* [U-Boot] [PATCH 2/6] mx35pdk: Remove CONFIG_SYS_I2C_SLAVE definition
2012-06-03 7:53 [U-Boot] [PATCH 1/6] imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition Fabio Estevam
@ 2012-06-03 7:53 ` Fabio Estevam
2012-06-03 7:53 ` [U-Boot] [PATCH 3/6] mx53ard: " Fabio Estevam
` (4 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Fabio Estevam @ 2012-06-03 7:53 UTC (permalink / raw)
To: u-boot
From: Fabio Estevam <fabio.estevam@freescale.com>
According to include/i2c.h:
"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"
As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
include/configs/mx35pdk.h | 1 -
1 files changed, 0 insertions(+), 1 deletions(-)
diff --git a/include/configs/mx35pdk.h b/include/configs/mx35pdk.h
index bd57baa..5f75018 100644
--- a/include/configs/mx35pdk.h
+++ b/include/configs/mx35pdk.h
@@ -59,7 +59,6 @@
#define CONFIG_I2C_MXC
#define CONFIG_SYS_I2C_MX35_PORT1
#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 0xfe
#define CONFIG_MXC_SPI
#define CONFIG_MXC_GPIO
--
1.7.1
^ permalink raw reply related [flat|nested] 7+ messages in thread* [U-Boot] [PATCH 3/6] mx53ard: Remove CONFIG_SYS_I2C_SLAVE definition
2012-06-03 7:53 [U-Boot] [PATCH 1/6] imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition Fabio Estevam
2012-06-03 7:53 ` [U-Boot] [PATCH 2/6] mx35pdk: " Fabio Estevam
@ 2012-06-03 7:53 ` Fabio Estevam
2012-06-03 7:53 ` [U-Boot] [PATCH 4/6] mx53evk: " Fabio Estevam
` (3 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Fabio Estevam @ 2012-06-03 7:53 UTC (permalink / raw)
To: u-boot
According to include/i2c.h:
"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"
As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
include/configs/mx53ard.h | 1 -
1 files changed, 0 insertions(+), 1 deletions(-)
diff --git a/include/configs/mx53ard.h b/include/configs/mx53ard.h
index f48a41e..f879edc 100644
--- a/include/configs/mx53ard.h
+++ b/include/configs/mx53ard.h
@@ -52,7 +52,6 @@
#define CONFIG_I2C_MXC
#define CONFIG_SYS_I2C_MX53_PORT2
#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 0xfe
/* MMC Configs */
#define CONFIG_FSL_ESDHC
--
1.7.1
^ permalink raw reply related [flat|nested] 7+ messages in thread* [U-Boot] [PATCH 4/6] mx53evk: Remove CONFIG_SYS_I2C_SLAVE definition
2012-06-03 7:53 [U-Boot] [PATCH 1/6] imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition Fabio Estevam
2012-06-03 7:53 ` [U-Boot] [PATCH 2/6] mx35pdk: " Fabio Estevam
2012-06-03 7:53 ` [U-Boot] [PATCH 3/6] mx53ard: " Fabio Estevam
@ 2012-06-03 7:53 ` Fabio Estevam
2012-06-03 7:53 ` [U-Boot] [PATCH 5/6] mx53loco: " Fabio Estevam
` (2 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Fabio Estevam @ 2012-06-03 7:53 UTC (permalink / raw)
To: u-boot
From: Fabio Estevam <fabio.estevam@freescale.com>
According to include/i2c.h:
"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"
As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
include/configs/mx53evk.h | 1 -
1 files changed, 0 insertions(+), 1 deletions(-)
diff --git a/include/configs/mx53evk.h b/include/configs/mx53evk.h
index a77e5b2..2acefe9 100644
--- a/include/configs/mx53evk.h
+++ b/include/configs/mx53evk.h
@@ -55,7 +55,6 @@
#define CONFIG_I2C_MXC
#define CONFIG_SYS_I2C_MX53_PORT2 1
#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 0xfe
/* PMIC Configs */
#define CONFIG_PMIC
--
1.7.1
^ permalink raw reply related [flat|nested] 7+ messages in thread* [U-Boot] [PATCH 5/6] mx53loco: Remove CONFIG_SYS_I2C_SLAVE definition
2012-06-03 7:53 [U-Boot] [PATCH 1/6] imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition Fabio Estevam
` (2 preceding siblings ...)
2012-06-03 7:53 ` [U-Boot] [PATCH 4/6] mx53evk: " Fabio Estevam
@ 2012-06-03 7:53 ` Fabio Estevam
2012-06-03 7:53 ` [U-Boot] [PATCH 6/6] mx53smd: " Fabio Estevam
2012-06-15 14:43 ` [U-Boot] [PATCH 1/6] imx31_phycore: " Stefano Babic
5 siblings, 0 replies; 7+ messages in thread
From: Fabio Estevam @ 2012-06-03 7:53 UTC (permalink / raw)
To: u-boot
From: Fabio Estevam <fabio.estevam@freescale.com>
According to include/i2c.h:
"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"
As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
include/configs/mx53loco.h | 1 -
1 files changed, 0 insertions(+), 1 deletions(-)
diff --git a/include/configs/mx53loco.h b/include/configs/mx53loco.h
index 7d782e2..7c45647 100644
--- a/include/configs/mx53loco.h
+++ b/include/configs/mx53loco.h
@@ -92,7 +92,6 @@
#define CONFIG_I2C_MXC
#define CONFIG_SYS_I2C_MX53_PORT1
#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 0xfe
/* PMIC Controller */
#define CONFIG_PMIC
--
1.7.1
^ permalink raw reply related [flat|nested] 7+ messages in thread* [U-Boot] [PATCH 6/6] mx53smd: Remove CONFIG_SYS_I2C_SLAVE definition
2012-06-03 7:53 [U-Boot] [PATCH 1/6] imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition Fabio Estevam
` (3 preceding siblings ...)
2012-06-03 7:53 ` [U-Boot] [PATCH 5/6] mx53loco: " Fabio Estevam
@ 2012-06-03 7:53 ` Fabio Estevam
2012-06-15 14:43 ` [U-Boot] [PATCH 1/6] imx31_phycore: " Stefano Babic
5 siblings, 0 replies; 7+ messages in thread
From: Fabio Estevam @ 2012-06-03 7:53 UTC (permalink / raw)
To: u-boot
From: Fabio Estevam <fabio.estevam@freescale.com>
According to include/i2c.h:
"/*
* Many boards/controllers/drivers don't support an I2C slave interface so
* provide a default slave address for them for use in common code. A real
* value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
* support a slave interface.
*/
#ifndef CONFIG_SYS_I2C_SLAVE
#define CONFIG_SYS_I2C_SLAVE 0xfe
#endif
"
As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
include/configs/mx53smd.h | 1 -
1 files changed, 0 insertions(+), 1 deletions(-)
diff --git a/include/configs/mx53smd.h b/include/configs/mx53smd.h
index a04db3f..61edd7f 100644
--- a/include/configs/mx53smd.h
+++ b/include/configs/mx53smd.h
@@ -52,7 +52,6 @@
#define CONFIG_I2C_MXC
#define CONFIG_SYS_I2C_MX53_PORT2
#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 0xfe
/* MMC Configs */
#define CONFIG_FSL_ESDHC
--
1.7.1
^ permalink raw reply related [flat|nested] 7+ messages in thread* [U-Boot] [PATCH 1/6] imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition
2012-06-03 7:53 [U-Boot] [PATCH 1/6] imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition Fabio Estevam
` (4 preceding siblings ...)
2012-06-03 7:53 ` [U-Boot] [PATCH 6/6] mx53smd: " Fabio Estevam
@ 2012-06-15 14:43 ` Stefano Babic
5 siblings, 0 replies; 7+ messages in thread
From: Stefano Babic @ 2012-06-15 14:43 UTC (permalink / raw)
To: u-boot
On 03/06/2012 09:53, Fabio Estevam wrote:
> From: Fabio Estevam <fabio.estevam@freescale.com>
>
> According to include/i2c.h:
>
> "/*
> * Many boards/controllers/drivers don't support an I2C slave interface so
> * provide a default slave address for them for use in common code. A real
> * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
> * support a slave interface.
> */
> #ifndef CONFIG_SYS_I2C_SLAVE
> #define CONFIG_SYS_I2C_SLAVE 0xfe
> #endif
Whole series applied to u-boot-imx, thanks.
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 7+ messages in thread