[U-Boot] [PATCH 06/12] microblaze: intc: Add device-tree driver configuration

[Michal Simek <monstr@monstr.eu>]

On 07/09/2012 11:26 PM, Simon Glass wrote:
> Hi Michal,
>
> On Mon, Jul 9, 2012 at 2:20 AM, Michal Simek <monstr at monstr.eu <mailto:monstr@monstr.eu>> wrote:
>
>     Read configuration from DTB.
>
>     Signed-off-by: Michal Simek <monstr at monstr.eu <mailto:monstr@monstr.eu>>
>     ---
>       arch/microblaze/cpu/interrupts.c |   19 +++++++++++++++++++
>       1 files changed, 19 insertions(+), 0 deletions(-)
>
>     diff --git a/arch/microblaze/cpu/interrupts.c b/arch/microblaze/cpu/interrupts.c
>     index 79ee96a..98c9110 100644
>     --- a/arch/microblaze/cpu/interrupts.c
>     +++ b/arch/microblaze/cpu/interrupts.c
>     @@ -29,6 +29,9 @@
>       #include <malloc.h>
>       #include <asm/microblaze_intc.h>
>       #include <asm/asm.h>
>     +#include <fdtdec.h>
>     +
>     +DECLARE_GLOBAL_DATA_PTR;
>
>       #undef DEBUG_INT
>
>     @@ -134,10 +137,26 @@ int interrupts_init(void)
>       {
>              int i;
>
>     +#ifndef CONFIG_OF_CONTROL
>       #if defined(CONFIG_SYS_INTC_0_ADDR) && defined(CONFIG_SYS_INTC_0_NUM)
>              intc = (microblaze_intc_t *) (CONFIG_SYS_INTC_0_ADDR);
>              irq_no = CONFIG_SYS_INTC_0_NUM;
>       #endif
>     +#else
>     +       int temp;
>     +       int offset = 0;
>
>
> I don't think you need the = 0.

Agree. Will remove it.

>
>     +
>     +       offset = fdt_node_offset_by_compatible(gd->fdt_blob, offset,
>     + "xlnx,xps-intc-1.00.a");
>     +       if (offset > 0) {
>     +               temp = fdtdec_get_addr(gd->fdt_blob, offset, "reg");
>     +               if (temp != FDT_ADDR_T_NONE) {
>     +                       intc = (microblaze_intc_t *)temp;
>     +                       irq_no = fdtdec_get_int(gd->fdt_blob, offset,
>     + "xlnx,num-intr-inputs", 0);
>     +               }
>     +       }
>     +#endif
>              if (irq_no) {
>                      vecs = calloc(1, sizeof(struct irq_action) * irq_no);
>                      if (vecs == NULL) {
>
>
> I'm not completely clear about whether this should be doing a realloc() (copying the existing array and adding a new member) or not.

I am not sure what you mean by that.
This is done after mem_alloc_init and microblaze u-boot does not any reallocation like other platforms.
Is it what did you mean?

Thanks,
Michal


-- 
Michal Simek, Ing. (M.Eng)
w: www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel 2.6 Microblaze Linux - http://www.monstr.eu/fdt/
Microblaze U-BOOT custodian