[U-Boot] [PATCH 1/2] mmc: at91: add multi block read/write support.

[Josh Wu <josh.wu@atmel.com>]

On 9/13/2012 7:11 PM, Andreas Bie?mann wrote:
> Dear Josh Wu,
>
> sorry for beeing late. Bu2013.01 release.t this submission was way after
> merge window close so it will anyhow end up in 2013.01 release.

OK, no problem.

According to your comments I made the v2 patch and already sent it out. 
Thank you.

Best Regards,
Josh Wu
>
> On 07.09.2012 12:39, Josh Wu wrote:
>> Since the at91sam9263, the mmc hardware support multi blocks read/write. So this driver enable it.
>> This patch also change delay time to max value, which can avoid the timeout error in rare case.
>>
>> Signed-off-by: Josh Wu <josh.wu@atmel.com>
>> ---
>>   drivers/mmc/gen_atmel_mci.c |   16 +++++++++++++---
>>   include/atmel_mci.h         |    5 ++++-
>>   2 files changed, 17 insertions(+), 4 deletions(-)
>>
>> diff --git a/drivers/mmc/gen_atmel_mci.c b/drivers/mmc/gen_atmel_mci.c
>> index 4968c5e..ec075f7 100644
>> --- a/drivers/mmc/gen_atmel_mci.c
>> +++ b/drivers/mmc/gen_atmel_mci.c
>> @@ -24,7 +24,6 @@
>>    * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
>>    * MA 02111-1307 USA
>>    */
>> -
> please leave this line untouched.
>
>>   #include <common.h>
>>   #include <mmc.h>
>>   #include <part.h>
>> @@ -87,6 +86,11 @@ static void mci_set_mode(struct mmc *mmc, u32 hz, u32 blklen)
>>   		 | MMCI_BF(BLKLEN, blklen)
>>   		 | MMCI_BIT(RDPROOF)
>>   		 | MMCI_BIT(WRPROOF)), &mci->mr);
>> +	/*
>> +	 * On some new platforms BLKLEN in mci->mr is ignored.
>> +	 * Should use the BLKLEN in the block register.
>> +	 */
>> +	writel(blklen << MMCI_BLKLEN_OFFSET, &mci->blkr);
> please use the MMCI_BF macro here
>
>>   	initialized = 1;
>>   }
>>   
>> @@ -183,6 +187,12 @@ mci_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, struct mmc_data *data)
>>   	/* Figure out the transfer arguments */
>>   	cmdr = mci_encode_cmd(cmd, data, &error_flags);
>>   
>> +	/* For multi blocks read/write, set the block register */
>> +	if ((cmd->cmdidx == MMC_CMD_READ_MULTIPLE_BLOCK)
>> +			|| (cmd->cmdidx == MMC_CMD_WRITE_MULTIPLE_BLOCK))
>> +		writel(data->blocks | mmc->read_bl_len << MMCI_BLKLEN_OFFSET,
>> +			&mci->blkr);
> please use the MMCI_BF macros here.
>
>> +
>>   	/* Send the command */
>>   	writel(cmd->cmdarg, &mci->argr);
>>   	writel(cmdr, &mci->cmdr);
>> @@ -310,8 +320,8 @@ static int mci_init(struct mmc *mmc)
>>   	writel(MMCI_BIT(MCIEN), &mci->cr);	/* enable mci */
>>   	writel(MMCI_BF(SCDSEL, MCI_BUS), &mci->sdcr);	/* select port */
>>   
>> -	/* Initial Time-outs */
>> -	writel(0x5f, &mci->dtor);
>> +	/* This delay can be optimized, but stick with max value */
>> +	writel(0x7f, &mci->dtor);
> can we split this in a separate patch?
>
>>   	/* Disable Interrupts */
>>   	writel(~0UL, &mci->idr);
>>   
>> diff --git a/include/atmel_mci.h b/include/atmel_mci.h
>> index 3dd5d67..85468d4 100644
>> --- a/include/atmel_mci.h
>> +++ b/include/atmel_mci.h
>> @@ -38,7 +38,7 @@ typedef struct atmel_mci {
>>   	u32	sdcr;	/* 0x0c */
>>   	u32	argr;	/* 0x10 */
>>   	u32	cmdr;	/* 0x14 */
>> -	u32	_18;	/* 0x18 */
>> +	u32	blkr;	/* 0x18 */
>>   	u32	_1c;	/* 0x1c */
>>   	u32	rspr;	/* 0x20 */
>>   	u32	rspr1;	/* 0x24 */
>> @@ -118,6 +118,9 @@ typedef struct atmel_mci {
>>   #define MMCI_TRTYP_OFFSET			19
>>   #define MMCI_TRTYP_SIZE				2
>>   
>> +/* Bitfields in BLKR */
>> +#define MMCI_BLKLEN_OFFSET			16
> NAK, this is defined some lines up (under MR), please add an reminder
> here that it is defined under MR. I wonder if this will produce 'defined
> previously' warnings.
>
>> +
>>   /* Bitfields in RSPRx */
>>   #define MMCI_RSP_OFFSET				0
>>   #define MMCI_RSP_SIZE				32
>>
> Best regards
>
> Andreas Bie?mann