[U-Boot] [PATCH V4 3/8] imx: fec: Resolve speed before configuring gasket

[Troy Kisky <troy.kisky@boundarydevices.com>]

On 4/19/2012 1:55 AM, Timo Ketola wrote:
> Gasket needs a different configuration for 10BaseT than for higher
> speeds.
>
> Signed-off-by: Timo Ketola<timo@exertus.fi>
> ---
>
> Changes in v4:
> - Rewrapped commit message
>
> Changes in v2:
> - Dropped patches 2 and 3 so this one changed from 5 to 3
> - Rebased to u-boot-imx next
> - Removed the remove of 'miiphy_duplex' call
> - Changed 'speed == _100BASET' to 'speed != _10BASET' to not to break
>      _1000BASET
> - Changed configuration option to put gasket into RMII mode from
>      !CONFIG_MII to CONFIG_RMII. I'm not too sure how this should be
>      done though. !CONFIG_MII is normally used for this but its original
>      purpose was to enable MII *management* interface, I think...
>
>   drivers/net/fec_mxc.c |   43 ++++++++++++++++++++++++-------------------
>   1 files changed, 24 insertions(+), 19 deletions(-)
>
> diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c
> index 824a199..48a69d4 100644
> --- a/drivers/net/fec_mxc.c
> +++ b/drivers/net/fec_mxc.c
> @@ -440,6 +440,22 @@ static int fec_open(struct eth_device *edev)
>   	 */
>   	writel(readl(&fec->eth->ecntrl) | FEC_ECNTRL_ETHER_EN,
>   		&fec->eth->ecntrl);
> +#ifdef CONFIG_PHYLIB
> +	if (!fec->phydev)
> +		fec_eth_phy_config(edev);
> +	if (fec->phydev) {
> +		/* Start up the PHY */
> +		phy_startup(fec->phydev);
> +		speed = fec->phydev->speed;
> +	} else {
> +		speed = _100BASET;
> +	}
> +#else
> +	miiphy_wait_aneg(edev);
> +	speed = miiphy_speed(edev->name, fec->phy_id);
> +	miiphy_duplex(edev->name, fec->phy_id);
> +#endif
> +
>   #if defined(CONFIG_MX25) || defined(CONFIG_MX53)
>   	udelay(100);
>   	/*
> @@ -453,9 +469,14 @@ static int fec_open(struct eth_device *edev)
>   	while (readw(&fec->eth->miigsk_enr)&  MIIGSK_ENR_READY)
>   		udelay(2);
>
> -#if !defined(CONFIG_MII)
> -	/* configure gasket for RMII, 50 MHz, no loopback, and no echo */
> -	writew(MIIGSK_CFGR_IF_MODE_RMII,&fec->eth->miigsk_cfgr);
> +#if defined(CONFIG_RMII)
> +	if (speed != _10BASET)
> +		/* configure gasket for RMII, 50MHz, no loopback, and no echo */
> +		writew(MIIGSK_CFGR_IF_MODE_RMII,&fec->eth->miigsk_cfgr);
> +	else
> +		/* configure gasket for RMII, 5MHz, no loopback, and no echo */
> +		writew(MIIGSK_CFGR_IF_MODE_RMII | MIIGSK_CFGR_FRCONT,
> +				&fec->eth->miigsk_cfgr);
>   #else
>   	/* configure gasket for MII, no loopback, and no echo */
>   	writew(MIIGSK_CFGR_IF_MODE_MII,&fec->eth->miigsk_cfgr);
> @@ -474,22 +495,6 @@ static int fec_open(struct eth_device *edev)
>   	}
>   #endif
>

Can you fix 10BASET for non-reduced pin count boards as well?

Thanks
Troy