[U-Boot] [PATCH v4] tx25: Use generic gpio_* calls

[Vikram Narayanan <vikram186@gmail.com>]

Instead of manipulating gpio registers directly, use the calls
from the gpio library.

Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
---
Changes from v3:
Use gpio_set_value instead of gpio_direction_output
(Ahh. Missed it again!!. Very bad)

Changes from v2:
Swap the place of the change log and commit message.

Changes from v1:
Used appropriate gpio_* lib calls.

 board/karo/tx25/tx25.c |   25 +++++++++----------------
 1 files changed, 9 insertions(+), 16 deletions(-)

diff --git a/board/karo/tx25/tx25.c b/board/karo/tx25/tx25.c
index 2a29943..07fd98d 100644
--- a/board/karo/tx25/tx25.c
+++ b/board/karo/tx25/tx25.c
@@ -34,14 +34,13 @@
 DECLARE_GLOBAL_DATA_PTR;
 
 #ifdef CONFIG_FEC_MXC
+#define GPIO_FEC_RESET_B	MXC_GPIO_PORT_TO_NUM(4, 7)
+#define GPIO_FEC_ENABLE_B	MXC_GPIO_PORT_TO_NUM(4, 9)
 void tx25_fec_init(void)
 {
 	struct iomuxc_mux_ctl *muxctl;
 	struct iomuxc_pad_ctl *padctl;
-	u32 val;
 	u32 gpio_mux_mode = MX25_PIN_MUX_MODE(5);
-	struct gpio_regs *gpio4 = (struct gpio_regs *)IMX_GPIO4_BASE;
-	struct gpio_regs *gpio3 = (struct gpio_regs *)IMX_GPIO3_BASE;
 	u32 saved_rdata0_mode, saved_rdata1_mode, saved_rx_dv_mode;
 
 	debug("tx25_fec_init\n");
@@ -66,18 +65,15 @@ void tx25_fec_init(void)
 	writel(0x0, &padctl->pad_d11);
 
 	/* drop PHY power and assert reset (low) */
-	val = readl(&gpio4->gpio_dr) & ~((1 << 7) | (1 << 9));
-	writel(val, &gpio4->gpio_dr);
-	val = readl(&gpio4->gpio_dir) | (1 << 7) | (1 << 9);
-	writel(val, &gpio4->gpio_dir);
+	gpio_direction_output(GPIO_FEC_RESET_B, 0);
+	gpio_direction_output(GPIO_FEC_ENABLE_B, 0);
 
 	mdelay(5);
 
 	debug("resetting phy\n");
 
 	/* turn on PHY power leaving reset asserted */
-	val = readl(&gpio4->gpio_dr) | 1 << 9;
-	writel(val, &gpio4->gpio_dr);
+	gpio_set_value(GPIO_FEC_ENABLE_B, 1);
 
 	mdelay(10);
 
@@ -107,19 +103,16 @@ void tx25_fec_init(void)
 	/*
 	 * set each to 1 and make each an output
 	 */
-	val = readl(&gpio3->gpio_dr) | (1 << 10) | (1 << 11) | (1 << 12);
-	writel(val, &gpio3->gpio_dr);
-	val = readl(&gpio3->gpio_dir) | (1 << 10) | (1 << 11) | (1 << 12);
-	writel(val, &gpio3->gpio_dir);
+	gpio_direction_output(MXC_GPIO_PORT_TO_NUM(3, 10), 1);
+	gpio_direction_output(MXC_GPIO_PORT_TO_NUM(3, 11), 1);
+	gpio_direction_output(MXC_GPIO_PORT_TO_NUM(3, 12), 1);
 
 	mdelay(22);		/* this value came from RedBoot */
 
 	/*
 	 * deassert PHY reset
 	 */
-	val = readl(&gpio4->gpio_dr) | 1 << 7;
-	writel(val, &gpio4->gpio_dr);
-	writel(val, &gpio4->gpio_dr);
+	gpio_set_value(GPIO_FEC_RESET_B, 1);
 
 	mdelay(5);
 
-- 
1.7.4.1