---------------------------
 2 files changed, 46 insertions(+), 35 deletions(-)

diff --git a/arch/arm/cpu/arm926ejs/mx28/mx28.c b/arch/arm/cpu/arm926ejs/mx28/mx28.c
index 088c019..ee4e337 100644
--- a/arch/arm/cpu/arm926ejs/mx28/mx28.c
+++ b/arch/arm/cpu/arm926ejs/mx28/mx28.c
@@ -214,6 +214,52 @@ int cpu_eth_init(bd_t *bis)
 }
 #endif
 
+static void __mx28_adjust_mac(int dev_id, char *mac)
+{
+	mac[0] = 0x00;
+	mac[1] = 0x04; /* Use FSL vendor MAC address by default */
+
+	if (dev_id == 1) /* Let MAC1 be MAC0 + 1 by default */
+		mac[5] += 1;
+}
+
+void mx28_adjust_mac(int dev_id, char *mac)
+	__attribute__((weak, alias("__mx28_adjust_mac")));
+
+#ifdef	CONFIG_MX28_FEC_MAC_IN_OCOTP
+
+#define	MXS_OCOTP_MAX_TIMEOUT	1000000
+void imx_get_mac_from_fuse(int dev_id, char *mac)
+{
+	struct mx28_ocotp_regs *ocotp_regs =
+		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
+	uint32_t data;
+
+	memset(mac, 0, 6);
+
+	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
+
+	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
+				MXS_OCOTP_MAX_TIMEOUT)) {
+		printf("MXS FEC: Can't get MAC from OCOTP\n");
+		return;
+	}
+
+	data = readl(&ocotp_regs->hw_ocotp_cust0);
+
+	mac[2] = (data >> 24) & 0xff;
+	mac[3] = (data >> 16) & 0xff;
+	mac[4] = (data >> 8) & 0xff;
+	mac[5] = data & 0xff;
+	mx28_adjust_mac(dev_id, mac);
+}
+#else
+void imx_get_mac_from_fuse(int dev_id, char *mac)
+{
+	memset(mac, 0, 6);
+}
+#endif
+
 U_BOOT_CMD(
 	clocks,	CONFIG_SYS_MAXARGS, 1, do_mx28_showclocks,
 	"display clocks",
diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
index a0fabc0..005446a 100644
--- a/board/denx/m28evk/m28evk.c
+++ b/board/denx/m28evk/m28evk.c
@@ -178,39 +178,4 @@ int board_eth_init(bd_t *bis)
 	return ret;
 }
 
-#ifdef	CONFIG_M28_FEC_MAC_IN_OCOTP
-
-#define	MXS_OCOTP_MAX_TIMEOUT	1000000
-void imx_get_mac_from_fuse(int dev_id, char *mac)
-{
-	struct mx28_ocotp_regs *ocotp_regs =
-		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
-	uint32_t data;
-
-	memset(mac, 0, 6);
-
-	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
-
-	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
-				MXS_OCOTP_MAX_TIMEOUT)) {
-		printf("MXS FEC: Can't get MAC from OCOTP\n");
-		return;
-	}
-
-	data = readl(&ocotp_regs->hw_ocotp_cust0);
-
-	mac[0] = 0x00;
-	mac[1] = 0x04;
-	mac[2] = (data >> 24) & 0xff;
-	mac[3] = (data >> 16) & 0xff;
-	mac[4] = (data >> 8) & 0xff;
-	mac[5] = data & 0xff;
-}
-#else
-void imx_get_mac_from_fuse(int dev_id, char *mac)
-{
-	memset(mac, 0, 6);
-}
-#endif
-
 #endif
-- 
1.7.1

[U-Boot] [PATCH v7 3/4] mx28: Let dram_init be common for mx28

[Fabio Estevam]

Let dram_init function be a common function, so that other mx28 boards
can reuse it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
---
Changes since v6:
- Added Acked-by line
Changes since v5:
- Change return value on dram_init() 
Changes since v4:
- Call mx28_dram_init from m28evk.c
Changes since v3:
- Rename dram_init to mx28_dram_init
 arch/arm/cpu/arm926ejs/mx28/mx28.c         |   21 +++++++++++++++++++++
 arch/arm/include/asm/arch-mx28/sys_proto.h |    2 ++
 board/denx/m28evk/m28evk.c                 |   18 +-----------------
 3 files changed, 24 insertions(+), 17 deletions(-)

diff --git a/arch/arm/cpu/arm926ejs/mx28/mx28.c b/arch/arm/cpu/arm926ejs/mx28/mx28.c
index ee4e337..c95e900 100644
--- a/arch/arm/cpu/arm926ejs/mx28/mx28.c
+++ b/arch/arm/cpu/arm926ejs/mx28/mx28.c
@@ -260,6 +260,27 @@ void imx_get_mac_from_fuse(int dev_id, char *mac)
 }
 #endif
 
+#define	HW_DIGCTRL_SCRATCH0	0x8001c280
+#define	HW_DIGCTRL_SCRATCH1	0x8001c290
+int mx28_dram_init(void)
+{
+	uint32_t sz[2];
+
+	sz[0] = readl(HW_DIGCTRL_SCRATCH0);
+	sz[1] = readl(HW_DIGCTRL_SCRATCH1);
+
+	if (sz[0] != sz[1]) {
+		printf("MX28:\n"
+			"Error, the RAM size in HW_DIGCTRL_SCRATCH0 and\n"
+			"HW_DIGCTRL_SCRATCH1 is not the same. Please\n"
+			"verify these two registers contain valid RAM size!\n");
+		hang();
+	}
+
+	gd->ram_size = sz[0];
+	return 0;
+}
+
 U_BOOT_CMD(
 	clocks,	CONFIG_SYS_MAXARGS, 1, do_mx28_showclocks,
 	"display clocks",
diff --git a/arch/arm/include/asm/arch-mx28/sys_proto.h b/arch/arm/include/asm/arch-mx28/sys_proto.h
index be1f7db..f101494 100644
--- a/arch/arm/include/asm/arch-mx28/sys_proto.h
+++ b/arch/arm/include/asm/arch-mx28/sys_proto.h
@@ -35,4 +35,6 @@ void mx28_common_spl_init(const iomux_cfg_t *iomux_setup,
 			const unsigned int iomux_size);
 #endif
 
+int mx28_dram_init(void);
+
 #endif	/* __MX28_H__ */
diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
index 005446a..53df476 100644
--- a/board/denx/m28evk/m28evk.c
+++ b/board/denx/m28evk/m28evk.c
@@ -70,25 +70,9 @@ int board_init(void)
 	return 0;
 }
 
-#define	HW_DIGCTRL_SCRATCH0	0x8001c280
-#define	HW_DIGCTRL_SCRATCH1	0x8001c290
 int dram_init(void)
 {
-	uint32_t sz[2];
-
-	sz[0] = readl(HW_DIGCTRL_SCRATCH0);
-	sz[1] = readl(HW_DIGCTRL_SCRATCH1);
-
-	if (sz[0] != sz[1]) {
-		printf("MX28:\n"
-			"Error, the RAM size in HW_DIGCTRL_SCRATCH0 and\n"
-			"HW_DIGCTRL_SCRATCH1 is not the same. Please\n"
-			"verify these two registers contain valid RAM size!\n");
-		hang();
-	}
-
-	gd->ram_size = sz[0];
-	return 0;
+	return mx28_dram_init();
 }
 
 #ifdef	CONFIG_CMD_MMC
-- 
1.7.1

[U-Boot] [PATCH v7 4/4] mx28evk: Add initial support for MX28EVK board

[Fabio Estevam]

Add initial support for Freescale MX28EVK board.

Tested boot via SD card and by loading a kernel via TFTP through
the FEC interface.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
---
- For correct operation of saving environment variables into the SD card,
the following patch is needed:
http://lists.denx.de/pipermail/u-boot/2011-November/111448.html
Changes since v6:
- Added Acked-by line
Changes since v5:
- Fix tab vs spaces on mx28evk.h
- Change return value on dram_init() 
Changes since v4:
- No changes
Changes since v3:
- Fix Copyright in mx28evk.h
- Call mx28_dram_init from dram_init
Changes since v2:
- Generate the patch again due to error in applying unrelated changes
Changes since v1:
- Read the MAC from fuses
- Use tabs instead of space in u-boot.bd
- Use puts instead of print
- Factor out mac reading function
- Factor out ddr size calculation function
- Use GENERATED_GBL_DATA_SIZE
- Protect CONFIG_ENV_IS_IN_MMC
 MAINTAINERS                       |    1 +
 board/freescale/mx28evk/Makefile  |   49 ++++++++++
 board/freescale/mx28evk/iomux.c   |  138 +++++++++++++++++++++++++++++
 board/freescale/mx28evk/mx28evk.c |  169 +++++++++++++++++++++++++++++++++++
 board/freescale/mx28evk/u-boot.bd |   14 +++
 boards.cfg                        |    1 +
 include/configs/mx28evk.h         |  176 +++++++++++++++++++++++++++++++++++++
 7 files changed, 548 insertions(+), 0 deletions(-)
 create mode 100644 board/freescale/mx28evk/Makefile
 create mode 100644 board/freescale/mx28evk/iomux.c
 create mode 100644 board/freescale/mx28evk/mx28evk.c
 create mode 100644 board/freescale/mx28evk/u-boot.bd
 create mode 100644 include/configs/mx28evk.h

diff --git a/MAINTAINERS b/MAINTAINERS
index a56ca10..72e1089 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -639,6 +639,7 @@ Kristoffer Ericson <kristoffer.ericson@gmail.com>
 Fabio Estevam <fabio.estevam@freescale.com>
 
 	mx25pdk		i.MX25
+	mx28evk		i.MX28
 	mx31pdk		i.MX31
 	mx53ard		i.MX53
 	mx53smd		i.MX53
diff --git a/board/freescale/mx28evk/Makefile b/board/freescale/mx28evk/Makefile
new file mode 100644
index 0000000..7459107
--- /dev/null
+++ b/board/freescale/mx28evk/Makefile
@@ -0,0 +1,49 @@
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+ifndef	CONFIG_SPL_BUILD
+COBJS	:= mx28evk.o
+else
+COBJS	:= iomux.o
+endif
+
+SRCS	:= $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+
+$(LIB):	$(obj).depend $(OBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+all:	$(ALL)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/mx28evk/iomux.c b/board/freescale/mx28evk/iomux.c
new file mode 100644
index 0000000..904e3f3
--- /dev/null
+++ b/board/freescale/mx28evk/iomux.c
@@ -0,0 +1,138 @@
+/*
+ * Freescale MX28EVK IOMUX setup
+ *
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <config.h>
+#include <asm/io.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
+
+#define	MUX_CONFIG_SSP0	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
+#define	MUX_CONFIG_ENET	(MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
+#define	MUX_CONFIG_EMI	(MXS_PAD_3V3 | MXS_PAD_12MA | MXS_PAD_NOPULL)
+
+const iomux_cfg_t iomux_setup[] = {
+	/* DUART */
+	MX28_PAD_PWM0__DUART_RX,
+	MX28_PAD_PWM1__DUART_TX,
+
+	/* MMC0 */
+	MX28_PAD_SSP0_DATA0__SSP0_D0 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA1__SSP0_D1 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA2__SSP0_D2 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA3__SSP0_D3 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA4__SSP0_D4 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA5__SSP0_D5 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA6__SSP0_D6 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DATA7__SSP0_D7 | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_CMD__SSP0_CMD | MUX_CONFIG_SSP0,
+	MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT |
+		(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+	MX28_PAD_SSP0_SCK__SSP0_SCK |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+	/* write protect */
+	MX28_PAD_SSP1_SCK__GPIO_2_12,
+	/* MMC0 slot power enable */
+	MX28_PAD_PWM3__GPIO_3_28 |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+
+	/* FEC0 */
+	MX28_PAD_ENET0_MDC__ENET0_MDC | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_MDIO__ENET0_MDIO | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RX_EN__ENET0_RX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TX_EN__ENET0_TX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD0__ENET0_RXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD1__ENET0_RXD1 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD0__ENET0_TXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD1__ENET0_TXD1 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET_CLK__CLKCTRL_ENET | MUX_CONFIG_ENET,
+	/* FEC0 Enable */
+	MX28_PAD_SSP1_DATA3__GPIO_2_15 |
+		(MXS_PAD_12MA | MXS_PAD_3V3),
+	/* FEC0 Reset */
+	MX28_PAD_ENET0_RX_CLK__GPIO_4_13 |
+		(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+
+	/* FEC1 */
+	MX28_PAD_ENET0_COL__ENET1_TX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_CRS__ENET1_RX_EN | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD2__ENET1_RXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_RXD3__ENET1_RXD1 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD2__ENET1_TXD0 | MUX_CONFIG_ENET,
+	MX28_PAD_ENET0_TXD3__ENET1_TXD1 | MUX_CONFIG_ENET,
+
+	/* EMI */
+	MX28_PAD_EMI_D00__EMI_DATA0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D01__EMI_DATA1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D02__EMI_DATA2 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D03__EMI_DATA3 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D04__EMI_DATA4 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D05__EMI_DATA5 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D06__EMI_DATA6 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D07__EMI_DATA7 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D08__EMI_DATA8 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D09__EMI_DATA9 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D10__EMI_DATA10 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D11__EMI_DATA11 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D12__EMI_DATA12 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D13__EMI_DATA13 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D14__EMI_DATA14 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_D15__EMI_DATA15 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_ODT0__EMI_ODT0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQM0__EMI_DQM0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_ODT1__EMI_ODT1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQM1__EMI_DQM1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DDR_OPEN_FB__EMI_DDR_OPEN_FEEDBACK | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CLK__EMI_CLK | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQS0__EMI_DQS0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DQS1__EMI_DQS1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_DDR_OPEN__EMI_DDR_OPEN | MUX_CONFIG_EMI,
+
+	MX28_PAD_EMI_A00__EMI_ADDR0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A01__EMI_ADDR1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A02__EMI_ADDR2 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A03__EMI_ADDR3 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A04__EMI_ADDR4 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A05__EMI_ADDR5 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A06__EMI_ADDR6 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A07__EMI_ADDR7 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A08__EMI_ADDR8 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A09__EMI_ADDR9 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A10__EMI_ADDR10 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A11__EMI_ADDR11 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A12__EMI_ADDR12 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A13__EMI_ADDR13 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_A14__EMI_ADDR14 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_BA0__EMI_BA0 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_BA1__EMI_BA1 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_BA2__EMI_BA2 | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CASN__EMI_CASN | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_RASN__EMI_RASN | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_WEN__EMI_WEN | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CE0N__EMI_CE0N | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CE1N__EMI_CE1N | MUX_CONFIG_EMI,
+	MX28_PAD_EMI_CKE__EMI_CKE | MUX_CONFIG_EMI,
+};
+
+void board_init_ll(void)
+{
+	mx28_common_spl_init(iomux_setup, ARRAY_SIZE(iomux_setup));
+}
diff --git a/board/freescale/mx28evk/mx28evk.c b/board/freescale/mx28evk/mx28evk.c
new file mode 100644
index 0000000..0d04d44
--- /dev/null
+++ b/board/freescale/mx28evk/mx28evk.c
@@ -0,0 +1,169 @@
+/*
+ * Freescale MX28EVK board
+ *
+ * (C) Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * Based on m28evk.c:
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <linux/mii.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <errno.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Functions
+ */
+int board_early_init_f(void)
+{
+	/* IO0 clock at 480MHz */
+	mx28_set_ioclk(MXC_IOCLK0, 480000);
+	/* IO1 clock at 480MHz */
+	mx28_set_ioclk(MXC_IOCLK1, 480000);
+
+	/* SSP0 clock at 96MHz */
+	mx28_set_sspclk(MXC_SSPCLK0, 96000, 0);
+	/* SSP2 clock at 96MHz */
+	mx28_set_sspclk(MXC_SSPCLK2, 96000, 0);
+
+	return 0;
+}
+
+int dram_init(void)
+{
+	return mx28_dram_init();
+}
+
+int board_init(void)
+{
+	/* Adress of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+	return 0;
+}
+
+#ifdef	CONFIG_CMD_MMC
+static int mx28evk_mmc_wp(int id)
+{
+	if (id != 0) {
+		printf("MXS MMC: Invalid card selected (card id = %d)\n", id);
+		return 1;
+	}
+
+	return gpio_get_value(MX28_PAD_SSP1_SCK__GPIO_2_12);
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	/* Configure WP as input */
+	gpio_direction_input(MX28_PAD_SSP1_SCK__GPIO_2_12);
+
+	/* Configure MMC0 Power Enable */
+	gpio_direction_output(MX28_PAD_PWM3__GPIO_3_28, 0);
+
+	return mxsmmc_initialize(bis, 0, mx28evk_mmc_wp);
+}
+#endif
+
+#ifdef	CONFIG_CMD_NET
+
+#define	MII_OPMODE_STRAP_OVERRIDE	0x16
+#define	MII_PHY_CTRL1			0x1e
+#define	MII_PHY_CTRL2			0x1f
+
+int fecmxc_mii_postcall(int phy)
+{
+	miiphy_write("FEC1", phy, MII_BMCR, 0x9000);
+	miiphy_write("FEC1", phy, MII_OPMODE_STRAP_OVERRIDE, 0x0202);
+	if (phy == 3)
+		miiphy_write("FEC1", 3, MII_PHY_CTRL2, 0x8180);
+	return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	struct mx28_clkctrl_regs *clkctrl_regs =
+		(struct mx28_clkctrl_regs *)MXS_CLKCTRL_BASE;
+	struct eth_device *dev;
+	int ret;
+
+	ret = cpu_eth_init(bis);
+
+	/* MX28EVK uses ENET_CLK PAD to drive FEC clock */
+	writel(CLKCTRL_ENET_TIME_SEL_RMII_CLK | CLKCTRL_ENET_CLK_OUT_EN,
+					&clkctrl_regs->hw_clkctrl_enet);
+
+	/* Power-on FECs */
+	gpio_direction_output(MX28_PAD_SSP1_DATA3__GPIO_2_15, 0);
+
+	/* Reset FEC PHYs */
+	gpio_direction_output(MX28_PAD_ENET0_RX_CLK__GPIO_4_13, 0);
+	udelay(200);
+	gpio_set_value(MX28_PAD_ENET0_RX_CLK__GPIO_4_13, 1);
+
+	ret = fecmxc_initialize_multi(bis, 0, 0, MXS_ENET0_BASE);
+	if (ret) {
+		puts("FEC MXS: Unable to init FEC0\n");
+		return ret;
+	}
+
+	ret = fecmxc_initialize_multi(bis, 1, 3, MXS_ENET1_BASE);
+	if (ret) {
+		puts("FEC MXS: Unable to init FEC1\n");
+		return ret;
+	}
+
+	dev = eth_get_dev_by_name("FEC0");
+	if (!dev) {
+		puts("FEC MXS: Unable to get FEC0 device entry\n");
+		return -EINVAL;
+	}
+
+	ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
+	if (ret) {
+		puts("FEC MXS: Unable to register FEC0 mii postcall\n");
+		return ret;
+	}
+
+	dev = eth_get_dev_by_name("FEC1");
+	if (!dev) {
+		puts("FEC MXS: Unable to get FEC1 device entry\n");
+		return -EINVAL;
+	}
+
+	ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
+	if (ret) {
+		puts("FEC MXS: Unable to register FEC1 mii postcall\n");
+		return ret;
+	}
+
+	return ret;
+}
+
+#endif
diff --git a/board/freescale/mx28evk/u-boot.bd b/board/freescale/mx28evk/u-boot.bd
new file mode 100644
index 0000000..c60615a
--- /dev/null
+++ b/board/freescale/mx28evk/u-boot.bd
@@ -0,0 +1,14 @@
+sources {
+	u_boot_spl="spl/u-boot-spl.bin";
+	u_boot="u-boot.bin";
+}
+
+section (0) {
+	load u_boot_spl > 0x0000;
+	load ivt (entry = 0x0014) > 0x8000;
+	hab call 0x8000;
+
+	load u_boot > 0x40000100;
+	load ivt (entry = 0x40000100) > 0x8000;
+	hab call 0x8000;
+}
diff --git a/boards.cfg b/boards.cfg
index 1e5b3e0..e859024 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -160,6 +160,7 @@ zmx25                        arm         arm926ejs   zmx25               syteco
 imx27lite                    arm         arm926ejs   imx27lite           logicpd        mx27
 magnesium                    arm         arm926ejs   imx27lite           logicpd        mx27
 m28evk                       arm         arm926ejs   -                   denx           mx28
+mx28evk                      arm         arm926ejs   -                   freescale      mx28
 nhk8815                      arm         arm926ejs   nhk8815             st             nomadik
 nhk8815_onenand              arm         arm926ejs   nhk8815             st             nomadik       nhk8815:BOOT_ONENAND
 omap1610h2		     arm	 arm926ejs   omap1610inn	 ti		omap	    omap1610inn:CS3_BOOT
diff --git a/include/configs/mx28evk.h b/include/configs/mx28evk.h
new file mode 100644
index 0000000..5b8a1bf
--- /dev/null
+++ b/include/configs/mx28evk.h
@@ -0,0 +1,176 @@
+/*
+ * (C) Copyright 2011 Freescale Semiconductor, Inc.
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * Based on m28evk.h:
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/arch/regs-base.h>
+
+/*
+ * SoC configurations
+ */
+#define CONFIG_MX28				/* i.MX28 SoC */
+#define CONFIG_MXS_GPIO			/* GPIO control */
+#define CONFIG_SYS_HZ		1000		/* Ticks per second */
+
+#define CONFIG_MACH_TYPE	MACH_TYPE_MX28EVK
+
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_ICACHE_OFF
+#define CONFIG_SYS_DCACHE_OFF
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_ARCH_MISC_INIT
+
+/*
+ * SPL
+ */
+#define CONFIG_SPL
+#define CONFIG_SPL_NO_CPU_SUPPORT_CODE
+#define CONFIG_SPL_START_S_PATH	"arch/arm/cpu/arm926ejs/mx28"
+#define CONFIG_SPL_LDSCRIPT	"arch/arm/cpu/arm926ejs/mx28/u-boot-spl.lds"
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+
+/*
+ * U-Boot Commands
+ */
+#include <config_cmd_default.h>
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_FAT
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_GPIO
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+
+/*
+ * Memory configurations
+ */
+#define CONFIG_NR_DRAM_BANKS		1		/* 1 bank of DRAM */
+#define PHYS_SDRAM_1			0x40000000	/* Base address */
+#define PHYS_SDRAM_1_SIZE		0x40000000	/* Max 1 GB RAM */
+#define CONFIG_STACKSIZE		(128 * 1024)	/* 128 KB stack */
+#define CONFIG_SYS_MALLOC_LEN		0x00400000	/* 4 MB for malloc */
+#define CONFIG_SYS_MEMTEST_START	0x40000000	/* Memtest start adr */
+#define CONFIG_SYS_MEMTEST_END		0x40400000	/* 4 MB RAM test */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+/* Point initial SP in SRAM so SPL can use it too. */
+
+#define CONFIG_SYS_INIT_RAM_ADDR	0x00002000
+#define CONFIG_SYS_INIT_RAM_SIZE	(128 * 1024)
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/*
+ * We need to sacrifice first 4 bytes of RAM here to avoid triggering some
+ * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot
+ * binary. In case there was more of this mess, 0x100 bytes are skipped.
+ */
+#define CONFIG_SYS_TEXT_BASE	0x40000100
+
+#define CONFIG_ENV_OVERWRITE
+/*
+ * U-Boot general configurations
+ */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_PROMPT	"MX28EVK U-Boot > "
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O buffer size */
+#define CONFIG_SYS_PBSIZE	\
+	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+						/* Print buffer size */
+#define CONFIG_SYS_MAXARGS	32		/* Max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
+						/* Boot argument buffer size */
+#define CONFIG_VERSION_VARIABLE	/* U-BOOT version */
+#define CONFIG_AUTO_COMPLETE		/* Command auto complete */
+#define CONFIG_CMDLINE_EDITING		/* Command history etc */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+
+/*
+ * Serial Driver
+ */
+#define CONFIG_PL011_SERIAL
+#define CONFIG_PL011_CLOCK		24000000
+#define CONFIG_PL01x_PORTS		{ (void *)MXS_UARTDBG_BASE }
+#define CONFIG_CONS_INDEX		0
+#define CONFIG_BAUDRATE			115200	/* Default baud rate */
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * MMC Driver
+ */
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET	(256 * 1024)
+#define CONFIG_ENV_SIZE	(16 * 1024)
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_CMD_SAVEENV
+#ifdef	CONFIG_CMD_MMC
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_MXS_MMC
+#endif
+
+/*
+ * Ethernet on SOC (FEC)
+ */
+#ifdef	CONFIG_CMD_NET
+#define CONFIG_NET_MULTI
+#define CONFIG_ETHPRIME	"FEC0"
+#define CONFIG_FEC_MXC
+#define CONFIG_FEC_MXC_MULTI
+#define CONFIG_MII
+#define CONFIG_DISCOVER_PHY
+#define CONFIG_FEC_XCV_TYPE	RMII
+#define CONFIG_MX28_FEC_MAC_IN_OCOTP
+#endif
+
+/*
+ * Boot Linux
+ */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_BOOTDELAY	3
+#define CONFIG_BOOTFILE	"uImage"
+#define CONFIG_BOOTCOMMAND	"run bootcmd_net"
+#define CONFIG_LOADADDR	0x42000000
+#define CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR
+
+/*
+ * Extra Environments
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"console_fsl=console=ttyAM0" \
+	"console_mainline=console=ttyAMA0" \
+	"netargs=setenv bootargs console=${console_mainline}" \
+		"root=/dev/nfs " \
+		"ip=dhcp nfsroot=${serverip}:${nfsroot}\0" \
+	"bootcmd_net=echo Booting from net ...; " \
+		"run netargs; " \
+		"dhcp ${uimage}; bootm\0" \
+
+#endif /* __CONFIG_H */
-- 
1.7.1

[U-Boot] [PATCH v7 2/4] mx28: Let imx_get_mac_from_fuse be common for mx28

[Marek Vasut]

> Let imx_get_mac_from_fuse function be a common function, so that other
> mx28 boards can reuse it.
> 
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> ---
> Changes since v6:
> - Let mac[5] be set inside mx28_adjust_mac
> Changes since v5:
> - Allow the MAC vendor to be overriden
> Changes since v4:
> - No changes
> Change since v3:
> - Add a note about the first two MAC addresses being from Freescale vendor.
>  arch/arm/cpu/arm926ejs/mx28/mx28.c |   46
> ++++++++++++++++++++++++++++++++++++ board/denx/m28evk/m28evk.c         | 
>  35 --------------------------- 2 files changed, 46 insertions(+), 35
> deletions(-)
> 
> diff --git a/arch/arm/cpu/arm926ejs/mx28/mx28.c
> b/arch/arm/cpu/arm926ejs/mx28/mx28.c index 088c019..ee4e337 100644
> --- a/arch/arm/cpu/arm926ejs/mx28/mx28.c
> +++ b/arch/arm/cpu/arm926ejs/mx28/mx28.c
> @@ -214,6 +214,52 @@ int cpu_eth_init(bd_t *bis)
>  }
>  #endif
> 
> +static void __mx28_adjust_mac(int dev_id, char *mac)

unsigned char * ... see the header file in your previous patch ;-)

> +{
> +	mac[0] = 0x00;
> +	mac[1] = 0x04; /* Use FSL vendor MAC address by default */
> +
> +	if (dev_id == 1) /* Let MAC1 be MAC0 + 1 by default */
> +		mac[5] += 1;
> +}
> +
> +void mx28_adjust_mac(int dev_id, char *mac)
> +	__attribute__((weak, alias("__mx28_adjust_mac")));
> +
> +#ifdef	CONFIG_MX28_FEC_MAC_IN_OCOTP
> +
> +#define	MXS_OCOTP_MAX_TIMEOUT	1000000
> +void imx_get_mac_from_fuse(int dev_id, char *mac)

DTTO

> +{
> +	struct mx28_ocotp_regs *ocotp_regs =
> +		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
> +	uint32_t data;
> +
> +	memset(mac, 0, 6);
> +
> +	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
> +
> +	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
> +				MXS_OCOTP_MAX_TIMEOUT)) {
> +		printf("MXS FEC: Can't get MAC from OCOTP\n");
> +		return;
> +	}
> +
> +	data = readl(&ocotp_regs->hw_ocotp_cust0);
> +
> +	mac[2] = (data >> 24) & 0xff;
> +	mac[3] = (data >> 16) & 0xff;
> +	mac[4] = (data >> 8) & 0xff;
> +	mac[5] = data & 0xff;
> +	mx28_adjust_mac(dev_id, mac);
> +}
> +#else
> +void imx_get_mac_from_fuse(int dev_id, char *mac)

DTTO

> +{
> +	memset(mac, 0, 6);
> +}
> +#endif
> +
>  U_BOOT_CMD(
>  	clocks,	CONFIG_SYS_MAXARGS, 1, do_mx28_showclocks,
>  	"display clocks",
> diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
> index a0fabc0..005446a 100644
> --- a/board/denx/m28evk/m28evk.c
> +++ b/board/denx/m28evk/m28evk.c
> @@ -178,39 +178,4 @@ int board_eth_init(bd_t *bis)
>  	return ret;
>  }
> 
> -#ifdef	CONFIG_M28_FEC_MAC_IN_OCOTP
> -
> -#define	MXS_OCOTP_MAX_TIMEOUT	1000000
> -void imx_get_mac_from_fuse(int dev_id, char *mac)
> -{
> -	struct mx28_ocotp_regs *ocotp_regs =
> -		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
> -	uint32_t data;
> -
> -	memset(mac, 0, 6);
> -
> -	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
> -
> -	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
> -				MXS_OCOTP_MAX_TIMEOUT)) {
> -		printf("MXS FEC: Can't get MAC from OCOTP\n");
> -		return;
> -	}
> -
> -	data = readl(&ocotp_regs->hw_ocotp_cust0);
> -
> -	mac[0] = 0x00;
> -	mac[1] = 0x04;
> -	mac[2] = (data >> 24) & 0xff;
> -	mac[3] = (data >> 16) & 0xff;
> -	mac[4] = (data >> 8) & 0xff;
> -	mac[5] = data & 0xff;
> -}
> -#else
> -void imx_get_mac_from_fuse(int dev_id, char *mac)
> -{
> -	memset(mac, 0, 6);
> -}
> -#endif
> -
>  #endif

M

[U-Boot] [PATCH v8 2/4] mx28: Let imx_get_mac_from_fuse be common for mx28

[Fabio Estevam]

Let imx_get_mac_from_fuse function be a common function, so that other
mx28 boards can reuse it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
Changes since v7:
- Use unsigned char instead of char
Changes since v6:
- Let mac[5] be set inside mx28_adjust_mac
Changes since v5:
- Allow the MAC vendor to be overriden
Changes since v4:
- No changes
Change since v3:
- Add a note about the first two MAC addresses being from Freescale vendor.
 arch/arm/cpu/arm926ejs/mx28/mx28.c |   46 ++++++++++++++++++++++++++++++++++++
 board/denx/m28evk/m28evk.c         |   35 ---------------------------
 2 files changed, 46 insertions(+), 35 deletions(-)

diff --git a/arch/arm/cpu/arm926ejs/mx28/mx28.c b/arch/arm/cpu/arm926ejs/mx28/mx28.c
index 088c019..ee4e337 100644
--- a/arch/arm/cpu/arm926ejs/mx28/mx28.c
+++ b/arch/arm/cpu/arm926ejs/mx28/mx28.c
@@ -214,6 +214,52 @@ int cpu_eth_init(bd_t *bis)
 }
 #endif
 
+static void __mx28_adjust_mac(int dev_id, unsigned char *mac)
+{
+	mac[0] = 0x00;
+	mac[1] = 0x04; /* Use FSL vendor MAC address by default */
+
+	if (dev_id == 1) /* Let MAC1 be MAC0 + 1 by default */
+		mac[5] += 1;
+}
+
+void mx28_adjust_mac(int dev_id, unsigned char *mac)
+	__attribute__((weak, alias("__mx28_adjust_mac")));
+
+#ifdef	CONFIG_MX28_FEC_MAC_IN_OCOTP
+
+#define	MXS_OCOTP_MAX_TIMEOUT	1000000
+void imx_get_mac_from_fuse(int dev_id, unsigned char *mac)
+{
+	struct mx28_ocotp_regs *ocotp_regs =
+		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
+	uint32_t data;
+
+	memset(mac, 0, 6);
+
+	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
+
+	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
+				MXS_OCOTP_MAX_TIMEOUT)) {
+		printf("MXS FEC: Can't get MAC from OCOTP\n");
+		return;
+	}
+
+	data = readl(&ocotp_regs->hw_ocotp_cust0);
+
+	mac[2] = (data >> 24) & 0xff;
+	mac[3] = (data >> 16) & 0xff;
+	mac[4] = (data >> 8) & 0xff;
+	mac[5] = data & 0xff;
+	mx28_adjust_mac(dev_id, mac);
+}
+#else
+void imx_get_mac_from_fuse(int dev_id, unsigned char *mac)
+{
+	memset(mac, 0, 6);
+}
+#endif
+
 U_BOOT_CMD(
 	clocks,	CONFIG_SYS_MAXARGS, 1, do_mx28_showclocks,
 	"display clocks",
diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
index a0fabc0..005446a 100644
--- a/board/denx/m28evk/m28evk.c
+++ b/board/denx/m28evk/m28evk.c
@@ -178,39 +178,4 @@ int board_eth_init(bd_t *bis)
 	return ret;
 }
 
-#ifdef	CONFIG_M28_FEC_MAC_IN_OCOTP
-
-#define	MXS_OCOTP_MAX_TIMEOUT	1000000
-void imx_get_mac_from_fuse(int dev_id, char *mac)
-{
-	struct mx28_ocotp_regs *ocotp_regs =
-		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
-	uint32_t data;
-
-	memset(mac, 0, 6);
-
-	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
-
-	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
-				MXS_OCOTP_MAX_TIMEOUT)) {
-		printf("MXS FEC: Can't get MAC from OCOTP\n");
-		return;
-	}
-
-	data = readl(&ocotp_regs->hw_ocotp_cust0);
-
-	mac[0] = 0x00;
-	mac[1] = 0x04;
-	mac[2] = (data >> 24) & 0xff;
-	mac[3] = (data >> 16) & 0xff;
-	mac[4] = (data >> 8) & 0xff;
-	mac[5] = data & 0xff;
-}
-#else
-void imx_get_mac_from_fuse(int dev_id, char *mac)
-{
-	memset(mac, 0, 6);
-}
-#endif
-
 #endif
-- 
1.7.1

[U-Boot] [PATCH v8 2/4] mx28: Let imx_get_mac_from_fuse be common for mx28

[Marek Vasut]

> Let imx_get_mac_from_fuse function be a common function, so that other
> mx28 boards can reuse it.
> 
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> ---
> Changes since v7:
> - Use unsigned char instead of char
> Changes since v6:
> - Let mac[5] be set inside mx28_adjust_mac
> Changes since v5:
> - Allow the MAC vendor to be overriden
> Changes since v4:
> - No changes
> Change since v3:
> - Add a note about the first two MAC addresses being from Freescale vendor.
>  arch/arm/cpu/arm926ejs/mx28/mx28.c |   46
> ++++++++++++++++++++++++++++++++++++ board/denx/m28evk/m28evk.c         | 
>  35 --------------------------- 2 files changed, 46 insertions(+), 35
> deletions(-)
> 
> diff --git a/arch/arm/cpu/arm926ejs/mx28/mx28.c
> b/arch/arm/cpu/arm926ejs/mx28/mx28.c index 088c019..ee4e337 100644
> --- a/arch/arm/cpu/arm926ejs/mx28/mx28.c
> +++ b/arch/arm/cpu/arm926ejs/mx28/mx28.c
> @@ -214,6 +214,52 @@ int cpu_eth_init(bd_t *bis)
>  }
>  #endif
> 
> +static void __mx28_adjust_mac(int dev_id, unsigned char *mac)
> +{
> +	mac[0] = 0x00;
> +	mac[1] = 0x04; /* Use FSL vendor MAC address by default */
> +
> +	if (dev_id == 1) /* Let MAC1 be MAC0 + 1 by default */
> +		mac[5] += 1;
> +}
> +
> +void mx28_adjust_mac(int dev_id, unsigned char *mac)
> +	__attribute__((weak, alias("__mx28_adjust_mac")));
> +
> +#ifdef	CONFIG_MX28_FEC_MAC_IN_OCOTP
> +
> +#define	MXS_OCOTP_MAX_TIMEOUT	1000000
> +void imx_get_mac_from_fuse(int dev_id, unsigned char *mac)
> +{
> +	struct mx28_ocotp_regs *ocotp_regs =
> +		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
> +	uint32_t data;
> +
> +	memset(mac, 0, 6);
> +
> +	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
> +
> +	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
> +				MXS_OCOTP_MAX_TIMEOUT)) {
> +		printf("MXS FEC: Can't get MAC from OCOTP\n");
> +		return;
> +	}
> +
> +	data = readl(&ocotp_regs->hw_ocotp_cust0);
> +
> +	mac[2] = (data >> 24) & 0xff;
> +	mac[3] = (data >> 16) & 0xff;
> +	mac[4] = (data >> 8) & 0xff;
> +	mac[5] = data & 0xff;
> +	mx28_adjust_mac(dev_id, mac);
> +}
> +#else
> +void imx_get_mac_from_fuse(int dev_id, unsigned char *mac)
> +{
> +	memset(mac, 0, 6);
> +}
> +#endif
> +
>  U_BOOT_CMD(
>  	clocks,	CONFIG_SYS_MAXARGS, 1, do_mx28_showclocks,
>  	"display clocks",
> diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
> index a0fabc0..005446a 100644
> --- a/board/denx/m28evk/m28evk.c
> +++ b/board/denx/m28evk/m28evk.c
> @@ -178,39 +178,4 @@ int board_eth_init(bd_t *bis)
>  	return ret;
>  }
> 
> -#ifdef	CONFIG_M28_FEC_MAC_IN_OCOTP
> -
> -#define	MXS_OCOTP_MAX_TIMEOUT	1000000
> -void imx_get_mac_from_fuse(int dev_id, char *mac)
> -{
> -	struct mx28_ocotp_regs *ocotp_regs =
> -		(struct mx28_ocotp_regs *)MXS_OCOTP_BASE;
> -	uint32_t data;
> -
> -	memset(mac, 0, 6);
> -
> -	writel(OCOTP_CTRL_RD_BANK_OPEN, &ocotp_regs->hw_ocotp_ctrl_set);
> -
> -	if (mx28_wait_mask_clr(&ocotp_regs->hw_ocotp_ctrl_reg, OCOTP_CTRL_BUSY,
> -				MXS_OCOTP_MAX_TIMEOUT)) {
> -		printf("MXS FEC: Can't get MAC from OCOTP\n");
> -		return;
> -	}
> -
> -	data = readl(&ocotp_regs->hw_ocotp_cust0);
> -
> -	mac[0] = 0x00;
> -	mac[1] = 0x04;
> -	mac[2] = (data >> 24) & 0xff;
> -	mac[3] = (data >> 16) & 0xff;
> -	mac[4] = (data >> 8) & 0xff;
> -	mac[5] = data & 0xff;
> -}
> -#else
> -void imx_get_mac_from_fuse(int dev_id, char *mac)
> -{
> -	memset(mac, 0, 6);
> -}
> -#endif
> -
>  #endif

Acked-by: Marek Vasut <marek.vasut@gmail.com>

[U-Boot] [PATCH v8 2/4] mx28: Let imx_get_mac_from_fuse be common for mx28

[Stefano Babic]

On 20/12/2011 17:42, Fabio Estevam wrote:
> Let imx_get_mac_from_fuse function be a common function, so that other
> mx28 boards can reuse it.
> 
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> ---

Applied to u-boot-imx, thanks.

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================

[U-Boot] [PATCH v7 3/4] mx28: Let dram_init be common for mx28

[Stefano Babic]

On 20/12/2011 16:46, Fabio Estevam wrote:
> Let dram_init function be a common function, so that other mx28 boards
> can reuse it.
> 
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> Acked-by: Marek Vasut <marek.vasut@gmail.com>
> ---

Applied to u-boot-imx, thanks.

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================

[U-Boot] [PATCH v7 1/4] net: imx: Add multi-FEC support for imx_get_mac_from_fuse

[Stefano Babic]

On 20/12/2011 16:46, Fabio Estevam wrote:
> Add multi-FEC support for imx_get_mac_from_fuse by passing dev_id as a parameter.
> 
> This feature is important on mx28 SoC for example that has two FEC ports.
> 
> Cc: Ben Warren <biggerbadderben@gmail.com>
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> ---

Applied to u-boot-imx, thanks.

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================

[U-Boot] [PATCH v7 2/4] mx28: Let imx_get_mac_from_fuse be common for mx28

[Stefano Babic]

On 20/12/2011 16:46, Fabio Estevam wrote:
> Let imx_get_mac_from_fuse function be a common function, so that other
> mx28 boards can reuse it.
> 
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> ---


Applied to u-boot-imx, thanks.

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================