[U-Boot] [PATCH 06/12] microblaze: intc: Add device-tree driver configuration

[Michal Simek <monstr@monstr.eu>]

On 07/10/2012 11:02 PM, Simon Glass wrote:
> Hi Michal,
>
> On Tue, Jul 10, 2012 at 11:07 AM, Michal Simek <monstr at monstr.eu <mailto:monstr@monstr.eu>> wrote:
>
>     On 07/09/2012 11:26 PM, Simon Glass wrote:
>
>         Hi Michal,
>
>
>         On Mon, Jul 9, 2012 at 2:20 AM, Michal Simek <monstr at monstr.eu <mailto:monstr@monstr.eu> <mailto:monstr at monstr.eu <mailto:monstr@monstr.eu>>> wrote:
>
>              Read configuration from DTB.
>
>              Signed-off-by: Michal Simek <monstr at monstr.eu <mailto:monstr@monstr.eu> <mailto:monstr at monstr.eu <mailto:monstr@monstr.eu>>>
>
>              ---
>                arch/microblaze/cpu/__interrupts.c |   19 +++++++++++++++++++
>                1 files changed, 19 insertions(+), 0 deletions(-)
>
>              diff --git a/arch/microblaze/cpu/__interrupts.c b/arch/microblaze/cpu/__interrupts.c
>              index 79ee96a..98c9110 100644
>              --- a/arch/microblaze/cpu/__interrupts.c
>              +++ b/arch/microblaze/cpu/__interrupts.c
>              @@ -29,6 +29,9 @@
>                #include <malloc.h>
>                #include <asm/microblaze_intc.h>
>                #include <asm/asm.h>
>              +#include <fdtdec.h>
>              +
>              +DECLARE_GLOBAL_DATA_PTR;
>
>                #undef DEBUG_INT
>
>              @@ -134,10 +137,26 @@ int interrupts_init(void)
>                {
>                       int i;
>
>              +#ifndef CONFIG_OF_CONTROL
>                #if defined(CONFIG_SYS_INTC_0___ADDR) && defined(CONFIG_SYS_INTC_0_NUM)
>                       intc = (microblaze_intc_t *) (CONFIG_SYS_INTC_0_ADDR);
>                       irq_no = CONFIG_SYS_INTC_0_NUM;
>                #endif
>              +#else
>              +       int temp;
>              +       int offset = 0;
>
>
>         I don't think you need the = 0.
>
>
>     Agree. Will remove it.
>
>
>
>              +
>              +       offset = fdt_node_offset_by_compatible(__gd->fdt_blob, offset,
>              + "xlnx,xps-intc-1.00.a");
>              +       if (offset > 0) {
>              +               temp = fdtdec_get_addr(gd->fdt_blob, offset, "reg");
>              +               if (temp != FDT_ADDR_T_NONE) {
>              +                       intc = (microblaze_intc_t *)temp;
>              +                       irq_no = fdtdec_get_int(gd->fdt_blob, offset,
>              + "xlnx,num-intr-inputs", 0);
>              +               }
>              +       }
>              +#endif
>                       if (irq_no) {
>                               vecs = calloc(1, sizeof(struct irq_action) * irq_no);
>                               if (vecs == NULL) {
>
>
>         I'm not completely clear about whether this should be doing a realloc() (copying the existing array and adding a new member) or not.
>
>
>     I am not sure what you mean by that.
>     This is done after mem_alloc_init and microblaze u-boot does not any reallocation like other platforms.
>     Is it what did you mean?
>
> No I just meant that if you had several calls to this it would need to add to the existing list. But I see now that this is just a single item being alloced, so it is fine.

ok.

Thanks,
Michal



-- 
Michal Simek, Ing. (M.Eng)
w: www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel 2.6 Microblaze Linux - http://www.monstr.eu/fdt/
Microblaze U-BOOT custodian