* [U-Boot] [PATCH] mx6: Make pad name macro consistent with the datasheet
@ 2012-06-15 13:48 Ashok
2012-06-15 22:22 ` Marek Vasut
2012-07-07 16:54 ` Stefano Babic
0 siblings, 2 replies; 5+ messages in thread
From: Ashok @ 2012-06-15 13:48 UTC (permalink / raw)
To: u-boot
Use the same name as defined in the datasheet.
DSP_CLK -> DISP_CLK
Signed-off-by: Ashok Kumar Reddy Kourla <ashokkourla2000@gmail.com>
---
arch/arm/include/asm/arch-mx6/mx6x_pins.h | 4 ++--
1 files changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/include/asm/arch-mx6/mx6x_pins.h b/arch/arm/include/asm/arch-mx6/mx6x_pins.h
index afaa068..377d97f 100644
--- a/arch/arm/include/asm/arch-mx6/mx6x_pins.h
+++ b/arch/arm/include/asm/arch-mx6/mx6x_pins.h
@@ -530,8 +530,8 @@ enum {
MX6Q_PAD_EIM_BCLK__IPU1_DI1_PIN16 = IOMUX_PAD(0x046C, 0x0158, 1, 0x0000, 0, 0),
MX6Q_PAD_EIM_BCLK__GPIO_6_31 = IOMUX_PAD(0x046C, 0x0158, 5, 0x0000, 0, 0),
MX6Q_PAD_EIM_BCLK__TPSMP_HDATA_31 = IOMUX_PAD(0x046C, 0x0158, 6, 0x0000, 0, 0),
- MX6Q_PAD_DI0_DISP_CLK__IPU1_DI0_DSP_CLK = IOMUX_PAD(0x0470, 0x015C, 0, 0x0000, 0, 0),
- MX6Q_PAD_DI0_DISP_CLK__IPU2_DI0_DSP_CLK = IOMUX_PAD(0x0470, 0x015C, 1, 0x0000, 0, 0),
+ MX6Q_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK = IOMUX_PAD(0x0470, 0x015C, 0, 0x0000, 0, 0),
+ MX6Q_PAD_DI0_DISP_CLK__IPU2_DI0_DISP_CLK = IOMUX_PAD(0x0470, 0x015C, 1, 0x0000, 0, 0),
MX6Q_PAD_DI0_DISP_CLK__MIPI_CR_DPY_OT28 = IOMUX_PAD(0x0470, 0x015C, 3, 0x0000, 0, 0),
MX6Q_PAD_DI0_DISP_CLK__SDMA_DBG_CR_STA0 = IOMUX_PAD(0x0470, 0x015C, 4, 0x0000, 0, 0),
MX6Q_PAD_DI0_DISP_CLK__GPIO_4_16 = IOMUX_PAD(0x0470, 0x015C, 5, 0x0000, 0, 0),
--
1.7.0.4
^ permalink raw reply related [flat|nested] 5+ messages in thread* [U-Boot] [PATCH] mx6: Make pad name macro consistent with the datasheet
2012-06-15 13:48 [U-Boot] [PATCH] mx6: Make pad name macro consistent with the datasheet Ashok
@ 2012-06-15 22:22 ` Marek Vasut
2012-07-07 16:54 ` Stefano Babic
1 sibling, 0 replies; 5+ messages in thread
From: Marek Vasut @ 2012-06-15 22:22 UTC (permalink / raw)
To: u-boot
Dear Ashok,
> Use the same name as defined in the datasheet.
> DSP_CLK -> DISP_CLK
>
> Signed-off-by: Ashok Kumar Reddy Kourla <ashokkourla2000@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
> ---
> arch/arm/include/asm/arch-mx6/mx6x_pins.h | 4 ++--
> 1 files changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/include/asm/arch-mx6/mx6x_pins.h
> b/arch/arm/include/asm/arch-mx6/mx6x_pins.h index afaa068..377d97f 100644
> --- a/arch/arm/include/asm/arch-mx6/mx6x_pins.h
> +++ b/arch/arm/include/asm/arch-mx6/mx6x_pins.h
> @@ -530,8 +530,8 @@ enum {
> MX6Q_PAD_EIM_BCLK__IPU1_DI1_PIN16 = IOMUX_PAD(0x046C, 0x0158, 1,
0x0000,
> 0, 0), MX6Q_PAD_EIM_BCLK__GPIO_6_31 = IOMUX_PAD(0x046C, 0x0158, 5,
> 0x0000, 0, 0), MX6Q_PAD_EIM_BCLK__TPSMP_HDATA_31 = IOMUX_PAD(0x046C,
> 0x0158, 6, 0x0000, 0, 0), - MX6Q_PAD_DI0_DISP_CLK__IPU1_DI0_DSP_CLK =
> IOMUX_PAD(0x0470, 0x015C, 0, 0x0000, 0, 0),
> - MX6Q_PAD_DI0_DISP_CLK__IPU2_DI0_DSP_CLK = IOMUX_PAD(0x0470, 0x015C, 1,
> 0x0000, 0, 0), + MX6Q_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK =
> IOMUX_PAD(0x0470, 0x015C, 0, 0x0000, 0, 0),
> + MX6Q_PAD_DI0_DISP_CLK__IPU2_DI0_DISP_CLK = IOMUX_PAD(0x0470, 0x015C, 1,
> 0x0000, 0, 0), MX6Q_PAD_DI0_DISP_CLK__MIPI_CR_DPY_OT28 = IOMUX_PAD(0x0470,
> 0x015C, 3, 0x0000, 0, 0), MX6Q_PAD_DI0_DISP_CLK__SDMA_DBG_CR_STA0 =
> IOMUX_PAD(0x0470, 0x015C, 4, 0x0000, 0, 0),
> MX6Q_PAD_DI0_DISP_CLK__GPIO_4_16 = IOMUX_PAD(0x0470, 0x015C, 5, 0x0000,
0,
> 0),
Best regards,
Marek Vasut
^ permalink raw reply [flat|nested] 5+ messages in thread* [U-Boot] [PATCH] mx6: Make pad name macro consistent with the datasheet
2012-06-15 13:48 [U-Boot] [PATCH] mx6: Make pad name macro consistent with the datasheet Ashok
2012-06-15 22:22 ` Marek Vasut
@ 2012-07-07 16:54 ` Stefano Babic
2012-07-11 6:39 ` Dirk Behme
1 sibling, 1 reply; 5+ messages in thread
From: Stefano Babic @ 2012-07-07 16:54 UTC (permalink / raw)
To: u-boot
On 15/06/2012 15:48, Ashok wrote:
>
>
> Use the same name as defined in the datasheet.
> DSP_CLK -> DISP_CLK
>
> Signed-off-by: Ashok Kumar Reddy Kourla <ashokkourla2000@gmail.com>
> ---
Applied to u-boot-imx, thanks.
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 5+ messages in thread
* [U-Boot] [PATCH] mx6: Make pad name macro consistent with the datasheet
2012-07-07 16:54 ` Stefano Babic
@ 2012-07-11 6:39 ` Dirk Behme
2012-07-18 5:23 ` Stefano Babic
0 siblings, 1 reply; 5+ messages in thread
From: Dirk Behme @ 2012-07-11 6:39 UTC (permalink / raw)
To: u-boot
On 07.07.2012 18:54, Stefano Babic wrote:
> On 15/06/2012 15:48, Ashok wrote:
>>
>>
>> Use the same name as defined in the datasheet.
>> DSP_CLK -> DISP_CLK
>>
>> Signed-off-by: Ashok Kumar Reddy Kourla <ashokkourla2000@gmail.com>
>> ---
>
> Applied to u-boot-imx, thanks.
Hmm, this isn't part of v2012.07-rc1? Sorry if I missed something.
Best regards
Dirk
^ permalink raw reply [flat|nested] 5+ messages in thread
* [U-Boot] [PATCH] mx6: Make pad name macro consistent with the datasheet
2012-07-11 6:39 ` Dirk Behme
@ 2012-07-18 5:23 ` Stefano Babic
0 siblings, 0 replies; 5+ messages in thread
From: Stefano Babic @ 2012-07-18 5:23 UTC (permalink / raw)
To: u-boot
On 11/07/2012 08:39, Dirk Behme wrote:
> On 07.07.2012 18:54, Stefano Babic wrote:
>> On 15/06/2012 15:48, Ashok wrote:
>>>
>>>
Hi Dirk,
>>> Use the same name as defined in the datasheet.
>>> DSP_CLK -> DISP_CLK
>>>
>>> Signed-off-by: Ashok Kumar Reddy Kourla <ashokkourla2000@gmail.com>
>>> ---
>>
>> Applied to u-boot-imx, thanks.
>
> Hmm, this isn't part of v2012.07-rc1? Sorry if I missed something.
It is not, I applied it after -rc1.
Cheers,
Stefano
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2012-07-18 5:23 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2012-06-15 13:48 [U-Boot] [PATCH] mx6: Make pad name macro consistent with the datasheet Ashok
2012-06-15 22:22 ` Marek Vasut
2012-07-07 16:54 ` Stefano Babic
2012-07-11 6:39 ` Dirk Behme
2012-07-18 5:23 ` Stefano Babic
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox