From: Eric Nelson <eric.nelson@boundarydevices.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 2/6] mx6q: Add support for ECSPI through mxc_spi driver
Date: Tue, 17 Jan 2012 18:44:59 -0700 [thread overview]
Message-ID: <4F16241B.5050007@boundarydevices.com> (raw)
In-Reply-To: <201201180227.17414.marek.vasut@gmail.com>
On 01/17/2012 06:27 PM, Marek Vasut wrote:
>> On 01/17/2012 04:19 PM, Marek Vasut wrote:
>>>> Signed-off-by: Eric Nelson<eric.nelson@boundarydevices.com>
>>>> +/* ECSPI registers */
>>>> +struct cspi_regs {
>>>> + u32 rxdata;
>>>> + u32 txdata;
>>>> + u32 ctrl;
>>>> + u32 cfg;
>>>> + u32 intr;
>>>> + u32 dma;
>>>> + u32 stat;
>>>> + u32 period;
>>>> +};
>>>
>>> Sigh ... it's no fun I can have only one remark :-)
>>>
>>> Is this part common for all imx-es ?
>>
>> All i.MX6's
>>
>> This is a cut& paste from MX51.
>>
>> I was tempted to introduce an 'mxc_ecspi.h' to merge the declaration
>> for i.MX5x and i.MX6 which share the ECSPI peripheral and 'mxc_cspi.h'
>> for i.MX31 and i.MX35 that share the CSPI peripheral.
>
> But you don't even need this outside of the spi driver so just put it into the
> spi driver and be done with it. That'll solve your duplication issue.
>
> M
>
I'll defer to Stefano on this one, since I did this in response
to his request:
> Right - and we already discussed in the past how to avoid to put
> specific SOC code inside the driver. In fact, the cspi_regs structure
> was already moved into the specific SOC header (imx-regs.h) - but the
> definitions of the single bits of the registers are still inside the
> driver, as well as the base address of the (e)cspi controllers.
>
> They should also be moved - take into acoount by implementing your
> changes for i.mx6
The struct cspi_regs is already present in mx31, mx35, and mx51 headers,
so I'm not breaking new ground here, only in the bitfield declarations.
http://git.denx.de/?p=u-boot.git;a=blob;f=arch/arm/include/asm/arch-mx31/imx-regs.h;h=6a517ddd931ca0d1e598bd7456c4c611741602eb;hb=HEAD#l60
http://git.denx.de/?p=u-boot.git;a=blob;f=arch/arm/include/asm/arch-mx35/imx-regs.h;h=df74508a93ee87ae986f7c2f48f6c5fb36626070;hb=HEAD#l279
http://git.denx.de/?p=u-boot.git;a=blob;f=arch/arm/include/asm/arch-mx5/imx-regs.h;h=0ee88d25b7800ae9e6aed809d02dd19d9cac9c82;hb=HEAD#l423
My interpretation of Stefano's intent is to clean up the driver at the expense
of extra defines in the arch-specific headers.
Regards,
Eric
next prev parent reply other threads:[~2012-01-18 1:44 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-01-17 22:09 [U-Boot] mxc_spi refactoring (for mx6q) Eric Nelson
2012-01-17 22:09 ` [U-Boot] [PATCH 1/6] mxc_spi: move machine specifics into CPU headers Eric Nelson
2012-01-17 22:09 ` [U-Boot] [PATCH 2/6] mx6q: Add support for ECSPI through mxc_spi driver Eric Nelson
2012-01-17 23:19 ` Marek Vasut
2012-01-18 0:36 ` Eric Nelson
2012-01-18 1:27 ` Marek Vasut
2012-01-18 1:44 ` Eric Nelson [this message]
2012-01-18 1:47 ` Marek Vasut
2012-01-18 2:02 ` Eric Nelson
2012-01-18 8:39 ` Stefano Babic
2012-01-18 16:08 ` Marek Vasut
2012-01-18 16:41 ` Stefano Babic
2012-01-18 20:05 ` Eric Nelson
2012-01-19 10:33 ` Stefano Babic
2012-01-17 22:09 ` [U-Boot] [PATCH 3/6] mx6q: mx6qsabrelite: Add ECSPI support to the Sabrelite platform Eric Nelson
2012-01-17 22:09 ` [U-Boot] [PATCH 4/6] sf command: allow default chip select through CONFIG_SPI_FLASH_CS Eric Nelson
2012-01-17 22:09 ` [U-Boot] [PATCH 5/6] mx6q: mx6qsabrelite: Provide default chip-select for serial flash Eric Nelson
2012-01-17 22:09 ` [U-Boot] [PATCH 6/6] mx6q: mx6qsabrelite: Provide defaults for placing environment in " Eric Nelson
2012-01-20 3:27 ` Jason Hui
2012-01-20 7:06 ` Dirk Behme
2012-01-20 7:48 ` Jason Hui
2012-01-20 8:47 ` Stefano Babic
2012-01-20 13:47 ` Eric Nelson
2012-01-20 13:43 ` Eric Nelson
2012-01-17 23:16 ` [U-Boot] mxc_spi refactoring (for mx6q) Marek Vasut
2012-01-18 11:51 ` Dirk Behme
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4F16241B.5050007@boundarydevices.com \
--to=eric.nelson@boundarydevices.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox